Attachment X. BC R550 RESCUE KIT – User Instruction Guide (PWS attachment A).pdf

© 3M 2020

ANSI Z359.4

CSA Z259.2.3

OSHA 1926.502

OSHA 1910.140

USER INSTRUCTIONS

5903520 REv. G

3325XXX

3327XXX

3325XXX

A L W

3325100 100 ft.

(30.48 m)

12.75 lb.

(5.78 kg)

3325200 200 ft.

(60.96 m)

16.6 lb.

(7.5 kg)

3325275 275 ft.

(83.82 m)

19.4 lb.

(8.8 kg)

3325300 300 ft.

(91.44 m)

20.4 lb.

(9.25 kg)

L

L

3326XXX

A L W

3326100 100 ft.

(30.48 m)

35.3 lb.

(16.0 kg)

3326300 300 ft.

(91.44 m)

42.9 lb.

(19.5 kg)

3326350 350 ft.

(106.7 m)

44.8 lb.

(20.3 kg)

3327XXX

A L W

3327050 50 ft.

(15.24 m)

12.0 lb.

(5.4 kg)

3327100 100 ft.

(30.48 m)

13.9 lb.

(6.3 kg)

3327150 150 ft.

(45.72 m)

15.8 lb.

(7.2 kg)

3327200 200 ft.

(60.96 m)

17.7 lb.

(8.0 kg)

3327275 275 ft.

(83.82 m)

20.5 lb.

(9.3 kg)

3327300 300 ft.

(91.44 m)

21.5 lb.

(9.75 kg)

3327325 325 ft.

(99.06 m)

22.4 lb.

(10.2 kg)

3327350 350 ft.

(106.7 m)

23.9 lb.

(10.8 kg)

3327400 400 ft.

(121.9 m)

25.75 lb.

(11.68 kg)

3327500 500 ft.

(152.4 m)

29.55 lb.

(13.4 kg)

3327600 600 ft.

(182.9 m)

33.25 lb.

(15.0 kg)

3326XXX

RoLLgLiss® R550 Rescue & Escape Device

B

D

EH

C

F

G

A

H

H

3 5

A B C

A. B. C. D.

E. F. G.

A

D

B

E

C

F

G

B

C

A

A

D

B

A E

C

7 8

F

E

G

D

C

B

A

A B

C

B

L

A

RH R

A

C

RH

RD

RL

∅8mm-16mm

L

E

VL

D

10 11

1 3

B

A

A

C

A

B

1 2 3

LA

VE

NDER INDICATES

H

U M

IDITY

30 40

B A

F D

B

C

E

A

A

LA

VE

NDER INDICATES

H

U M

IDITY

30 40

E

B

A

C

D E

Before each use, inspect device in accordance with user manual, including condition of connectors, legibility of labels, and evidence of damage, defects, or missing parts.

Inspection by a competent person required at least annually.

See user manual. - Avant chaque utilisation, inspectez l'équipement selon le manuel de l'utilisateur, y compris l'état des connecteurs, la lisibilité des étiquettes et tout indice de dommage, de défaut ou de pièce manquante. L'inspection doit être faite par une personne qualifiée au moins une fois par an. Consultez le manuel de l'utilisateur.

Mfrd (yr/mo):

(aa/mo):

Lot:

Model No:

N° de modèle:

System Length (m, ft):

Longueur du système (m, pi):

Rollgliss R550 Rescue &

Escape Device

CSA Z259.2.3-16 TYPE 1A

MEETS: OSHA and

ANSI/ASSE Z359.4

(ANSI: SINGLE

USER 130-310 lb) www.capitalsafety.com

Avoid descending into electrical, thermal, chemical or other hazards. Use only the rope provided by Capital Safety as part of this system.

See User Manual for additional information.

Évitez les descentes près des sources de chaleur, de courant électrique ou de produits chimiques.

N'utilisez que la corde fournie par Capital Safety avec cet équipement. Consultez le manuel de l'utilisateur pour de plus amples renseignements.

WARNING AVERTISSEMENT

INSPECTION:

Two users up to/Deux utilisateurs jusqu'à 282 kg (620 lb) - 350 m (1148 ft) Single users to/Un seul utilisateur jusqu'à 141 kg (310 lb) - 5500 m (18044 ft) Single users to/Un seul utilisateur jusqu'à 100 kg (220 lb) - 7755 m (25442 ft) Single users to/Un seul utilisateur jusqu'à 75 kg (165 lb) - 11000 m (36089 ft)

SPECIFICATIONS:

Rope Material: 9.5 mm (3/8") polyamide static kernmantle rope Matériau de la corde : Corde d'alpinisme statique en polyamide de 9,5 mm (3/8 po) Anchorage Strength Required / Résistance d'ancrage requise 1406 kg (3100 lbs)

9510144 Rev. D

1k g (3 lb

M ax

0m (1

ft) M ax

1k g (3 lb

0m (3 ft

M ax . O

R

A B1

B2 kg (6 lb) m (3

ft) M ax

2k g (6 lb

M ax

5m (5 ft

M ax

A

E

C

DB

C

D

E

F

A

I

J

K

B

G

H

L

FORM NO: 5908259 REV: A 7

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Pre- Engineered Rescue System. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Pre-Engineered Rescue System is intended for use as part of a complete personal fall protection and/or rescue system.

Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not described in the User Instructions, is not approved by 3M and could result in serious injury or death.

This system is only to be used by trained users in workplace applications.

