N4008519B0095 Drawings_Part3.pdf

02/24/2020

The Walker Group Architecture, Inc PO Box 541, New Bern, NC 28563

252.636.8778 (PHONE)

252.636.8992 (FAX)

WALKER

GROUP

i n c o r p o r a t e d the

ARCHITECTURE

DISCLOSURE OF INFORMATION

CONTRACTOR SHALL COMPLY AS FOLLOWS:

(A) THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS-

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE DATE OF RELEASE

(B) REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL

SUBMIT ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE FOR RELEASE.

(C) THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT UNDER HIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

WALL WORK NOTE:

PLUMBING CONTRACTOR SHALL REMOVE PORTIONS OF EXISTING WALLS AS

REQUIRED FOR ACCESS TO EXISTING PLUMBING PIPING FOR REMODELING

WORK. CONTRACTOR SHALL PATCH TO MATCH EXISTING ADJACENT CONDITIONS

AND RATINGS. REFER TO ARCHITECTURAL PLAN FOR PATCHING DETAILS AND

NOTES.

PLUMBING COORDINATION NOTE:

CONTRACTOR SHALL VERIFY AND COORDINATE THE EXACT LOCATION OF ALL

MECHANICAL, ELECTRICAL, PLUMBING, AND STRUCTURAL SYSTEMS AND

COMPONENTS (EXISTING AND NEW) PRIOR TO COMMENCING WORK. THE FAILURE

TO COMPLY WITH THIS DIRECTION SHALL NOT CONSTITUTE THE BASIS FOR A

CHANGE ORDER SHOULD REWORK BE REQUIRED.

ANY CONDITIONS FOUND THAT WILL PROHIBIT MAKING THE FINAL

CONNECTIONS(S) OR EXECUTION OF THE WORK SHALL BE REPORTED TO THE

COTR IMMEDIATELY.

ANY SHUT DOWNS OR INTERRUPTIONS IN SERVICE SHALL BE APPROVED BY THE

GOVERNMENT IN ACCORDANCE WITH THE SPECIFICATIONS. THE CONTRACTOR

SHALL ALSO BE RESPONSIBLE FOR ANY DELAYS TO THE PROJECT THAT ARISE

DUE TO HIS FAILURE TO COMPLY WITH THESE REQUIREMENTS.

MANUFACTURER'S RECOMMENDATIONS:

ALL MATERIAL AND EQUIPMENT MUST BE INSTALLED IN ACCORDANCE WITH

THE MANUFACTURER'S RECOMMENDATIONS FOR THE INTENDED PURPOSE.

USE THE MORE STRINGENT METHODS WHEN MANUFACTURER'S

RECOMMENDATIONS DIFFER FROM REQUIREMENTS LISTED IN THE PLANS AND

SPECIFICATIONS. BRING ANY CONFLICTS BETWEEN MANUFACTURER'S

RECOMMENDATIONS, PLANS AND SPECIFICATION REQUIREMENTS TO THE

GOVERNMENT'S ATTENTION.

GENERAL NOTES

ALL PLUMBING VENTS IN EXTERIOR WALLS SHALL BE OFFSET A MINIMUM OF 3'-0" AT ROOF

BEFORE ROOF PENETRATION.

ALL PLUMBING VENTS WITHIN A 10'-0" RADIUS OF ANY ROOF TOP UNIT SHALL BE EXTENDED

TO A HEIGHT OF 3'-0" ABOVE THE FRESH AIR INTAKE.

ALL WALL HYDRANTS SHALL BE MOUNTED 24" ABOVE FINISHED GRADE UNLESS OTHERWISE

SPECIFIED.

SLOPES & INVERT ELEVATIONS OF ALL INTERIOR PIPING SHALL BE ESTABLISHED BEFORE

ANY PIPING IS INSTALLED, IN ORDER THAT PROPER SLOPES WILL BE MAINTAINED. ALL

PIPING SHALL BE RUN TO AVOID CONFLICTS WITH OTHER TRADES.

MAKE PROPER HOT & COLD WATER, HOT WATER RECIRCULATING, WASTE, & VENT, ETC.,

PIPING CONNECTIONS TO ALL FIXTURES & EQUIPMENT EVEN THOUGH ALL BRANCHES,

FITTINGS & CONNECTIONS ARE NOT SHOWN.

COORDINATE LOCATION OF ALL EQUIPMENT, FIXTURES & PIPING WITH STRUCTURAL & ALL

OTHER TRADES. PIPING RUN ABOVE CEILING SHALL BE RUN AS HIGH AS POSSIBLE.

ALL OPENINGS IN CEILINGS & PLENUM WALLS FOR PLUMBING PIPES SHALL BE SEALED AIR

TIGHT.

SEE SITE PLAN FOR EXTENT OF ALL PIPING LEAVING & ENTERING BUILDING.

