MLS Village Library_Addendum-001.pdf

5909 NW Expressway, Suite 600 Oklahoma City, Oklahoma 73132 T 405 722 7270 F 405 722 8373 W www.lwpb.com

ADDENDUM No. 1

Metropolitan Library System Village Library Renovation

December 3, 2018

NOTICE: The following additions and corrections are hereby made to the Contract Documents for the project. The Bidders must acknowledge receipt of all addenda on the space on the Bid Form.

This Addendum consists of (16) sixteen - 8 ½” x 11” written pages.

GENERAL

A. Permit costs are the responsibility of the Contractor (reference Section 00 5200 Agreement Form and attached DRAFT AIA Document A015, Standard Short Form of Agreement Between Owner & Contractor). Standard fee schedules for City of the Villiage are available at: http://wwwnew.thevillageok.org/wp-content/uploads/2018/06/Fee-Schedules-.pdf

B. Clarification: at new, interior book drop (refer plans), any mobile book bins or carts will be provided by Owner, and are not the responsibility of the Contractor.

DRAWINGS

A. Reference drawing sheet A2.3 LEGENDS & SCHEDULES:

Revise – General notes for interior doors: add the following text: “4. REFER SECTION

08 1416 FLUSH WOOD DOORS FOR BASIS-OF-DESIGN INTERIOR GLASS LITE

WITH INTEGRAL BLIND.” Reference screen shot (below).

12/03/18 http://wwwnew.thevillageok.org/wp-content/uploads/2018/06/Fee-Schedules-.pdf http://wwwnew.thevillageok.org/wp-content/uploads/2018/06/Fee-Schedules-.pdf

5909 NW Expressway, Suite 600 Oklahoma City, Oklahoma 73132 T 405 722 7270 F 405 722 8373 W www.lwpb.com

SPECIFICATIONS

A. Reference specification Section 08 1416 FLUSH WOOD DOORS.

• Replace – Section in its entirety (attachment).

• Add integral mini-blind at Door #150, basis-of-design by Air Louvers Activar, Inc.

B. Reference specification Section 08 7102 DOOR HARDWARE.

• Replace – section in its entirety (attachment).

• Provide lever handle-type design to meet ADA requirements.

C. Reference specification Section 08 8000 GLAZING

• Delete – section in its entirety.

D. Reference specification Section 09 9600 CARPET.

• Replace – section in its entirety.

• Modify paragraph 2.03.B to require full-spread, releasable adhesive at book stack areas and areas with heavy rolling traffic.

END OF ADDENDUM

PART 1 - GENERAL

1.01 RELATED DOCUMENTS

SECTION 08 7102

DOOR HARDWARE

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.

1.02 SUMMARY

A. This Section includes commercial door hardware for the following:

1. Swinging doors.

B. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.

1. ANSI A 117.1 - Accessible and Usable Buildings and Facilities.

2. FEMA P-361 2015 - Design and Construction Guidance for Community Safe Rooms.

3. ICC 500-2014, ICC/NSSA Standard for the Design and Construction of Storm Shelters.

4. ICC/IBC - International Building Code.

5. NFPA 70 - National Electrical Code.

6. NFPA 80 - Fire Doors and Windows.

7. NFPA 101 - Life Safety Code.

8. NFPA 105 - Installation of Smoke Door Assemblies.

9. State Building Codes, Local Amendments.

C. Standards: All hardware specified herein shall comply with the following industry standards:

1. ANSl/BHMA Certified Product Standards - A 156 Series

2. UL 10C - Positive Pressure Fire Tests of Door Assemblies

1.03 SUBMITTALS

A. Product Data: Manufacturer's product data sheets including installation details, material descriptions, dimensions of individual components and profiles, operational descriptions and finishes.

B. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate the final Door Hardware Schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.

1. Format: Comply with scheduling sequence and vertical format in DH l's "Sequence and

Format for the Hardware Schedule."

2. Organization: Organize the Door Hardware Schedule into door hardware sets indicating complete designations of every item required for each door or opening. Organize door hardware sets in same order as in the Door Hardware Sets at the end of Part 3. Submittals that do not follow the same format and order as the Door Hardware Sets will be rejected and subject to resubmission.