! WARNING

This Pre-Engineered Rescue System is intended for use as part of a complete personal fall protection and/or rescue system. It is expected that all users be fully trained in the safe installation and operation of their Pre-Engineered Rescue System. Misuse of this system could result in serious injury or death. For proper selection, operation, installation, maintenance, and service, refer to these User Instructions and all manufacturer recommendations, see your supervisor, or contact 3M Technical Service.

• To reduce the risks associated with working with a Pre-Engineered Rescue System which, if not avoided, could result in serious injury or death:

- Inspect the system before each use and at least annually. Inspect in accordance with the User Instructions.

- If inspection reveals an unsafe or defective condition in the device or a component of the device, remove the device from service and repair or replace according to the User Instructions.

- Label the system ‘UNUSABLE’ and immediately remove the system from service if it has been subjected to fall arrest or impact force. Inspect and handle the system according to the User Instructions.

- Ensure the rescue system and lifeline are kept free from all obstructions including, but not limited to, entanglement with other workers, yourself, and surrounding objects.

- Follow all manufacturer recommendations when connecting a lifeline.

- When performing rescue operations, always utilize fall protection safety measures as determined by your workplace rescue plan.

- Do not touch parts of devices exposed to high friction during or after long descents, as these parts may get hot and cause burns.

- Ensure proper edge protection is used if the lifeline may contact sharp edges or corners.

- Ensure a clear descent path, and that the landing area is clear of any obstructions or hazards that you may contact.

- Ensure that systems/subsystems assembled from components made by different manufacturers are compatible and meet the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements. Always consult a Competent and/or Qualified Person before using these systems.

- (AUTOMATIC DESCENT DEVICES) Only use in rescue applications.

- (AUTOMATIC DESCENT DEVICES) Always record usage as defined by the User Instructions and remove from service in accordance with usage limits listed in the User Instructions.

- (ROPE LIFELINE SYSTEMS) Use only rope described and approved in the User Instructions.

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height.

Consult with your doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or suitability of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections. Consult 3M prior to using this equipment in combination with components or subsystems other than those described in the User Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures, chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or the fall protection equipment.

- Use Arc Flash or Hot Works systems when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the fallen worker for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an unintended fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.

EN

; Prior to installation and use of this equipment, record the product identification information from the ID label in the Inspection and Maintenance Log (Table 2) at the back of this manual.

; Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M Technical Services for updated instruction manuals.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA® Rollgliss™ R550 Rescue & Escape Device (R550 Device). The R550 Device is a rescue device that is intended to lower one or two people simultaneously from an elevated height to a lower level in a rescue situation.

Figure 2 illustrates components of the R550 Device. See Table 1 for Component Specifications. The body of the R550 Device is comprised of the Housing Assembly (A). The Rope Sheave (B) is held within the Housing Assembly and ensures smooth operation of the Lifeline (C). The Anchor Loop (D) secures the Carabiner (E) to the top of the system, in addition to modular components; in conjunction, the two components secure the R550 Device to an anchorage point. The Thimble (F) of the Lifeline secures the Snap Hooks (G), which connect to the harness of the user. The Rescue Hub (H) is attached to the Housing Assembly and facilitates rescue applications for the 3327XXX series of R550 Device models.

Table 1 – Specifications

System Specifications:

Product Models: See Figure 1 for a full list of models covered by these user instructions. The last three digits of the Model Number (A), signified by ‘XXX’, indicate the maximum length (L) in meters.

Capacity: The capacity of the R550 Device depends upon the number of users, the total weight of those users, the distance to be traveled, and the number of times the device has been used to maximum descent distance previously.

Users Total Weight (including tools, clothing, etc.)

Maximum Descent Distance

Number of Descents of

Maximum Descent Distance

2 Persons 130 lb. - 620 lb. (59 kg - 282 kg) 574 ft. (175 m) 2

1 Person 130 lb. - 310 lb. (59 kg - 141 kg) 1,640 ft. (500 m) 11

1 Person 130 lb. - 220 lb. (59 kg - 100 kg) 1,640 ft. (500 m) 16

1 Person 130 lb. - 165 lb. (59 kg - 75 kg) 1,640 ft. (500 m) 22

Maximum Recommended Lifting Capacity and Height

1 Person: 141 kg for a distance of 100 m 2 Persons: 282 kg for a slight distance for rescue only.

Anchorage Strength: The structure to which the R550 Device is mounted must be capable of sustaining force in the anticipated direction(s) of loading. Each Anchorage Point location must be capable of sustaining the following values:

ANSI 3,100 lb. (1406 kg)

When more than one R550 Device is attached to an anchorage the strengths stated above must be multiplied by the number of descent devices attached to the anchorage. The R550 Device should not be attached to an Anchorage Connector if such an attachment would reduce the strength of the anchorage below requirements. See the manufacturer instructions of your Anchorage Connector for more information.

Service Temperature -40°F (-40°C) Minimum Service Temperature

Anchorage Connector Breaking Strength:

5,000 lbf (22.2 kN) Minimum Breaking Strength

Standards: The R550 Device has been tested in accordance with the standards identified on the front cover of these user instructions.

Weight: See Figure 1 for the weight (W) of each product model.

