Amend_003_Attach_3_NPS_non_shared_Specifications.pdf

NATIONAL PARK SERVICE

UNIFORM COMPONENTS SPECIFICATIONS (UNISEX) (Spec 001)

Unisex Black Balaclava

Gender: Unisex

General Description: Balaclava.

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• The fabric content shall be a performance material

• The fabric weight shall be suitable for cold climates

Salient Characteristics:

• The color shall be black.

• Breathable, 4-way stretch

• Moisture wicking comfort

Customization: N/A

Stock Sizes: One Size

U. S. NATIONAL PARKS SERVICE

UNIFORM COMPONENT SPECIFICATIONS (002)

Velcro Park Ranger Badge Emblem

GENERAL DESCRIPTION

The emblem shall be 2.375” X 3.375” with hook and loop backing.

Gender: N/A

SALIENT CHARACTERISTICS

Components

* Background Fabric: The twill background material must be first quality and cannot be mill seconds. The material must be a colorfast (able to withstand commercial light color classification laundering and commercial dry-cleaning) fine line twill six and one half to seven ounces per square yard, 100% polyester or cotton/polyester (50% or more polyester content) permanent press, cured and pre-shrunk (resin impregnated and oven cured). Component testing by a certified independent laboratory may be required.

* Embroidery:

a. Emblems must be machine embroidered on embroidery machines with numerical control devices. Embroidery done on Multi-head or Schiffli machines is allowed as long as the quality of the embroidery meets or exceeds the control samples.

b. Thread must be continuous filament bright 120/2 denier (or finer) polyester. Refer to the individual emblem illustrations for applicable thread size.

c. The thread must be a colorfast and must not fade crock, bleed, sublimate, or otherwise transfer or loose color and must be able to withstand commercial light color classification laundering and commercial dry-cleaning.

d. Stitch scale must be of sufficient density to preclude “bleeding” through of the background material color. There must be sufficient underlay stitching to give a full three-dimensional appearance to the design.

e. Double thread will not be permitted in any part of this emblem. Single thread stitching must be used throughout.

f. The minimum stitch count for this emblem is 12522 Multi-head Revolutions

g. The Embroidery Colors are: BROWN (PMS MATCH- 7504), GOLD (PMS MATCH- 7407), Metallic

Gold (PMS MATCH- N/A)

* Overlock Border:

a. The top portion of the overlock border must consist of one end of 300 denier 4 ply polyester ,or two separate ends of 300 denier 2 ply polyester or five separate ends of 150 denier 2 ply rayon or 135 denier 2 ply polyester.

b. The bottom portion of the overlock border must consist of separate ends of cotton or cotton polyester core wrapped thread in a matching color to the top portion of the overlock. Clear monofilament is not permitted.

c. The overlock edge must be overrun a minimum of 3/8", and the end threads must be securely fastened to the back of the emblem or pulled through the entire length of the overrun. Neither method should affect the appearance of the emblem after attachment or make the emblem difficult to attach. Securing overrun with tape will not be permitted.

d. The manufacturer must certify that the overlock border will be applied in such a manner as to prevent it from pulling loose from the emblem, which it will be of a density sufficient to completely cover the fabric edge of the emblem, and that after proper attachment to a garment it will not curl after washing or dry cleaning.

* Finishing:

a. A plastic film or plasticized non-woven must be bonded to the reverse side of the emblem with sufficient heat and pressure to cause the film to melt and bond to the fabric and bobbin threads. The film used must be able to withstand temperatures in excess of 300 degrees F in an alkaline solution and must be non-soluble in all commercial laundering fluids. Coating or film must NOT be chlorine retentive, nor should it emit toxic gases when subject to heat.

b. The backing must be applied in such a manner as to preclude crushing flattening or depressing of the embroidery, nor there be any jump or connecting stitch indentations or depressions in the embroidery caused by pressure during finishing.

c. The backing material must completely coat all raised elements on the back of the emblem and fill all depressions.

d. The finished emblem must be cut to the exact shape, size and geometry of the approved design.

* Workmanship:

a. There is to be no distortion of the exterior shape of the emblem.

b. The finished emblem must show a clear-cut execution and must be clean; neatly made and with full tension on all threads.

c. The finished product must show no broken stitches, nor may any stitches be out of proper alignment.

d. Any repairs or mending must be done so that they do not affect the appearance or serviceability of the emblem.

e. The emblem must not curl and must appear flat and smooth after attachment.

f. The finished product must conform to the quality standard of this specification in all characteristics.

U.S. NATIONAL PARK SERVICE

UNIFORM COMPONENT SPECIFICATIONS (Spec 003)

24 Ligne Shank Buttons 36 Ligne Shank Buttons

GENERAL DESCRIPTION

These are metal acid bronze buttons that are used for the Ike jacket and Dress coat in the National Parks Service Program.

SALIENT CHARACTERISTICS

Components

* Construction: The metal bronze button shall have a vertical shank on the center back of the button. The artwork embossed on the button shall be specific to the National Parks Service. It shall be an eagle on an olive branch with the following script circling the edge “NATIONAL PARK SERVICE* DEPT. OF THE

INTERIOR.”

* Basic:

24 Ligne Button is produced by Waterbury button, vendor style # 1107802436C0422 36 Ligne Button is produced by Waterbury Button, vendor style #1107803634C0422

36 LIGNE

24 LIGNE

UNIFORM COMPONENT SPECIFICATIONS

DRESS COAT (Spec 004 and 004a)

The coat shall be semi-fitted style, single breasted with 4-button front and notch lapels. Single vent back, bi-swing belted back. Coat construction shall be used throughout. Body and sleeves shall be fully lined.

The sample size for the male coat is a size 42 Regular.

The sample size for the female jacket is size 14 Regular.

