Material Specifications

Material Specifications

All equipment/materials/parts described below are the basis for the playground equipment for this project and the contractor shall provide equipment that is equivalent or better.

Material: All materials shall be structurally sound and suitable for safe play. Durability shall be ensured on all steel parts by the use of time-tested coatings such as zinc plating, galvanizing, ProShield® finish, TenderTuff™ coating, etc. Colors shall be specified.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless-steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). All primary fasteners shall include a locking patch type material that will meet the minimum torque requirements of IFI-125. Manufacturer to provide special tools for pinned tamperproof fasteners.

TenderTuff Coating: Metal components to be TenderTuffcoated shall be thoroughly cleaned in a hot phosphatizing wash system, then primed with a water-based thermosetting solution. Primed parts shall be preheated prior to dipping in UV stabilized, liquid polyvinyl chloride (PVC), then salt cured at approximately 400 degrees. The finished coating shall be approximately .080" thick at an 85 durometer with a minimum tensile strength of 1700 psi and a minimum tear strength of 250 lbs/inch.

ProShield Finish: All metal components with ProShield finish shall be thoroughly cleaned and pretreated through a multi-stage wash system. Parts are then thoroughly dried, preheated and processed through a set of powder spray guns where a minimum .002" of epoxy primer is applied. A minimum .004" of architectural-grade Super Durable polyester TGIC powder is applied. The average ProShield film thickness is .006". ProShield is formulated and tested per the following ASTM standards. Each color must meet or exceed the ratings listed below:

• Hardness (D3363) rating 2H

• Flexibility (D522) pass 1/8" mandrel

• Impact (D2794) rating minimum 80 inch-pounds

• Salt Fog Resistance (B117 and D1654) 4,000 hours and rating 6 or greater

• UV Exposure (G154, 340 bulb) 3,000 hours, rating delta E of 2, and 90 percent gloss retention*

• Adhesion (D3359, Method B) rating 5B The Paint Line shall employ a “checkered” adhesion test daily.

Decks: All decks shall be of modular design and have 5/16" diameter holes on the standing surface.

There shall be a minimum of (4) slots in each face to accommodate face mounting of components.

Decks shall be manufactured from a single piece of low carbon 12 GA (.105") sheet steel conforming to ASTM specification A-1011. The sheet shall be perforated with a return flange on the perimeter to provide the reinforcement necessary to ensure structural integrity. There shall be no unsupported area larger than 3.5 square feet. Decks shall be designed so that all sides are flush with the outside edge of the supporting posts. Not applicable for Evos or Weevos.

Concrete Products: Two processes are used to produce concrete products. (See specific product installation/ specification documents.)

1. Glass Fiber Reinforced Concrete (GFRC) Products: Glass fiber is alkali-resistant (AR) with high tensile properties formulated for concrete. GFRC nominal product thickness is 1" with a unit weight of about 12 lbs per square foot and an average ultimate flexural strength of 2,100 psi per ASTM C947. Finish:

Exterior latex paint suited for concrete applications.

2. Precast Concrete Products: Wet-cast solid, molded concrete with an average compressive strength of 5,000 psi per ASTM C39. Unit weight range of about 115-145 lbs per cubic foot. Finish: Exterior latex paint suited for concrete applications.

Rotationally Molded Polyethylene Parts: These parts shall be molded using prime natural linear low-density polyethylene having a tensile strength of 2400 psi per ASTM D638. Rotational molding resin is compounded with color and UV-stabilizing additives with a nominal wall thickness typically 1/4" with some variation depending upon product type.

Recycled Permalene Parts: These parts shall be manufactured from 3/4" high-density polyethylene that has been specially formulated for optimum UV stability and color retention. Products shall meet or exceed density of .960 G/cc per ASTM D1505, tensile strength of 2400 PSI per ASTM D638. Available in a three-layer product with (2) .100" thick colored exterior layers over a .550" thick recycled interior core.

Footings: Unless otherwise specified, the bury on all footings shall be 34" below Finished Grade (FG) on all in-ground play events/posts. Other types of anchoring are available upon request.

Hardware Packages: All shipments shall include individual component-specific hardware packages. Each hardware package shall be labeled with the part number, description, a component diagram showing the appropriate component, package weight, a bar code linking the hardware package to the job number, assembler’s name, date and time the package was assembled, work center number and work order number.