Component Specifications:

Figure 2 Reference Component Materials

A Housing Assembly Aluminum/Steel

B Rope Sheave Aluminum

C Lifeline 3/8” nylon rope

D Anchor Loop Stainless steel

E Carabiner Steel (2000112)

F Thimble Plastic; 3/8” nylon rope

G Snap Hook Steel (9502116)

H Rescue Hub Nylon

Table 1 – Specifications

Performance Specifications:

Minimum Descent Load: 130 lb. (59 kg)

Maximum Allowed Descent Height: 1 Person: 1,640 ft. (500 m) when system length permits 2 Persons: 574 ft. (175 m) when system length permits

Nominal Descent Speed: 1 Person: 2.0 ft/s - 3.0 ft/s (0.6 m/s - 0.9 m/s) 2 Persons: 2.0 ft/s - 4.0 ft/s (0.6 m/s - 1.2 m/s)

Number of Descents: 1 Person: 60 2 Persons: 20

Maximum Consecutive Descents:

The Maximum Number of Consecutive Descents is equal to the Total Cumulative Descent Distance divided by the Descent Height. Total Cumulative Descent Distances for various weight limitations are as follows:

2 Persons up to 620 lb. (282 kg) 1,148 ft. (350 m)

1 Person up to 310 lb. (140 kg) 18,044 ft. (5,500 m)

1 Person up to 220 lb. (100 kg) 25,443 ft. (7,755 m)

1 Person up to 165 lb. (75 kg) 36,089 ft. (11,000 m)

Descent Energy Rating:

The Descent Energy Rating of your R550 Rescue & Escape Device is a calculable measure of wear on your device. Factors influencing Descent Energy Rating include user weight, descent height, the number of previous descents, and the number of simultaneous users. The Descent Energy Rating is the Descent Energy Classification of your R550 Rescue and Escape Device per the respective standard. If your device exceeds this number, it must be removed from service immediately and managed according to the specifics of Section 4.1. The Maximum Descent Energy Rating of your R550 Rescue & Escape Device is determined by the number of users and the applicable standard for use:

Standard Number of Simultaneous Users

Descent Energy Rating

ANSI Z359.4 One user 300,000 ft-lb (406,750 joules)

CSA Z259.3-12

(Type 1, Class A)

One user 5,531,700 ft-lb (7,500,000 joules)

CSA Z259.3-12

(Type 1, Class C)

Two users 368,700 ft-lb (500,000 joules)

; All users must weigh no more than 140 kg (310 lb.) each.

At any time, the Descent Energy Rating of your R550 Device must not exceed this value. Descent Energy Rating can be calculated with the following equation:

E = W x H x N

Where “E” is the Descent Energy Rating in foot-pounds (ft-lb), “W” is the User Weight in pounds (lb.), “H” is the Descent Height in feet (ft.), and “N” is the total number of descents your R550 Device has experienced.

If, at any time, your R550 Device has a Descent Energy Rating (E) equal to or greater than the Maximum Descent Energy Rating, it must be removed from service immediately and marked “DO NOT USE”.

For metric units, the following equation should be used instead:

E = W x H x N x G

Where “E” is the Descent Energy Rating in Newton-meters (N-m), “W” is the User Weight in kilograms (kg), “H” is the Descent Height in meters (m), “N” is the total number of descents your R550 Device has experienced, and “G” is the acceleration due to gravity (9.81 m/s2).

Shorter length configurations will take a greater number of descents to reach the descent energy ratings of the unit. In these instances, the rope may become the limiting factor. Guidance on the number of descents based on rope life is listed above.

Unit service should be based on both the descent energy capacity and the rope life, whichever is reached first based on configuration and use.

1.0 PRODUCT APPLICATION

1.1 PURPOSE: The R550 Rescue & Escape Device is intended to lower one or two people simultaneously from an elevated height to a lower level in a rescue situation. Multiple people may descend one after another using the device. The descent speed is automatically limited during descent. Models incorporating a hand wheel allow for raising persons a short distance to facilitate rescue.

; Rescue Only: This device is for use in rescue situations only. Do not connect Lifting Equipment to the R550 Rescue & Escape Device and do not use the device for any purpose other than for rescue.

1.2 STANDARDS: Your R550 Rescue & Escape Device conforms to the national or regional standard(s) identified on the front cover of these instructions. If this product is resold outside the original country of destination, the re-seller must provide these instructions in the language of the country in which the product will be used.

1.3 SUPERVISION: Use of this equipment must be supervised by a Competent Person1.

1.4 TRAINING: This equipment must be installed and used by persons trained in its correct application. This manual is to be used as part of an employee training program as required by national, state, and/or regional regulations. It is the responsibility of the users and installers of this equipment to ensure they are familiar with these instructions, trained in the correct care and use of this equipment, and are aware of the operating characteristics, application limitations, and consequences of improper use of this equipment.

1.5 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and the means at hand to implement and communicate that plan to users, authorized persons2, and rescuers3. A trained, on-site rescue team is recommended. Training should be provided on a periodic basis to ensure rescuer proficiency. Team members should be provided with the equipment and techniques necessary to perform a successful rescue. Rescuers should be provided with these User Instructions.

1.6 INSPECTION FREQUENCY: The R550 Rescue & Escape Device shall be inspected by the user before each use and, additionally, by a competent person other than the user at intervals of no longer than one year.4 Inspection procedures are described in the “Inspection and Maintenance Log” (Table 2). Results of each Competent Person inspection should be recorded on copies of the “Inspection and Maintenance Log”.

1.7 AFTER A FALL: If the R550 Rescue & Escape Device is subjected to the forces of arresting a fall, it must be removed from service immediately, clearly marked “DO NOT USE”, and then either destroyed or forwarded to 3M for replacement or repair.