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

Worn with the dress uniform or ceremonial dress The fit shall be tailored and allow for comfortable wear over a dress shirt The fabric shall be a performance blend material The fabric weight shall be suitable for both indoor and outdoor environment The fabric shall be wrinkle resistant The tailoring shall conform to true male sizing The tailoring shall conform to true female sizing

COLOR CHARACTERISTICS

Forest Green

SALIENT CHARACTERISTICS

Components

* Linings: The lining material for lining fronts, sleeves, inside pockets, outside pocket flaps, yoke and back vent should be Rayon, 3.7 ounces per square yard. Color should be black.

* Thread: All thread should be appropriate for the construction and purpose of the jacket. The color of the thread should match the shade of the body fabric. Button holes should be reinforced with thread appropriate for that purpose.

* Buttons: Shall have 4 front NPS 36-ligne buttons with stay button and one 24-ligne button with rings on each pocket flap.

* Badge Holder: Black enameled badge holder, Waterbury No. 9705, or equal.

General Instructions

* Button Holes: Front buttonholes should be cut-after type. Pocket flaps should have buttonhole with button fastened by “O” rings under flap.

Detail Design Characteristics

* Collar: The collar should be lined with high quality collar canvas. The under collar should be made of all wool under collar cloth, which should be blind stitched to the jacket. Collar height in back should be 1 5/8” with ¼” topstitching from edge.

* Front: Coat should have a fused front and a separate fused chest piece. Only a high quality woven fusible canvas should be acceptable. Fusing should be done on a tray feed or belt driven fusing press to insure proper bonding. Coat construction using Hymo canvas and haircloth basted to the coat fronts may also be used. The inside facing with a minimum of 4” should be made of the same goods as the outer fabric. The front buttonholes should be cut-after type. There should be a 2-piece back with a single vent measuring a minimum of 9”. The shoulders are to have pads and sleeve heads. The arm holes, vents, and front edges should be taped. The armholes are to have shields made of outer fabric. The top sleeve linings should be machine stitched.

* Lapels: Notched lapel should measure 1-1/2” with edge stitching 1/4” on front.

* Linings: To be fully lined. Bottom of the lining should be no more than 1” from the bottom of the coat and be turned up ½”. Sleeve lining should be the same as the body lining and be no more than 2” from the bottom of the sleeve.

* Badge Reinforcements: Badge holder should be placed ½” above the left pocket flap, centered and should be sewn on by hand through outer layer only.

* Pocket Flaps: There should be 4 front pocket flaps with no pockets. Top flaps should be scalloped, and sewn down at sides, 5 ½” wide, 2 3/8” at sides and 3 ¼” at center point. Lower pocket flaps should be scalloped, 7 ¼” wide, 2 ¾” at sides and 3 3/8” at center point. Flaps should have buttonhole with button fastened by “O” rings under flap. Flaps should be lined with lining material.

* Pockets: Two inside pockets should be single welt style. Inside pockets should be made of lining fabric and measure 6” wide by 6 ½” deep.

* Back: The coat should have a bi-swing belted back. The bi-swing back should be sewn into the shoulder seam 3/8” from each armhole seam. The bi-swing fold back should be 1 ½". The facing should be stitched closed on each side 2 ½” to 3” from the shoulder seam into the side panels. There should be a back belt, 2” wide at the waist. The bi-swing should be inserted in the belt top. Belt should be topstitched ¼” on top and bottom.

* Sleeves: The sleeves should be regular coat style, set in with single needle. They should have a minimum

2” hem for alteration. The bottom of the sleeves should be lined with wigan.

* Patch: An arrowhead patch should be sewn securely in the center of the left sleeve with the top edge 1 ¼” to 1 ½” below the shoulder seam depending on the garment size. The patch should be sewn with inconspicuous stitching using brown thread closely matching the emblem background color.

Sizes:

MALE

Short 36 – 46 even Regular 36 – 54 even Long 38 – 54 even X-Long 40 – 48 even

FEMALE

Petite 4 – 14 even

Regular 2 – 24 even Tall 8 – 24 even

IMAGES

Men’s Summer Dress Coat

Men’s Winter Dress Coat

Women’s Summer Dress Coat

Women’s Winter Dress Coat

UNIFORM COMPONENT SPECIFICATIONS (UNISEX)(Spec 005)

Field Jacket Liner

Sample Size: Small

GENERAL DESCRIPTION

Quilted Jacket Liner for Field Jacket

Gender: Unisex

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• Worn as a liner for the Field Jacket

• The fit shall be comfortable and allow for full range of motion

• The fabric weight shall be suitable for cold weather conditions

• The fabric shall be machine-washable

SALIENT CHARACTERISTICS

Components

* Basic Material: The body should be Black 5 ounce bonded polyester fiberfill 3” point to point Diamond quilted with 70 denier nylon taffeta face and 50 denier nylon taffeta back. The sleeves should be Black 3 ounce bonded polyester fiberfill 3” point Diamond quilted with 70 denier nylon taffeta face and 50 denier nylon taffeta back.

* Thread: The entire garment should be sewn with polycore or 100% spun polyester thread.

* Zippers: There should be an interlining zipper, double shrunk, center marked, and interchangable attached to the liner. The zipper should be of sufficient length to be satisfactorily attached to the facing of the jacket.

General Instructions

* Stitching: The exposed body seams should be bound with 1 9/16” black rayon bias binding. The side seams, shoulder seams, and sleeve seams should be joined with a serge sew safety stitch machine.

Detail Design Characteristics

* Front: The lining is curved at the base of the zipper.

* Sleeves: Bound with 9/16” black rayon bias binding.

Sizes Short M Regular XS – 3XL Long M – 3XL

UNIFORM COMPONENT SPECIFICATIONS (UNISEX)(Spec 006)

Field Jacket

Sample Size: Unisex

GENERAL DESCRIPTION

Permanent press jacket with zipper from bottom of jacket to bottom of collar, two piece convertible collar, with two outside breast pockets with pointed flaps. This jacket should be designed to allow a liner to be placed inside for colder climates. This jacket comes in two versions: 1)With Badge Tab and Name Plate Holder and 2) Without Badge Tab and Name Plate Holder

Gender: Unisex

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• Worn in an indoor/outdoor environment

• The fit shall be comfortable and allow for full range of motion

• The fabric weight shall be suitable for all weather conditions

• The fabric shall be machine-washable

• The fabric shall resist fading

• The fabric shall resist stains

• The fabric shall be wrinkle resistant

SALIENT CHARACTERISTICS

Components

* Basic Material: The material should be Forest Green.

