N4008519B0095 Drawings_Part8.pdf

The Walker Group Architecture, Inc PO Box 541, New Bern, NC 28563

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

ROAD SIDE

DIRECTION

OF TRAFFIC

ADDITIONAL

GROUND RODS

(WHEN REQUIRED)

PLAN

ALWAYS CONNECT THE POLE GROUND

LEAD(S) DIRECTLY TO THE NEUTRAL-

ENSURE THAT THE COPPER CONDUCTOR

WILL ALWAYS BE BELOW THE ALUMINUM.

CONNECTOR

NEUTRAL COPPERWELD STAPLES (TYP.)

GROUND

WIRE

POLE

ELEVATION

GROUND ROD

PLASTIC OR FIBER MOLDING

GALVANIZED STAPLES (TYPICAL)

FINISHED

GRADE

#4 BARE

COPPER

POLE

OH-41JUNE 2002SKETCH DATE STYLE

GROUND

24"

MIN.

10'-0"

MIN.

10'-0"

MIN.

24"

12"

8'-0"

MIN.

18"

MAX.

8'-0 MIN.

(FROM 24'-4"

TO 16'-4"

ABOVE GRADE)

ALTERNATE GROUND WIRE

POSITION. (USE WHEN

MULTIPLE GROUNDING

SYSTEMS ARE REQUIRED.)

(SEE NOTE 4)

1.

2.

3.

NOTES

USE ADDITIONAL GROUND RODS, WHEN REQUIRED,

TO OBTAIN RESISTANCE VALUE, AS REQUIRED BY

IEEE C2.

MAKE GROUNDING CONNECTIONS TO ALL EQUIPMENT

ON POLE AS REQUIRED BY IEEE C2.

FOR SYSTEMS OTHER THAN 4 WIRE, MULTI-

GROUNDED, USE SEPARATE GROUNDING

CONDUCTORS AND ELECTRODES FOR PRIMARY

AND SECONDARY SYSTEM DEVICE CONNECTIONS.

#4 600V INSULATED COPPER GROUNDING

CONDUCTOR REQUIRED ON PRIMARY SYSTEM

WHEN SEPARATE SYSTEMS ARE REQUIRED.

4.

AF-1APRIL 2015

GENERAL ARC FLASH WARNING LABEL

SKETCH DATE STYLE

NOTES:

1. PROVIDE SELF-ADHESIVE VINYL LABEL TO AFFIX TO ELECTRICAL EQUIPMENT TO WARN OF ARC

FLASH HAZARDS.

2. THE LABEL FORMAT AND TEXT SHALL BE IN ACCORDANCE WITH THE FIGURE.

3. THE LABEL SHALL BE LOCATED ON THE EQUIPMENT TO BE CLEARLY VISIBLE TO QUALIFIED

PERSONS BEFORE EXAMINATION, ADJUSTMENT, SERVICING, OR MAINTENANCE OF THE

EQUIPMENT.

4. THE SIZE OF THE LABEL SHALL BE MINIMUM:

EQUIPMENT TYPE HEIGHT WIDTH

INDOOR 2" 3"

OUTDOOR 3" 4.5"

5. A DOWNLOADABLE WINDOWS METAFILE IS AVAILABLE ON THE WHOLE BUILDING DESIGN GUIDE

WEBSITE (WWW.WDBG.ORG) FOR USE IN A LABEL MAKING MACHINE.

A. THE FILE IS LOCATED ON THE "NAVFAC CADD DETAILS" PAGE. TO NAVIGATE TO THIS

LOCATION, FOLLOW: HOME > DOCUMENTS & REFERENCES > CCB > CADD LIBRARY >

NAVFAC CADD RESOURCES > NAVFAC CADD DETAILS.

B. ALTERNATIVELY, TYPE IN THE FOLLOWING ADDRESS IN INTERNET EXPLORER:

HTTP://WWW.WBDG.ORG/CCB/BROWSE_CAT.PHP?C=232

WIDTH

HEIGHT

(SEE NOTE 1)

SERVICE CAP

CLAMP TYPE

SE

CO

ND

AR

Y

CO

ND

UC

TO

R

NE

UT

RA

L

OR

T

OP

GRADE

FINISHED

GALVANIZED STEEL CONDUIT-SIZE AS INDICATED

SEE NOTE 3

SEE NOTE 2

CONDUIT LOCATION

OF TRAFFIC

DIRECTION

ROAD SIDE

POSITION

RISER

ALTERNATEPOSITION

RISER

POLE

1.

2.

3.

DIRECT BURIED

CABLE

DIRECT BURIED

CONDUIT

TYPE C

OH-35JUNE 2002

(SIZE & TYPE AS INDICATED)

CONDUIT RISER

SKETCH DATE STYLE

TYPE A

CONCRETE ENCASED

CONDUIT

TYPE B

18" MIN.

2"

MIN.

NOTES

ON CONDUIT RISER FOR PRIMARY CIRCUITS, ELIMINATE SERVICE CAP

AND PROVIDE GROUNDING TYPE INSULATING BUSHING.

BOND CONDUIT TO POLE GROUND AND SYSTEM NEUTRAL (IF EXISTING).

SEE GROUNDING NOTES ON SKETCH OH-41.

SPACE STRAPS AT MAXIMUM OF 4' INTERVALS.

1'-6" O.C.

3" MINIMUM

FINISHED GRADE

DUCTBANK MARKING TAPE

3000 P.S.I. CONCRETE

P.V.C. CONDUIT SIZE

AS INDICATED

LEVELING BLOCKS

AT BASE SPACERS

" M

IN

.EQUAL

EQUAL

3" MINIMUM

SEPARATION

(TYP.)

BASE SPACERS

(TYP.)

NOTE: # OF DUCTS SHALL BE AS INDICATED ON PLANS.

3"

SECONDARY

TRANSFORMER BOX

GRADE

TERMINATIONS

LOW VOLTAGE CABLE

CURRENT TRANSFORMERS (800/5)

3-POLE FUSE BLOCK

SECONDARY CIRCUIT

WHD

#4/0 BARE

MIN

2'-0"

GRADE.

PAD. MIN 18" BELOW FINISHED

ENCIRCLING ENTIRE CONCRETE

#4/0 BARE COPPER GROUND LOOP

600V INSULATION

CORNER OF PAD.

OF 4, 1 AT EACH

GROUND ROD, TYP

GROUND PAD (TYP OF 2)

#4/0, 600V

INSULATIONPRIMARY CIRCUIT

CONNECTOR

LOAD BREAK

PRIMARY NEUTRAL

BUSHING INSERT

BREAK OIL SWITCH

2 POSITION LOAD

CURRENT-LIMITING

OIL-IMMERSED

PRIMARY COMPARTMENT

ARRESTERS

SURGE

TRANSFORMER

BUSHING WELL

X0

BAYONET OIL-IMMERSED

EXPULSION FUSES

FUSES

CABLE WELL

TRANSFORMER BOX, SEE DETAIL THIS SHEET.