Installation Documentation: All shipments shall include a notebook or packet of order-specific, step by-step instructions for assembly of each component, including equipment assembly diagrams, estimated hours for assembly, footing dimensions, concrete quantity for direct bury components, fall height information, area required information and detailed material specifications.

Packing List: All shipments shall include a packing list for each skid/container, specifying the part numbers and quantities on each skid or within each container.

Packaging: All components shall be individually wrapped or bulk wrapped and placed on skids (pallets) then shrink-wrapped to provide protection during shipment. Small parts and hardware packages will be placed in crates for shipment. Other components shall be individually wrapped or bulk wrapped to provide protection during shipment.

Maintenance Kit: An order-specific maintenance kit shall be provided for each structure order. The kit will include a notebook or packet with a second set of installation documents and order-specific maintenance documentation with recommendations on how often to inspect, what to look for and what to do to keep the equipment in like-new condition. The kit also includes touch-up primer, appropriate color touch-up paint, sandpaper, appropriate color touch-up PVC and additional installation tools for the tamperproof fasteners.

(PB) PlayBooster General Specifications:

Posts: Post length shall vary depending upon the intended use and shall be a minimum of 42" above the deck height. All posts shall be ProShield finished to specified color. All posts shall have a “finished grade marker” positioned on the post identifying the 34" bury line required for correct installation and the top of the loose fill protective surfacing. Top caps for posts shall be aluminum die cast from 369.1 alloy and ProShield finished to match the post color. All caps shall be factory installed and secured in place with

(3) self-sealing rivets. A molded low-density polyethylene cap, with drain holes, shall be pressed onto the bottom end of the post to increase the footing area.

Steel Posts: All steel PlayBooster posts are manufactured from 5" O.D. tubing with a wall thickness of .120" and shall be galvanized after rolling and shall have both the I.D. and the cut ends sprayed with a corrosion resistant coating.

Steel Post Mechanical Properties:

• Yield Strength (min): 50,000 PSI

• Tensile Strength (min): 55,000 PSI

• Elongation: 25% in 2 inches

• Modulus of Elasticity: 29.5 x 106 PSI Aluminum Posts: All aluminum PlayBooster posts are manufactured from 6005-T5 extruded tubing conforming to ASTM B-221. Posts shall have a 5" outside diameter with a .125" wall thickness.

Aluminum Post Mechanical Properties:

• Yield Strength (min): 35,000 PSI

• Tensile Strength (min): 38,000 PSI

• Elongation: 10% in 2 inches

• Modulus of Elasticity: 10 x 106 PSI Arch Posts: Aluminum arch posts shall be manufactured from 6005-T5 alloy. The arch shall be formed to a 21" center line radius to complement the 42" center-to-center module. The arch shall be of one continuous piece construction. There shall be no welds or additional pieces mechanically fastened to manufacture the arch. Each arch shall be designed to provide a minimum of 90 1/2" clear span from the deck to the inside of the arch at the radius peak. Arches shall be ProShield finished to a specified color.

Clamps: All clamps are ProShield finished and, unless otherwise noted, shall be die cast using a 369.1 aluminum alloy and have the following mechanical properties:

• Ultimate Tensile: 47,000 PSI

• Yield Strength: 28,000 PSI

• Elongation: 7% in 2 inches

• Shear Strength: 29,000 PSI

• Endurance Limit: 20,000 PSI Each functional clamp assembly shall have an appropriate number of half clamps and shall be fastened to mating parts with (2) 3/8" x 1 1/8" pinned button head cap screws (SST) and (2) stainless-steel (SST) recessed “T” nuts. A 1/4" aluminum drive rivet with stainless steel pin is used to ensure a secure fit to the post.

PlayBooster® clamps have three functional applications and shall be named as follows:

1. Offset hanger clamp assembly

2. Deck hanger clamp assembly

3. Hanger clamp assembly Netplex Clamps: All clamps are ProShield finished and, unless otherwise noted, shall be die cast using a

369.1 aluminum alloy and have the following mechanical properties:

• Ultimate Tensile: 47,000 PSI

• Yield Strength: 28,000 PSI

• Elongation: 7% in 2 inches

• Shear Strength: 29,000 PSI

• Endurance Limit: 20,000 PSI Each functional clamp assembly shall have an appropriate number of rope clamps and back clamps and shall be fastened to each other with (2) 5/8" x 1 1/2" pinned button head cap screws (SST) and (2) stainless-steel (SST) recessed “T” nuts. Either a face clamp shall be fastened to rope clamp with (2) 3/8" by 1-3/8" pinned button head cap screws or a single tab casting plate shall be fastened to rope clamp with (4) 3/8" by 1-3/8" pinned button head cap screws with 3/8" SAE flat washers. A 1/4" x 5/8" aluminum drive rivet with stainless steel pin is used to ensure a secure fit to the post.