3. Content: Include the following information:

a. Type, style, function, size, label, hand, and finish of each door hardware item.

b. Manufacturer of each item.

c. Fastenings and other pertinent information.

d. Location of door hardware set, cross-referenced to Drawings, both on floor plans and in door and frame schedule.

e. Explanation of abbreviations, symbols, and codes contained in schedule.

f. Mounting locations for door hardware.

g. Door and frame sizes and materials.

h. Warranty information for each product.

i. Submittal Sequence: Submit the final Door Hardware Schedule at earliest possible date, particularly where approval of the Door Hardware Schedule must precede fabrication of other work that is critical in the Project construction schedule. Include

Metropolitan Library System 2018 - Village Library Renovation 08 7102 - 1 DOOR HARDWARE

November 19, 2018

Product Data, Samples, Shop Drawings of other work affected by door hardware, and other information essential to the coordinated review of the Door Hardware Schedule.

C. Proof of Qualification: Provide copy of manufacturer(s) Factory Trained Installer documentation indicating proof of status as a qualified installer of Windstorm assemblies.

D. Keying Schedule: After a keying meeting with the owner has taken place prepare a separate keying schedule detailing final instructions. Submit the keying schedule in electronic format.

Include keying system explanation, door numbers, key set symbols, hardware set numbers and special instructions. Owner must approve submitted keying schedule prior to the ordering of permanent cylinders/cores.

E. Informational Submittals:

1. Product Test Reports: Indicating compliance with cycle testing requirements, based on evaluation of comprehensive tests performed by manufacturer and witnessed by a qualified independent testing agency.

F. Operating and Maintenance Manuals: Provide manufacturers operating and maintenance manuals for each item comprising the complete door hardware installation in quantity as required in Division 01, Closeout Submittals.

1.04 QUALITY ASSURANCE

A. Manufacturers Qualifications: Engage qualified manufacturers with a minimum 5 years of documented experience in producing hardware and equipment similar to that indicated for this Project and that have a proven record of successful in-service performance.

B. Installer Qualifications: A minimum 3 years documented experience installing both standard and electrified door hardware similar in material, design, and extent to that indicated for this Project and whose work has resulted in construction with a record of successful in-service performance.

C. Door Hardware Supplier Qualifications: Experienced commercial door hardware distributors with a minimum 5 years documented experience supplying both mechanical and electromechanical hardware installations comparable in material, design, and extent to that indicated for this Project. Supplier recognized as a factory direct distributor by the manufacturers of the primary materials with a warehousing facility in Project's vicinity. Supplier to have on staff a certified Architectural Hardware Consultant (AHC) available during the course of the Work to consult with Contractor, Architect, and Owner concerning both standard and electromechanical door hardware and keying.

D. Windstorm Assembly Installer Qualifications: Installers are to be factory trained for shop and field installation prior to project bid, and are responsible for commissioning, servicing, and warranting the installed equipment specified for the project. A pre-installation site inspection of the frame and floor conditions shall be conducted by the factory trained installer prior to any Windstorm assembly hardware applied to the opening.

E. Source Limitations: Obtain each type and variety of door hardware specified in this section from a single source unless otherwise indicated.

1 . Electrified modifications or enhancements made to a source manufacturer's product line by a secondary or third party source will not be accepted.

F. Each unit to bear third party permanent label demonstrating compliance with the referenced standards.

G. At completion of installation, provide written documentation that components were applied to manufacturer's instructions and recommendations and according to approved schedule.

1.05 DELIVERY, STORAGE, AND HANDLING

A. Inventory door hardware on receipt and provide secure lock-up and shelving for door hardware delivered to Project site. Do not store electronic access control hardware, software or accessories at Project site without prior authorization.

B. Tag each item or package separately with identification related to the final Door Hardware Schedule, and include basic installation instructions with each item or package.

Metropolitan Library System 2018 - Village Library Renovation 08 7102 - 2 DOOR HARDWARE

C. Deliver, as applicable, permanent keys, cylinders, cores, access control credentials, software and related accessories directly to Owner via registered mail or overnight package service.

Instructions for delivery to the Owner shall be established at the "Keying Conference".

