State_of_Work_for_FY19_Guam_Groton_Tech_Refresh_Finalized_as_1-29-2019.docx

09 Jan 19

Task Statement (FY-19) for Legacy MRTS 21H42 GROTON TOUCH SCREEN TECH REFRESH

1. Purpose: This Task Statement covers three tasks.

A. The contractor shall perform a technical refresh by replacing existing trainer pole mounts with government provided 19” computer racks, installing existing computers, wiring, and new touchscreens on the Multipurpose Reconfigurable Training System (MRTS) Submarine Radio 21H42 trainer at Naval Submarine School (NSS), Groton, CT.

B. The contractor shall perform a technical refresh by installing new touchscreens on the MRTS Submarine Radio 21H45 trainer at NSS, Groton, CT.

C. The contractor shall perform a technical refresh by installing new touchscreens on the MRTS Submarine Radio 21H42 trainer at Submarine Learning Center (SLC) Detachment Guam, Marianas.

2. Scope of Effort: The following tasks will follow these requirements:

a. CLIN 001: Legacy MRTS 21H42 Tech Refresh NSS, Groton, CT

(1) Contractor will provide their own tools for the work outlined in this task.

(2) Remove computers, displays, UPS’s, audio cards, network switches, USB hubs, intercom system, microphone clip, handset cradle and associated cables from existing trainer pole mounted carts in accordance with local instructions.

(3) Remove existing trainer pole mounted carts, equipment rack and relocate them to another location on the naval base and package them for shipment to NAWCTSD Orlando, FL.

(4) Relocate the 30” displays to another location on the naval base and package 80% of them for shipment to various other MRTS sites.

(5) Install the provided computer racks in locations identified in MRTS Radio Room Layout drawing for Refresh NSS, Groton, CT. Once racks are leveled, racks should be bolted together.

(6) Install Audio Panel and wiring previously removed from the pole mounted system as shown in Photo 2 Audio Panel.

(7) Assemble racks in accordance with Refresh Procedure with 40” Monitors Version 1.0.

(8) Contractor shall install and connect the 40” touchscreens into the computer racks.

(9) Install existing computers and cables into new computer racks reconnecting all computer cables and audio cables.

(10) Install network switches into racks designated Column 1 and Column 7. Run network cables from switches to all computers, equipment rack connectors, and the printer.

(11) Install UPS’s to bottom of rack.

(12) Install USB hubs, intercom system, microphone clip, and handset cradle into new computer racks.

(13) Contractor shall test installed hardware to verify computers, touch screens, network switches and network cables are installed and are functioning correctly. Simulation software testing will not be required.

(14) Contractor shall remove and dispose all packing materials and disposed of as outlined in local instructions.

(15) Contractor shall move 48” custom maintenance rack shipped from Orlando with the installed parts to the MRTS 21H44 Room on the same floor as the MRTS 21H42.

(16) Contractor shall install three computers, 42” display, two 20” displays, three UPS’s and associated wiring shipped with the cabinet, back into the cabinet.

(17) Contractor shall test installed maintenance rack hardware to verify computers, touch screens, and network cables are installed and are functioning correctly. Simulation software testing will not be required.

b. CLIN 002: Legacy MRTS 21H45 Tech Refresh NSS, Groton, CT

(1) Contractor will provide their own tools for the work outlined in this task.

(2) Purchase touchscreens and rack mounts to be delivered to NSS, Groton, CT building 533 room 503 in accordance with this task statement. Drivers of the truck deliveries must have access to the naval base. Trucks delivering material must have a lift gate as access to a loading dock may not be possible.

(3) Remove old screens on Device 21H45 in NSS, Groton, CT and relocate them for DRMO disposal in accordance with local instructions.

(4) Contractor shall install and connect the new touchscreens and rack mounts to the existing 21H45’s computers. The I-TECH 42” touch screen will require new mounting holes to be drilled in the appropriate locations on the mounting panel.

(5) Install USB hubs, intercom system, microphone clip, and handset cradle into new computer racks.

(6) Contractor shall test installed hardware.

(7) Contractor shall remove and dispose all packing materials in accordance with local instructions.

c. CLIN 003: Legacy MRTS 21H42 Tech Refresh SLC Detachment Guam, Marianas

(1) Contractor will provide their own tools for the work outlined in this task.