ALL HOT & COLD WATER PIPING INDICATED TO RUN ABOVE FINISHED CEILINGS OR IN

EXTERIOR WALLS SHALL BE INSTALLED ON THE CONDITIONED SPACE SIDE OF THE

BUILDING INSULATION.

SLOPES & INVERT ELEVATIONS OF EXTERIOR SEWERS, MANHOLES, ETC., MUST BE

ESTABLISHED & VERIFIED BEFORE ANY PIPING IS INSTALLED IN ORDER THAT PROPER

SLOPES WILL BE MAINTAINED & NECESSARY INVERT ELEVATIONS OBTAINED.

PROVIDE AUTOMATIC TRAP PRIMERS & TRAP GUARDS FOR ALL FLOOR DRAINS WHERE

INDICATED. MOUNT TRAP PRIMER IN ACCESSIBLE LOCATION.

IT IS THE INTENTION OF THESE DRAWINGS TO COVER ALL WORK & MATERIAL FOR A

COMPLETE FIRST CLASS INSTALLATION. ANY EQUIPMENT, PLUMBING FIXTURE, TRIM

HARDWARE &/OR DEVICES USUALLY UTILIZED IN THE CLASS OF WORK, THOUGH NOT

SPECIFICALLY MENTIONED OR SHOWN ON THE DRAWINGS, BUT WHICH MAY BE NECESSARY

FOR THE SATISFACTORY COMPLETION OF THE WORK (AS DETERMINED BY THE

GOVERNMENT) MUST BE FURNISHED & INSTALLED BY THE CONTRACTOR AS PART OF HIS

TOTAL WORK.

VERIFY ALL EXISTING CONDITIONS PRIOR TO BEGINNING WORK OR ORDERING EQUIPMENT,

PIPING, FIXTURES, ETC.

SEAL AROUND ALL WALL PENETRATIONS AIR TIGHT & FILL ANY VOIDS.

INSTALL ALL EQUIPMENT IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS &

ALL APPLICABLE LISTING REQUIREMENTS.

SANITARY WASTE PIPE SERVING KITCHEN AREAS THAT RECEIVES 140°F OR ABOVE

DISCHARGE WATER FROM KITCHEN EQUIPMENT SHALL BE CAST IRON.

INTERDISCIPLINARY COORDINATION:

IF THIS CONTRACTOR SHOULD ELECT TO PROPOSE ANY EQUIPMENT THAT HAS DIFFERENT

PHYSICAL OR ELECTRICAL CHARACTERISTICS, ETC. WHEN COMPARED TO THE BASIS OF

DESIGN EQUIPMENT, THIS CONTRACTOR IS RESPONSIBLE FOR COORDINATING THESE

CHANGES WITH THE OTHER TRADES PRIOR TO ORDERING OF EQUIPMENT. IF THERE

SHOULD BE ANY ADDITIONAL WORK INCURRED BY THE OTHER TRADES AS A RESULT OF

THIS CONTRACTOR'S EQUIPMENT SELECTION, ALL COSTS ASSOCIATED WITH THE

ADDITIONAL WORK SHALL BE BORNE BY THIS CONTRACTOR.

DOMESTIC HOT WATER RETURN (HWR)

NEW POINT OF CONNECTION

VENT THROUGH ROOF (VTR)

SANITARY WASTE PIPE (WP)

SANITARY VENT PIPE (VP)

FLOOR DRAIN (FD)

PIPE TURN UP

PIPE TURN DOWN (DN)

CHECK VALVE (CV)

PIPE SLEEVE

BALANCING VALVE (BV)

PIPE CAPPED

WALL HYDRANT (WH)

BALL VALVE (BV)

STRAINER

WALL CLEAN OUT (WCO)

CLEAN OUT (CO)

LIMIT OF DEMOLITION WORK

DEMOLITION NOTE DESIGNATION

NEW WORK NOTE DESIGNATION

REDUCED PRESSURE

FLOOR CLEAN OUT (FCO)

EXISTING PIPING TO REMAIN

EXISTING PIPING TO BE REMOVED

DOMESTIC COLD WATER (CW)

DOMESTIC HOT WATER (HW)

LEGEND & ABBREVIATIONS

BACKFLOW PREVENTER (RPBP)

GRADE CLEAN OUT (GCO)

PLUMBING FIXTURE MARK

PHASE/DIAMETER

TEMPERATURE

AUTOMATIC TRAP PRIMER

KILOWATTS

MIN MINIMUM

P-#

Ø

TEMP

TYP TYPICAL

DEGREE

W/ WITH

TP

EXISTINGEXIST

BFF BELOW FINISH FLOOR

ELEV ELEVATION

FAHRENHEITF

GAL GALLON

HP HORSE POWER

GPM GALLONS PER MINUTE

HEADHD

INVERTINV

MAX MAXIMUM

ADA

AC ABOVE CEILING

KW

AMERICANS WITH

DISABILITIES ACT COMPLIANT

ETR EXISTING TO REMAIN

WALL HYDRANTWH

WATER HEATER MARKWH-#

DFU DRAINAGE FIXTURE UNIT

SUPPLY FIXTURE UNITSFU

REDUCED PRESSURERPBP

BACKFLOW PREVENTER

ASSE AMERICAN SOCIETY OF

SANITARY ENGINEERING

TRAP GUARDTG

HWRP-# HOT WATER RECIRCULATION

PUMP MARK

BG BELOW GRADE

FOOTFT

WATER HAMMER ARRESTOR (WHA)