G

G

G

G GROUND ROD - 3/4" x 10' CONNECT

TO CONDUCTORS BY EXOTHERMIC

WELD (TYP)

PAD MOUNTED COMPARTMENTAL TYPE

TRANSFORMER (SECURE TO TRANSFORMER

BOX PER MANUFACTURER'S

RECOMMENDATION).

SECONDARY NEUTRAL GROUND NO.

4/0 AWG CU MINIMUM

TRANSFORMER

SECTION

EXOTHERMIC WELD (TYP)

EQUIPMENT GROUND

OUTGOING SECONDARY CONDUIT(S)

(NUMBER AS NOTED ON PLANS)

PRIMARY CONDUIT

NUMBER AS NOTED ON

PLANS

EXTEND GRAVEL FILL A

MINIMUM OF ONE FOOT

BEYOND PAD ON ALL SIDES.

WELL COMPACTED GRAVEL

SUBSURFACE SHALL BE 6

INCHES THICK

EXTEND PAD A MINIMUM OF 8

INCHES BEYOND UNIT ON ALL

SIDES

PAD MOUNTED TRANSFORMER DETAIL

NOT TO SCALE

TYPICAL PAD MOUNTED COMPARTMENTAL TRANSFORMER DETAIL

NOT TO SCALE

COMPARTMENT

X10" 10"

6"

9" 18"2-1/2"18"

29"

29"

5"

18"

TRANSFORMER BOX DETAIL

(DETAIL BASED ON PARKING BUMPER COMAPNY STANDARD DETAILS)

CONCRETE ENCASED DUCTBANK - DETAIL 'A'

NOT TO SCALE

CONNECTOR

LOOP FEED

WATTHOUR DEMAND METER: TO

CONFORM TO BASE

STANDARDS. ITRON V&I CS3

SERIES METER.

PRIMARY

JUNCTION

ENCLOSURE

CONCRETE

14"

14"

PLAN

SIDE ELEVATION

FRONT ELEVATION

DEAD FRONT MODULE

'U' STRAPS SUPPLIED WITH

MODULE.

MOUNT 'U' STRAPS CLAMPS (6)

SUPPLIED WITH ENCLOSURE) OVER 'U'

STRAPS TO SECURE TO MODULE.

DEAD FRONT BUSHING WELL

INSERT CONNECTOR.

UNDERGROUND

PRIMARY CONDUIT

UNDERGROUND

PRIMARY CONDUIT

PRIMARY CABLES

FINISHED GRADE

CONCRETE

18"

23"

62"

DEAD FRONT PARKING

STAND

DEAD FRONT MODULE

GROUND LUG (TYPICAL OF

3)

CONCRETE

GRADE

TOP IN OPENED

POSITION.

LIFTING LUGS

(TYPICAL FOR 4)GROUND LINE, DO NOT FILL

INTERIOR OF ENCLOSURE.

46-1/4" 3"

32"

41"

THREE PHASE, FULLY DEAD FRONT, 2-WAY SECTIONALIZING PEDESTAL WITH

15KV, 600 AMP RATINGS. PROVIDE INDUSTRY STANDARD DEAD FRONT

JUNCTION MODULES AND ELBOWS CONFORMING TO ANSI/IEEE 386. UNIT SHALL

BE DESIGNED FOR DIRECT BURIAL WITH THE JUNCTION MODULES MOUNTED

ABOVE GROUND LINE. PEDESTAL SHALL BE IN CONFORMANCE WITH ANSI

C57.12.28 ENCLOSURE IS A ONE PIECE METAL UNIT WITH SWING UP TOP.

CABLES/CONDUIT SHALL ENTER/EXIT SO THAT LOAD BREAK ELBOWS AND

CABLES MAY BE OPERATED FROM FEED THRUS ON PARKING STANDS OR

JUNCTIONS.

DO NOT INSTALL CONDUIT BENDS TO TRAIN ELBOWS. THIS SHALL ALLOW MORE

CABLE MOVEMENT AND FREEDOM FOR FUTURE SWITCHING.

INCOMING CABLES SHALL BE PROPERLY PHASED AND LABELED BEFORE THEY

ARE POSITIONED AS SHOWN.

ENCLOSURE WILL ACCEPT THREE PRIMARY JUNCTION MODULES. DO NOT

INSTALL PRIMARY JUNCTION MODULES WITH WALL MOUNTING BRACKETS.

ENCLOSURE SHALL BE CORROSION RESISTANT AND SHALL BE FABRICATED OF

STAINLESS STEEL CONFORMING TO ASTM A 167, TYPE 304 OR 304L. PAINT

ENCLOSURE MUNSELL 7GY3.29/1.5 GREEN. PAINT COATING SYSTEM SHALL

COMPLY WITH NEMA C57.12.28. THE MUNSELL COLOR NOTATION IS SPECIFIED IN

ASTM D 1535.

PROVIDE 15 KV 600 AMP ELBOW CONNECTOR FOR EACH TERMINATION.

PROVIDE FAULT INDICATORS ON EACH OUTPUT.

1.

2.

3.

4.

5.

6.

7.

NOTES:

PAD MOUNT PRIMARY TAP BOX DETAIL

NOT TO SCALE

E

E

E E

1 1

HEAT PUMP

208V, 1PH

HEAT PUMP

208V, 1PH

HEAT PUMP

208V, 3PH

HEAT PUMP

208V, 3PH

E

1 (TYP)

The Walker Group Architecture, Inc PO Box 541, New Bern, NC 28563

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

NDEMOLITION FLOOR PLAN

SCALE: 1/8" = 1'-0"

NDEMOLITION MEZZANINE FLOOR PLAN

SCALE: 1/8" = 1'-0"

REMOVE EXISTING LIGHT FIXTURE, EXISTING CIRCUITING TO REMAIN AND

BE REUSED.

EXISTING BUILDING TO BE DEMOLISHED COMPLETELY, SEE ARCHITECTURAL

PLANS.

REMOVE EXISTING AHU CONNECTION IN ATTIC SPACE.

REMOVE EXISTING WATER HEATER CONNECTION.

REMOVE EXISTING PANEL, EXISTING BRANCH CIRCUIT TO REMAIN AND BE

RECONNECTED TO NEW PANEL.

EXISTING LIGHTING CONTROL PANEL TO REMAIN.

EXISTING TELEPHONE SERVICE TO REMAIN.

NOTES THIS SHEET

20 CF

E F G H

0.5

B.1 B.7BA C D

I J K L M N O P

OC

D

V

V D

V V

D

D O

O

D

V

V

OS

OS

OSV V

O

VA

A

A

A

A

A

A

C

C

C

E E E

C

C

D D

E E

B B F F

A A

C C

E E

A

A

A

A

E

K

F

F

ALA-3

ALA-1 ALA-3

C 2

E 2 C 2

G 2 H 2

J 4 C

C C

1 TYP.

1 TYP.

1 TYP.

BABYSITTING

MECH./ ELEC.