* Thread: The thread for all sewing operations should be Rayon covered polyester or 100% spun polyester, dyed to match shade of self material, conforming to ticket number 50-2 or 3 ply and 70-2 or 3 ply of MIL- T-43548. All lockstitch (301) should use 50 ply, all chainstitch (401) should use 50 ply for needle and 70 ply, and safety stitching (515 and 516) should use 50 ply for the looper, overedging (503 and 504) should use 70 ply, and safety stitching (515 and 516) should use 50 ply for the needle thread and 70 ply for other threads.

* Zipper: A brass Talon #42 zipper or equal is required. Zipper with brass teeth and slider-ratcheting-auto lock slider. Concealed zipper tape should be blended polyester/cotton or nylon/cotton.

General Instructions

* Cutting: Fronts, backs, sleeves, pockets and flaps should be cut lengthwise in goods. Collars and cuffs should be cut in the filling direction.

* Stitching: All joining seams, including sideseams, shoulder join, sleeve join, and bottom band should be

12-12 gauge (515 or 516) safety stitched.

Detail Design Characteristics

* Collar: Collar should be two-piece convertible style. Collar should have an interlining compatible with permanent press finish. Collar should be stitched, topstitched ¼ gauge and restitched to garment during attaching operation with 301 stitch type. Collar points should be 3” long, and collar should measure 2 ¾” at center back.

* Front: Closure: Zipper tape should be sandwiched between front and facing, attached with single needle 30 stitch, color to match self material. There should be 3/8” topstitching along the zipper.

* Inside Zipper Track: The jacket should be manufactured with an inside zipper track to accommodate zip-in/out liner with long sleeves.

* Facing: The jackets should have an approximate 3” inside facing which should be bound with 3/8” acetate or nylon tape. Along the facing edge, the zipper tape should be attached. The size and teeth of this zipper should be of such construction as to allow it to be joined with a zip-in/out liner. Facing and zip-in liner should be joined to zipper tape with 1 row of ¼” gauge 301 stitching.

* Pocket Flaps: Each flap should have 2 needle, ¼” gauge topstitching. Left flap should have a pencil division with each side of opening bartacked. Flaps should have straight side with single point at center.

Flaps should measure 6 3/8” wide, 1 5/8” at sides, and 2 ½” at center. Flaps should have buttonholes that are in alignment with buttons. Ends of flaps should be bartacked. Flaps should be attached with a 2 needle ¼” gauge.

* Pockets: Self material, attached with 2 rows, 1/4 gauge, 301 stitch. Both pockets should have a 27 ligne melamine button. Pocket size 6 ¾" wide by 6 ½” deep with mitered corners. Ends of pocket openings should be bartacked.

* Sleeves: One piece, coat style, set in sleeves, safety stitched, without vent.

* Cuffs: One piece design, clip corner, dress style, rectangular appearance, 2 " wide, and attached with 12-12 gauge (515 or 516) safety stitch. After joining cuff, turn seam allowance up and topstitch ¼” above joining seam. Each cuff should have one buttonhole with two 27 ligne melamine buttons on each cuff.

* Bottoms: Should finish with 2 ½” band. Jackets to have side knitted band, centered over side seam, 2 ½” high and 4” wide of 93% nylon/7% elastic double knit, 2 x 2 rib cardigan with color to match self material.

After joining band to main panels, the seam allowance should be folded up and caught by topstitching on outside of jacket ¼” above joining seam. The front waistbands should be topstitched at the bottom and each side.

* Patch: A National Park Service arrowhead shoulder patch shall be sewn securely in the center of the left sleeve with the top edge 1 ¾” to 2” below the shoulder seam depending on the garment size. The patch shall be sewn with inconspicuous stitching using brown thread closely matching the emblem background color.

Customization

* Badge Reinforcement: Badge tab should be constructed of self fabric, lined with 2 black metal eyelets 1” apart vertically from center to center and should be sewn ½” above left breast pocket flap. Finished tab should be 2” long and 1” wide.

Sizes: Regular XS-3XL Long M-3XL

Image shown is with badge tab and nameplate holder

UNIFORM COMPONENT SPECIFICATIONS (UNISEX)(Spec 007)

Gaiters

Expedition style gaiter that provides heavy-duty protection and insulation for extended mountaineering trips in harsh conditions.

Gender: Unisex

Performance/Work Environment Characteristics:

• Worn outdoors

• Waterproof and weather resistant (i.e., rain, snow, sleet)

• Gaiters shall be durable and last to industry standard

• Gaiters shall have a Gore-tex or equivalent lining membrane

Color Characteristics:

Forest Green

Sizes: Regular and X-Large

UNIFORM COMPONENT SPECIFICATIONS (UNISEX)(Spec 008)

Unisex Brass Belt Buckle (Replacement)

Sample Size: All dimensions are based on size 36.

GENERAL DESCRIPTION

Replacement brass belt buckle. Suitable for use on both the 9oz and 14oz (heavy-duty) embossed work belts.

Gender: Unisex

SALIENT CHARACTERISTICS

* Hardware: Two snaps, Rau manufacturer, No. 8020-F9, 8029-F10, 8031-F10, 8042-F10, or equal. Solid brass, polished gilt finish, 1-1/2” Waterbury buckle or equal.

Customization:

* Gold Plated

Stock Sizes: One Size

Metal Name Plate – SIGN LANGUAGE (UNISEX)(009) General Description:

The accessory is a metal name plate/bar with additional engraving used to identify the wearer as a Sign Language Interpreter.