2.0 SYSTEM REQUIREMENTS

2.1 ANCHORAGE: The structure on which the R550 Rescue & Escape Device is placed or mounted must meet the Anchorage specifications defined in Table 1.

2.2 DESCENT PATH AND LANDING AREA CLEARANCE: The planned descent path must be unobstructed. The landing area must be clear of obstructions to permit safe landing of the user. Failure to provide an unobstructed descent path and landing area may result in serious injury. Maintain a minimum distance of 1.0 ft. (31 cm) away from any vertical surface to ensure safe descent.

2.3 HAZARDS: Use of this equipment in areas with environmental hazards may require additional precautions to prevent injury to the user or damage to the equipment. Hazards may include, but are not limited to: heat, chemicals, corrosive environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or overhead materials that may fall and contact the user or device. Contact 3M Technical Services for further clarification.

2.4 SHARP EDGES: Avoid using this equipment where system components will be in contact with, or scrape against, unprotected sharp edges and abrasive surfaces. An Edge Protector (Figure 5) or protective padding must be used when descending over sharp edges or abrasive surfaces.

2.5 COMPONENT COMPATIBILITY: 3M equipment is designed for use with 3M approved components and subsystems only. Substitutions or replacements made with non-approved components or subsystems may jeopardize compatibility of equipment and may affect the safety and reliability of the complete system.

2.6 CONNECTOR COMPATIBILITY: Connectors are considered to be compatible with connecting elements when they have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbf (22.2 kN). Connectors must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.

Non-compatible connectors may unintentionally disengage (see Figure 3). Connectors must be compatible in size, shape, and strength. If the connecting element to which a snap hook or carabiner attaches is undersized or irregular in shape, a situation could occur where the connecting element applies a force to the gate of the snap hook or carabiner (A). This force may cause the gate to open (B), allowing the snap hook or carabiner to disengage from the connecting point (C).

1 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

2 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.

3 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

4 Inspection Frequency: Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the frequency of competent person inspections.

2.7 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all connectors are fully closed and locked.

3M connectors (snap hooks and carabiners) are designed to be used only as specified in each product’s user’s instructions.

See Figure 4 for examples of inappropriate connections. Do not connect snap hooks and carabiners:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the snap hook complies is equipped with a 3,600 lbf (16 kN) gate. Check the marking on your snap hook to verify that it is appropriate for your application.

C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the anchor, and without visual confirmation seems to be fully engaged to the anchor point.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the lanyard and connector specifically allows such a connection).

F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that roll-out could occur.

G. In a manner that does not allow the connector to align properly while under load.

3.0 INSTALLATION

; Installation of the Rollgliss™ R550 Rescue & Escape Device must be supervised by a Qualified Person1. The installation must be certified by a Competent Person as meeting the criteria for a Certified Anchorage, or that it is capable of supporting the potential forces that could be encountered during a fall.

3.1 PLANNING: Plan your R550 Device and how it will be used before starting your work. Account for all factors that may affect your safety before, during and after a fall. Consider all requirements, limitations and specifications defined in Section 2 and Table 1.

3.2 INSTALLING THE R550 REScuE & EScAPE DEvIcE: The R550 Device may be connected to an anchorage or to a fixed ladder. Ensure that the R550 Device is properly installed before use, according to the following procedures:

; When connecting the R550 Device to an Anchorage, confirm that the connection arrangement will not block or restrict a descent.

• connecting the R550 Device to an Anchorage: See Figure 6 for examples of connection of the R550 Descender to an anchorage. See Section 2 for compatibility and anchorage strength requirements.

A Anchorage

B Anchorage Connector

C Carabiner

D Web Lanyard

E Anchorage Connector (Web Sling)

• connecting the R550 Device to a Fixed Ladder: See Figure 7 for an example of attachment of the R550 Descender to the rungs of a fixed ladder using a 3M Ladder Bracket accessory. The R550 Device mounts on the Ladder Bracket by fitting the lower eye of the R550 over the pin on the Ladder Bracket and inserting the Ball Lock Pin through mounting holes in the R550 Anchor Loop and Ladder Bracket. R550 Descenders mounted with the Ladder Bracket still require that the unit be secured by the anchorage handle to an anchorage of sufficient strength. See Section 2 for anchorage strength requirements.

A Anchorage

B Anchorage Connector (Web Sling)

C Carabiner

D Ball Lock Pin

E Fixed Ladder

F Ladder Rungs

G Ladder Bracket

• Preparing the Lifeline: Lower one end of the lifeline to the ground or landing below. Ensure that the lifeline is free of knots or kinks.

4.0 USE

4.1 BEFORE EAcH uSE: Verify that your work area and Personal Fall Arrest System (PFAS) meet all criteria defined in Section 2 and that a formal Rescue Plan is in place. Inspect the R550 Rescue & Escape Device per the ‘User’ inspection points defined on the “Inspection and Maintenance Log” (Table 2). Confirm that the Descent Energy Rating of the device does not exceed the values in Table 1. If inspection reveals an unsafe or defective condition, or if the device exceeds the Maximum Descent Energy Capacity, do not use the device. Remove the device from service and destroy, or contact 3M regarding replacement or repair.

4.2 REScuE APPLIcATIONS: The R550 Rescue & Escape Device may be used for rescue applications according to the following methods:

; Do not use a body belt with this equipment. Body belts do not support your entire body, which may result in serious injury.