TELECOM

OFFICE

OFFICE

VESTIBULE

MEN'S

WOMEN'S

FELLOWSHIP

HALL

KITCHEN

PANTRY

CORRIDOR

JAN.

312UNISEX O

F F

F

F

J 2 TYP

TO

RECEPTACLE

CIRCUIT

MECH.

VESTIBULE

UNISEX

ALTAR

STORAGE

CORRIDOR

CHAPEL

STORAGE

CONFESSIONAL

VESTIBULE 1

The Walker Group Architecture, Inc PO Box 541, New Bern, NC 28563

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

NNEW WORK FIRST FLOOR PLAN

SCALE: 1/8" = 1'-0"

NNEW WORK MEZZANINE FLOOR PLAN

SCALE: 1/8" = 1'-0"

RELAMP EXISTING INCANDESCENT LAMPS WITH LED LAMPS (SIX LAMPS PER

FIXTURE)

CONNECT TO EXISTING CIRCUIT RETAINED DURING DEMOLITION.

ROUTE CIRCUIT THROUGH TIME CLOCK AND PHOTOCELL, FOR CONTROL.

INTERCEPT EXISTING LIGHTING CIRCUIT AND EXTEND AS INDICATED.

INVERTER FOR "ETERNAL FLAME" LIGHT. 1000W, 120V, 1PH. INTERCEPT

EXISTING CIRCUIT AND EXTEND TO INVERTER AND EXISTING CIRCUIT

BREAKER.

NOTES THIS SHEET

STYLE NO. VOLTAGE MOUNTING NOTESFIXTURE

SYMBOL

NUMBER AND

TYPE OF LAMPS

LIGHTING FIXTURE SCHEDULE

NL-2, 2x4 LED UNIVERSAL RECESSED

SURFACE, WALL 8'-0" AFFLEDNL-67

NL-63 LED SURFACE; UNIVERSAL

UNIVERSAL

UNIVERSAL

FIXTURE LUMENS MUST BE 4800, 38 WATTS, FULLY DIMMABLE DRIVER TO 1%, USING 0-10 VCD CONTROLS. PROVIDE

EMERGENCY BATTERY WHERE INDICATED

FIXTURE LUMENS MUST BE 3300, 26 WATTS, NON-DIMMABLE DRIVER. PROVIDE EMERGENCY BATTERY WHERE INDICATED.

FIXTURE LUMENS MUST BE 4800, 32 WATTS. NON-DIMMABLE DRIVER.

FIXTURE LUMENS MUST BE 4000, 38 WATTS, NON-DIMMABLE DRIVER.

FIXTURE LUMENS MUST BE 3000. 35 WATTS, NON-DIMMABLE DRIVER, PROVIDE EMERGENCY BATTERY WHERE INDICATED.

FIXTURE LUMENS MUST BE 2000, 26 WATTS, NON-DIMMABLE DRIVER.

FIXTURE LUMENS MUST BE 3300, 26 WATTS, NON-DIMMABLE DRIVER.

FIXTURE LUMENS MUST BE 4800, 38 WATTS, NON-DIMMABLE DRIVER.

PROVIDE FIXTURE WITH TWO TYPE E HEADS, POLYCARBONATE WHITE HOUSING

PROVIDE FIXTURE WITH WHITE HOUSING AND VOLTMETER.

PROVIDE FIXTURE WITH WHITE HOUSING AND VOLTMETER. PROVIDE SINGLE FACE, RED LETTERING. UNIVERSAL

MOUNTING.

MOUNT FIXTURE TO SIDE OF BEAM. CONNECT TO EXISTING CIRCUIT. PROVIDE WITH LED LAMP 3,000 LUMENS, 6" DIAMETER FIXTURE. PROVIDE DIMMABLE LED DRIVER TO 10%, DRIVER SHALL BE COMPATIBLE WITH THE EXISTING LINE VOLTAGE

DIMMING SYSTEM.

FIXTURE LUMENS MUST BE 1320, 17 WATTS. NON-DIMMABLE DRIVER.

NL-2, 2X2 LED UNIVERSAL RECESSED

3NL-5, 1X4 LED UNIVERSAL SURFACE

NL-10, 1x4 LED UNIVERSAL SURFACE, 6" ABOVE MIRROR 4

NL-19 LED UNIVERSAL RECESSED 5

6SHEET E-501 LED UNIVERSAL SURFACE, CEILING

7NL-7 LED UNIVERSAL SURFACE, 6" ABOVE MIRROR

NL-5, 2x4 LED UNIVERSAL SURFACE 8

NL-54 LED SURFACE; WALL 8'-0"UNIVERSAL 9

SEE DETAIL

NL-20, MODIFIEDLED UNIVERSAL SURFACE 12

NL-5, 1X2 LED UNIVERSAL SURFACE 13

A

B

C

D

E

F

G

H

J

K

& TYPE

20 CF

E F G H

0.5

B.1 B.7BA C D

I J K L M N O P

AC-1

388MCA, 208V, 3PH

600A-3P, NF, 4X

MDP-38; 3 #750 KCMIL,

1 #2 GND - 4"C.

E

GFI GFI GFI

GFI

GFI

MDP

MDA

VFD

E

E

E E

E

E

VAV-2

120V, 1PH

VAV-3

120V, 1PH

VAV-1

120V, 1PH

VAV-5

120V, 1PH

VAV-4

120V, 1PH

GFI

GFI GFI

GFI

GFI

GFI GFI

GFI

GFI

GFI

GFI

GFI

GFI

GFI

GFI

GFI

GFI

EWC

ALA

MDA-4

ALA-14

MDA-6

ALA-12

MDA-37; 3 #8, 1

#10 GND - 1"C.

ALA-4

MDA-2

ALA-2

E

E

MDA-1

30A-2P, FU @ 15, 4X

DSS-1B

9A, 208V, 1PH

CONTROL AND

POWER CABLE

ALA-6

ALA-8

ALA-10

ALA-24

ALA-19

VAV-6

120V, 1PH

MDA-12

ALA-23

ALA-25; 3 #6, 1 #6 GND

- 3/4"C.

ALA-21

WP

M

TO LIGHT

CIRCUIT

EF-2

120V, 1PH

ALA-16

E

VAV-7

120V, 1PH

MDA-14

EF-3

120V, 1PH

MDA-26

MDA-10 MDA-8

ALA-22

ALA-20

ALA-18

E

WH-1

9KW, 208V, 3PH

MDA-32; 3 #10, 1 #10

GND - 3/4"C.