Performance/Work Environment characteristics:

• worn with uniform in an indoor and outdoor environment

• must not tarnish

• clutch back or magnetic versions must be strong enough to remain attached to shirt in all work conditions

Color Characteristics:

• finish gold electroplate on brass metal

Style Characteristics:

• all metal, die struck nameplate

• magnetic and clutch back fasteners

• brass metal with gold electro-plate

• engraved individual name with color filled black

Custom Characteristics:

NPS – plain name bar with second line of engraving indicating the individual is a sign language interpreter

Size Characteristics:

• unisex

• 050 x ¾” x 3”

• polished edging 1/16”

Metal Name Plate – TWO LANGUAGE (UNISEX)(Spec 0010)

General Description:

The accessory is a metal name plate/bar with additional engraving used to identify the wearer as a Language (foreign language) Interpreter.

Performance/Work Environment characteristics:

• worn with uniform in an indoor and outdoor environment

• must not tarnish

• clutch back or magnetic versions must be strong enough to remain attached to shirt in all work conditions

Color Characteristics:

• finish gold electroplate on brass metal

Style Characteristics:

• all metal, die struck nameplate

• magnetic and clutch back fasteners

NPS – plain name bar with two additional lines of engraving. The additional lines of engraving shall be available in the following options, engraved in the native language:

1. I speak Spanish

2. I speak French

3. I speak German

4. I speak Chinese

5. I speak Japanese

Size Characteristics:

• unisex

Metal Name Plate – VOLUNTEER RECOGNITION (UNISEX)(0011) General Description:

The accessory is a metal name plate/bar with additional engraving used to identify the wearer as a V.I.P. Volunteer and identifying years of service.

Performance/Work Environment characteristics:

• worn with uniform in an indoor and outdoor environment

• must not tarnish

• clutch back or magnetic versions must be strong enough to remain attached to shirt in all work conditions

Color Characteristics:

• finish gold electroplate on brass metal

Style Characteristics:

• all metal, die struck nameplate

• magnetic and clutch back fasteners

NPS – plain name bar with additional engraving for years of service

Size Characteristics:

• unisex

UNIFORM COMPONENT SPECIFICATIONS (spec 0012)

Tie Tack

Sample Size: One size.

GENERAL DESCRIPTION

V. H. Blackinton style #A4270 design, arrowhead shape, 13/16" top to bottom and 11/16" side to side at widest point.Center to depict a giant sequoia tree, mountain, lake and bison raised from matt background with lettering "National Park Service" located in upper right portion of design.

SALIENT CHARACTERISTICS

* Basic Material: The material shall be a die struck, gold electroplated, 14 gauge (.064) brass.

General Instructions

* General: Border and center motif shall have polished highlights.

Detail Design Characteristics

* Attachment: F145 post, clutch chain and bar - V555, ½".

Quality Assurance:

* Production sample shall be approved by NPS COTR.

UNIFORM COMPONENT SPECIFICATIONS (Spec 0013)

Socks, Dark Brown, Mid-calf, Dress Crew (Dress Crew Sock)

Sample Size: Unisex two sizes 9-11 and 11-13.

GENERAL DESCRIPTION

Dress Crew sock with Thorlo-type padding.

Gender: Unisex

SALIENT CHARACTERISTICS

Components

* Basic Material: The basic material shall be 65% acrylic, 30% nylon, and

3% spandex or equal. The color shall be dark brown and shall match the standard sample.

Detail Design Characteristics

* Construction: The socks shall be constructed from a fine rib knit from the toe end to the ankle and from a medium knit from the ankle to the top of the sock. Designed to wick away perspiration.

Lengths: Relaxed Lengths 9- 11 11-13 Leg

Foot

Stretch Lengths 9- 11 11-13 Top Cross Leg Cross Foot Cross Foot Length

Sizes: S-2XL

UNIFORM COMPONENTS SPECIFICATIONS (Spec 0014)

Arrowhead Emblem

Gender: N/A

The emblem shall be arrowhead shaped and shall be sewn using three thread colors.

a. The thread must be a colorfast and must not fade crock, bleed, sublimate, or otherwise transfer or loose color and must be able to withstand commercial light color classification laundering and commercial dry-cleaning.

b. Stitch scale must be of sufficient density to preclude “bleeding” through of the background material color. There must be sufficient underlay stitching to give a full three-dimensional appearance to the design.

c. The Embroidery Colors are: Brown, Green, and White.

a. A plastic film or plasticized non-woven must be bonded to the reverse side of the emblem with sufficient heat and pressure to cause the film to melt and bond to the fabric and bobbin threads.

b. The backing must be applied in such a manner as to preclude crushing flattening or depressing of the embroidery, nor there be any jump or connecting stitch indentations or depressions in the embroidery caused by pressure during finishing.

c. The backing material must completely coat all raised elements on the back of the emblem and fill all depressions.

d. The finished emblem must be cut to the exact shape, size and geometry of the approved design.

b. The finished emblem must show a clear-cut execution and must be clean;

neatly made and with full tension on all threads.

c. The finished product must show no broken stitches, nor may any stitches be out of proper alignment.

d. Any repairs or mending must be done so that they do not affect the appearance or serviceability of the emblem.

f. The finished product must conform to the quality standard of this specification in all characteristics.

U. S. NATIONAL PARKS SERVICE

UNIFORM COMPONENT SPECIFICATIONS (0015)

LE Park Ranger Badge Emblem

The emblem shall be 2.375” X 3.375.”