Geoplex Clamps: All clamps are ProShield finished and, unless otherwise noted, shall be fabricated from 7GA using .179" (4,54 mm) T316 stainless steel.

• Ultimate Tensile: 84,000 PSI

• Yield Strength: 25,000 PSI

Each functional clamp assembly shall have an appropriate number of locking clamps and shall be fastened to mating parts with (2) 3/8" x 7/8" pinned button head cap screws (SST) with (2) 3/8" SAE flat washers. A 1/4" aluminum drive rivet with stainless steel pin is used to ensure a secure fit to the post.

Steel-reinforced cables: Made of tightly woven, polyester-wrapped, six-stranded galvanized steel cable.

These abrasion-resistant, color-stable cables are extremely durable and vandal resistant.

Design Specific Material Specifications:

156230A Bridge w/Guardrails w/Curbs

Bridge Handrail: Weldment comprised of 1.900" (48,26 mm) O.D. RS-20 (.090" - .100") (2,28 mm-2,54

mm) galvanized steel tubing beam, 1.315" (33,40 mm) O.D. RS-20 (.080" - .090") (2,03 mm-2,28 mm) and 1/4" x 1 3/4" (6,35 mm x 44,45 mm) steel half clamps. Finish: ProShield

Half Clamp: Cast aluminum. Finish: ProShield

Curb: Compression molded Permalene 3/4" (19,05 mm) thick x 5" (127 mm) high U.V. stabilized high-density polyethylene with all edges eased.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Bridge/Ramp: Weldment comprised of 12 GA (.105") (2,66 mm) sheet HRPO steel conforming to ASTM A1011 and 3/16" (4,75 mm) HR flat steel. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff.

171870A Double-Wide Ramp w/Guardrails and Curbs (ASTM) Deck to Ground

Ramp Handrail: Weldment comprised of 1.25" (31,75 mm) O.D. x 12 Ga. (.109") (2,77 mm) wall galvanized steel tubing, and 1/4" x 1 3/4" (6,35 mm x 44,45 mm) steel half clamps. Finish: ProShield.

Curb: Compression molded Permalene 3/4" (19,05 mm) thick x 5" (127 mm) high U.V. stabilized high-density polyethylene with all edges eased.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Clamps: Cast aluminum. Finish: ProShield

Bridge/Ramp: Weldment comprised of 12 GA (.105") (2,66 mm) sheet HRPO steel conforming to ASTM A1011 and 3/16" (4,75 mm) HR flat steel. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff

Ramp Infill: Fabricated from .075" (1,90 mm) HRPO steel sheet. Finish: TenderTuff

115223A Bubble Panel Above Deck

Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish:

ProShield

Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with

(2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield

Nylon Spacer: 3/8" (9,53 mm) I.D. nylon washer.

Bubble: Vacuum formed .230" x 26 1/2" (5,84 mm x 673,1 mm) diameter clear polycarbonate.

Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Permalene Panel: One-color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high

127439A Navigator Reach Panel Above Deck

Access Clamp: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate and 1/4" x 1 3/4" (6,35 mm x 44,45 mm) wide steel clamp. Finish: ProShield

Permalene Panel: Two color panel measures 34" (864 mm) wide x 13” (330 mm) high

Half Clamp: Cast aluminum. Finish: ProShield

Angle: Fabricated from formed 11 GA (.120") (3,04 mm) HRPO sheet steel. Finish: ProShield

Hub: One-color Permalene

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

Wheel: 12" (305 mm) diameter cast A319.1 aluminum alloy. Shaft-303 stainless steel. Finish: TenderTuff

Wheel Bracket: Weldment comprised of formed 3/16" (4,75 mm) plate and 5/8" (15,88 mm) O.D.

stainless steel shaft. Finish: ProShield

127953A Handhold Panel Set

Handhold Panel: Recycled Permalene

Clamps: Cast aluminum. Finish: ProShield

Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish:

ProShield

159459A Ring-A-Bell Panel Above Deck

Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with

(2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield

Bell Striker: Recycled Permalene.

Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield

Bell: Fabricated from 10 GA. (.135") (3,42 mm) HRPO low carbon steel. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish:

ProShield

Permalene Panel: Two color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high

160694A Barrier With Infill Panel

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

Infill Panel: Recycled Permalene

Clamps: Cast aluminum. Finish: ProShield

Barrier: Weldment comprised of 1.125" (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel tube per ASTM A513 with 203 or 303 stainless steel welded inserts with 5/8" (15,88 mm) internal threads and 1/4" (6,35 mm) tabs. Finish: TenderTuff

164094A Bongo Reach Panel Above Deck

Access Clamp: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate and 1/4" x 1 3/4" (6,35 mm x 44,45 mm) wide steel clamp. Finish: ProShield

Panel: Two color Permalene panel measures 34" (864 mm) wide x 18" (457 mm) high

Angle: Fabricated from formed 11 GA (.120") (3,04 mm) HRPO sheet steel. Finish: ProShield

Screen Plate: Fabricated from 12 GA. (.105") (2,66 mm) HRPO flat steel.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Clamps: Cast aluminum. Finish: ProShield

Bongo: Rotationally molded from U.V. stabilized linear low-density polyethylene

173565A Xylofun Panel Above Deck

Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with

(2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Clamps: Cast aluminum. Finish: ProShield

Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish:

ProShield

Xylofun Panel Assy.: (Panels) Two color Permalene, color specified. 1/8" (3,17 mm) Thick steel, .125" (3,17 mm) O.D. aluminum tube and 1/2" (12,7 mm) threaded steel rod. Finish: ProShield

120818A Playstructure Seat

Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield

Seat: Flange formed from 11 GA (.120") (3,04 mm) sheet steel. Seating surface is perforated with 1/4" (6,35 mm) diameter holes. Finish: TenderTuff

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

138871A Sway Fun Wheelchair Glider 16"Height

Pipebolt: Fabricated from 1.125" (28,58 mm) O.D. 6061-T6 aluminum tube, with 3/8" (9,53 mm) internal threads.

Axle: Weldment comprised of 304 stainless steel.

Arm Assembly: Machined from 6061-T6 aluminum.

Bench: Rotationally molded from U.V. stabilized linear low-density polyethylene

Base Frame: Weldment comprised of 3" x 5" (76 mm x (127 mm) structural steel C channel, 1/4" (6,35

mm) HRS flat steel, 1/2" (12,7 mm) HRS flat steel and 1/2" (12,7 mm) HRPO flat steel. Finish: Hot dip galvanized per ASTM A123 category 100.

Deck: Flange formed from 11 GA (.120") (3,04 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff

Deck Extension: Flanged formed from 11 GA (.120") (3,04 mm) sheet steel conforming to ASTM A1011.

Finish: TenderTuff

Deck Extension Support: Formed from 11 GA (.120") (3,04 mm) sheet steel conforming to ASTM A1011.

Finish: ProShield

Deck Mount Frame: Weldment comprised of 11 GA (.120") (3,04 mm) sheet steel, 7 GA. (.180") (4,57

mm) HRPO flat steel and 1/4" (.250") (6,35 mm) HRPO flat steel. Finish: Hot dip galvanized per ASTM A123 category 100.

Lower Side Panel: One-color Permalene

Panel Guard: Permalene

Side Panel Frame: Weldment comprised of 11 GA (.120") (3,04 mm) sheet steel conforming to ASTM A1011. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Table Panel: Permalene table measures 50 3/8" (1279,53 mm) wide x 22 15/16" (582,60 mm) deep

Table Post: Weldment comprised of 3.500" (88,9 mm) O.D. RS-20 (.125") (3,17 mm) galvanized steel tubing, 11 GA (.120") (3,04 mm) HRPO ASTM A1011 sheet steel and 1/4" (6,35 mm) HRS flat steel.

Finish: ProShield

Upper Shock Mount Bracket: Weldment comprised of 7 GA (.180") (4,57 mm) sheet steel conforming to ASTM A1011. Finish: Hot dip galvanized per ASTM A123 category 100.