1.06 COORDINATION

A. Templates: Obtain and distribute to the parties involved templates for doors, frames, and other work specified to be factory prepared for installing standard and electrified hardware. Check Shop Drawings of other work to confirm that adequate provisions are made for locating and installing hardware to comply with indicated requirements.

B. Door and Frame Preparation: Doors and corresponding frames are to be prepared, reinforced and pre-wired (if applicable) to receive the installation of the specified electrified, monitoring, signaling and access control system hardware without additional in-field modifications.

1.07 WARRANTY

A. General Warranty: Reference Division 01, General Requirements. Special warranties specified in this Article shall not deprive Owner of other rights Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by Contractor under requirements of the Contract Documents.

B. Warranty Period: Written warranty, executed by manufacturer(s), agreeing to repair or replace components of standard and electrified door hardware that fails in materials or workmanship within specified warranty period after final acceptance by the Owner. Failures include, but are not limited to, the following:

1. Structural failures including excessive deflection, cracking, or breakage.

2. Faulty operation of the hardware.

3. Deterioration of metals, metal finishes, and other materials beyond normal weathering.

4. Electrical component defects and failures within the systems operation.

C. Standard Warranty Period: One year from date of Substantial Completion, unless otherwise indicated.

D. Special Warranty Periods:

1. Seven years for heavy duty cylindrical (bored) locks and latches.

1.08 MAINTENANCE SERVICE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 - PRODUCTS

2.01 SCHEDULED DOOR HARDWARE

A. General: Provide door hardware for each door to comply with requirements in Door Hardware Sets and each referenced section that products are to be supplied under.

B. Designations: Requirements for quantity, item, size, finish or color, grade, function, and other distinctive qualities of each type of door hardware are indicated in the Door Hardware Sets at the end of Part 3. Products are identified by using door hardware designations, as follows:

1. Named Manufacturer's Products: Product designation and manufacturer are listed for each door hardware type required for the purpose of establishing requirements. Manufacturers' names are abbreviated in the Door Hardware Schedule.

C. Substitutions: Requests for substitution and product approval for inclusive mechanical and electromechanical door hardware in compliance with the specifications must be submitted in writing and in accordance with the procedures and time frames outlined in Division 01, Substitution Procedures. Approval of requests is at the discretion of the architect, owner, and their designated consultants.

2.02 HANGING DEVICES

A. Hinges: ANSl/BHMA A 156.1 certified butt hinges with number of hinge knuckles and other options as specified in the Door Hardware Sets.

Metropolitan Library System 2018 - Village Library Renovation 08 7102 - 3 DOOR HARDWARE

1. Quantity: Provide the following hinge quantity:

a. Two Hinges: For doors with heights up to 60 inches.

b. Three Hinges: For doors with heights 61 to 90 inches.

c. Four Hinges: For doors with heights 91 to 120 inches.

d. For doors with heights more than 120 inches, provide 4 hinges, plus 1 hinge for every

30 inches of door height greater than 120 inches.

e. Hinge Size: Provide the following, unless otherwise indicated, with hinge widths sized for door thickness and clearances required:

1) Widths up to 3'0": 4-1 /2" standard or heavy weight as specified.

2) Sizes from 3'1" to 4'0": 5" standard or heavy weight as specified.

f. Hinge Weight and Base Material: Unless otherwise indicated, provide the following:

1) Exterior Doors: Heavy weight, non-ferrous, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate standard weight.

2) Interior Doors: Standard weight, steel, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate heavy weight.

g. Hinge Options: Comply with the following:

1) Non-removable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while door is closed; for the all out-swinging lockable doors.

h. Manufacturers:

1) McKinney Products; ASSA ABLOY Architectural Door Accessories (MK).

2.03 DOOR OPERATING TRIM

A. Door Push Plates and Pulls: ANSl/BHMA A 156.6 certified door pushes and pulls of type and design specified in the Hardware Sets. Coordinate and provide proper width and height as required where conflicting hardware dictates.

1. Push/Pull Plates: Minimum .050 inch thick, size as indicated in hardware sets, with beveled edges, secured with exposed screws unless otherwise indicated.

2. Fasteners: Provide manufacturer's designated fastener type as indicated in Hardware

Sets.

3. Manufacturers:

a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).