Gender: N/A

SALIENT CHARACTERISTICS

Components

* Background Fabric: The twill background material must be first quality and cannot be mill seconds. The material must be a colorfast (able to withstand commercial light color classification laundering and commercial dry-cleaning) fine line twill six and one half to seven ounces per square yard, 100% polyester or cotton/polyester (50% or more polyester content) permanent press, cured and pre-shrunk (resin impregnated and oven cured). Component testing by a certified independent laboratory may be required.

a. Emblems must be machine embroidered on embroidery machines with numerical control devices. Embroidery done on Multi-head or Schiffli machines is allowed as long as the quality of the embroidery meets or exceeds the control samples.

b. Thread must be continuous filament bright 120/2 denier (or finer) polyester. Refer to the individual emblem illustrations for applicable thread size.

c. The thread must be a colorfast and must not fade crock, bleed, sublimate, or otherwise transfer or loose color and must be able to withstand commercial light color classification laundering and commercial dry-cleaning.

d. Stitch scale must be of sufficient density to preclude “bleeding” through of the background material color. There must be sufficient underlay stitching to give a full three-dimensional appearance to the design.

e. Double thread will not be permitted in any part of this emblem. Single thread stitching must be used throughout.

f. The minimum stitch count for this emblem is 4591 Multi-head Revolutions

g. The Embroidery Colors are: BROWN (PMS MATCH- 111)

* Overlock Border:

a. The top portion of the overlock border must consist of one end of 300 denier 4 ply polyester or two separate ends of 300 denier 2 ply polyester or five separate ends of 150 denier 2 ply rayon or 135 denier 2 ply polyester.

b. The bottom portion of the overlock border must consist of two separate ends of cotton or cotton polyester core wrapped thread in a matching color to the top portion of the overlock.

Clear monofilament is not permitted.

c. The overlock edge must be overrun a minimum of 3/8", and the end threads must be securely fastened to the back of the emblem or pulled through the entire length of the overrun. Neither method should affect the appearance of the emblem after attachment or make the emblem difficult to attach. Securing overrun with tape will not be permitted.

d. The manufacturer must certify that the overlock border will be applied in such a manner as to prevent it from pulling loose from the emblem, that it will be of a density sufficient to completely cover the fabric edge of the emblem, and that after proper attachment to a garment it will not curl after washing or dry cleaning.

a. A plastic film or plasticized non-woven must be bonded to the reverse side of the emblem with sufficient heat and pressure to cause the film to melt and bond to the fabric and bobbin threads. The film used must be able to withstand temperatures in excess of 300 degrees F in an alkaline solution and must be non-soluble in all commercial laundering fluids. Coating or film must NOT be chlorine retentive, nor should it emit toxic gases when subject to heat.

b. The backing must be applied in such a manner as to preclude crushing flattening or depressing of the embroidery, nor there be any jump or connecting stitch indentations or depressions in the embroidery caused by pressure during finishing.

c. The backing material must completely coat all raised elements on the back of the emblem and fill all depressions.

d. The finished emblem must be cut to the exact shape, size and geometry of the approved design.

b. The finished emblem must show a clear-cut execution and must be clean; neatly made and with full tension on all threads.

c. The finished product must show no broken stitches, nor may any stitches be out of proper alignment.

d. Any repairs or mending must be done so that they do not affect the appearance or serviceability of the emblem.

f. The finished product must conform to the quality standard of this specification in all characteristics.

UNIFORM COMPONENTS SPECIFICATIONS (0016)

Shoe Strings

General Description: Black Shoe strings. The shoe strings serve as replacement shoe strings for Men’s and Women’s Dress shoes.

Shoe strings shall be available to order in two sizes.

Vendor Style Description: Capps Shoes or equivalent

• Wax Coated

• 2 per package

Stock Sizes: 24 inches and 30 inches.

PROPOSED OPTIONS

LIFEGUARD UNIFORM

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

(Use Graphic 2)

Whistle + lanyard

Fox 40 Sonik Blast CMG, with Breakaway Lanyard, red (Item No.

9203–0208), or equal: Whistle with cushioned mouth grip (CMG); two chambers; four resonators; pea-less; with sound power that exceeds 120 decibels.

Red --- --- --- --- ---

Swimsuit (men)

Speedo Men’s Solid Dive Suit, Style No. 7300121 (red), or equal:

Men’s solid dive suit (red);

drawstring waist; fully lined;

reinforced seams; front gusset;

74% Antron Nylon / 26% Xtra Life Lycra® fiber.

Red 28–40 (even) Lettering and Logo

Placement:

Thigh, left

Swimsuit (women) – One-piece

Speedo Women’s One-Piece Solid Lycra® Flyback Swimsuit, Style No. 819006 (red), or equal:

Women’s solid one-piece swim-suit (red); with full lining (navy) both in front and in back; racer-style (flyback) back; bar-tack reinforcement at all stress points, such as under the arm openings and at crotch seams; inside seams shall have overlap stitching; outer edges shall be turned under and double-needle stitched through elastic; elastic shall measure at least ⅜ inch on all edges; 74% Nylon / 26% Xtra Life Lycra® fiber.

Red

Chest:

31”–39”

Waist:

23”–31”

Hips:

33½”–41½”

Lettering and

Chest, center

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Swimsuit (women) – Two-piece-A

Top: Speedo Women’s Solid Flyback Top – Separate, Style No.

719849 (red), or equal: Women’s solid bikini top (red); with full lining (navy) in front; racer-style (flyback) back; bar-tack rein-forcement at all stress points, such as under the arm openings;

inside seams shall have overlap stitching; outer edges shall be turned under and double-needle stitched through elastic; elastic shall measure at least ⅜ inch on all edges; elasticized band at base of top shall measure 1¼ inches on underside; 74% Nylon / 26% Xtra Life Lycra® fiber.

Red Chest:

31”–40½”

Lettering and

Chest, center

Swimsuit (women) – Two-piece-B

Bottom: Speedo Women’s Solid Bikini Bottom – Separate, Style No. 719852 (red), or equal:

Women’s solid bikini bottom (red); with full lining (navy) both in front and in back; ¼ inch webbed drawstring knotted at ends in waistband; bar-tack reinforcement at all stress points, such as at side seams of waistband, leg openings, and crotch; inside seams shall have overlap stitching; outer edges shall be turned under and double-needle stitched through elastic;

elastic shall measure at least ⅜ inch on all edges; 74% Nylon / 26% Xtra Life Lycra® fiber.

Red

Waist:

23”–32½”

Hips:

33½”–43”

NORTHEAST REGION

2015 – 2016

BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Board short (men)

Birdwell Beach Britches, Guard Britches 15 inches, Style No. 307 (red), or equal: Men’s board short (red); colorfast; 100% heavy nylon taffeta (double-ply); 15 inches in length, with side seams that end with 2-inch vents; nickel-plated grommets (¼ inch in diameter); white No. 24 Dacron thread stitching, or equal; seat seam, crotch seam, and all other inseams and outseams shall be full-fell seam construction, with 2 rows of ¼-inch gauge stitching;

woven nylon draw cord (3/16 inch).