Upper Side Panels: Permalene

Spacer: One-color Permalene

111467B 2"Straight Ring Bridge

Chain Assembly: 5/16" (7,92 mm) Low carbon steel straight link galvanized chain, with bolt link made from grade 316 stainless steel. Finish: TenderTuff-coated

Half Clamp: Cast aluminum. Finish: ProShield

Double Clevis: Stainless Steel

D Ring: Cast from A356 aluminum alloy with a cast in place 841 bronze alloy bushing. Finish: TenderTuff

Beam: Weldment comprised of 2.375" (60,33 mm) O.D. RS-40 (.130" - .140") (3,30 mm-3,56 mm) galvanized steel tubing, and 1/4" (6,35 mm) HRPO flat steel. Housing for double clevis are 1 1/4" (31,75

mm) O.D. x .312" (7,92 mm) wall steel tubing. SAE 841 dry bronze bushings are pressed into housing at factory. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

193170A LolliLadder w/2 E-Pods

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

E-Pod: Rotationally molded from U.V. stabilized linear low-density polyethylene

Pod Casting: Fabricated from sand cast alloy 356 in accordance with ASTM B26. Finish: ProShield

Rung Cap: EPDM

LolliLadder: Weldment comprised of 1/4" (6,35 mm) HRPO flat steel, 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm-3,55 mm) wall galvanized steel tubing, and 1.315" (33,40 mm) O.D. RS20 (.080"- .090") (2,03 mm-2,29 mm) wall galvanized tubing. Finish: ProShield®

Clamps: Cast aluminum. Finish: ProShield

111404J 76"Alum Post DB Post: See PlayBooster (PB) General Specifications.

111404I 84"Alum Post DB Post: See PlayBooster (PB) General Specifications.

111404H 92"Alum Post DB Post: See PlayBooster (PB) General Specifications.

111404E 116"Alum Post DB Post: See PlayBooster (PB) General Specifications.

111404C 132"Alum Post DB Post: See PlayBooster (PB) General Specifications.

111405I

42"Alum Flush Post w/D Shaped Cap DB Post: See PlayBooster (PB) General Specifications.

Flush Mount Cap: Weldment comprised of 4.675" (118,75 mm) O.D. x 4" (102 mm) long aluminum sleeve and 3/16" (4,75 mm) thick x 4.875" (123,83 mm) top cap. Finish: Tendertuff

111405H 50"Alum Flush Post w/Turtle Cap DB Post: See PlayBooster (PB) General Specifications.

Flush Mount Cap: Weldment comprised of 4.675" (118,75 mm) O.D. x 4" (102 mm) long aluminum sleeve and 3/16" (4,75 mm) thick x 4.875" (123,83 mm) top cap. Finish: Tendertuff

154884A CoolToppers Single Post Pyramid Roof DB Only

Clamp: Weldment comprised of 1/4" x 3" (6,35 mm x 76 mm) HRPO flat steel and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield

Extension Arms: Weldment comprised of 2.375" (60,33 mm) O.D. RS-20 (.095"-.105") (2,41 mm-2,66

mm) galvanized steel tubing, 1/4" (6,35 mm) steel plate and 1/4" (6,35 mm) diameter carbon steel J-hooks. Finish: ProShield

CoolTopper Shade Top: Heavy duty, 62.9 mils (1.6 mm) thick professional grade shade fabric for tensioned structures and other shade applications. Made from UV stabilized HDPE monofilament and tape yarns. Specialized lock stitch knit for more air movement and better channeling of cooling breezeways. Constructed to block up to 97.7% of harmful UV sun rays. Fade and tear resistant, will not crack, rot or fray. Tensile strength warp 142.75 lbs. weft 560.67 lbs. Tear strength warp 42.03 lb. and weft 80.70 lbs. Burst pressure 507.63 PSI. Remove fabric when wind speed is expected to exceed 90 mph and snow load is expected to exceed 5 psf, per International Building Code (IBC) 2009.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

182503C Welcome Sign (LSI Provided) Ages 5-12 years Direct Bury

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

Sign Panel: Panel is fabricated from 1/8" (.125”) (3,17 mm) aluminum plate. Finish: ProShield®. (Sign) Digital image is transferred to a 1/8" (.125”) (3,17 mm) ProShield coated aluminum plate, then infused into the ProShield.