2.04 CYLINDERS AND KEYING

A. General: Cylinder manufacturer to have minimum (10) years experience designing secured master key systems and have on record a published security keying system policy.

B. Source Limitations: Obtain each type of keyed cylinder and keys from the same source manufacturer as locksets and exit devices, unless otherwise indicated.

1. Manufacturers:

a. Schlage (SC).

b. No Substitution.

C. Cylinders: Original manufacturer cylinders complying with the following:

1. Mortise Type: Threaded cylinders with rings and cams to suit hardware application.

2. Rim Type: Cylinders with back plate, flat-type vertical or horizontal tailpiece, and raised trim ring.

3. Bored-Lock Type: Cylinders with tailpieces to suit locks.

4. Mortise and rim cylinder collars to be solid and recessed to allow the cylinder face to be flush and be free spinning with matching finishes.

5. Keyway: Match Facility Standard.

D. Keying System: Each type of lock and cylinders to be factory keyed.

1. Conduct specified "Keying Conference" to define and document keying system instructions and requirements.

2. Furnish factory cut, nickel-silver large bow permanently inscribed with a visual key control number as directed by Owner.

Metropolitan Library System 2018 - Village Library Renovation 08 7102-4 DOOR HARDWARE

3. Existing System: Key locks to Owner's existing system.

E. Key Quantity: Provide the following minimum number of keys:

1. Change Keys per Cylinder: Three (3).

2. Master Keys (per Master Key Level/Group): Five (5).

3. Construction Keys (where required): Ten (10).

F. Construction Keying: Provide construction master keyed cylinders.

G. Key Registration List (Bitting List):

1. Provide keying transcript list to Owner's representative in the proper format for importing into key control software.

2. Provide transcript list in writing or electronic file as directed by the Owner.

2.05 MECHANICAL LOCKS AND LATCHING DEVICES

A. Cylindrical Locksets, Grade 1 (Heavy Duty): ANSl/BHMA A156.2, Series 4000, Grade 1 certified.

1. Furnish with solid cast levers, standard 2 3/4" backset, and 1/2" (3/4" at rated paired openings) throw brass or stainless steel latchbolt.

2. Locks are to be non-handed and fully field reversible.

3. Extended cycle test: Locks to have been cycle tested in ordinance with ANSl/BHMA 156.2 requirements to 2 million cycles.

4. Manufacturers:

a. Schlage (SC) - Match facility standard

b. No Substitution.

2.06 LOCK AND LATCH STRIKES

A. Strikes: Provide manufacturer's standard strike with strike box for each latch or lock bolt, with curved lip extended to protect frame, finished to match door hardware set, unless otherwise indicated, and as follows:

1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by manufacturer.

2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim.

3. Aluminum-Frame Strike Box: Provide manufacturer's special strike box fabricated for aluminum framing.

4. Double-lipped strikes: For locks at double acting doors. Furnish with retractable stop for rescue hardware applications.

B. Standards: Comply with the following:

1. Strikes for Mortise Locks and Latches: BHMA A 156.13.

2. Strikes for Bored Locks and Latches: BHMA A 156.2.

3. Strikes for Auxiliary Deadlocks: BHMA A 156.36.

4. Dustproof Strikes: BHMA A 156.16.

2.07 DOOR CLOSERS

A. All door closers specified herein shall meet or exceed the following criteria:

1. General: Door closers to be from one manufacturer, matching in design and style, with the same type door preparations and templates regardless of application or spring size.

Closers to be non-handed with full sized covers including installation and adjusting information on inside of cover.

2. Standards: Closers to comply with UL-1 OC for Positive Pressure Fire Test and be U.L.

listed for use of fire rated doors.

3. Cycle Testing: Provide closers which have surpassed 15 million cycles in a test witnessed and verified by UL.

4. Size of Units: Comply with manufacturer's written recommendations for sizing of door closers depending on size of door, exposure to weather, and anticipated frequency of use.

Where closers are indicated for doors required to be accessible to the physically handicapped, provide units complying with ANSI ICC/A117.1.

Metropolitan Library System 2018 - Village Library Renovation 087102-5 DOOR HARDWARE

5. Closer Arms: Provide heavy duty, forged steel closer arms unless otherwise indicated in Hardware Sets.

6. Closers shall not be installed on exterior or corridor side of doors; where possible install closers on door for optimum aesthetics.