Red 28–42 (odd / even)

Lettering and

Lower thigh, left

Board short (women)

Birdwell Beach Britches, Guard Britches 10½ inches, Style No.

302 (red), or equal: Women’s board short (red); colorfast; 100% heavy nylon taffeta (double-ply);

10½ inches in length, with side seams; nickel-plated grommets (¼ inch in diameter); white No. 24 Dacron thread stitching, or equal;

seat seam, crotch seam, and all other inseams and outseams shall be full-fell seam construc-tion, with 2 rows of ¼-inch gauge stitching; woven nylon draw cord (3/16 inch).

Red 1–12 (odd / even)

Lettering and

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Baseball cap (solid top)

Flexfit Tactel Cap, Style No. 6530 (red), or equal: Solid-top baseball cap (red); 6-panel;

profile fitted, with 3½-inch crown; Permacurv® visor, with silver underneath, and a front crown with fused buckram backing; 84% Nylon / 14% Cotton / 2% Spandex.

Red 6⅞”–7⅝” and

Crown, center

T-shirt (men) – short-sleeve

Champion Men’s 6.1-oz. Cotton Jersey T-shirt, Style No. CT–2226 (Oxford grey), or equal: Men’s 6.1-oz., cotton jersey T-shirt (Oxford grey); full athletic cut; ribbed crew neck; deep arm holes; extra-long body; hemmed sleeves and bottom; preshrunk; 90% cotton / 10% polyester.

Oxford Grey S–4XL

Lettering and

Pocket area, left

(No Logo)

Center, upper

T-shirt (men) – long-sleeve

Champion Men’s 6.1-oz. Cotton Jersey T-shirt, Style No. CH–2228 (Oxford grey), or equal: Men’s 6.1-oz., cotton jersey T-shirt (Oxford grey); full athletic cut; ribbed crew neck; deep arm holes; extra-long body; hemmed sleeves and bottom; preshrunk; 90% cotton / 10% polyester.

Grey M–2XL

Lettering and

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Broad-brim hat (floppy)

Original Watermen Canvas Tonga Hat, Style No. SKU: THC (Sand), or equal; Bucket-style hat (sand);

mesh eyelets; chin strap and cord lock; 4-in. crown; 3½-in. brim;

100% durable cotton canvas.

Sand One Size and

Crown, center

Hooded sweatshirt (no zipper)

Champion Men’s Reverse Weave, 14-oz., Hooded, Fleece Sweatshirt, No Zipper, Style No.

CS–2202 (Oxford grey), or equal:

Men’s very heavy (14-oz.), reverse-weave, fleece sweatshirt (Oxford grey); no zipper; full athletic cut; double-thick draw-string hood, with metal grommets; seamless shoulders;

long, set-in sleeves; muff pocket;

ribbed cuffs and waist-band; 80% Cotton / 20% Polyester Fleece.

Grey S–4XL

Lettering and

Sweat pant (closed bottom)

Champion Men’s Reverse Weave, 12-oz., Closed-Bottom, Sweat Pant, Style No. CP–1049 (Oxford grey), or equal: Men’s heavy (12-oz.), closed-bottom, reverse-weave, sweat pant (Oxford grey);

with tapered-leg cut; covered elastic waistband, with inside draw strings and large metal grommets; and covered elastic cuffs; 82% Cotton / 18% Polyester Fleece.

Oxford Grey S–3XL

Lettering and

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Wind-resistant jacket

Tri-Mountain Bay Watch Jacket, Style No. 3600 (red), or equal:

Hooded, hip-length jacket (red);

shell made of windproof / water-resistant, medium-weight, 100% Toughlan® nylon (or equal); with 9-oz. heavyweight cotton / polyester / rayon grey jersey lining; 3-piece cut hood; raglan sleeves; 2 exterior pockets with zippers, or with storm welts;

elastic cuffs and waist-band.

Red S–6XLT and

Left, pocket area

Rain jacket – (men)

Charles River Apparel New Englander Rain Jacket, Style No.

9199 (yellow 150 ), or equal: Shell:

100 % polyurethane; backing:

65% polyester / 35% cotton; body lining: 100% polyester; sleeve lining: 100% nylon. Additional features: Wind and waterproof with sealed seams; polyurethane bonded to a woven backing; lined with mesh for air flow circulation;

taffeta nylon in sleeves for easy on and off; hood and open hem with shock-cord drawstrings;

wind flap and heat-sealed seams throughout to seal out wind and rain; front-vented capes for breathability and easy decorating access; 2-way front zipper, offers freedom of movement; covered zippered side pockets; adjustable cuffs with hook and loop closure.

Yellow XS–5XL and

Left, pocket area

NORTHEAST REGION

NATIONAL PARK SERVICE

2015 – 2016

ITEM BRAND / FABRIC / QUALITY COLOR SIZE RANGE FRONT

(Use Graphic 1)

BACK

Rain jacket – (women)

Englander Rain Jacket, Style No.

5099 (yellow 154 ), or equal: Shell:

100 % polyurethane; backing:

65% polyester / 35% cotton; body lining: 100% polyester; sleeve lining: 100% nylon. Additional features: Wind and waterproof with sealed seams; polyurethane bonded to a woven backing; lined with mesh for air flow circulation;

taffeta nylon in sleeves for easy on and off; hood and open hem with shock-cord drawstrings;

wind flap and heat-sealed seams throughout to seal out wind and rain; front-vented capes for breathability and easy decorating access; 2-way front zipper offers freedom of movement; covered zippered side pockets; adjustable cuffs with hook and loop closure.

Yellow XS–3XL and

Rain pant – (unisex)

Englander Rain Pant, Style No.

9198 (true navy 260 ), or equal:

100% polyurethane bonded to woven backing; heat-sealed seams; generous cut to allow pant to be worn underneath;

pockets with snap closure, to allow for direct access to pants underneath; elasticized waist with shock-cord drawstring; adjust-able Velcro at hem of pant leg.