Post: Weldment comprised 2.375" (60,33 mm) O.D. RS20 (.095-.105) (2,41 mm-2,67 mm) wall galvanized tube, 1/4" (6,35 mm) HRPO steel sheet and aluminum post cap. Finish: ProShield

156232A Ramp w/Guardrails w/Curbs Meets ASTM

Ramp Handrail: Weldment comprised of 1.25" (31,75 mm) O.D. x 12 Ga. (.109") (2,77 mm) wall galvanized steel tubing, and 1/4" x 1 3/4" (6,35 mm x 44,45 mm) steel half clamps. Finish: ProShield

Curb: Compression molded Permalene 3/4" (19,05 mm) thick x 5" (127 mm) high U.V. stabilized high-density polyethylene with all edges eased

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Clamps: Cast aluminum. Finish: ProShield

Bridge/Ramp: Weldment comprised of 12 GA (.105") (2,66 mm) sheet HRPO steel conforming to ASTM A1011 and 3/16" (4,75 mm) HR flat steel. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff

158997A Pod Climber 10" DB

Support: Weldment comprised of 1.900" (48,26 mm) O.D. RS-20 (.090" - .100") (2,28 mm-2,54 mm) 1.315" (33,40 mm) O.D. RS-20 (.080" - 090") (2,03 mm-2,28 mm) and 3/16" x 5" (4,75 mm x 127 mm) diameter plate. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Disc: Rotationally molded from U.V. stabilized linear low-density polyethylene, disc measures 14" (356

mm) in diameter x 7" (178 mm) high

154752A

Hex Deck w/One Extension

Hex Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011.

Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 36 3/4" (66,68 mm x 933,45 mm) per each of the six sides for an overall dimension of 77 5/8" (1971,68 mm) face to face. Finish: TenderTuff

Hex Deck Extension: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 42" x 78" (66,68 mm x 1067 mm x 1981 mm). Finish: TenderTuff

Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield

Deck Brace: Fabricated from 3/8" x 1 3/4" x 28 1/2" long zinc plated steel strap. Finish: ProShield®

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

178710A Hexagon Tenderdeck

Hex Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011.

Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 36 3/4" (66,68 mm x 933,45 mm) per each of the six sides for an overall dimension of 77 5/8" (1971,68 mm) face to face. Finish: TenderTuff

Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield

Deck Brace: Fabricated from 3/8" x 1 3/4" x 28 1/2" long zinc plated steel strap. Finish: ProShield®

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

191031A Accessible Panel Curb

Curb Panel: Permalene

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

195507A ZipKrooz Additional Bay 34' w/Aluminum Posts DB

Chain w/Rubber Cover Assy.: (Chain) Steel 1/4" (6,35 mm) straight link chain, 3,150 lbs. (1428,82 kilograms) working load limit. Finish: ProGuard. (Cover) High pressure Buna-N Rubber hose. (Connector) Aluminum.

Post: See PlayBooster (PB) General Specifications.

Spacer: .190"(4,82 mm) Thick aluminum sheet.

Track: Extruded from 6005-T4 aluminum alloy. Finish: ProShield®

Trolley Assy.: Steel body with urethane rollers. Completely assembled. Steel Body Finish: ProShield®, Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011, 1/4" (6,35

mm) HRPO flat steel and 3/8" (9,53 mm) HRPO flat steel. Standing surface is perforated with 5/16" (7,94

mm) diameter holes. The finished size measures 2 1/8" x 38 1/2" x 38 1/2" (53,98 mm x 977 mm x 977 mm). Finish: TenderTuff.

Deck Support: Weldment comprised of 5" (127 mm) O.D. x 7 GA. (.179") (4,54 mm) wall galvanized steel tube, and 1/2" (12,7 mm) HRPO steel plate. Finish: ProShield®

Crossover: Weldment comprised of tee clamps and a 5" (127 mm) O.D. extruded 6005-T5 aluminum alloy tube with a .125" (3,17 mm) wall. Finish: ProShield

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

E-Pod: Rotationally molded from U.V. stabilized linear low-density polyethylene

Clamps: Cast aluminum. Finish: ProShield

Bumper: Urethane

ZipKrooz Crossover: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm-3,55

mm) wall galvanized steel tubing, 3/8" (9,52 mm) thick HRPO steel plate and 1/4" (6,35 mm) thick HRPO steel. Finish: ProShield®

196212A ZipKrooz Assisted 34' w/Aluminum Posts DB

Post: See PlayBooster (PB) General Specifications.