; Users of this equipment must be in good physical condition. The user must have the ability to absorb the landing.

; Always wear gloves when handling the lifeline to control descent speed.

SINGLE-PERSON uNASSISTED EScAPE: Procedures for performing an unassisted descent with the R550 Rescue System are as follows:

1. connect to a Full Body Harness or other Body Support (Figure 8): A full body harness or other means of supporting the user must be used with the R550 Device. Do not use a body belt with this device. When using a full body harness, connect the Snap Hook on the lifeline to the sternal D-ring (A) or dorsal D-ring (B). Ensure the D-ring is positioned to hold the user upright. See the full body harness manufacturer’s instructions for more information.

2. Prepare the Lifeline for Descent: Prior to descent, the section of lifeline between the user and the R550 Device must be tightened to remove any slack. Tighten the lifeline by pulling on the free end of the rope until slack between the user and R550 Device is removed. Once the lifeline is taut, hold the free end of the lifeline tightly until descent is initiated.

3. Descend to Safety: Release the free end of the lifeline to initiate descent. Descent speed will be automatically controlled to a rate described in Table 1 by the R550 Device’s centrifugal brake. Descent may be slowed, interrupted or prevented by using the following methods (see Figure 10):

1: Slow or interrupt descent by firmly grasping the free end of the Lifeline (A).

2: Use the Pigtail (B) while firmly grasping the free end of the Lifeline (A) to provide additional descent control.

3: Prevent unintentional descent by securing the free end of the Lifeline (A) with the Pigtail (B) and Cam Cleats

(C). Bend your knees to prepare for landing. After landing, disconnect the lifeline from the body support.

; The R550 Device may become hot during use which could injure the user if parts other than those used to control the descent are touched. Use beyond the specified load and descent length limits may generate excessive heat which could damage the descent line.

4. Prepare for the Next Descent: After use of the R550 Device, the lifeline must be pulled through the device as needed to position a lifeline end and Snap Hook adjacent to the next person to descend.

REMOTE ASSISTED REScuE: See Figure 9.1 for reference. The R550 Device is equipped with a Rescue Hub (RH) which can be used in remote assisted rescues to raise the fall victim to permit removal of their fall arrest subsystem (lanyard, etc.) prior to descent to safety. Procedures are as follows:

; During a rescue, there should be direct or indirect visual contact or some other means of communication with the fall victim at all times during the rescue process.

1. Lower or Raise One End of the Lifeline to the victim: Pull the lifeline (L) through the R550 Device (A) as needed until the snap hook (B) on one end of the lifeline is adjacent to the desired connection point on the victim’s body support (C).

2. connect to the victim’s Full Body Harness or other Body Support: Connect the snap hook (B) on the rescue end of the lifeline to the sternal D-ring or dorsal D-ring (C) (also see Figure 14 for D-ring locations). Ensure the D-ring is positioned to hold the user upright.

; In the event the connection point on the victim’s body support is not within reach, the rope grab accessory (Figure 9.3, D) can be attached upside down (ò) on the victim’s lanyard (VL) and locked in place. The snap hook on the R550 lifeline (L) can be attached to the eye (E) on the rope grab (D) and the rescue hub (RH) can be used to raise the victim to safety or to a point where their initial fall protection system can be released to allow lowering the victim to safety.

3. Raise the victim to Disconnect the Fall Arrest Subsystem: Rotate the Rescue Hub (RH) to raise the victim’s weight from the fall arrest subsystem and onto the R550 Device. Secure the Free End of the lifeline with the R550 Device’s Pigtail and Cam Cleats to prevent unintentional descent (see Figure 10). Disconnect the Victim’s fall arrest subsystem (lanyard, etc.).

• Alternate Option (Figure 11): The R550 Device is also configured to allow a Power Drill (minimum 0.5 in.

chuck and 400 lbf-in. torque) to be attached to the center of the Rescue Hub which can be used in remote assisted rescues to raise the fall victim. (See Table 1 for an example of lifting distances.) Attach the Power Drill directly to the shaft at the center of the Rescue Hub (see Figure 10). Use the attached Power Drill to rotate the Rescue Hub to raise the victim’s weight from the fall arrest subsystem and onto the R550 Device. Secure the Free End of the lifeline with the R550 Device’s Pigtail and Cam Cleats to prevent unintentional descent (see Figure 10). Detach the Power Drill by lowering the victim’s weight onto the unit’s Pigtail and Cam Cleats and then releasing the Power Drill from the center of the Rescue Hub. Once the Powered Drill is removed, disconnect the victim’s fall arrest subsystem (lanyard, etc.).

Table 1: Single Battery Lifting Distances in either direction for DeWalt 18V Drill (Model DCD990M2)

Low Speed Medium Speed High Speed

220 lb. (100 kg) Load 250 ft. (76 m)* 250 ft. (76 m)* 175 ft. (53 m)*

310 lb. (140 kg) Load 200 ft. (61 m)* 150 ft. (46 m)* NA**

* Lifting distance based on full battery charge, ambient temperature of 72°F (22°C).

** High speeds with high loads not recommended.

; Power Drill lifting capabilities will vary with victim load, battery charge, drill model, and environmental conditions. The lowest drill speed setting is recommended to maximize battery life and to reduce the risk of damaging the drill or the R550 Descender. Loads greater than 310 lb. (140 kg) should not be lifted with the Power Drill option. Lifting in reverse direction will typically decrease the lifting distance capacity of a single battery charge.