Navy XS–3XL and Logo

Front, left-thigh area --- ---

Revised by Carl Martinez 02–27–15 Prepared by Carl Martinez 01–29–15

Gateway National Recreation Area

UNIFORM COMPONENTS SPECIFICATIONS (UNISEX)(Spec 0034)

Brown Gore-Tex Hood

Brown Gore-Tex non-insulated detachable hood.

SALIENT CHARACTERISTICS

Components

* Basic Material: The fabric of the shell shall be 100% nylon Gore-Tex and the lining shall be

100% nylon.

* Seams: All seams shall be hot air sealed with Gore-Tex sealing tape on the inside.

* Snaps: The snaps shall be 24 ligne DTM that correspond to the snap locations on the jacket.

* Labels: See general reference and requirements sheet.

Detail Design Characteristics

* The hood shall be fully lined. The hood shall be two piece construction with a drawstring and snap front closures. The hood shall attach to the shell with four snaps. The front shall have a face opening of 27 ½” on a size large.

Sizes: S/M, L/XL, XXL/3XL

VOLUNTEER Hip Length Overshell Jacket with Detachable Hood (UNISEX)(Spec 0035)

The garment is a hip length overshell with a detachable non-insulated hood.

This overshell can be worn alone or the fleece jacket or the down parka can be zipped in as a liner.

This overshell shall have an inside zipper to allow for the fleece jacket (NPS VOLUNTEER Spec 0036) or the down parka (SHARED Spec 0035) be zipped in as a liner.

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• Worn as an outer layer in an outdoor work environment

• The fit shall be comfortable and allow for be full range of motion to including bending

• The garment shall be fully lined and uninsulated

• The garment shall have front storm flaps, a front two way zipper with outer snap closures and an adjustable waist cord

• The garment shall have adjustable side vents for radio and pants pocket access

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The front zippers shall be located mouth to mouth for two way movement and access up and down

• The vent zipper at side seam shall allow access to radio or other items on belt

• The hood shall be detachable

• The fabric shall be GORE-TEX or equivalent

• Dark Brown – NPS

STYLE CHARACTERISTICS

• Drawstring: Concealed drawstring tunnel at the waistline, beginning and ending at the zipper tape/weather flap seams.

• Pockets: Should have hand-warmer slash pockets on the front, at minimum one zippered patch pocket inside the breast and pockets in the side seams with secure closures

• Side Vents: Should be closed with an inseam zipper

• Zippers: Shall have double sliders with long tabs and storm flaps

• Sleeves: Should be fully lined with a mechanism for adjustable closing at the wrist cuff

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Hood: Lined, non-insulated matching fabric with visor, drawstring front closure with cord locks and snap front closure, and snap attachments to matching placement on overshell

• Part of integrated outwear system (waist length overshell, fleece jacket and down parka)

CUSTOMIZATION

No patches/emblems/badges No badge tabs or name plates The detachable hood is sold separately

SIZE CHARACTERISTICS

Stock: XS – 3XL

Non-stock: XXS, 4XL, 5XL

NPS – VOLUNTEER Hip Length Shell (System)

VOLUNTEER Fleece Jacket/Liner (UNISEX)(Spec 0036)

The garment is a fleece-lined jacket/liner. The fleece jacket is part of an integrated outerwear system that also includes a a hip-length overshell jacket and a down parka.

The fleece-lined jacket/liner can be worn alone, or it can be zipped into the VOLUNTEER hip-length overshell (NPS VOLUNTEER Spec 0036).

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• Worn as an outer layer in an outdoor work environment

• Worn as a layer under/within other jackets in the integrated system.

• The fit shall be comfortable and allow for be full range of motion to including bending

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• Brown – NPS

STYLE CHARACTERISTICS

• Pockets: Should have two front slash pockets, lined and with secure closures

• Sleeves: Should have a knit cuff at the wrist

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Bottom: Should be a snug fit knitted waistband

• Zipper: The front zipper shall extend from bottom hem up thru collar

CUSTOMIZATION

No patches/emblems/badges No badge tabs or name plates

SIZE CHARACTERISTICS

Stock: XS – 3XL

Non-stock: XXS, 4XL, 5XL

NPS – Fleece Jacket

USACE– Fleece Jacket

FWS - Fleece Jacket

BLM - Fleece Jacket

F LS Grey 100C Work Shirt

Gender: Female

The garment is form fitting with two pleated breast pockets with scalloped flaps and shoulder straps. The shirt has military creases, a pencil slot, and a shoulder emblem. Variations of this garment shall include male and female.

Sample Size: All measurements are based on a sample size 36.

Components

* Basic Material: The material shall be 100% Cotton. The color shall be Grey.

* Linings: Shall have collar and yoke linings that are compatible with the construction of the shirts.

* Thread: Sewing thread for all operations shall be cotton covered polyester, dyed to match shade of self material, and conforming to ticket numbers 50-2 ply or 50-3 ply.

* Buttons: Buttons shall be first grade 19 ligne pearlescent plastic buttons and shall match the color of basic material.

* Collar Stays: The collar stay shall be made of good quality vinyl, attached to the inside of the bottom collar leaf, and come out to the stitching line.

General Instructions

* Cutting: Collars, bands, pockets, and flaps shall be cut to ensure uniformity.

* Stitching: A lockstitch (301) shall be used throughout, except inserting the sleeve and side closing operations, which shall be safety stitched (516). All topstitching shall be ¼” from edge. There shall be 10 to 14 stitches per inch required.

* Button Holes for Two-Piece Shirt Collar: The shirt shall have 6 cut buttonholes down the front. The center of the first buttonhole shall be placed on the collar band 1” from edge. The center of the second buttonhole which is on the center plait shall be 3 ¼” from the bottom of the collar. For proper appearance with clip-on tie, the stand shall be fastened with one button so there shall be a tie space of ¼” when collar is buttoned. The remaining buttonholes shall be spaced 3 ½” apart. There shall be 1 cut buttonhole on each shoulder strap and 1 uncut buttonhole on each pocket flap.

* Two-Piece Shirt Collar: The garment shall have a two piece shirt collar. The points on the collar leaf shall measure 2 7/8” in length and be topstitched ¼” from the edge. The collar leaf shall be 1 ½” from roll line to bottom edge of collar at center back. The collar stand shall measure 1 5/16” at center back and be topstitched 1/16” from top and bottom edges. For proper appearance with clip on tie, the stand shall be fastened with one button so that there shall be a tie space of ¼” when the collar is buttoned. The collar’s interlining shall be a permanent press finish of 250 weight or equal.

* Shoulder Straps: Shoulder straps shall be 1 5/8” at sleeve head and tapered to 1 3/8”-1

¼”. The straps shall be stitched to the shoulder by a single needle machine forming an "X" beginning at the sleeve head and extending for approximately one-half the length of the strap. Length of straps shall be graduated conforming to size of shirt and set not more than ½” from folded collar. Buttons attached to yokes shall match shoulder strap buttonholes at pointed ends. The shoulder straps shall be sewn down around the edges.

* Front for Two-Piece Shirt Collar: Each front shall have a facing 2 ½” in width extending from the neckline to the bottom of the shirt, and provided by a turn under of material. The right front shall contain 6 vertical buttonholes placed ¾” from the edge of the plait and be 3 ½” apart. There shall be one button on the collar stand placed ¾” from edge. The button stand shall be 7/8” wide and be placed on the right side of the shirt.

The buttons shall be securely attached to the button stand corresponding to the buttonholes on the facing.

* Pocket Flaps: There shall be two deep scalloped flaps, 5 7/8” wide, 2 ¼” at sides, and 2

¾” at center. There shall be a 1 ½” pencil opening through the left flap and a vertical uncut buttonhole in the center of the flap with a button sewn on top of the buttonhole.

The flaps shall be topstitched 1/8” from edge and attached to the shirt front with a double row, ¼” gauge stitching. The underside of the flap shall have hook and pile tape, approximately 1” long by 3/8” wide, positioned on outer points of both pocket flaps.

* Pockets: Both pockets shall have 1 ½” centered pleats stitched to prevent spreading.

Pockets shall be 5 ½” wide x 5 ¾” deep with bottom mitered corners. The left pocket shall have a pencil slot 1 ½” from center edge. Upper hem shall be ½” wide. Pockets shall be topstitched 1/16” gauge with ¾” triangle tacks at upper corners. Both pockets shall have an approximately 1” long by 3/8” wide piece of hook and pile tape positioned to correspond with the hook and pile tape on each outer scalloped flap point.

* Yoke & Back: The yoke shall be constructed of two pieces. The outside yoke shall be made of the same fabric as the outer shell of the garment and the inside yoke shall be made of the lining fabric. The yoke shall be 3 ½” at center back and 3 ¾” at armhole.

* Long Sleeves: Each sleeve shall have a 5” long sleeve placket with a 1” wide top placket and a ½” wide bottom placket. The sleeve is 5” long with top and bottom facings.

A vertical buttonhole shall be sewn 2 ½” from top of cuff centered on top placket with matching button centered on bottom.

* Cuffs: Cuffs shall be 2 ½” in depth with rounded corners ¼” topstitching at bottom and double stitched 3/8” gauge topstitching where cuff joins sleeve. Two horizontal buttons with corresponding horizontal buttonhole shall be centered on each cuff 1” apart.

* Bottoms: A ¼” rolled hem at the bottom of the garment is preferred.

* Customization: The organizations shoulder patch shall be sewn securely in the center of the left sleeve with the top edge 1 ¼ to 1 ½” below the shoulder seam depending on the garment size. The patch shall be sewn with matching thread and attached so that the edges do not roll-up after washing.

Sizes: Bust Size Sleeve 28 30 R 30 30 R&L 32 30 R&L 34 30 R&L 36 31 R&L 38 31 R&L 40 32 R&L 42 33 R&L 44 33 R&L 46 33 R&L 48 33 R&L 50 33 R&L

Longs – Add 1” to Sleeve length

F SS Grey 100C Work Shirt

Gender: Female

The garment is form fitting with two pleated breast pockets with scalloped flaps and shoulder

Sample Size: All measurements are based on a sample size Female-36.

Components

* Basic Material: The material shall be 100% Cotton. The color shall be Grey.

* Linings: Shall have collar and yoke linings that are compatible with the construction of the shirts.

* Thread: Sewing thread for all operations shall be cotton covered polyester, dyed to match shade of self material, and conforming to ticket numbers 50-2 ply or 50-3 ply.

* Buttons: Buttons shall be first grade 19 ligne pearlescent plastic buttons and shall match the color of basic material.

* Collar Stays: The collar stay shall be made of good quality vinyl, attached to the inside of the bottom collar leaf, and come out to the stitching line.

General Instructions

* Cutting: Collars, bands, pockets, and flaps shall be cut to ensure uniformity.

* Stitching: A lockstitch (301) shall be used throughout, except inserting the sleeve and

* Button Holes For Convertible Collar: The shirt shall have 6 cut buttonholes down the front right facing. The center of the first buttonhole shall be ½” from top edge at center front. The center of the second buttonhole on the right facing shall be 2 ½” from the bottom of the top buttonhole. The remaining buttonholes shall be spaced 3 ½” apart.

There shall be 1 cut buttonhole on each shoulder strap and 1 uncut buttonhole on each pocket flap.

* Convertible Collar: The garment shall have a one-piece convertible collar. The points on the collar shall measure 2 7/8” in length, 2 7/8” at center back, and be topstitched ¼” from the edge. The collar’s interlining shall be a permanent press finish of 250 weight or

* Shoulder Straps: Shoulder straps shall be 1 5/8” at sleeve head and tapered to 1 3/8”-1

¼”. The straps shall be stitched to the shoulder by a single needle machine forming an "X" beginning at the sleeve head and extending for approximately one-half the length of the strap.