Spacer: .190"(4,82 mm) Thick aluminum sheet.

Track: Extruded from 6005-T4 aluminum alloy. Finish: ProShield®

Trolley Assy.: Steel body with urethane rollers. Completely assembled. Steel Body Finish: ProShield®

Cable Assy.: (Cable) Made of tightly woven polyester-wrapped, six-stranded galvanized-steel cable with a polypropylene core. (Cable Connectors) 6063-T6 aluminum.

Crossover: Weldment comprised of tee clamps and a 5" (127 mm) O.D. extruded 6005-T5 aluminum alloy tube with a .125" (3,17 mm) wall. Finish: ProShield

Bucket Seat Mount: Weldment comprised of 1.42" (36,06 mm) diameter stainless steel, 1.660" (42,16

mm) O.D. RS20 (.085"-.095") (2,16 mm-2,41 mm) wall galvanized steel tubing, 3/8" (9,53 mm) thick HRPO steel plate and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield®

Bucket Seat Assy: (Bucket Seat & Yoke) Rotationally molded from U.V. stabilized linear low-density polyethylene. (Pipebolt) Made from 1.125" (28,58 mm) O.D. 6005-T5 threaded anodized aluminum tube. (Bearings) UHMW PE lubricated. (Brackets) Made from 356-T6 aluminum.

Clamps: Cast aluminum. Finish: ProShield

Bumper: Urethane

ZipKrooz Crossover: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm-3,55

mm) wall galvanized steel tubing, 3/8" (9,52 mm) thick HRPO steel plate and 1/4" (6,35 mm) thick HRPO steel. Finish: ProShield®

Bumper: Molded from U.V. stabilized EPDM rubber encapsulating 11 GA (.120") (3,04 mm) HRPO steel sheet.

248819A We-Go-Round w/Perf Panels - 2 seats DB Only

Center Post: 6.000” (152 mm) O.D. (.250”) (6,35 mm) wall HR D.O.M. Steel Tube. Finish: ProShield®

Shock: 70 Series.

Rib: Weldment comprised of 1.5” (38,1 mm) x 3.0” (76,2 mm) x .180” (4,57 mm) wall HRPO steel tube, 3/8” (9,52 mm) thick stainless-steel tab, 3/8” (9,52 mm) O.D. stainless steel pin, 3/8” (9,52 mm) thick HRPO steel plate and 1/4” (6,35 mm) thick HRPO steel plate. Finish: ProShield®

GripX Tread: 3/4" (19,05 mm) Thick Permalene®

Brake Cover: Recycled Permalene

Bottom Mount: Weldment comprised of 7.000” (177 mm) O.D. x .188” (4,77 mm) wall stainless steel tube and 1/4” (6,35 mm) thick HRPO steel plate. Finish: ProShield

Base Bushing: Oil-Filled UHMW PE.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications).

Bottom Rib: 7GA. (.179") (4,54 mm) thick HRPO steel sheet. Finish: ProShield

Drainpipe: Comprised of 4" x 25' polypropylene perforated pipe.

Weldment comprised of 2.375" (60,32 mm) O.D. RS20 (.095" - .105") (2,41 mm-2,66 mm) wall galvanized steel tubing, 1/4" (6,35 mm) thick HRPO steel plate and 3/8" (9,52 mm) stainless steel tab.

Finish: ProShield

Mounting Hub Assembly: Comprised of 1/2" (12,7 mm) thick stainless-steel plate, 11 GA (.120") (3,05

mm) stainless steel sheet, steel bearing shaft.