60A-3P, NF

M

HWRP-1

120V, 1PH

MDA-30

MDP-4

MDP-2

MDP-10

MDP-8

MDP-6

WP

WP WP

WP

VAV-8

120V, 1PH

E

MDA-16

MDA-5

MDA-7

MDA-9

GFI

CLA

FACP

CLA-22

EF-1

120V, 1PH

TO LIGHT

CLA-20

E

LIFT STATION

TWO 2HP, 208V, 3PH

MDA-31, 3 #10,

1#10GND IN 3/4"C

CLA-26

A

E-201

MDA-24

EF-5

120V, 1PH

DSS-1A

E

UH-2

3KW,208V, 1PH

MDA-20

MECH.

VESTIBULE

UNISEX

ALTAR

STORAGE

CORRIDOR

CHAPEL

STORAGE

CONFESSIONAL

VESTIBULE

M

M

M M

M

M

M

M

M/WP

BABYSITTING

MECH./ ELEC.

TELECOM

OFFICE

OFFICE

VESTIBULE

MEN'S

WOMEN'S

FELLOWSHIP

HALL

KITCHEN

PANTRY

CORRIDOR

E E

E

M M

M

MDA-30

E

M

E

M

MDA-18

VAV-9

120V, 1PH

RECIR PUMP

120V, 1PH

B-1

120V, 1PH

E

M

E

M

VFD

VFD

B-2

120V, 1PH

SHWP-1

3/4HP, 208V, 3PH

SHWP-2

3/4HP, 208V, 3PH

VFD

MDP

MDP-12

MDP-3

MDP-5

MDP-13

MDP-19

MDP-1

MDP-31, 3 #6,

1 #10 GND-3/4"C

AHU-1

10 HP, 208V, 3PH

E

E

E

E

M

MM

UH-1

120V, 1PH

M

MDP-7

EF-4

120V, 1PH

WP

E

WH-2

1.6KW, 120V, 1PH

MDP-9

MDP-14

DDC PANEL, 120V

M

M

M

MDP-16

DAMPER

120V, 1PH

DAMPER

120V, 1PH

TO LIGHTS

E

MDP-11

The Walker Group Architecture, Inc PO Box 541, New Bern, NC 28563

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

1/8" = 1'-0"

0 4' 16'8'

NNEW WORK FIRST FLOOR PLAN

SCALE: 1/8" = 1'-0"

NENLARGED PLAN - MECHANICAL ROOM

SCALE: 1/4" = 1'-0"

1/4" = 1'-0"

0 2' 8'4'

A

E-201

AHU-2: 7.5HP, 208V, 3PH

DAMPER: 120V, 1PH.

HOOD: 120V, 1PH.

PROVIDE PANEL IN SAME LOCATION AS REMOVED PANEL. RECONNECT

EXISTING CIRCUITS TO PANEL.

GAS SHUT OFF VALVE CONNECTION, 120V, 1PH.

NOTES THIS SHEET

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

REVISED: AUGUST 2004 NL-67LIGHTING PLATE:

DECORATIVE EMERGENCY LIGHTING UNIT

MR16 HALOGEN LAMPS MUST BE 5 WATTS, HIGH-OUTPUT OR AS INDICATED IN

HOUSING - UV STABLE, FLAME-RATED, HIGH-IMPACT THERMOPLASTIC IN WHITE OR

BLACK TEXTURED FINISH.

INTERNAL COMPONENTS - FULLY AUTOMATIC, SOLID STATE, CONSTANT VOLTAGE,

CURRENT-LIMITED BATTERY CHARGER; MAINTENANCE-FREE LEAD-ACID BATTERY;

EXTERIOR HOUSING INDICATORS - LED AC-ON INDICATOR AND INTEGRAL TEST SWITCH.

LAMP HEADS - UV STABLE, FLAME RATED POLYCARBONATE THERMOPLASTIC.

MOUNTING - DIRECTLY TO 4" OCTAGONAL OR SQUARE OUTLET BOX.

CERTIFICATION - UL LISTED AND LABELED. COMPLIES WITH UL 924 AND NFPA 101

OPTIONS - VOLTMETER, VANDAL-RESISTANT SHIELD, SELF-DIAGNOSTIC/TESTING7.

6.

REQUIREMENTS. LISTED FOR DAMP LOCATIONS.

LUMINAIRE REQUIREMENTS:

1.

3.

5.

4.

2.

AND BUILT-IN OVERLOAD AND LOW-VOLTAGE BATTERY PROTECTION.

13"

NOMINAL

NOMINAL

5"

MAX. DEPTH

4" NOMINAL

ELECTRONICS AND WIRE GUARD.

LIGHTING FIXTURE SCHEDULE.

HOUSING - DIE-CAST ALUMINUM OR HIGH-IMPACT, UV-STABILIZED, INJECTION-MOLDED

LETTERS/CHEVRONS - MINIMUM 6" HIGH WITH 3/4" STROKE. RED OR GREEN LETTERS

FINISH (ON CAST ALUMINUM HOUSING ONLY) - TEXTURED POWDER COAT FINISH

OPTIONS INCLUDE WHITE, WHITE WITH BRUSHED ALUMINUM FACE, BLACK, OR BLACK

EMERGENCY PACK - SOLID-STATE, CONSTANT-CURRENT TYPE BATTERY CHARGER WITH

MOUNTING - UNIVERSAL MOUNTING KIT FOR CEILING, WALL OR END-OF-FIXTURE

ILLUMINATION - PROVIDED BY RED, GREEN OR WHITE HIGH-OUTPUT LEDS INSIDE

1.

2.

3.

4.

5.

6.

LUMINAIRE REQUIREMENTS:

REVISED: AUGUST 2004 NL-63

MOUNTING.

THERMOPLASTIC. SINGLE OR DOUBLE-FACED AS INDICATED.

AS INDICATED. PROVIDE CHEVRONS AS INDICATED EITHER LEFT, RIGHT OR BOTH

MAINTENANCE-FREE, NICKEL-CADMIUM BATTERY, AC-ON INDICATOR LAMP AND

LIGHTING PLATE:

LED EXIT SIGN

13"

NOMINAL

NOMINAL

9"

WITH BRUSHED ALUMINUM FACE.

DIRECTIONS AS INDICATED. CHEVRONS PUNCHED OUT THROUGH HOUSING AS REQUIRED.

TEST SWITCH.

OF FIXTURE HOUSING. PROVIDE POLYSTYRENE DIFFUSER IN COLOR INDICATED WITH

FREQUENCY-MATCHED SILKSCREEN COATING FOR MAXIMUM LED LIGHT OUTPUT.

CERTIFICATION - UL LISTED AND CERTIFIED FOR DAMP LOCATIONS.7.

REMOTE EMERGENCY LIGHTING UNITS

LAMPS AND FINISHES MUST BE COMPATIBLE

WITH PRIMARY UNIT WITH WHICH USED.

FOR USE WITH BATTERY UNIT

1.