AFF ABOVE FINISHED FLOOR

VS VENT STACK

SAW CUT NOTE:

VERIFY PIPE INVERTS PRIOR TO SAW CUTTING. SAW CUT, REMOVE AND PATCH

CONCRETE FLOOR AS REQUIRED TO PERFORM WORK INDICATED. PATCH FLOOR

TO MATCH ADJACENT EXISTING CONDITIONS AND NEW CONDITIONS.

FIRE STOPPING NOTE:

CONTRACTOR MUCH PROVIDE AN APPROPRIATE LISTED THROUGH-PENETRATION

FIRE STOPPING ASSEMBLY AT EACH PENETRATION OF FIRE RATED

CONSTRUCTION (I.E. WALLS AND SLABS, ETC.). SLEEVES MUCH ONLY BE

PERMITTED WHERE INDICATED IN THE CONTRACTOR SELECTED

THROUGH-PENETRATION FIRE STOPPING ASSEMBLY. REFER TO ARCHITECTURAL

DRAWINGS FOR LOCATION OF ALL RATED ASSEMBLIES AND ASSOCIATED UL

DESIGNATIONS. DEVICES INSTALLED RECESSED WITHIN FIRE RATED

CONSTRUCTION (I.E. COPPER PIPING ETC.) ARE ONLY PERMITTED WHEN AN

APPROVED LISTED FIRE STOPPING SYSTEM EXISTS FOR THE APPLICATION. IF AN

APPROVED LISTED FIRE STOPPING SYSTEM IS UNAVAILABLE, THE CONTRACTOR

MUCH BRING THE CONDITION TO THE ATTENTION OF THE GOVERNMENT FOR

RESOLUTION PRIOR TO PROCEEDING WITH WORK.

DETAIL

SCALE: XXX X-XXX

X

DETAIL NUMBER NAME

SCALE

SHEET REFERENCED FROM

DETAIL TAG

DETAIL NUMBER

SHEET WHERE DRAWN

AutoCAD SHX Text

T. HAHN

AutoCAD SHX Text

P. MCNALLY

AutoCAD SHX Text

P. MCNALLY

AutoCAD SHX Text A

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text G

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text V

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text H

AutoCAD SHX Text T

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text E

AutoCAD SHX Text W

AutoCAD SHX Text N

AutoCAD SHX Text O

AutoCAD SHX Text M

AutoCAD SHX Text M

AutoCAD SHX Text O

AutoCAD SHX Text C

AutoCAD SHX Text P

AutoCAD SHX Text R

AutoCAD SHX Text O

AutoCAD SHX Text F

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text I

AutoCAD SHX Text O

AutoCAD SHX Text N

AutoCAD SHX Text A

AutoCAD SHX Text L

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text G

AutoCAD SHX Text I

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text

TIMOTHY N. HAHN

AutoCAD SHX Text Lic. No. 058039

AutoCAD SHX Text

SATISFACTORY TO: DATE

AutoCAD SHX Text

APPROVED: PWO OR OICC DATE

AutoCAD SHX Text

DESIGN DIR.

AutoCAD SHX Text

SUBMITTED BY:

AutoCAD SHX Text

CHK.

AutoCAD SHX Text

DR.

AutoCAD SHX Text

DES.

AutoCAD SHX Text

SYM

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

CODE IDENT. NO

AutoCAD SHX Text

SIZE

AutoCAD SHX Text F

AutoCAD SHX Text

SPEC.

AutoCAD SHX Text

SCALE: NOTED

AutoCAD SHX Text

DEPARTMENT OF THE NAVY NAVAL FACILITIES ENGINEERING COMMAND

AutoCAD SHX Text

NAVFAC DRAWING NO.

AutoCAD SHX Text

CONST. CONTR. NO.

AutoCAD SHX Text

CAMP LEJEUNE, NORTH CAROLINA

AutoCAD SHX Text

MARINE CORPS BASE

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

DATE

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

CATHOLIC CHAPEL, BLDG 17 AND 17A MCB CL NC

AutoCAD SHX Text

19-0095 RENOVATION AND ADDITION TO THE

AutoCAD SHX Text

T.H. BURTON P.E.

AutoCAD SHX Text

B.WALKER

AutoCAD SHX Text

AutoCAD SHX Text 60025671

AutoCAD SHX Text

AutoCAD SHX Text P-001

AutoCAD SHX Text

PLUMBING GENERAL NOTES, LEGEND, & ABBREVIATIONS