4. Prepare the Lifeline for Descent: Prior to descent, the section of lifeline between the user and the R550 Device must be tightened to remove any slack. Tighten the lifeline by pulling on the free end of the lifeline until slack between the user and R550 Device is removed. Once the lifeline is taut, hold the free end of the lifeline tightly until descent is initiated.

5. Descend to Safety: Release the free end of the lifeline to initiate descent. Descent speed will be automatically controlled to a rate described in Table 1 by the R550 Device’s centrifugal brake. Descent may be interrupted by firmly grasping the free end of the lifeline (see Figure 10). Bend your knees to prepare for landing. After landing, disconnect the lifeline from the body support. Record all descents in the Descent Log (Table 3).

; The R550 Rescue & Escape Device may become hot during use which could injure the user if parts other than those used to control the descent are touched. Use beyond the specified load and descent length limits may generate excessive heat which could damage the descent line.

SIMuLTANEOuS REScuE AND EScAPE: See Figure 9.2. In situations where the fall victim requires assistance, simultaneous rescue and escape allows a rescuer to accompany the victim during descent:

; During a rescue, there should be direct or indirect visual contact or some other means of communication with the fall victim at all times during the rescue process.

; Two-person descents with the R550 Device should not exceed a total combined weight (including tools, clothing, body support, etc.) of 620 lb. (282 kg) and a descent distance of 574 ft. (175 m).

1. Descend to the victim: In situations where the fall victim is suspended by their existing fall arrest subsystem, it will be necessary for the rescuer to descend to the victim’s location to provide assistance. Descend to the victim per the steps in Section 4.2 - “Single Person Unassisted Escape”.

; When the victims position is reached, descent can be interrupted by firmly grasping and holding the free end of the rope (see Figure 10). If a secondary rescuer is available at the R550 Device, the free end of the rope can be passed through the pigtail and then secured in the cam cleats to prevent unintentional descent while the primary rescuer is securing the victim.

2. connect the victim to the R550 Device: Connect a rescue lanyard (RL) (or similar equipment) between the lifeline snap hook connected to the rescuer’s full body harness front D-ring (RD) or the back D-ring on the victim’s full body harness (C).

; Do not use a body belt with this equipment. Body belts do not support your entire body, which may result in serious injury.

3. Disconnect the victim’s Fall Arrest Subsystem: Ensure that the victim is securely attached to the R550 Device and then detach the victim’s fall arrest subsystem (lanyard, etc.) to free the victim for descent.

; If a secondary rescuer is available at the R550 Rescue & Escape Device, the Rescue Hub can be used to raise the victim slightly for detachment of their fall arrest subsystem.

4. Descend to Safety: Release the free end of the lifeline to initiate descent. Descent speed will be automatically controlled to a rate described in Table 1 by the R550 Device’s centrifugal brake. Descent may be interrupted by firmly grasping the free end of the lifeline (see Figure 10). Bend your knees to prepare for landing. After landing, disconnect the lifeline from the body support. Record all descents in the Descent Log (Table 3).

; The R550 Device may become hot during use which could injure the user if parts other than those used to control the descent are touched. Use beyond the specified load and descent length limits may generate excessive heat which could damage the descent line.

4.3 AFTER A REScuE: The R550 Device must be removed from service following use in a rescue event. The R550 Device should then be destroyed or sent to an authorized service center for inspection and repair. See Section 5.3 for more information.

5.0 INSPECTION

5.1 INSPEcTION FREQuENcY: The R550 Device must be inspected at the intervals defined in Section 1. Additionally, the R550 Device must be sent to an authorized service center for inspection and service every five years. See Section 5.3 for more information. Inspection procedures are described in the “Inspection and Maintenance Log” (Table 2). Inspect all other components of the Fall Protection System per the frequencies and procedures defined in the manufacturer’s instructions.

; Humidity Resistant Case Inspection: If the R550 Device is stored continuously in a Humidity Resistant Case (see Figure 12), monthly and yearly inspections are not required and the device may be sent to an authorized service center at intervals not to exceed ten years. In addition to inspection prior to each use, the Humidity Indicator on the case (see Figure 12) should be inspected annually and the date and inspector’s initials logged on the Case Inspection Label. If the Humidity Indicator displays a reading of 60 or greater (Pie Sector Indicator), the case should be removed from service and the contents inspected per the procedures defined in the “Inspection and Maintenance Log” (Table 2).

5.2 DEFEcTS: If inspection reveals an unsafe or defective condition, remove the R550 Device from service immediately and label “DO NOT USE”. Do not attempt to repair the device.

5.3 REcERTIFIcATION: After it has been removed from service, or at least every five years (excluding humidity resistant case storage), the R550 Device must be sent to an authorized service center for thorough inspection, maintenance, and recertification.

5.4 PRODucT LIFE: The functional life of the R550 Device is determined by work conditions and maintenance. As long as the product passes inspection criteria, it may remain in service.

6.0 MAINTENANCE, SERVICING, STORAGE

6.1 cLEANING: Periodically clean the R550 Device’s metal components with a soft brush, warm water, and a mild soap solution. Ensure parts are thoroughly rinsed with clean water.

6.2 SERvIcE: Only 3M or parties authorized in writing by 3M may make repairs to this equipment. If the R550 Device has been subject to fall force or inspection reveals an unsafe or defective conditions, remove the system from service and destroy.