NOTES:

TYPE - C

REMOTE FIXTURES

TYPE - E

TYPE - D

TYPE - A TYPE - B

SKETCH DATE JUNE 2002 STYLE NL-54

SURFACE LED WRAPAROUND

REVISED: APRIL 2016 NL-5LIGHTING PLATE:

LUMINAIRE REQUIREMENTS:

1. HOUSING - DIE-FORMED, COLD-ROLLED STEEL, WITH REINFORCEMENT RIBS FOR

RIGIDITY; ENDCAPS SAME MATERIAL AS HOUSING, SECURED WITH TABS, SCREWS OR

RIVETS. OPTIONAL LENGTHS OF 2FT OR 4FT.

2. FINISH - MULTI-STAGE PHOSPHATE BONDING TREATMENT FINISHED WITH

HIGH-REFLECTANCE, WHITE POLYESTER POWDER COAT, PAINTED AFTER FABRICATION.

3. LENS - 100% VIRGIN ACRYLIC, CLEAR PRISMATIC DIFFUSER WITH MINIMUM 0.1 INCH

THICKNESS, CONTINUOUSLY SUPPORTED ALONG SIDES OF LUMINAIRE.

4. LIGHT SOURCE - SOLID STATE LEDS WITH MINIMUM 50K HOURS RATED LIFE AT L70, 3500K

CCT UON, MINIMUM 80 CRI, MAXIMUM 4-STEP MCADAM ELLIPSE BINNING TOLERANCE FOR

COLOR CONSISTENCY, AND MINIMUM EFFICACY OF 95 LUMENS/WATT. INITIAL LUMEN

OUTPUT AS INDICATED IN LUMINAIRE SCHEDULE.

5. DRIVER - REPLACEABLE, INTEGRAL, HIGH-EFFICIENCY DRIVER WITH MINIMUM 0.9 PF,

OPERATING VOLTAGE OF 120-277V, THERMAL MANAGEMENT, < 20% TOTAL HARMONIC

DISTORTION. OPTIONAL STEP-DIMMABLE OR FULLY DIMMABLE AS INDICATED.

6. CERTIFICATION - UL 1598, DAMP LOCATION, DLC QUALIFIED, AND ROHS COMPLIANT.

COMPLIES WITH LM79, LM80 AND TM21 TESTING STANDARDS. UL 924 WHEN EQUIPPED

WITH EMERGENCY BATTERY BACK-UP.

7. MOUNTING - SURFACE ON CEILING OR SUSPENDED.

8. THIS SKETCH IS A NON-PROPRIETARY GRAPHIC REPRESENTATION OF A LUMINAIRE THAT

MAY MEET THE SPECIFICATION REQUIREMENTS. IT IS NOT INTENDED TO INDICATE A

CERTAIN MANUFACTURER OR PREFERENCE.

DIRECT/INDIRECT FLUORESCENT TROFFER

REVISED: APRIL 2016 NL-2LIGHTING PLATE:

LUMINAIRE REQUIREMENTS:

1. HOUSING - DIE-FORMED, COLD-ROLLED STEEL, WITH REINFORCEMENT RIBS FOR

RIGIDITY; ENDCAPS SECURED WITH TABS, SCREWS OR RIVETS. OPTIONAL SIZES OF 2FT

x 2FT AND 2FT x 4FT AVAILABLE.

2. FINISH - MULTI-STAGE PHOSPHATE BONDING TREATMENT FINISHED WITH

HIGH-REFLECTANCE, BAKED WHITE ENAMEL OR POLYESTER POWDER COAT.

3. REFLECTORS - TWO-PIECE CURVED ALUMINUM WITH MATTE WHITE FINISH.

4. DIFFUSE BASKET - WHITE PERFORATED OR ACRYLIC.

5. LIGHT SOURCE - LINEAR T8, T5 OR TT5 WITH QUANTITY AND WATTAGE AS INDICATED IN

LUMINAIRE SCHEDULE. 3500K CCT UON; MINIMUM CRI OF 80.

6. BALLAST - PROGRAMMED-START, CLASS P, THERMALLY-PROTECTED, < 20% TOTAL

HARMONIC DISTORTION, HIGH POWER FACTOR (> 0.9), ELECTRONIC TYPE WITH 'A' SOUND

RATING. DIMMING OPTION AVAILABLE.

7. CERTIFICATIONS - UL 1598, DAMP LOCATION, UL 924 WHEN EQUIPPED WITH EMERGENCY

BATTERY BACK-UP.

8. MOUNTING - RECESSED IN SOLID OR ACOUSTICAL TILE CEILING.

9. THIS SKETCH IS A NON-PROPRIETARY GRAPHIC REPRESENTATION OF A LUMINAIRE THAT

MAY MEET THE SPECIFICATION REQUIREMENTS. IT IS NOT INTENDED TO INDICATE A

CERTAIN MANUFACTURER OR PREFERENCE.

WALL MOUNTED FLUORESCENT

REVISED: APRIL 2016 NL-10LIGHTING PLATE:

LUMINAIRE REQUIREMENTS:

1. HOUSING - DIE-FORMED, COLD-ROLLED STEEL, WITH REINFORCEMENT RIBS FOR

RIGIDITY; END CAPS SAME MATERIAL AS HOUSING, SECURED WITH TABS, SCREWS OR

RIVETS. WHITE ENAMEL FINISH APPLIED AFTER FABRICATION. OPTIONAL LENGTHS OF 2

FT, 3 FT OR 4 FT.

2. LENS - ACRYLIC PRISMATIC (CLEAR PRISMATIC PATTERN A12) OR WHITE OPAL, WITH

MINIMUM THICKNESS OF 0.125 IN.

3. LIGHT SOURCE - LINEAR T8, T5 OR T5HO FLUORESCENT TUBES WITH QUANTITY AND

CHARACTERISTICS AS INDICATED IN LUMINAIRE SCHEDULE.

4. BALLAST - PROGRAMMED-START, CLASS P, THERMALLY-PROTECTED, HIGH POWER

FACTOR (>0.9), ELECTRONIC TYPE WITH <20% THD AND 'A' SOUND RATING.

5. CERTIFICATION - UL 1598, DAMP LOCATION, UL 924 WHEN EQUIPPED WITH EMERGENCY

BATTERY BACK-UP.

6. MOUNTING - SURFACE ON WALL.

7. OPTIONS - EMERGENCY BACK-UP, <10% THD BALLAST, DOWNLIGHT COMPONENT ONLY.

8. THIS SKETCH IS A NON-PROPRIETARY GRAPHIC REPRESENTATION OF A LUMINAIRE THAT

MAY MEET THE SPECIFICATION REQUIREMENTS. IT IS NOT INTENDED TO INDICATE A

CERTAIN MANUFACTURER OR PREFERENCE.

LED RECESSED DOWNLIGHT

REVISED: APRIL 2016 NL-19LIGHTING PLATE:

LUMINAIRE REQUIREMENTS:

1. HOUSING - DIE-FORMED, COLD-ROLLED STEEL, OR FORGED ALUMINUM WITH HEAT SINK.

DRIVER MUST BE ACCESSIBLE FROM BOTTOM OF LUMINAIRE. PROVIDE T-BAR HANGERS

FOR INSTALLATION IN ACOUSTICAL TILE CEILINGS OR TABS WHEN MOUNTING IN HARD

CEILINGS.