7. Closer Accessories: Provide door closer accessories including custom templates, special mounting brackets, spacers and drop plates as required for proper installation. Provide through-bolt and security type fasteners as specified in the hardware sets.

8. Hurricane and Tornado Resistance Compliance: Door closers to be U.L. listed for windstorm assemblies where applicable. Provide the appropriate hurricane or tornado resistant products that have been independent third party tested, certified, and labeled to meet state and local windstorm building codes applicable to project.

B. Door Closers, Surface Mounted (Large Body Cast Iron): ANSl/BHMA A 156.4, Grade 1 surface mounted, heavy duty door closers with complete spring power adjustment, sizes 1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron body construction, with adjustable backcheck and separate non-critical valves for closing sweep and latch speed control.

1. Manufacturers:

a. LCN Closers (LC) - Match facility standard

b. No Substitution.

2.08 ARCHITECTURAL TRIM

A. Door Protective Trim

1. General: Door protective trim units to be of type and design as specified below or in the

Hardware Sets.

2. Size: Fabricate protection plates (kick, armor, or mop) not more than 2" less than door width (LDW) on stop side of single doors and 1" LDW on stop side of pairs of doors, and not more than 1" less than door width on pull side. Coordinate and provide proper width and height as required where conflicting hardware dictates. Height to be as specified in the Hardware Sets.

3. Where plates are applied to fire rated doors with the top of the plate more than 16" above the bottom of the door, provide plates complying with NFPA 80. Consult manufacturer's catalog and template book for specific requirements for size and applications.

4. Protection Plates: ANSl/BHMA A156.6 certified protection plates (kick, armor, or mop), fabricated from the following:

a. Stainless Steel: 300 grade, 050-inch thick.

b. Options and fasteners: Provide manufacturer's designated fastener type as specified in the Hardware Sets. Provide countersunk screw holes.

c. Manufacturers:

1) Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).

2.09 DOOR STOPS AND HOLDERS

A. General: Door stops and holders to be of type and design as specified below or in the Hardware Sets.

B. Door Stops and Bumpers: ANSl/BHMA A 156.16, Grade 1 certified door stops and wall bumpers. Provide wall bumpers, either convex or concave types with anchorage as indicated, unless floor or other types of door stops are specified in Hardware Sets. Do not mount floor stops where they will impede traffic. Where floor or wall bumpers are not appropriate, provide overhead type stops and holders.

1. Manufacturers:

a. Rockwood Products; ASSA ABLOY Architectural Door Accessories (RO).

2.10 ARCHITECTURAL SEALS

A. General: Thresholds, weatherstripping, and gasket seals to be of type and design as specified below or in the Hardware Sets. Provide continuous weatherstrip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated. At exterior applications provide non-corrosive fasteners and elsewhere where indicated.

Metropolitan Library System 2018 - Village Library Renovation 08 7102 - 6 DOOR HARDWARE

B. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strips are easily replaceable and readily available from stocks maintained by manufacturer.

C. Manufacturers:

1. Pemko Products; ASSA ABLOY Architectural Door Accessories (PE).

2.11 FABRICATION

A. Fasteners: Provide door hardware manufactured to comply with published templates generally prepared for machine, wood, and sheet metal screws. Provide screws according to manufacturers recognized installation standards for application intended.

2.12 FINISHES

A. Standard: Designations used in the Hardware Sets and elsewhere indicate hardware finishes complying with ANSl/BHMA A 156.18, including coordination with traditional U.S. finishes indicated by certain manufacturers for their products.

B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware

C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

D. Match existing hardware finishes at new doors in remodel area.

PART 3- EXECUTION

3.01 EXAMINATION

A. Examine scheduled openings, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance.

B. Notify architect of any discrepancies or conflicts between the door schedule, door types, drawings and scheduled hardware. Proceed only after such discrepancies or conflicts have been resolved in writing.

3.02 PREPARATION

A. Hollow Metal Doors and Frames: Comply with ANSI/DH I A 115 series.

B. Wood Doors: Comply with ANSI/DH I A 115-W series.

3.03 INSTALLATION

A. Install each item of mechanical and electromechanical hardware and access control equipment to comply with manufacturer's written instructions and according to specifications.

1. Installers are to be trained and certified by the manufacturer on the proper installation and adjustment of fire, life safety, and security products including: hanging devices; locking devices; closing devices; and seals.

B. Mounting Heights: Mount door hardware units at heights indicated in following applicable publications, unless specifically indicated or required to comply with governing regulations:

1. Standard Steel Doors and Frames: DHl's "Recommended Locations for Architectural

Hardware for Standard Steel Doors and Frames."

2. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for

Wood Flush Doors."

3. Where indicated to comply with accessibility requirements, comply with ANSI A 117 .1

"Accessibility Guidelines for Buildings and Facilities."

4. Provide blocking in drywall partitions where wall stops or other wall mounted hardware is located.

C. Retrofitting: Install door hardware to comply with manufacturer's published templates and written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work specified in Division 9

Metropolitan Library System 2018 - Village Library Renovation 08 7102 - 7 DOOR HARDWARE

Sections. Do not install surface-mounted items until finishes have been completed on substrates involved.

D. Thresholds: Set thresholds for exterior and acoustical doors in full bed of sealant complying with requirements specified in Division 7 Section "Joint Sealants."

E. Storage: Provide a secure lock up for hardware delivered to the project but not yet installed.

Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation.

3.04 FIELD QUALITY CONTROL

A. Field Inspection: Supplier will perform a final inspection of installed door hardware and state in report whether work complies with or deviates from requirements, including whether door hardware is properly installed, operating and adjusted.

3.05 ADJUSTING

A. Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.

3.06 CLEANING AND PROTECTION

A. Protect all hardware stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame.

B. Clean adjacent surfaces soiled by door hardware installation.

C. Clean operating items as necessary to restore proper finish. Provide final protection and maintain conditions that ensure door hardware is without damage or deterioration at time of owner occupancy.

3.07 DEMONSTRATION

A. Instruct Owner's maintenance personnel to adjust, operate, and maintain mechanical and electromechanical door hardware.

3.08 DOOR HARDWARE SETS

A. The hardware sets represent the design intent and direction of the owner and architect. They are a guideline only and should not be considered a detailed hardware schedule. Discrepancies, conflicting hardware and missing items should be brought to the attention of the architect with corrections made prior to the bidding process. Omitted items not included in a hardware set should be scheduled with the appropriate additional hardware required for proper application and functionality.

B. The supplier is responsible for handing and sizing all products and providing the correct option for the appropriate door type and material where more than one is presented in the hardware sets. Quantities listed are for each pair of doors, or for each single door.

C. Manufacturer's Abbreviations:

Metropolitan Library System 2018 - Village Library Renovation

1. MK - MCKINNEY

3. SC - SCHLAGE

4. HS- HES

5. RO - ROCKWOOD

6. LC - LCN CLOSERS

8. PE- PEMKO

08 7102 - 8 DOOR HARDWARE

HARDWARE SETS

SET: 1.0 DOOR #150

3 HINGE

1 CLASSROOM LOCK

1 DOOR CLOSER

1 STOP

3 SILENCER

SET: 2.0 DOOR #115

3 HINGE

1 PRIVACY SET

1 DOOR CLOSER

1 KICK PLATE

1 STOP

1 GASKETING

Metropolitan Library System 2018 - Village Library Renovation

TA2714 4-1/2" X 4-1/2" US26D MK

MATCH EXISTING FACILTIY KEYWAY, 626 SC

LEVER DESIGN AND FINISH

4040XP SERIES X ARM I BRACKETS

PER APPLICATION

FLOOR 441 CU US26D OR WALL 409

AS REQUIRED

608-RKW

TA2714 4-1/2" X 4-1/2"

MATCH EXISTING FACILITY LEVER

DESIGN AND FINISH

4040XP SERIES X ARM I BRACKETS

PER APPLICATION

K105010" X WIDTH REQ'D CSK

FLOOR 441 CU US26D OR WALL 409

AS REQUIRED

S88D

END OF SECTION

08 7102 - 9

AL LC

US32D RO

RO

US26D MK

626 SC

AL LC

US32D RO

US32D RO

PE

DOOR HARDWARE