6.3 STORAGE AND TRANSPORT: When not in use, store and transport the R550 Device in a cool, dry, clean environment out of direct sunlight. Avoid areas where chemical vapors may exist. Thoroughly inspect the device after extended storage. If the R550 Device cannot be stored in a properly suitable environment, a Humidity Resistant Case should be used.

; R550 Devices installed at a workstation and left in place between inspections should be adquately protected from environmental conditions.

7.0 RFID TAG

7.1 LOcATION: 3M product covered in these user instructions is equipped with a Radio Frequency Identification (RFID) Tag.

RFID Tags may be used in coordination with an RFID Tag Scanner for recording product inspection results. See Figure 14 for where your RFID Tag is located.

7.2 DISPOSAL: Prior to disposing of this product, remove the RFID Tag and dispose/recycle in accordance with local regulations. For more information, please visit our website: http://www.3M.com/FallProtection/RFID

8.0 LABELS and MARKINGS

8.1 LABELS: Figure 15 illustrates labels present on the R550 Device. Labels must be replaced if they are not present and fully legible. Information provided on each label is as follows:

A Refer to Table 1.

B Refer to Section 5.

C Manufactured (Year/Month)

D System Length (meters, feet)

E Model Number

F Lot Number

G Read all user instructions.

H Avoid descending into electrical, thermal, chemical, or other hazards. Use only the rope provided by 3M as part of this system. See User Manual for additional information.

I Maximum lifting weight and height.

J Maximum single user descent weight and height.

K Maximum two user descent weight and height.

L Applicable Standards

Table 2 – Inspection and Maintenance Log Inspection Date: Inspected By:

Component: Inspection: (See Section 2 for Inspection Frequency) User Competent

Person

R550 Device (Figure 2)

Inspect for loose fasteners and bent or damaged parts.

Inspect the Housing Assembly (A), Rope Sheave (B), Anchor Loop (D), Thimble (F), and Rescue Hub (H) for distortion, cracks, or other damage.

If the R550 Device is stored in a Humidity Resistant Case, inspect the Humidity Indicator on the outside of the case (see Figure 12). If the Humidity Indicator displays a reading of 60 or greater (pie sector indicator): (1) Open the case and inspect the R550 Device per the remaining steps. (2) Maintain the case as described in Section 6.1.

Ensure the Lifeline (C) pulls through the device smoothly. Inspect the entire rope for cuts, burns, severely abraded areas, and excessive wear.

Inspect the Carabiner (E) and Snap Hooks (G) for damage, corrosion, and working condition.

Inspect the entire unit for signs of corrosion.

Labels (Figure 15)

Ensure that all labels are present and fully legible.

PFAS and Other Equipment

Additional Personal Fall Arrest System (PFAS) equipment (harness, SRD, etc) that are used with the Anchorage System should be installed and inspected per the manufacturer’s instructions.

Structure Verify the structure to which the structure is attached meets the strength requirements from Table 1 in all possible directions of loading.

Serial Number(s): Date Purchased:

Model Number(s): Date of First Use:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Corrective Action/Maintenance: Approved By: Next Inspection Due:

Date:

Table 3 – Descent Log

Serial Number(s): Date Purchased:

Model Number: Date of First Use:

Date Descent Weight Descent Distance Cumulative Descent Distance Total of Descent Distances at left since last Service Date (below).

1. Match the greatest Descent Weight logged above with the appropriate Weight Limit in the table below to determine the allowed Maximum Cumulative Descent Distance.

Weight Limits Max. Cumulative Descent Distance 2 Persons up to 620 lb. (282 kg) 1,148 ft. (350 m)

1 Person up to 310 lb. (140 kg) 18,044 ft. (5,500 m)

1 Person up to 220 lb. (100 kg) 25,443 ft. (7,755 m)

1 Person up to 165 lb. (75 kg) 36,089 ft. (11,000 m)

2. If the Cumulative Descent Distance calculated above meets or exceeds the Maximum Cumulative Descent Distance from Step 1, the Anchorage Connector should be serviced by an Authorized Service Center.

Service Dates should be logged below:

Service Date Service Date

Nº DE FORMULAIRE : 5908259 RÉV. : A 18

INFORMATION DE SÉCURITÉ

Veuillez lire, comprendre et suivre toutes les informations de sécurité contenues dans ces instructions avant d’utiliser cet équipement de sauvetage conçu à l'avance. LE NON-RESPECT DE CES INSTRUCTIONS PEUT ENTRAÎNER DES BLESSURES

GRAVES, VOIRE LA MORT.

Ces instructions doivent être transmises à l’utilisateur de cet équipement. Veuillez conserver ces instructions pour une utilisation ultérieure.

Utilisation prévue :

Cet équipement de sauvetage conçu à l'avance est prévu pour être utilisé comme partie intégrante d’un système de protection antichute personnel complet ou d'un système de sauvetage.

L’utilisation dans le cadre d’autres applications comme, sans en exclure d’autres, des activités récréatives ou liées au sport, ou d’autres activités non décrites dans les instructions destinées à l’utilisateur, n’est pas approuvée par 3M et peut entraîner des blessures graves voire la mort.

Ce système doit être utilisé uniquement par des usagers formés sur les applications du lieu de travail.