2. REFLECTOR AND TRIM - SPECIFICATION GRADE, LOW IRRIDESCENT, SPECULAR

ALUMINUM REFLECTOR WITH METALLIC OR PAINTED TRIM RING..

3. LIGHT SOURCE - SOLID STATE LEDS WITH MINIMUM 50K HOURS RATED LIFE AT L70, 3500K

CCT UON, MINIMUM 80 CRI, MAXIMUM 4-STEP MCADAM ELLIPSE BINNING TOLERANCE FOR

COLOR CONSISTENCY, AND MINIMUM EFFICACY OF 90 LUMENS/WATT. INITIAL LUMEN

OUTPUT AS INDICATED IN LUMINAIRE SCHEDULE.

4. DRIVER - REPLACEABLE, INTEGRAL, HIGH-EFFICIENCY DRIVER WITH MINIMUM 0.9 PF,

OPERATING VOLTAGE OF 120-277V, THERMAL MANAGEMENT, < 20% TOTAL HARMONIC

DISTORTION. ON-OFF CONTROL, STEP-DIMMABLE OR FULLY DIMMABLE AS INDICATED.

5. CERTIFICATION - UL 1598, DAMP LOCATION, DLC QUALIFIED, AND ROHS COMPLIANT.

COMPLIES WITH LM79, LM80 AND TM21 TESTING STANDARDS. UL 924 WHEN EQUIPPED

WITH EMERGENCY BATTERY BACK-UP.

6. MOUNTING - RECESSED IN HARD OR ACOUSTICAL TILE CEILING.

7. OPTIONS - EMERGENCY BATTERY BACK-UP, WALL-WASH TRIM, IC RATED FOR DIRECT

CONTACT WITH INSULATION, VARIOUS APERTURE DIAMETERS, AND VARIOUS GLASS

LENSES.

8. THIS SKETCH IS A NON-PROPRIETARY GRAPHIC REPRESENTATION OF A LUMINAIRE THAT

MAY MEET THE SPECIFICATION REQUIREMENTS. IT IS NOT INTENDED TO INDICATE A

CERTAIN MANUFACTURER OR PREFERENCE.

LED INDUSTRIAL STRIP

REVISED: APRIL 2016 NL-7LIGHTING PLATE:

LUMINAIRE REQUIREMENTS:

1. HOUSING - DIE-FORMED, COLD-ROLLED STEEL, WITH REINFORCEMENT RIBS FOR RIGIDITY

AND SPECULAR ALUMINUM OR HIGHLY-REFLECTIVE PAINTED STEEL REFLECTORS.

OPTIONAL LENGTHS OF 4FT OR 8FT.

2. FINISH - MULTI-STAGE PHOSPHATE BONDING TREATMENT FINISHED WITH

HIGH-REFLECTANCE, WHITE POLYESTER POWDER COAT, PAINTED AFTER FABRICATION.

3. LIGHT SOURCE - SOLID STATE LEDS WITH MINIMUM 50K HOURS RATED LIFE AT L70, 3500K

CCT UON, MINIMUM 80 CRI, MAXIMUM 4-STEP MCADAM ELLIPSE BINNING TOLERANCE FOR

COLOR CONSISTENCY, AND MINIMUM EFFICACY OF 100 LUMENS/WATT. INITIAL LUMEN

OUTPUT AS INDICATED IN LUMINAIRE SCHEDULE.

4. DRIVER - REPLACEABLE, INTEGRAL, HIGH-EFFICIENCY DRIVER WITH MINIMUM 0.9 PF,

OPERATING VOLTAGE OF 120-277V, THERMAL MANAGEMENT, < 20% TOTAL HARMONIC

DISTORTION. ON-OFF CONTROL, STEP-DIMMABLE OR FULLY DIMMABLE AS INDICATED.

5. CERTIFICATION - UL 1598, DAMP LOCATION, DLC QUALIFIED, AND ROHS COMPLIANT.

COMPLIES WITH LM79, LM80 AND TM21 TESTING STANDARDS. UL 924 WHEN EQUIPPED

WITH EMERGENCY BATTERY BACK-UP.

6. MOUNTING - SURFACE ON CEILING OR SUSPENDED.

7. OPTIONS - WIRE GUARD, CHAIN, STEM OR SWIVEL STEM HANGERS.

8. THIS SKETCH IS A NON-PROPRIETARY GRAPHIC REPRESENTATION OF A LUMINAIRE THAT

MAY MEET THE SPECIFICATION REQUIREMENTS. IT IS NOT INTENDED TO INDICATE A

CERTAIN MANUFACTURER OR PREFERENCE.

INDICATE

LENGTH

SURFACE MOUNT

TYPE A

PENDANT MOUNT

TYPE B

WALL MOUNT

TYPE C

LAMP OPTIONS

2 F13/T4 DOUBLE TWIN TUBE COMPACT FLUORESCENT LAMPS.

2 F26/T4 DOUBLE TWIN TUBE COMPACT FLUORESCENT LAMPS.

LUMINAIRE REQUIREMENTS

HOUSING - ALUMINUM .050"± THICK WITH WHITE ACRYLIC ENAMELED

FINISH. PROVIDE INTERNAL GREEN GROUNDING SCREW.

REFLECTOR - SPECULAR ALUMINUM.

BALLAST - HIGH POWER FACTOR ( > .9) ELECTROMAGNETIC BALLAST.

LENS TRIM RING - ALUMINUM WITH WHITE ACRYLIC ENAMELED

FINISH.

REGRESS - 1" MATTE BLACK FROM TRIM RING UP TO LENS.

LENS - FLAT PRISMATIC GLASS.

1.

2.

1.

2.

3.

4.

5.

6.

7.

8.

9.

SKETCH DATE JUNE 2002 STYLE NL-20

ROUND-SURFACE, PENDANT OR WALL MOUNT

COMPACT FLUORESCENT - INTERIOR/EXTERIOR

MINIMUM FIXTURE EFFICIENCY - 60%.

MINIMUM SPACING CRITERIA: 1.2

HOUSING DIMENSIONS - 12" DIA. ±1" X 6" HIGH ±1".

FIXTURE SHALL HAVE UL LABEL FOR WET OR DAMP LOCATIONS

AS INDICATED.

10.

DETAIL BASED ON LITHONIA LIGHTING, "VR4" SERIES

LUMINAIRE DESCRIPTION:

1. HOUSING MUST BE 0.054" THICK (MINIMUM) MARINE GRADE ALUMINUM

BACK PLATE.

2. HOUSING MUST BE FULLY GASKETED AROUND LENS, AND BETWEEN

LUMINAIRE AND CEILING, WITH DOUBLE BAKED NEOPRENE GASKETS.