(2) Purchase touchscreens and rack mounts to be delivered to SLC Detachment Guam building 4470 room 117 in accordance with this task statement. Drivers of the truck deliveries must have access to the naval base. Trucks delivering material must have a lift gate as access to a loading dock may not be possible.

(3) Remove old screens on Device 21H42 in SLC Detachment Guam and relocate and palletize them for DRMO disposal in accordance with local instructions.

(4) Relocate the displays to another location on the naval base and package of them for shipment to NAWCTSD Orlando.

(5) Install USB hubs, intercom system, microphone clip, and handset cradle into new computer racks.

(6) Contractor shall test installed hardware.

(7) Contractor shall remove and dispose all packing materials in accordance with local instructions.

3. Period of Performance: Based on the scope of effort, the Period of Performance (PoP) for delivery for Tasks (a), (b), and (c) are to be completed NLT 180 calendar days after contract award.

4. Deliverables to the Government:

a. All Commercial off the shelf (COTS) documents shall be delivered to the government.

Final delivery of COTS documents may be on electronic format.

5. Contract Vehicle:

6. Hardware Information:

Table 1: Installation Sites & Touchscreen Configurations per site

Touch-screens Number of 21" Touch-screens Number of 42" Touch-screens

Table 2: Parts list for CLIN 001 Groton, CT. (Material is not to be purchased, will be provided onsite.)

Table 3: Parts list for CLIN 002 Groton, CT.

Table 4: Parts list for CLIN 003 Guam, Marianas.

a. Specifications for 40” Touchscreens:

TP400DO TekPanel 40" TFT-LCD touchscreen 3840 x 2160 Resolution 350 nits Brightness 5000:1 Contrast Ratio Response Time: Gray to Gray 8.5ms Hertz: 50/60Hz frame rate Viewing Angle: 176/176 degrees Bezel opening: 881.11mm x 488.35mm Custom Enclosure & Bezel - Thin Aluminum, Matte Black Touch Screen: Glass Laminate PCAP - 10-point multitouch I/O Package: Display Port / HDMI Buttons located on back of panel per NAVY Spec Speakers: NONE REQUIRED Warranty: 1 Year Standard Mount: VESA centerline mounting penetrations per NAVY Spec Portrait/Landscape Modes

b. Specifications for 40” touchscreen mounting brackets for standard 19” racks:

Monitor Mount Bracket – SFI P/N: 21512FO12100

c. Specifications for Server Display:

Diagonal Viewing Size:

48.0 cm

19.0 Inches

Preset Display Area (H x V):

374.78 mm x 299.83 mm 14.76" x 11.80" 112370 mm² (174.17 inches²)

Aspect Ratio:

(5:4)

Backlight Technology:

LED

Display Screen Coating:

Antiglare with 3H hardness

Panel Type:

In-Plane switching Technology

Maximum Preset Resolution:

1280 1024 at 60Hz

Viewing Angle:

(178° vertical / 178° horizontal)

Contrast Ratio:

1000: 1 (typical) 4 Million: 1 (Dynamic)

Pixel Pitch:

0.293 mm x 0.293 mm

Pixel Per Inch (PPI):

Brightness:

250 cd/m² (typical)

Response Time:

6 ms (gray to gray - fast mode) 8 ms (gray to gray -normal mode)

Wireless Charging Feature:

NA

G-SYNC Support:

NA

PbP / PiP:

PbP (No) PiP (No)

Daisy Chain Availability:

No

Dell Display Manager Compatibility:

Yes

Remote Asset Management:

Yes, via Dell Command |Monitor

Color Support:

Color Gamut (typical): 84% (CIE 1976), 72% (CIE 1931) Color Depth: 16.7 Million colors

Color Calibration SDK SW:

No

Color Calibration with X-rite colorimeter:

No

Connectivity 1 x DP (ver 1.2) 1 x HDMI (ver 1.4) 1 x VGA 1 x USB 3.0 port - Upstream 2 x USB 3.0 ports - Side 2 x USB 2.0 ports - Bottom

Built-in Devices:

USB3.0 super-Speed Hub (with 1 x USB upstream port, 2 x USB3.0 and 2 x USB2.0 downstream ports)

Security Security lock slot (cable lock sold separately) Anti-theft stand lock slot (to panel)

Dimensions Height with stand (Compressed ~ Extended):

369.3mm ~ 499.3 mm 14.54" ~19.66"

Width:

405.6mm 15.97"

Depth:

180.0mm

7.09 inches

Height without stand:

334.3mm 13.16"

Width without stand:

405.6 mm 15.97"

Depth without stand:

50.3mm 1.98"

Weight (panel only - for VESA mount):

2.60 kg

5.73 lb

Weight (with packaging):

6.61 kg

14.57 lb

Adjustability:

Height-adjustable stand (130mm) Tilt (-5° to 21°) Swivel (45° to 45°) Pivot (90° clockwise) Built in cable-management

Flat Panel Mount Interface:

VESA (100 mm)

Power Voltage Required:

100 to 240 VAC / 50 or 60 Hz ± 3Hz / 1.5 A (typical)

Power Consumption (Operational):

14W (typical) /38W (maximum)**/44.3 kWh (Energy Star)

Power Consumption Standby / Sleep:

Less than 0.3W

Environmental Temperature Range:

Operating: 0° to 40°C (32° to 104°F) Non-operating: -20° to 60° (-4° to 140° F)

Humidity Range:

Operating: 10% to 80% (non-condensing) Non-Operating:5% to 90% (non-condensing)

Altitude:

Operating: 5,000 m (16,400 ft) max Non-Operating: 12,191 m (40,000 ft) max

Warranty 3 Year Advanced Exchange Service and Premium Panel Guarantee

Regulatory

ENERGY STAR

EPEAT Gold TCO Certified Displays RoHS Compliant

Monitor with stand Power cable 1 x DP Cable 1 x VGA Cable 1 x USB 3.0 upstream cable (enables the USB port on the monitor) Drivers and documentation media Quick setup guide Safety Information

d. Specifications for 42” touchscreen:

I-Tech Company 42" Touchscreen with IR Touch P/N: BCHW4200-MOT

Touchscreen Details LCD Technology SPVA (super pattern vertical align) Display Colors 1.07 billion Pixel Pitch 0.485 x 0.485 mm Brightness 700 cd/m2 (nit) typical with touch sensor (max.)(1) 610 cd/m2 (nit) typical Contrast Ratio (2) 4000:1 typical Viewing Angle Horizontal/Vertical: 178 degrees typical Video Response Time (3) 8 ms typical Refresh Rate 60Hz Control Type OSD Native Resolution 1920 x 1080

(1) Brightness measured on a display with 3M™ Projected Capacitive sensor. (2) Measured at a contrast ratio of 10. (3) Gray to Gray Touch Details Number of Touch Points 60 points with palm rejection Touch Point Speed (4) <12 milliseconds Input Type Finger, thin glove Touch Communication USB Operating System Support Windows 8 / 7/ Vista / XP, Linux, Mac

(4) up to 20 touches Physical Specifications Product Details Operating Environment 0 to +40 degrees C, relative humidity, non-condensing 90% Storage Environment -10 to +60 degrees C Video Input DVI, VGA, HDMI, DP (HDCP) Audio Speaker: 5W + 5W @ 8Ω Headphone: 20mW + 20mW @ 32Ω Cover Glass Chemically-strengthened VESA Pattern 400mm x 400mm Power Supply Internal 110/220 VAC Power Supply Power Consumption 100W Typical, 130W Max RoHS Compliant Yes Agency Approvals FCC-B, CE, TUV (IEC 60950), C-TICK Warranty 2 years Dimensions and Weight Display Area (WxH) 930.24 x 523.26 mm (viewing area) 36.62 x 20.60 inches Display Dimensions 993.5 x 585.5 x 66.4 mm (outer) 39.11 x 23.05 x 2.61 inches Packaging (WxHxD) 1095 x 700 x 192 mm 43.11 x 27.56 x 7.56 inches Packaging/Display weight 26kg / 57.3lbs Touchscreen weight 23kg / 50.7lbs

e. Specifications for 20.1” touchscreens:

I-Tech Company 20.1" Monitor with Surface Capacitive Touch P/N: ERM2010B TC-3M-NV01

4:3 aspect ratio 1600x1200 resolution

19” rack mounting kit

7. Photos

Photo 1 Rack Bottom

Photo 2 Audio Panel

Photo 3 21H42 Groton

Photo 4 21H42 Groton

DISTRIBUTION STATEMENT C - Distribution authorized to U.S. Government agencies and their contractors for use on government contracts only (11 November, 2014). Other requests for this document shall be referred to NAWCTSD Undersea Department.

image3.jpg image4.jpeg image1.jpg image2.jpg