! AVERTISSEMENT

Cet équipement de sauvetage conçu à l'avance est prévu pour être utilisé comme partie intégrante d’un système de protection antichute personnel complet ou d'un système de sauvetage. Il est attendu que tous les utilisateurs sont entièrement formés sur l’installation et le fonctionnement sécuritaires de leur système de sauvetage conçu à l'avance. Une mauvaise utilisation de ce système peut entraîner des blessures graves, voire la mort. Pour s'assurer d'un choix, d'un fonctionnement, d'une installation, de travaux d'entretien et de réparation appropriés, reportez-vous à ces instructions de l'utilisateur ainsi qu’à toutes les recommandations du fabricant, consultez votre superviseur ou communiquez avec les services techniques de 3M.

• Pour réduire les risques associés au travail avec un système de sauvetage conçu à l'avance qui, s’ils ne sont pas évités, pourraient entraîner de graves blessures, voire la mort :

- Inspectez le système avant chaque utilisation et au moins une fois par année. Réalisez l'inspection conformément aux instructions de l'utilisateur.

- Si l’inspection révèle l’existence d’une défectuosité ou d'une condition non sécuritaire du dispositif ou d'un composant du dispositif, mettez le dispositif hors service et faites-le réparer ou remplacez-le conformément aux instructions de l'utilisateur.

- Si le système a subi une force d’impact ou a dû arrêter une chute, apposez-lui une étiquette « INUTILISABLE » et mettez-le immédiatement hors service. Inspectez et manipulez le système conformément aux instructions de l'utilisateur.

- Veillez à ce que le système de sauvetage et la corde d'assurance soient dégagés de tout obstacle, notamment de l'emmêlement avec d'autres travailleurs, vous-même et les objets environnants.

- Suivez toutes les recommandations du fabricant au moment de connecter une corde d'assurance.

- Au moment de réaliser des opérations de sauvetage, utilisez toujours des mesures de sécurité pour la protection antichute comme le précise votre plan de sauvetage en milieu de travail.

- Ne touchez pas aux pièces de dispositifs exposés à une friction élevée durant ou après une longue descente, car ces pièces risquent d'être chaudes et de causer des brûlures.

- Assurez-vous de protéger la corde d'assurance si celle-ci entre en contact avec des bords tranchants ou des coins.

- Assurez-vous que la trajectoire de descente est dégagée et que l’aire de réception est libre de tout obstacle ou de tout danger éventuel.

- Assurez-vous que les systèmes/sous-systèmes assemblés à partir de composants fabriqués par différents fabricants sont compatibles aux normes applicables et satisfont à leurs exigences, y compris la norme ANSI Z359 ou d'autres codes, normes ou exigences de protection antichute applicables. Consultez toujours une personne qualifiée avant d'utiliser ces systèmes.

- (DISPOSITIFS DE DESCENTE AUTOMATIQUE) Uniquement utilisés dans des applications de sauvetage.

- (DISPOSITIFS DE DESCENTE AUTOMATIQUE) Consignez toujours l'utilisation comme le précisent les instructions de l'utilisateur, et mettez le dispositif hors service conformément aux limites d'utilisation indiquées dans les instructions de l'utilisateur.

- (DISPOSITIFS R550 AVEC VOLANT DE COMMANDE) Assurez-vous que l'opérateur a toujours la maîtrise du volant de commande lorsque le système est sous charge.

- (SYSTÈMES À CORDE D'ASSURANCE) Utilisez uniquement la corde décrite et approuvée dans les instructions de l'utilisateur.

• Pour réduire les risques associés au travail en hauteur qui, s’ils ne sont pas évités, pourraient entraîner des blessures graves, voire la mort :

- Assurez-vous que votre condition physique et votre état de santé vous permettent de supporter en toute sécurité toutes les forces associées au travail en hauteur. Consultez votre médecin en cas de questions sur votre capacité à utiliser cet équipement.

- Ne dépassez jamais la capacité maximale permise de votre équipement de protection antichute.

- Ne dépassez jamais la distance maximale de chute libre de votre équipement de protection antichute.

- N’utilisez jamais un équipement de protection antichute qui échoue à une inspection préalable à son utilisation ou à toute autre inspection programmée ou encore si vous vous inquiétez de l’utilisation ou de la pertinence de l’équipement pour votre application. En cas de questions, n’hésitez pas à communiquer avec les services techniques de 3M.

- Certaines combinaisons de sous-systèmes et de composants peuvent gêner le fonctionnement de cet équipement. N’utilisez que des connecteurs compatibles. Consultez 3M avant d’employer cet équipement conjointement avec des composants ou des sous-systèmes autres que ceux décrits dans les instructions à l’utilisateur.

- Prenez des précautions supplémentaires lorsque vous travaillez à proximité d’une machinerie mobile (p. ex. l’entraînement supérieur d’une plateforme pétrolière), en présence de risques électriques, de températures extrêmes, de risques chimiques, de gaz explosifs ou toxiques, de bords tranchants ou de matériaux en hauteur pouvant tomber sur vous ou votre équipement de protection antichute.

- Lorsque vous travaillez dans un environnement où la chaleur est élevée, utilisez des systèmes dont l’usage est prévu pour des travaux à haute température ou en présence d’arc électrique.

- Évitez les surfaces et les objets qui pourraient endommager l’équipement de l’utilisateur.

- Lorsque vous travaillez en hauteur, vérifiez d’abord que la distance d’arrêt est adéquate.

- Ne modifiez jamais votre équipement de protection antichute. Seules 3M ou les parties autorisées par écrit par 3M sont en droit d’effectuer des réparations sur cet équipement.

- Avant d’utiliser un équipement de protection antichute, assurez-vous qu’un plan de sauvetage est en place et permet un sauvetage rapide en cas de chute.

- Si un tel incident devait se produire,…