PROVIDE INTERNAL GREEN GROUNDING SCREW.

3. LENS MUST BE PRISMATIC POLYCARBONATE HELD IN PLACE WITH 4

STAINLESS STEEL SCREWS.

4. MOUNT BACK PLATE TO CEILING WITH (4) 1/4"Ø SCREWS OR ANCHORS.

5. PROVIDE WIRING COMPARTMENT SUITABLE FOR USE WITH 60°C WIRE

INSULATION.

6. FIXTURE MUST BE UL LISTED FOR WET LOCATIONS.

TYPE LAMP # LAMP TYPE INPUT WATTS VOLTAGE MOUNTING

SURFACE, CEILING120/27726LEDNA

CEILING-MOUNTED VANDAL-RESISTANT LUMINAIRE

12"

8"

LIGHTING DETAIL F - LED

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

02/24/2020

PANEL

MDP

800A MCB

208/120V 3P, 4W

22 KAIC

PANEL

CLA

200A MLO

208/120V 3P, 4W

22 KAIC

PANEL

MDA

225A MCB

208/120V 3P, 4W

22 KAIC

PANEL

ALA

150A MLO

208/120V 3P, 4W

22 KAIC

ELECTRICAL LOAD SUMMARY

LOAD CONNECTED DEMAND DEMAND

DESCRIPTION LOAD FACTOR LOAD

LIGHTING 17.1 KVA 100% 17.1 KVA

EXTERIOR LIGHTING 3.0 KVA 100% 3.0 KVA

RECEPTACLES 21.9 KVA NOTE - 116.0 KVA

AIR CONDITIONING 168.3 KVA 100% 168.3 KVA

HEATING 13.9 KVA 100% 13.9 KVA

VENTILATION 2.0 KVA 100% 2.0 KVA

MISCELLANEOUS 6.9 KVA 100% 6.9 KVA

KITCHEN EQUIP. 10.6 KVA 100% 10.6 KVA

WATER HEATER 15.7 KVA 100% 15.7 KVA

TOTAL 259.3 KVA 253.4 KVA

NOTES:

1. 1st 10 KVA @ 100%, REMAINDER @ 50%

PANELBOARD MDP SCHEDULE

SEE POWER RISER DIAGRAM FOR RATINGS

LOAD (AMPS) BKR CKT PHASE CKT BKR LOAD (AMPS)

LOAD SERVED A B C TRIP NO. A B C NO. TRIP A B C LOAD SERVED

BOILER #1 4.5 20/1P 1 2 20/1P 10.0 HEAT TRACE

BOILER #2 4.5 20/1P 3 4 20/1P 10.0 HEAT TRACE

RECIRC PUMPS 7.0 20/1P 5 6 20/1P 10.0 HEAT TRACE

EF/UH 3.0 20/1P 7 8 20/1P 10.0 HEAT TRACE

WH-2 13.8 20/1P 9 10 20/1P 10.0 HEAT TRACE

GAS VALVE 1.5 20/1P 11 12 20/1P 3.0 RECEPTACLES

SHWP-1 3.5 20/3P 13 14 20/1P 3.0 DDC

3.5 16 20/1P 5.0 DAMPERS

3.5 18 20/1P SPARE

SHWP-2 3.5 20/3P 19 20 20/1P SPARE

3.5 22 20/1P SPARE

3.5 24 20/1P SPARE

PANEL CLA 92.5 200/3P 25 26 20/1P SPARE

70.0 28 20/1P SPARE

90.0 30 20/1P SPARE

AHU-1 30.8 60/3P 31 32 225/3P 197.2 PANEL MDA

30.8 201.6

30.8 138.6

SPD 60/3P 37 38 450/3P 388.0 CHILLER

388.0 388.0

TOTAL 137.8 126.1 136.3 608.2 614.6 539.6 TOTAL

TOTAL CONNECTED AMPS A: 746.0 B: 740.7 C: 675.9

PANELBOARD CLA SCHEDULE

SEE POWER RISER DIAGRAM FOR RATINGS

LOAD (AMPS) BKR CKT PHASE CKT BKR LOAD (AMPS)

LOAD SERVED A B C TRIP NO. A B C NO. TRIP A B C LOAD SERVED

LTG/RECEPT LEFT 5.0 20/1P 1 2 20/1P 10.0 STEEPLE LIGHTS

LTG/RECEPT CONFESS 5.0 20/1P 3 4 20/1P 5.0 LTG/RECEPT STORAGE

RECEPT - LOFT 5.0 20/1P 5 6 20/1P 5.0 LTG/RECEPT ATTIC

WATER HTR STORAGE 12.0 20/1P 7 8 20/1P 5.0 LTG/RECEPT FOYER

LTG/RECEPT STORAGE 5.0 20/1P 9 10 20/1P SPARE

LTG/RECEPT RIGHT 5.0 20/1P 11 12 20/1P 5.0 LTG ELEC & TOILET

RECEPT - STORAGE 5.0 20/1P 13 14 20/1P 5.0 LTG - BACK HALL

TRACK - BACK STAGE 5.0 20/1P 15 16 20/1P 5.0 TRACK LIGHTING

TRACK - CNR STAGE 5.0 20/1P 17 18 20/1P SPARE

RECEPT - BACK STAGE 5.0 20/1P 19 20 20/1P 1.5 RECEPT - TOILET

RECEPT - BACK STAGE 5.0 20/1P 21 22 20/1P 5.0 FIRE ALARM

DIMMER PANEL 35.0 60/3P 23 24 40/1P 30.0 WATER HEATER

35.0 26 20/1P 9.0 RECEPT -ALTER

35.0 28 20/1P SPARE

SPARE 20/1P 29 30 20/1P SPARE

SPARE 20/1P 31 32 20/1P SPARE

SPARE 20/1P 33 34 20/1P SPARE

SPARE 20/1P 35 36 20/1P SPARE

SPARE 20/1P 37 38 20/1P SPARE

SPARE 20/1P 39 40 20/1P SPARE

SPARE 20/1P 41 42 20/1P SPARE

TOTAL 62.0 55.0 50.0 30.5 15.0 40.0 TOTAL

TOTAL CONNECTED AMPS A: 92.5 B: 70.0 C: 90.0

PANELBOARD MDA SCHEDULE

SEE POWER RISER DIAGRAM FOR RATINGS

LOAD (AMPS) BKR CKT PHASE CKT BKR LOAD (AMPS)

LOAD SERVED A B C TRIP NO. A B C NO. TRIP A B C LOAD SERVED

TELE RM AC 9.0 15/2P 1 2 20/1P 5.8 VAV-1

DSS-A & B 9.0 4 20/1P 5.8 VAV-2

RECEPT - TEL ROOM 3.0 20/1P 5 6 20/1P 5.8 VAV-3

RECEPT - TEL ROOM 3.0 20/1P 7 8 20/1P 5.8 VAV-4

RECEPT - TEL ROOM 4.5 20/1P 9 10 20/1P 5.8 VAV-5

SPARE 20/1P 11 12 20/1P 5.8 VAV-6

SPARE 20/1P 13 14 20/1P 5.8 VAV-7

SPARE 20/1P 15 16 20/1P 5.8 VAV-8

SPARE 20/1P 17 18 20/1P 5.8 VAV-9

SPARE 20/1P 19 20 20/2P 14.4 UH-2

SPARE 20/1P 21 14.4

SPARE 20/1P 23 24 20/1P 3.0 EF-4

SPARE 20/1P 25 26 20/1P 2.4 EF-3

SPARE 20/1P 27 28 20/1P 3.0 DAMPERS

SPARE 20/1P 29 30 20/1P 2.7 HW RECIRC PUMP

LIFT STATION 18.7 30/3P 31 32 40/3P 25.0 WH-1

18.7 25.0

18.7 25.0

AHU-2 24.2 50/3P 37 38 150/3P 83.1 PANEL ALA

24.2 85.4

24.2 44.6

TOTAL 54.9 56.4 45.9 142.3 145.2 92.7 TOTAL

TOTAL CONNECTED AMPS A: 197.2 B: 201.6 C: 138.6

PANELBOARD ALA SCHEDULE

SEE POWER RISER DIAGRAM FOR RATINGS

LOAD (AMPS) BKR CKT PHASE CKT BKR LOAD (AMPS)

LOAD SERVED A B C TRIP NO. A B C NO. TRIP A B C LOAD SERVED

LIGHTING 7.5 20/1P 1 2 20/1P 7.5 RECEPT - 311

LIGHTING 4.9 20/1P 3 4 20/1P 6.0 RECEPT - 311

EXTERIOR LIGHTING 4.0 20/1P 5 6 20/1P 3.0 RECEPT - 311

EXTERIOR LIGHTING 4.1 20/1P 7 8 20/1P 3.0 RECEPT - 311

EXTERIOR LIGHTING 12.5 20/1P 9 10 20/1P 4.5 RECEPT - 311

EXTERIOR LIGHTING 4.1 20/1P 11 12 20/1P 10.5 RECEPT - 307

SPARE 20/1P 13 14 20/1P 7.5 RECEPT - 308

SPARE 20/1P 15 16 20/1P 10.5 RECEPT - TOILETS

SPARE 20/1P 17 18 20/1P G 12.5 REECPT - EWC

RECEPT - KIT 314 12.5 20/1P 19 20 20/1P 6.0 RECETP - 304

RECEPT - KIT 314 3.0 20/1P 21 22 20/1P 9.0 RECETP - 304

RECEPT - KIT 314 3.0 20/1P 23 24 20/1P 7.5 RECETP - 304

OVEN 35.0 50/2P 25 26 20/1P SPARE

35.0 28 20/1P SPARE

SPARE 20/1P 29 30 20/1P SPARE

SPARE 20/1P 31 32 20/1P SPARE

SPARE 20/1P 33 34 20/1P SPARE

SPARE 20/1P 35 36 20/1P SPARE

SPARE 20/1P 37 38 20/1P SPARE

SPARE 20/1P 39 40 20/1P SPARE

SPARE 20/1P 41 42 20/1P SPARE

TOTAL 59.1 55.4 11.1 24.0 30.0 33.5 TOTAL

TOTAL CONNECTED AMPS A: 83.1 B: 85.4 C: 44.6

G - INDICATED GFI CIRCUIT BREAKER

POWER RISER DIAGRAM

NOT TO SCALE

SERVICE GROUND:

1 #6 - 1/2"C TO GROUND ROD

1 #3/0 - 1/2"C TO WATER SERVICE

1 #3/0 - 1/2"C TO BUILDING STEEL

1 #3/0 - 1/2"C TO REBAR IN SLAB

SERVICE GROUND:

1 #6 - 1/2"C TO GROUND ROD

1 #2 - 1/2"C TO WATER SERVICE

1 #2 - 1/2"C TO BUILDING STEEL

1 #2 - 1/2"C TO REBAR IN SLAB

4 #1/0, 1 #6 GND - 2"C

4 - #4/0, 1 #4 GND - 2-1/2"C

4 #3/0, 1 #6 GND - 2-1/2"C

TWO 4" CONDUITS WITH

4- 600 KCMIL IN EACH CONDUIT AND ONE

SPARE 4"C TO TRANSFORMER

SPD

4 #6, 1 #8 GND - 3/4"C

CC

TC

P

SITE LIGHTING CONTACTOR:

6 POLE, 120V, 20A.

CONTROL MUST BE

PHOTOCELL ON,

TIME CLOCK OFF

TO SITE LIGHTING

CIRCUITS

SEE PRIMARY ONE-LINE

DIAGRAM SHEET ES102

FOR CONTINUATION

Name: Service Transformer "X" * Type: 120/208, 3p, 150kVA Source N/A Impedance (%Z) 2 Voltage 208 KVA 150 Phase 3 Full Load Amps 417 Voltage Fluctuation: 1.05 Multiplier 50.00 Fault Current 21885

Name: Panel MDP * Conductor Size: 600KCMIL Source: Service Transformer "X" Material: Copper Voltage 208 Conduit Type: Non-Magnetic Phase 3 5 Voltage Rating: Up To 5KV Available Fault Current 21885 Constant 25000 Multiplier 0.846 Conductors/Phase: 2 Fault Current 18515 Length (ft): 50 Load (Amps): 630 1.1 Voltage Drop (%) 1.1 (0.5%)

Name: Panel "CLA" * Conductor Size: #3/0 Source: Panel MDP Material: Copper Voltage 208 Conduit Type: Magnetic Phase 3 7 Voltage Rating: Up To 5KV Available Fault Current 18515 Constant 10638 Multiplier 0.580 Conductors/Phase: 1 Fault Current 10741 Length (ft): 50 Load (Amps): 160 1.3 Voltage Drop (%) 1.3 (0.6%) Name: Panel "MDA" * Conductor Size: #4/0 Source: Panel MDP Material: Copper Voltage 208 Conduit Type: Non-Magnetic Phase 3 5 Voltage Rating: Up To 5KV Available Fault Current 18515 Constant 13514 Multiplier 0.467 Conductors/Phase: 1 Fault Current 8654 Length (ft): 100 Load (Amps): 180 2.3 Voltage Drop (%) 2.3 (1.1%) Name: Panel "ALA" * Conductor Size: #1/0 Source: Panel "MDA" Material: Copper Voltage 208 Conduit Type: Magnetic Phase 3 7 Voltage Rating: Up To 5KV Available Fault Current 8654 Constant 7692 Multiplier 0.914 Conductors/Phase: 1 Fault Current 7913 Length (ft): 10 Load (Amps): 120 0.3 Voltage Drop (%) 0.3 (0.1%)