Seat Frame: Comprised of 7GA (.179") (4,54 mm) thick HRPO steel plate. Finish: ProShield

Seat Permalene Panel: 3/4" thick Recycled Permalene®

Spinner Top: Rotationally molded from U.V. stabilized linear low-density polyethylene

277778A We-Go-Swing w/1 Accessible Bay DB Only

GripX Deck Surface: 3/4" (19,05 mm) Thick Permalene®

Permalene Panels: Recycled Permalene

Swing Frame: Weldment comprised of 5" (127 mm) O.D. .179 wall (4,55 mm) (7ga) Zinc Galvanized steel tubing, 3/8" (9,53 mm) HRPO steel plate, 1/2" (12,7 mm) HRPO Steel plate, bearing blocks stainless steel and self-aligning bearings. Finish; ProShield

Swing Legs: Weldment comprised of 5" (127 mm) O.D. .120 wall (3,05 mm) (11GA) zinc galvanized steel tubing, 1/2" (12,7 mm) HRPO steel plate. Finish; Proshield

Swing Arms: Weldment comprised of 2.875" (73,03 mm) O.D. RS40 (.160" - .170") (4,06 mm - 4,32 mm) wall galvanized steel tubing, 2.375" (60.33 mm) O.D. RS40 (.130" - .140") (3,30 mm - 3,56 mm) wall galvanized steel tubing, 1.90'' (48.26 mm) O.D. RS20 (.090" - .100") (2,29 mm - 25,4 mm) wall galvanized steel tubing, 1.66" (42,16 mm) O.D. RS40 (.111" - .121") (2,82 mm - 3,07 mm) wall galvanized steel tubing, 1/2" (12.7 mm) HRPO steel plate, .179" (4,55 mm) HRPO steel sheet, 2.75" (69.85 mm) O.D.

stainless steel bar, 1.25" (31,75 mm) O.D. stainless steel bar, 2.875" (73,03 mm) O.D. stainless steel bar, 1/4" (6,35 mm) stain steel plate. Finish: Proshield

Trolley Base: Comprised of 1/4" (6,35 mm) HRPO steel plate, Finish: ProShield.

Trolley Assembly: Comprised of 1-1/2" (38,1 mm) square steel bar, 3/16" (4,78 mm) stainless steel sheet, 5/16"(7,94 mm) stainless steel shafts, urethane roller skate wheels. Finish: ProShield

Trolley Spacer: 1-1/8" (28,58 mm) O.D. aluminum tubing. Finish: Proshield

Trolley Frame: Weldment comprised of .190" (4,83 mm) aluminum sheet, 1-1/8" (28,58 mm) aluminum tubing. Finish: ProShield

Seat Frame: Weldment comprised of 1.90" (48,26 mm) O.D. RS40 (.120" - .130") (3,05 mm - 3,30 mm) wall galvanized steel tubing, 1/4" (6,35 mm) HRPO steel plate. Finish: Proshield

Curb Frame: Weldment comprised of 1.029"(26,14 mm) O.D. RS20 (.070" - .090") (1,78 mm - 2,29 mm) wall galvanized steel tubing, 1/4" (6,35 mm) HRPO steel plate, .179" (4,55mm) HRPO steel sheet. Finish;

ProShield

Anchor Cage: Weldment comprised of 1/4" (6,35 mm) HRPO steel plate, 1.029" (26,14 mm) O.D. .083" (2,11 mm) wall galvanized steel tubing, 5/8-11UNC thread weld slug. Finish: ProShield.

Soft Stop: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate, .179" (4,55 mm) HRPO steel sheet.

Finish: ProShield.

Hard Stop: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate, 1/4" (6,35 mm) HRPO steel Plate.

Finish: ProShield.

Swing Arm Brace: Weldment comprised of 2.375" (60,33 mm) O.D. RS20 (.095" - .105") (2,41 mm - 2,67

mm) galvanized steel tubing, 1/4" (6,35 mm) HRPO steel plate, .179" (4,55 mm) steel sheet. Finish:

Proshield.

Belt Plates: Comprised of 1/8" (3,18 mm) aluminum sheet. Finish: ProShield.

Mending Plates: Comprised of 7 ga. (4,55 mm) HRPO steel sheet. Finish: ProShield.

Rung Cap: EPDM

Access Deck Supports: Weldment comprised of 2-1/2" (63,5 mm) x 1-1/2" (38,1 mm) x 1/4" (6,35 mm) wall rect steel tubing, 2-3/8" ((60,33 mm) RS20 (.095" - .105") (2,41 mm - 2,67 mm) wall galvanized steel tubing, 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield.

Rubber Plug: Made from .315" think mini rough top 3-ply rubber belting with polyester fabric ply’s.

Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)

Bridge/Ramp: Weldment comprised of 12 GA (.105") (2,66 mm) sheet HRPO steel conforming to ASTM A1011 and 3/16" (4,75 mm) HR flat steel. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff.