Amend_003_Attach_6_USPP_non_shared_Specifications.pdf

U.S. PARK POLICE

UNIFORM COMPONENT SPECIFICATIONS (Spec 001)

Female LS Lt. Blue Guard Shirt

GENERAL DESCRIPTION

The woven shirt shall have a banded collar, and added length on the sides to accommodate body armor. It shall have mechanical stretch for increased fit and comfort, and creases shall be permanent. Sleeves shall be long and set-in with 2-button cuffs. There shall be 2 chest pockets.

Gender: Female

SALIENT CHARACTERISTICS

Components

* Basic Material: 4.25 oz. sq. yd. 65% polyester/35% cotton twill with filling stretch to enhance comfort and mobility.

* Thread: All thread shall be DTM.

General Instructions

* Stitching: All main, side, and sleeve seams shall be set w/ 1/4” safety stitching.

Detail Design Characteristics

* Collar: The collar shall be banded and top stitched 3/16" from the edge. Permanent collar stays shall be fused or sewn inside collar. The stand shall fasten with one button.

* Sleeves: Each sleeve shall have a one piece pointed placket with one button and buttonhole centered in the vent opening. Cuffs shall close with two buttons and buttonholes, and shall be interlined.

* Pockets: The chest shall have two breast pockets with mitered corners. Both pockets shall have a box-pleat stitched top and bottom. Left pocket shall have a sewn through pencil stall. Woven hook fastener shall be placed on each pocket to secure woven loop fastener placed on each flap.

* Flaps: Flaps shall be scalloped, and have one centered buttonhole with button. The left flap shall have a pencil opening. Woven loop fasteners shall be placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps shall have crease interlining.

* Badgetab: The badgetab shall have small uncut buttonholes 1 ¼” apart with the lower buttonhole 1 ¼” above the flap.

* Epaulets: Sewn shall be sewn into sleeve head seam, and shall be set approximately 1" from the collar seam. They shall be box-stitched to shoulders with a row of x-stitching. Epaulets shall have crease interlining,

* Buttons: The buttons shall be 20-ligne melamine buttons dyed to match the fabric color DTM, shall be break-resistant.

* Creasing: The two military creases in front and three in back of each shirt incorporate a permanent silicone crease.

* Patch: The United States Park Police (USPP) emblem EM3481 shall be added to both left and right sleeves, in RES at time of order.

Sizes: S - 2XL

UNIFORM COMPONENT SPECIFICATIONS (Spec 002)

Male LS Lt. Blue Guard Shirt

The woven shirt shall have a banded collar, and added length on the sides to accommodate body armor. It shall have mechanical stretch for increased fit and comfort, and creases shall be permanent. Sleeves shall be long and set-in with 2-button cuffs. There shall be 2 chest pockets.

Gender: Male

SALIENT CHARACTERISTICS

Components

* Basic Material: 4.25 oz. sq. yd. 65% polyester/35% cotton twill with filling stretch to enhance comfort and mobility.

* Thread: All thread shall be DTM.

General Instructions

* Stitching: All main, side, and sleeve seams shall be set w/ 1/4” safety stitching.

Detail Design Characteristics

* Collar: The collar shall be banded and top stitched 3/16" from the edge. Permanent collar stays shall be fused or sewn inside collar. The stand shall fasten with one button.

* Sleeves: Each sleeve shall have a one piece pointed placket with one button and buttonhole centered in the vent opening. Cuffs shall close with two buttons and buttonholes, and shall be interlined.

* Pockets: The chest shall have two breast pockets with mitered corners. Both pockets shall have a box-pleat stitched top and bottom. Left pocket shall have a sewn through pencil stall. Woven hook fastener shall be placed on each pocket to secure woven loop fastener placed on each flap.

* Flaps: Flaps shall be scalloped, and have one centered buttonhole with button. The left flap shall have a pencil opening. Woven loop fasteners shall be placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps shall have crease interlining.

* Badgetab: The badgetab shall have small uncut buttonholes 1 ¼” apart with the lower buttonhole 1 ¼” above the flap.

* Epaulets: Sewn shall be sewn into sleeve head seam, and shall be set approximately 1" from the collar seam. They shall be box-stitched to shoulders with a row of x-stitching. Epaulets shall have crease interlining,

* Buttons: The buttons shall be 20-ligne melamine buttons dyed to match the fabric color DTM, shall be break-resistant.

* Creasing: The two military creases in front and three in back of each shirt incorporate a permanent silicone crease.

Sizes:

14.5 15 15.5 16 16.5 17 17.5 18 18.5 32 x x x x 33 x x x x x x x x 34 x x x x x x x x 35 x x x x x x x 36 x x x x x x x

UNIFORM COMPONENT SPECIFICATIONS (Spec 003)

Female SS Lt. Blue Guard Shirt

The woven shirt shall have a banded collar, and added length on the sides to accommodate body armor. It shall have mechanical stretch for increased fit and comfort, and creases shall be permanent. Sleeves shall be short, hemmed, and set-in. There shall be 2 chest pockets.

Gender: Female

SALIENT CHARACTERISTICS

Components

* Basic Material: 4.25 oz. sq. yd. 65% polyester/35% cotton twill with filling stretch to enhance comfort and mobility.

* Thread: All thread shall be DTM.

General Instructions

* Stitching: All main, side, and sleeve seams shall be set w/ 1/4” safety stitching.

Detail Design Characteristics

* Collar: The collar shall be banded and top stitched 3/16" from the edge. Permanent collar stays shall be fused or sewn inside collar. The stand shall fasten with one button.

* Sleeves: Sleeves are short, one piece, and hemmed. Sleeve setting and closing are sewn with an overedge and safety stitch. The sleeve is bartacked at the hem.

* Pockets: The chest shall have two breast pockets with mitered corners. Both pockets shall have a box-pleat stitched top and bottom. Left pocket shall have a sewn through pencil stall. Woven hook fastener shall be placed on each pocket to secure woven loop fastener placed on each flap.

* Flaps: Flaps shall be scalloped, and have one centered buttonhole with button. The left flap shall have a pencil opening. Woven loop fasteners shall be placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps shall have crease interlining.

* Badgetab: The badgetab shall have small uncut buttonholes 1 ¼” apart with the lower buttonhole 1 ¼” above the flap.

* Epaulets: Sewn shall be sewn into sleeve head seam, and shall be set approximately 1" from the collar seam. They shall be box-stitched to shoulders with a row of x-stitching. Epaulets shall have crease interlining,

* Buttons: The buttons shall be 20-ligne melamine buttons dyed to match the fabric color DTM, shall be break-resistant.

* Creasing: The two military creases in front and three in back of each shirt incorporate a permanent silicone crease.

Sizes: S - 2XL

UNIFORM COMPONENT SPECIFICATIONS (Spec 004)

Male SS Lt. Blue Guard Shirt

The woven shirt shall have a banded collar, and added length on the sides to accommodate body armor. It shall have mechanical stretch for increased fit and comfort, and creases shall be permanent. Sleeves shall be short, hemmed, and set-in. There shall be 2 chest pockets.

Gender: Male

SALIENT CHARACTERISTICS

Components

* Basic Material: 4.25 oz. sq. yd. 65% polyester/35% cotton twill with filling stretch to enhance comfort and mobility.

* Thread: All thread shall be DTM.

General Instructions

* Stitching: All main, side, and sleeve seams shall be set w/ 1/4” safety stitching.

Detail Design Characteristics

* Collar: The collar shall be banded and top stitched 3/16" from the edge. Permanent collar stays shall be fused or sewn inside collar. The stand shall fasten with one button.

* Sleeves: Sleeves are short, one piece, and hemmed. Sleeve setting and closing are sewn with an overedge and safety stitch. The sleeve is bartacked at the hem.

* Pockets: The chest shall have two breast pockets with mitered corners. Both pockets shall have a box-pleat stitched top and bottom. Left pocket shall have a sewn through pencil stall. Woven hook fastener shall be placed on each pocket to secure woven loop fastener placed on each flap.

* Flaps: Flaps shall be scalloped, and have one centered buttonhole with button. The left flap shall have a pencil opening. Woven loop fasteners shall be placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps shall have crease interlining.

* Badgetab: The badgetab shall have small uncut buttonholes 1 ¼” apart with the lower buttonhole 1 ¼” above the flap.

* Epaulets: Sewn shall be sewn into sleeve head seam, and shall be set approximately 1" from the collar seam. They shall be box-stitched to shoulders with a row of x-stitching. Epaulets shall have crease interlining,

* Buttons: The buttons shall be 20-ligne melamine buttons dyed to match the fabric color DTM, shall be break-resistant.

* Creasing: The two military creases in front and three in back of each shirt incorporate a permanent silicone crease.

14.5 15 15.5 16 16.5 17 17.5 18 18.5 SS x x x x x x x x x

- 1 -

US PARKS POLICE

UNIFORM COMPONENT SPECIFICATION (Spec 005) Unisex Tan Long Sleeve Polo

SALIENT CHARACTERISTICS

Components

Basic Fabric: Dri-Balance™ 60% Cotton / 40% Polyester, 220 grams per square meter (6.0 oz/sq. yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri-Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

Design: The design of this long sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves with dyed-to-match rib knit cuffs, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible Interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button.

All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible interlining. The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

- 2 -

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are finished with dyed-to-match rib knit cuffs finishing 2½” in length.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam.

The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish.

The pocket bag measures 2” long X 2½” wide.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve cuff. This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape.

The bottom of the shirt is hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police direct embroidery (ELD163) to the left upper front.

- 3 -

UNIFORM COMPONENT SPECIFICATION (spec 006)

Description: Unisex Tan Short Sleeve Polo

Basic Fabric: Dri-Balance™ 60% Cotton / 40% Polyester, 220 grams per square meter (6.0 oz/sq.

yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri-Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

Design: The design of this short sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button. All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible interlining.

The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are hemmed using a 1” turn up and double needle cover-stitch.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish.

The pocket bag measures 2” long X 2½” wide.

There is a two stall double welt pencil pocket centered on the left raglan sleeve, 1 ½” above the sleeve hem. It measures 5 ¾” deep and 1 ¾” wide. The underside of the pocket is turned under and clean finished.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve hem. This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt and sleeves are hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police direct embroidery (ELD163) to the left upper front.

US PARK POLICE

UNIFORM COMPONENT SPECIFICATION (Spec 0070

Unisex Navy Training Branch Long Sleeve Polo

Basic Fabric: Dri-Balance™ 60% Cotton / 40% Polyester, 220 grams per square meter (6.0 oz/sq. yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri- Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

appearance while providing multi-faceted functionality. The polo has such features as:

cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves with dyed-to-match rib knit cuffs, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible Interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button. All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible interlining. The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are finished with dyed-to-match rib knit cuffs finishing 2½” in length.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish. The pocket bag measures 2” long X 2½” wide.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve cuff. This design creates a seamless gusset, providing 360º range of movement.

The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt is hemmed using a double needle cover-stitch.

Color: Navy Blue

Customization: Add an official U.S. Parks Police Instructor direct embroidery to the left upper front.

UNIFORM COMPONENT SPECIFICATION (008)

Description: Unisex Navy Short Sleeve Training Branch Instructor Polo

Basic Fabric: Dri-Balance™ 60% Cotton / 40% Polyester, 220 grams per square meter (6.0 oz/sq. yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri- Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

Design: The design of this short sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as:

cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button. All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible interlining. The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are hemmed using a 1” turn up and double needle cover-stitch.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish. The pocket bag measures 2” long X 2½” wide.

There is a two stall double welt pencil pocket centered on the left raglan sleeve, 1 ½” above the sleeve hem. It measures 5 ¾” deep and 1 ¾” wide. The underside of the pocket is turned under and clean finished.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve hem. This design creates a seamless gusset, providing 360º range of movement.

The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt and sleeves are hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police Instructor direct embroidery to the left upper front.

Color: Navy Blue

US PARK POLICE

UNIFORM COMPONENT SPECIFICATION (Spec 009)

Unisex Black Long Sleeve Polo – Communications Section meter 6.0 oz/sq. yd.), plated knit giving a jersey face (cotton) and mesh back appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves with dyed-to-match rib knit cuffs, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button.

All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The fusible Interlining. The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned

Sleeves The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are finished with dyed-to-match rib knit cuffs finishing 2½” in length.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish. The pocket bag measures 2” long X 2½” wide.

Side Panels

The polo features straight side panels, extending from the shirt-tail hem to the sleeve cuff.

This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching

All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt is hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police Communications Section direct embroidery to the left upper front.

UNIFORM COMPONENT SPECIFICATION

Description: Unisex Black Short Sleeve Polo – Communications Section meter (6.0 oz/sq. yd.), plated knit giving a jersey face (cotton) and mesh back

Design: The design of this short sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button.

All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The fusible interlining. The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are hemmed using a 1” turn up and double needle

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam.

The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish.

There is a two stall double welt pencil pocket centered on the left raglan sleeve, 1 ½” above the sleeve hem. It measures 5 ¾” deep and 1 ¾” wide. The underside of the pocket is turned under and clean finished.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve hem. This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape.

The bottom of the shirt and sleeves are hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police Communications direct embroidery to the left upper front.

UNIFORM COMPONENT SPECIFICATION (Spec 0011)

Description: Unisex Black Long Sleeve Polo yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri-Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

Design: The design of this long sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves with dyed-to-match rib knit cuffs, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button. All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible interlining.

The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

Sleeves

The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are finished with dyed-to-match rib knit cuffs finishing 2½” in length.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish. The pocket bag measures 2” long X 2½” wide.

Side Panels The polo features straight side panels, extending from the shirt-tail hem to the sleeve cuff. This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt is hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police Marine Unit direct embroidery onto the left upper front.

U.S. Parks Police reflective heat seal at the center middle back 6” down from the center back neck seam.

- 4 -

UNIFORM COMPONENT SPECIFICATION (Spec 0012)

Unisex Black Short Sleeve Polo yd.), plated knit giving a jersey face (cotton) and mesh back (polyester). Dri-Balance™ technology is specially designed to optimize breathable and absorptive properties to keep a wearer dry and comfortable in all activities.

Design: The design of this short sleeve, unisex polo has a technical and professional appearance while providing multi-faceted functionality. The polo has such features as: cutting edge fabric performance, dyed-to-match no-curl collar, 3-button placket, raglan sleeves, seamless-gusset straight side panels with bottom vents, 3 mic holders, double-layer back sweat patch and twill tape reinforced collar, raglan sleeve and side vent seams.

Front: Center placket finishes 1¼” wide X 6½” long. Both the top and bottom plackets have fusible interlining. The top placket is edge stitched and has a ½” horizontal box-stitch at the bottom. The top button hole is horizontal and positioned ½” below the top edge. The 2nd and 3rd button holes are vertical. The 2nd button is placed 2” below the top button and the 3rd button is placed 2” below the 2nd button. All button holes measure 5/8” wide. The bottom placket is edge stitched on all sides and has three buttons that correspond with the buttonholes on the top placket. The 19-Ligne, 4-eye buttons match the body and are pearlized. The inside bottom edge of the placket is neatly serged to finish.

There is a ½” wide mic loop at the base of the placket. This loop is reinforced with fusible Interlining.

The right side of the loop is inserted between the top and bottom placket layers, caught with the bottom box stitch. The left side of the loop is turned under and then edge tacked. Both ends of the loop are reinforced with a bartack, giving a 1-1/8” opening.

Collar: The collar is ribbed knit and dyed-to-match the body fabric. The collar measures 3” wide at center back and 2½” wide at each collar point. Each collar point contains a concealed Mylar stay, preventing “collar point curl-up”. The collar seam is reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape.

Sleeves: The polo features raglan style sleeves (upper portion), combined with a straight side panel, seamless gusset (bottom portion), providing 360º range of movement. Raglan seams are reinforced with 3/8” wide dyed-to-match, 100% cotton twill tape. The sleeves are hemmed using a 1” turn up and double needle cover-stitch.

There is a concealed mic pocket located on each front raglan sleeve seam. This placement is off the top of the shoulder providing “ergonomic” mic placements for those wearers using a radio mic. The pocket is located 3½” from the collar seam. The pocket opening measures 1½” wide and is reinforced on each end with a bartack. The top edge of the interior pocket bag is reinforced, being caught under the raglan sleeve seam twill tape. The remaining 3 sides are serged for a neat finish.

There is a two stall double welt pencil pocket centered on the left raglan sleeve, 1 ½” above the sleeve hem. It measures 5 ¾” deep and 1 ¾” wide. The underside of the pocket is turned under and clean finished.

Side Panels: The polo features straight side panels, extending from the shirt-tail hem to the sleeve hem. This design creates a seamless gusset, providing 360º range of movement. The side panel grades in width, measuring 8¼” at the shirt-tail hem and 5¼” at the sleeve hem. The bottom edge of each panel has a vent reinforced with twill tape, measuring 2½” in length.

Hem: The bottom of the shirt is hemmed using a 1” turn up and double needle cover-stitch.

Stitching: All seams are safety-stitched using 11 to 12 stitches per inch. The collar, raglan sleeve and vent seams are reinforced with 3/8” wide, 100% cotton twill tape. The bottom of the shirt and sleeves are hemmed using a double needle cover-stitch.

Customization: Add an official U.S. Parks Police Marine Unit direct embroidery to the left upper front. Add U. S. Parks Police reflective heat seal to the center middle back 6” down from the center back neckseam.

UNIFORM COMPONENTS SPECIFICATIONS (Spec 0013)

Specifications: Two Pocket Rip Stop BDU Shirt

Propper Black: 65% Poly / 35% Cotton Ripstop BDU 2-Pocket shirt

SALIENT CHARACTERISTICS

Components

Features

• Designed to Tuck In

• Fused Pocket Flaps and Collar

• 2-Piece Double Reinforced Elbows

• Chest Pencil Pocket

• Felled Side Seams and Sleeves

• Two Shoulder Epaulets with Buttons

• Adjustable Sleeve Buttons

• 2 ½” Cuffs

• Made in the USA/ Imported

Customization

Apply official U.S. Parks Police emblem to both sleeves 1” below the sleeve set seam, centered with epaulet. Add embroidered nametape to the left upper of the garment, centered above the pocket. Embroider with first initial and last name in ALL CAPS.

Apply loop tape to the right upper front of the garment, centered above the pocket.

UNIFORM COMPONENT SPECIFICATION (Spec 0014)

Specifications: Men’s Black Dress Trousers, Summer Weight

Basic Material: 55% Polyester/45% Wool, Black with Light Blue Stripe

Design: Shall be made on a uniform pattern, having a plain front with straight side pockets, and two back pockets with flaps.

Pockets: The side pockets shall have a minimum opening of 6½” and shall be approximately 5" deep from the bottom of the opening. They will be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1¼” wide. The back pockets will have a minimum opening of 6" and will be 6" deep. Sizes 29 and smaller will have a minimum opening of 5”. They shall be made with a Reese PW automatic machine and finished on the outside with an exposed top and bottom cord. Each back pocket shall have a button through pocket flap to close. All pockets are to be bar tacked with a triangular bar tacking machine.

Pocketing: All pocketing shall be black, 75% polyester / 25% cotton with a minimum thread count of 86 x 56. The weight shall be 3.0 yds/lb.

Waistband: The waistband shall be 2” wide and shall close with a crush-proof hook and eye, the eye being bar tacked for stability. Stretch Ban-Rol III waistband stiffener, ¾” in width, shall be sewn into the top of the waistband to prevent rollover. The trousers are to be made with a continuous closed waistband. The waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

The inner waistband shall be composed of a one-piece elastic web. This web shall contain a blend of 42% Nylon / 20% Polyester / 14% Neoprene Rubber (3 strands) / 6% Lycra / 18% Cotton. The elastic web shall be constructed so that the cotton content of the band is in the upper 1-1/8” portion where the pressure of the belt would require the wicking properties of cotton close to the body to maintain comfort. The remainder of the band will be woven with an open mesh construction to promote breathability in the hip area.

Additionally, the web will have 35% stretch and be 3” wide. The web will be sewn at the top and at the bottom waistband seams which will reduce its stretch in the upper area to allow for a comfortable fit at the waist when bending or sitting. The upper portion of the web shall have a stiffness of .09 oz. of torque (as specified in FED-STD-191, Method

5202) to prevent waistband rollover. The lower part of the web will be left free to stretch over the hips and give support to the back and abdomen. This lower high-stretch area will have pressure applied to it by the hips, preventing the trouser from slipping down while being worn. Three rows of exposed rubber woven into the center off the web will insure that the shirt remains tucked in for neat appearance.

Inside Trim: The right fly lining will be the same fabric and color as the pocketing and shall be sewn to the left fly below the zipper. A separate French fly made of the outer fabric shall be sewn to the inside right fly.

Belt Loops: There shall be four (4) tunnel belt loops and one ¾” center back loop on waist sizes 30 and down, seven (7) tunnel belt loops on waist sizes 31 - 48, and nine (9) on sizes 50 and larger. Each tunnel loop is to be 2-1/8" wide and stitched on the face side with a two needle machine. Except for the center back loop which shall be tacked on, all loops will be sewn into the bottom of the waistband and into the rocap. They shall accommodate a 1-5/8" belt.

Zipper: The trousers shall be closed with a YKK brass zipper which has a brass bottom stop at the base of the zipper chain and a brass ratcheting cam lock slider. The inside left fly will be reinforced with Pellon under the zipper stitching. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located below the bottom zipper stop on the inside of the trouser.

Seaming: The entire trouser is to be seamed with polyester core thread. The seat seam shall be stitched with a tandem needle seat seaming machine. All exposed inside seams of the trouser are to be surged.

Finishing and Pressing: All loose threads shall be removed. Trousers must be pressed completely and properly with the side seam, inseam, and seat seam pressed open.

Customization: 2” True Blind-stitch Hem, cut only at the time of order.

UNIFORM COMPONENT SPECIFICATION (Spec 0015)

Specifications: Men’s Black Dress Trousers, Winter Weight

Basic Material: 55% Polyester/ 45% Wool, Black with Light Blue Stripe

Design: Shall be made on a uniform pattern, having a plain front with straight side pockets, and two back pockets with flaps.

Pockets: The side pockets shall have a minimum opening of 6½” and shall be approximately 5" deep from the bottom of the opening. They will be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1¼” wide. The back pockets will have a minimum opening of 6" and will be 6" deep. Sizes 29 and smaller will have a minimum opening of 5”. They shall be made with a Reese PW automatic machine and finished on the outside with an exposed top and bottom cord. Each back pocket shall have a button through pocket flap to close. All pockets are to be bar tacked with a triangular bar tacking machine.

Pocketing: All pocketing shall be black, 75% polyester / 25% cotton with a minimum thread count of 86 x 56. The weight shall be 3.0 yds/lb.

Waistband: The waistband shall be 2” wide and shall close with a crush-proof hook and eye, the eye being bar tacked for stability. Stretch Ban-Rol III waistband stiffener, ¾” in width, shall be sewn into the top of the waistband to prevent rollover. The trousers are to be made with a continuous closed waistband. The waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain.

The inner waistband shall be composed of a one-piece elastic web. This web shall contain a blend of 42% Nylon / 20% Polyester / 14% Neoprene Rubber (3 strands) / 6% Lycra / 18% Cotton. The elastic web shall be constructed so that the cotton content of the band is in the upper 1-1/8” portion where the pressure of the belt would require the wicking properties of cotton close to the body to maintain comfort. The remainder of the band will be woven with an open mesh construction to promote breathability in the hip area. Additionally, the web will have 35% stretch and be 3” wide. The web will be sewn at the top and at the bottom waistband seams which will reduce its stretch in the upper area to allow for a comfortable fit at the waist when bending or sitting. The upper portion of the web shall have a stiffness of .09 oz. of torque (as specified in FED-STD-191, Method 5202) to prevent waistband rollover. The lower part of the web will be left free to stretch over the hips and give support to the back and abdomen. This lower high-stretch area will have pressure applied to it by the hips, preventing the trouser from slipping down while being worn. Three rows of exposed rubber woven into the center off the web will insure that the shirt remains tucked in for neat appearance.

Inside Trim: The right fly lining will be the same fabric and color as the pocketing and shall be sewn to the left fly below the zipper. A separate French fly made of the outer fabric shall be sewn to the inside right fly.

Belt Loops: There shall be four (4) tunnel belt loops and one ¾” center back loop on waist sizes 30 and down, seven (7) tunnel belt loops on waist sizes 31 - 48, and nine (9) on sizes 50 and larger. Each tunnel loop is to be 2-1/8" wide and stitched on the face side with a two needle machine. Except for the center back loop which shall be tacked on, all loops will be sewn into the bottom of the waistband and into the rocap. They shall accommodate a 1-5/8" belt.

Zipper: The trousers shall be closed with a YKK brass zipper which has a brass bottom stop at the base of the zipper chain and a brass ratcheting cam lock slider.

The inside left fly will be reinforced with Pellon under the zipper stitching. A straight bar tack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bar tack located below the bottom zipper stop on the inside of the trouser.

Seaming: The entire trouser is to be seamed with polyester core thread. The seat seam shall be stitched with a tandem needle seat seaming machine. All exposed inside seams of the trouser are to be serged.

Finishing and Pressing: All loose threads shall be removed. Trousers must be pressed completely and properly with the side seam, inseam, and seat seam pressed open.

UNIFORM COMPONENT SPECIFICATION (Spec 0016)

Specifications: Women’s Black Dress Trousers, Summer Weight

Design: Shall be made on a modified ladies uniform pattern with one dart on each front panel, straight side pockets, two back pockets and elastic in the back waistband.

Pockets: The front pocket opening will be a minimum 5-1/2" and be 6" deep from the bottom of the opening. They shall be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1-1/4" wide. The back pockets will have a minimum opening of 5-1/2" and be 6" deep on size 14 and up. On size 12 and down, the minimum opening will be 5" wide and 6" deep. They shall be made with a Reese PW automatic machine and finished on the outside with an exposed top and bottom cord. All pockets shall be bar tacked with a triangular bar tacking machine.

Pocketing: All pocketing shall be tan, 75% polyester / 25% cotton with a minimum thread count of 86 X 56. The weight shall be 3.0 yds/lb.

Pocket Flaps: Each hip pocket shall close with a pointed, button through flap made of self goods.

Waistband:…