Table of Contents

COVER PAGE 1

TABLE OF CONTENTS

BLOWERS & ACCESSORIES 7

Assembly Drawing 8 Unit Outline Drawing 10 Blower Performance Data 11 Motor

Data Sheet 16 Performance Data & Curves 17 Dimensional Drawing 22 Motor Wiring Diagram 23

Paint Finish General Data Sheet 24 Base Coat PDS 25 Top Coat PDS 27

Isolation Base Pads 29 Drive Coupling 30 Coupling Guard 31 RTV Sealant 32 Material Safety Data Sheet, RTV 33 Material Safety Data Sheet, Lubricant 52

SPECIFICATIONS 64

Dynamic Rotor Balance Specifications 65 Mechanical Test Specifications 69 Gas Leak Test Specifications 78

CERTIFICATES & REPORTS 81

Dynamic Rotor Balance Test Report 82 Mechanical Run Test Report 83 Gas Leak Test Report 84

INSTALLATION & OPERATING INSTRUCTIONS 85

Blower Operation & Service Manual 86

1 About this document 90

1.1 Target groups 90

1.2 Other applicable documents 90

1.3 Area of validity 91

1.4 Warnings and symbols 91

1.5 Technical terms 92

2 Safety 93

2.1 Intended use 93

2.2 General safety instructions 93

2.2.1 Product safety 93

2.2.2 Operator’s obligations 93

2.2.3 Obligations of personnel 94

2.3 Specific hazards 94

2.3.1 Explosion-hazard area 94

2.3.2 Hazardous charged fluids 94

3 Layout and function 95

3.1 Name plates 95

3.1.1 Standard Name plate 95

3.1.2 ATEX & CE Name plate 95

3.2 Layout 96

3.3 Shaft bearing 96

3.4 Function 96

3.4.1 Pressure surges 97

3.5 Further equipment (if provided) 97

4 Transport, storage, and disposal 98

4.1 Transport 98

4.1.1 Unpacking and inspection on delivery 98

4.1.2 Lifting 98

4.2 Preservation 99

4.3 Storage 100

4.3.1 Short term storage (within 90 days) 100

4.3.2 Long-term storage 100

4.4 Removing the preservative 100

4.5 Disposal 100

5 Setup and connection 101

5.1 Preparing the setup 101

5.1.1 Checking machine condition 101

5.1.2 Checking the ambient conditions 101

5.1.3 Sliding foot arrangement (if present) 101

5.1.4 Preparing the installation site 101

5.1.5 Preparing the foundation and surface 102

5.1.6 Balancing the impellers and rotor assembly

5.2 Installing the machine 102

5.2.1 Setting the machine on the foundation 102

5.2.2 Aligning the machine 103

5.3 Installing the motor 103

5.4 Planning the pipe lines 103

5.4.1 Specifying supports and flange connections

5.4.2 Specifying nominal diameters 104

5.4.3 Providing accessories 104

5.4.4 Providing safety and control devices (recommended)

5.5 Connecting the pipe lines 105

5.5.1 Keeping the pipe lines clean 105

5.5.2 Installing the inlet pipe 105

5.5.3 Installing the outlet pipe 105

5.5.4 Installing the condensate discharge pipe (if present)

5.5.5 Shaft seals 106

5.5.6 Checking the stress-free pipe connection 106

5.5.7 Checking the pipes for leaks 106

5.6 Electrical connection 106

5.6.1 Electrical connection 106

5.6.2 Variable Frequency Drive (VFD) 107

5.6.3 Connecting the motor 107

5.7 Aligning motor and machine 107

5.7.1 Aligning the coupling 107

5.7.2 Aligning the motor 108

5.7.3 Preparing the alignment of the coupling at operating temperature

5.8 Installing safety guards 111

5.9 Checking the installation 111

6 Operation 112

6.1 Preparing for the initial start-up 112

6.1.1 Removing the preservative 112

6.1.2 Lubricating the bearings 112

6.1.3 Preparing the coupling 112

6.1.4 Checking the direction of rotation 112

6.1.5 Preheating the machine 112

6.2 Initial start-up 112

6.2.1 Switching on 112

6.2.2 Precisely aligning the coupling 113

6.3 Start-up 113

6.3.1 Switching on 113

6.3.2 Checking operation 114

6.3.3 Switching off 114

6.4 Shutting down 115

6.5 Start-up following a shutdown period 115

7 Maintenance 116

7.1 Testing the control systems 116

7.1.1 Surge control (if present) 116

7.1.2 Ammeter 116

7.1.3 Overload protection 116

7.1.4 Monitoring the temperature of the bearings 116

7.1.5 Vibration sensors 116

7.2 Monitoring 116

7.2.1 Inspection 117

7.2.2 Reinspection 117

7.2.3 Packing Gland for Gas Tight Construction 117

7.2.4 Belt drive 118

7.2.5 Antifriction bearings lubricated with grease 118

7.2.6 Bearings with oil lubrication 118

7.2.7 Cleaning the external surfaces of the machine

7.3 Disassembly 119

7.3.1 Returning the blower to the manufacturer 120

7.3.2 Preparing for disassembly 120

7.4 Installing 120

7.5 Ordering spare parts 121

8 Troubleshooting 122 9 Appendix 125

9.1 Drawings 125

9.1.1 Available flange variants 125

9.2 Technical specifications 125

9.2.1 Operating conditions 125

9.2.2 Tightening torques 126

Machine 126 Pipe threads 127 Fasteners 127

9.2.3 NPT Tightening Torques 127

9.2.4 Weight specifications 127

9.2.5 Grease types 127

9.2.6 Lubricating oils 128

9.2.7 Sound levels 128

9.2.8 Flange loads according to ISO 5199 129

9.3 Safety certificate 131

Motor Instruction Manual 133 Coupling Installation & Maintenance Instructions 188 Coupling Guard Installation & Maintenance Instructions 190

MANUFACTURER'S SERVICES 193

Customer Focused Aftermarket Solutions 194 Field Service Rate Schedule 202 AEON Lubricant Re-Order Data 205 Start-Up Checklist 206 Warranty Renewal Program 210

BLOWERS

ACCESSORIES

BEARING HOUSING VIEWED FROM INLET END

BEARING HOUSING VIEWED FROM OUTLET END

OUTLET BEARING HOUSING DETAIL

INLET BEARING HOUSING DETAIL

PARTS LIST

DESCRIPTIONQTYITEM

IMP,1003,BC,12V,810/850,319,PHENOLIC31

HEAD,INLET,810/850,POS.1,PHENOLIC12

HEAD,OUTLET,810/850,P.2,DR,PHENOLIC13

SECTION,INT,810/850,X-DRN,PHENOLIC24

SHAFT, 810/850, 3 ST,32.72",STN.STL15

LOCKWASHER,WS-16,STAINLESS STEEL16

LOCKNUT,NS-16,STAINLESS STEEL17

KEY,3/8SQ X 11.00LG.,STN.STL18

SHIM,IMPELLER,810/850,22GA.STN.STL.69

SHIM,IMPELLER,810/850,28GA,STN.STL.210

LOCKWASHER,WS-12,STAINLESS STEEL211

LOCKNUT,NS-12,STAINLESS STEEL212

KEY,1/2"SQ X 2.75 LG113

HOUSING,PACKING,600-1250,LONG LIP114

GASKET,BRG HSG,MLN562,600,810/50,1210/50215

SCREW,HH CAP,3/8-16X1.00 LG ZN GR51016

WASHER,LOCK,MED3/8 ZN1017

PACKING,600-1260318

GLAND,PACKING,600 THRU 1250119

STUD,3/8-16X2 1/2,LC PER DWG220

NUT,LOCK,HEX,3/8-16 ZN221

PLUG,PIPE,1/8",SQ.HD,STN STEEL422

LABYRINTH,MACHINED,600,810,850223

SCREW,HH CAP,5/16-18X1.25 LG ZN GR51024

WASHER,SPR,WAVY,.350"ID,.492"OD*2025

HSG BRG 600-1250 ASSY GAS LIP SEAL226

SEAL-OIL 2.88"ID x 3.756"OD x .38"WIDE227

SCREW, SET 3/8-24X3/4",STEEL,CONE POINT428

PLUG, 3/4-10 STANDARD RTD CONN.(S.S.)229

WASHER,COPPER CRUSH,3/4-10 RTD SEALING230

GASKET HEAD 600-1250 SERIES231

STUD 1/2-13UNC x 2.00"LG - MILLED END1032

NUT, HEX,1/2 - 13 ZN1033

WASHER,LOCK,MED1/2 ZN1034

PLUG,PIPE,SOCKET,1/8"NPT,STN.STL.235

CAP,BRG,600-1250,CLOSED END,SHORT LIP136

RING,BAFFLE,850,SS337

SCREW,PAN HD,PHIL,12-24X.50 STN.STL1538

TIE ROD,3/4"-10 THRD,12-3/4"LG,STL.139

TIE ROD,3/4"-10 THRD,13-1/2"LG,STL.740

NUT,HEX,3/4-10 ZN1541

WASHER,LOCK,MED3/4 ZN1542

BEARING,RADIAL BALL,6312 C3,ABEC-1243

SLINGER,600-1250 SERIES244

SHIM BEARING 600-1250 SERIES245

WASHER WAVY SPRING146

DRAIN-ASSEMBLY,853, 1/2" TUBING147

NAMEPLATE,AEON CF,CAUTION,SS148

NAMEPLATE,GD-ENG. PROD. DIV.,SERIAL149

TACK,FAST.,#4139,1/4"HD,0.030-0.040"GRIP450

DECAL,FACTORY SVC,AUTH PARTS,3X6151

A A

B B

C C

D D change is subject to price and shipping equipment on which mfg. has started. Any

Certified For Construction: This print covers established upon return of final approved however, no mfg. has started. Delivery is equipment on which mat'l has been ordered, For Final Approval: This print covers is established upon return of approved

For Approval: Tentative shipping promise promise adjustment.

print.

print.

NTS

PURCHASER:

TITLE:

REV.

SSH

APPVD. BY:DRAWN BY:

DWG. NO.:

SCALE:

THIS DRAWING IS THE PROPERTY OF

INFORMATION HEREIN MUST BE OBTAINED

PERMISSION TO USE OR DISCLOSE ANY

PROPRIETARY INFORMATION. WRITTEN

CONTAINS GARDNER DENVER NASH

CHARLEROI, PA. 15022, USA, AND

FROM GARDNER DENVER NASH LLC.

THE GARDNER DENVER NASH LLC,

DO NOT USE THIS PRINT FOR

CONSTRUCTION UNLESS

CERTIFIED AND DATED.

SHEET

SIZE:

D

DATE:

KERR PUMP & SUPPLY

BLUE SKIES ENERGY, LLC.

USER:

P.O.#:

NETWORK#:

SALES#:

P192004

5939175

5920915

06/2025

SHEET

0.06

- TOLERANCES -

3.2

- UNLESS OTHERWISE NOTED -

INFORMATION WITHOUT WRITTEN PERMISSION FROM GARDNER DENVER NASH LLC.

USE OF ANY GARDNER DENVER NASH PRODUCT. NO OTHER USE MAY BE MADE OF THIS

REPRODUCE THE INFORMATION CONTAINED HEREIN IN CONNECTION WITH THE CUSTOMER'S

0.13

MOUNTING HOLES

INCHES

1.6

PERMISSION IS HEREBY GIVEN TO ANY GARDNER DENVER NASH CUSTOMER TO USE AND

THIS DRAWING CONTAINS PROPRIETARY INFORMATION OF GARDNER DENVER NASH LLC.

DIMENSIONAL UNITS ARE:

0.25 0.50

12.7

2-IN NPS2-IN NPS

PIPE CONNECTION LOCATIONS

6.4

GENERAL

0.13

3.2

MOUNTING HOLES

4 STAGES 4 STAGES

504RSF810

A

ASSEMBLY 853-GDGI 1-2 PLABY

RWG

X

ASL/GNP

A

RELEASED, C/M 1187126 6/24/25

REVISION

REV DESCRIPTION DATE APPVD

18.00

[457]

15.38

[391]

15.38

[391]

BLOWER DATA

MODEL NO.: 853-GDGI

LUBRICATION: GREASE

INLET POSITION:

OUTLET POSITION:

DRIVE SHAFT POSITION:

INLET

4. ROTATION WHEN FACING SHAFT

3. SHAFT, DIA. WITH KEY

2. FLANGE DIMENSIONS CONFORM TO 125

POUND ANSI CAST IRON FLANGED FITTINGS

1. DIMENSIONS SHOWN IN INCHES AND [mm]

BLOWER DATA

1 7/8" 1/2"

CW

5. BLOWER WEIGHT: 1,340 lb

18.75

[476]

11.88

[302]

19.81

[503]

1 1 1

4 4

9 10

11 12

16 17

192021

23 24 25

35 35

37 38

39 40 41 42

232425

FOOT DIMENSIONS

INLET HEAD POSITION - 1

OUTLET HEAD POSITION - 2

A A

B B

C C

D D change is subject to price and shipping equipment on which mfg. has started. Any

Certified For Construction: This print covers established upon return of final approved however, no mfg. has started. Delivery is equipment on which mat'l has been ordered, For Final Approval: This print covers is established upon return of approved

For Approval: Tentative shipping promise promise adjustment.

print.

print.

NTS

PURCHASER:

TITLE:

REV.

SSH

APPVD. BY:DRAWN BY:

DWG. NO.:

SCALE:

THIS DRAWING IS THE PROPERTY OF

INFORMATION HEREIN MUST BE OBTAINED

PERMISSION TO USE OR DISCLOSE ANY

PROPRIETARY INFORMATION. WRITTEN

CONTAINS GARDNER DENVER NASH

CHARLEROI, PA. 15022, USA, AND

FROM GARDNER DENVER NASH LLC.

THE GARDNER DENVER NASH LLC,

DO NOT USE THIS PRINT FOR

CONSTRUCTION UNLESS

CERTIFIED AND DATED.

SHEET

SIZE:

D

DATE:

KERR PUMP & SUPPLY

BLUE SKIES ENERGY, LLC.

USER:

P.O.#:

NETWORK#:

SALES#:

P192004

5939175

5920915

06/2025

SHEET

0.06

- TOLERANCES -

REPRODUCE THE INFORMATION CONTAINED HEREIN IN CONNECTION WITH THE CUSTOMER'S

0.13

MOUNTING HOLES

INCHES

1.6

PERMISSION IS HEREBY GIVEN TO ANY GARDNER DENVER NASH CUSTOMER TO USE AND

THIS DRAWING CONTAINS PROPRIETARY INFORMATION OF GARDNER DENVER NASH LLC.

DIMENSIONAL UNITS ARE:

0.25 0.50

12.7

2-IN NPS2-IN NPS

PIPE CONNECTION LOCATIONS

6.4

GENERAL

0.13

3.2

MOUNTING HOLES

4 STAGES 4 STAGES

504RSF810

A

ASSEMBLY 853-GDGI 1-2 PLABY

RWG

24.00

[610]

12.00

[305]

18.00

[457]

24.00

[610]

12.00

[305]

18.00

[457]

18.75

[476]

534 N-M

60 LB 267 N-M 180 LB 120 LB

400 FT-LB 542 N-M

200 FT-LB

542 N-M

271 N-M 200 FT-LB 271 N-M

801 N-M

F1

PARALLEL TO

SHAFT

F2

VERTICAL TO

SHAFT

F3

HORIZONTAL

90°TO SHAFT

534 N-M

M1

PARALLEL TO

SHAFT

M2

VERTICAL TO

SHAFT

M3

HORIZONTAL

90°TO SHAFT

60 LB 267 N-M

180 LB

120 LB

400 FT-LB

RECOMMENDED MAXIMUM ALLOWABLE FLANGE FORCES AND MOMENTS

INLET

801 N-M

200 FT-LB 271 N-M 200 FT-LB 271 N-M

F1

PARALLEL TO

SHAFT

F2

VERTICAL TO

SHAFT

F3

HORIZONTAL

90°TO SHAFT

M1

PARALLEL TO

SHAFT

M2

VERTICAL TO

SHAFT

M3

HORIZONTAL

90°TO SHAFT

OUTLET

F2

F3

M2

M1

M3

F1

A SEE SHEET 1 FOR REVISIONS 6/24/25

REVISIONS

REV. DESCRIPTION DATE APPVD

X

ASL/GNP

18.75

[476]

13.75

[349]

11.88

[302]

19.81

[503]

15.38

[391]

15.38

[391]

12.00

[305]

12.00

[305]

2.88

[73]

6.19

[157]

2.00

[51]

5.25

[133]

(4) n0.88 THRU q INLET q OUTLET q

UNIT

INLET/OUTLET FLANGE DETAIL

A A

B B

C C

D D change is subject to price and shipping equipment on which mfg. has started. Any

Certified For Construction: This print covers established upon return of final approved however, no mfg. has started. Delivery is equipment on which mat'l has been ordered, For Final Approval: This print covers is established upon return of approved

For Approval: Tentative shipping promise promise adjustment.

print.

print.

NTS

PURCHASER:

TITLE:

REV.

SSH

APPVD. BY:DRAWN BY:

DWG. NO.:

SCALE:

THIS DRAWING IS THE PROPERTY OF

INFORMATION HEREIN MUST BE OBTAINED

PERMISSION TO USE OR DISCLOSE ANY

PROPRIETARY INFORMATION. WRITTEN

CONTAINS GARDNER DENVER NASH

CHARLEROI, PA. 15022, USA, AND

FROM GARDNER DENVER NASH LLC.

THE GARDNER DENVER NASH LLC,

DO NOT USE THIS PRINT FOR

CONSTRUCTION UNLESS

CERTIFIED AND DATED.

SHEET

SIZE:

D

DATE:

KERR PUMP AND SUPPLY

BLUE SKIES ENERGYUSER:

P.O.#:

NETWORK#:

SALES#:

P192004

5939175

5920915

06/2025

SHEET

0.06

- TOLERANCES -

REPRODUCE THE INFORMATION CONTAINED HEREIN IN CONNECTION WITH THE CUSTOMER'S

0.13

MOUNTING HOLES

INCHES

1.6

PERMISSION IS HEREBY GIVEN TO ANY GARDNER DENVER NASH CUSTOMER TO USE AND

THIS DRAWING CONTAINS PROPRIETARY INFORMATION OF GARDNER DENVER NASH LLC.

DIMENSIONAL UNITS ARE:

0.25 0.50

12.7

2-IN NPS2-IN NPS

PIPE CONNECTION LOCATIONS

6.4

GENERAL

0.13

3.2

MOUNTING HOLES

4 STAGES 4 STAGES

805RSF815

A

OUTLINE 853-GDGI 1-2 324TS E10

RWG

X

ASL/GNP

RELEASED. C/M 1187126 6/24/25

REVISION

REV DESCRIPTION DATE APPVD

(4) n3.00 HOLES

36.31

[922]

1.13

[29]

VIBRATION PADS

17.63

[448]

5.37

[136]

30.81

[783]

(4) n0.94 HOLES

29.60

[752]

72.00

[1829]

0.52

[13]

GAP

43.46

[1104]

65.00

[1651]

3.50

[89]

8.12

[206]

36.31

[922]

18.75

[476]

2.00

[51]

24.00

[610]

18.00

[457]

12.00

[305]

26.12

[663]

4.75

[121]

12.57

[319]

BLOWER DATA

MODEL NO.:

LUBRICATION:

INLET POSITION:

OUTLET POSITION:

DRIVE SHAFT POSITION:

853-GDGI

GREASE

INLET

TEFC

HERTZ:

VOLTAGE:

ENCLOSURE:

324TS

MOTOR DATA

FRAME:

HORSEPOWER:

PHASE: 3

COUPLING MFG.: REX OMEGA

COUPLING SIZE: E10

GAP: .52"

DIRECT DRIVE DATA

TOTAL ESTIMATED WEIGHT:

484 lb

≈2,434 lb

610 lb

1,340 lb

MOTOR:

BLOWER:

BASE/PEDESTAL:

BLOWER DATA

NOTES

1. DIMENSIONS SHOWN IN INCHES AND [mm].

2. DO NOT BOLT DOWN IF STUDS ARE USED TO

POSITION THE MACHINE, DO NOT FASTEN DOWN

WITH NUTS. NEVER GROUT BASE IN CONCRETE.

3. FLANGE DRILLING DIMENSIONS CONFORM TO

125 POUND ANSI CAST IRON FLANGED FITTINGS.

4. INERTIA - LB-FT² [KG-M²]32 [1.35]

R.P.M.: 3,600

44.87

[1140]

36.38

[924]

F L

O W

F L

O W

F L

O W

FLOW

F L

O W

FLOW

q INLET q OUTLET

3.62

[92]

19.81

[503]

11.88

[302] q ANCHOR HOLE OUTLET q q INLET

13.75

[349]

18.75

[476]

OUTLET q q INLET

64.88

[1648]

8" INLET FLANGE

8" OUTLET FLANGE

n13.50

[n343] n8.00

[n203] n11.75

[n298]

B.C.

DRILL & TAP

(8) 3/4-10 UNC HOLES

STRADDLE q

����������������������������� ������������ �!��"�#��$%&��#��� '�����%#()�*�&�+�,���"%#-���.((*/!��/�0�102/0���� 34$�##�0�� 5�(*!�6����-&�*����7��8�-�*��,�/9�0�:;3�-*�<���=�5�6>������/2/0�*�)+�7?@�AB�CDEFG�HB���B�B�EGE�� EFHID�J�KFDG� �EG�DL�KFDG�4�*�!%*���M�/2N� �@>7�O�*-#�*-#�* �@>7�O�P2�P2#�*5�Q�*%� �?>RO��6�>*-6�*-#>5 �>�R��PS�P2>'��0&/�T �>�O��*-#�6�U? A>A���P2�#U?)(>�V����W�$�0&�>�� �>?A��XYZ�*-#>5 A>?A@�PS�P2>'5��/���6�)(>�V���& A>�@R A>�@R����/�*����&>��6�Q�(�� �>��� �>��� HB���D[\ ]̂ I./� �>��4��N�0��_�$V̀ ��$��-�0��/�a/,��_�$+� �̀

Dbc��������L̂ ��ELGEd�]BIKE� �̂DHDFBI�KFDG� EFHID�J�KFDG� �EG�DL�KFDG�.#-/�0�����&&%�� À>7R7��)e. À>O���)e. A>�A�-����5�*��/9��V%#/,/�T A��f A��f A��f.#-/�0��Y�#(����%�� A���; A��>���; ?O>O@�$e0*������&&%�� _7��e0V�+ A�>�?��)e. _ÀR>̀��#-���2e0*���;*�< A����)$;4 �����e$;4 ?̀���#?�N�/&!N��2�����&&%�� �̀e0V�+ �>À��)e3 �>�A�-���2�EB�K�Ed�]BIKE� �̂DHDFBI�KFDG� EFHID�J�KFDG� �EG�DL�KFDG�Q;��)(��, ?�OO�5�4 ?�OO�5�4 ?�OO�5�4)%�2��;*�<�5��� ?̀��)$;4 �O?�e$;4 RÒ�#?�N)%�2�����&&%�� �R>AA�e0V�+ A>����)e3 �>�O�-���2���&&%���5/&�����)%�2� ��>AA�e0V�+ �>RA��)e3 �>�7�-���24�a>�Q�*>�Y%�0,�<0 OA>?7f OA>?7f OA>?7f���&&%���W���&/20 >̀���e0V�+ �>À��)e3 �>�A�-���2��<���W���&/20 ??>���V� ??>���V� �̀>OO�'M166/!/�0!T�W���&/20 �O>@�f �O>@�f �O>@�fY�#(����%���W���&/20 A?O>̀��; A?O>̀��; �@>�O�$

������������ !�� "#$%&%��'(� "#$)*��'(� "$*"��+��+,�-+��.��/!��0��1 "**2 "**2 "**2��������3��4��+�!�� "**�5 "**$**�5 6)$)7�8(�-������ !�� 9%*�(�/:; ":$<6��'(� 9"#&$#<���+��=(�-���5->? 7**�'85@ "*%7�(85@ "7"#��6ABC� DB+�=����� !�� #�(�/:; *$"#��'(E *$*"��+��=��������������� �F5C�'4��0 6"<%�,�@ 6"<%�,�@ 6"<%�,�@'!�=��5->?�,+�� 6)&�'85@ <*%�(85@ 7%*��6AB'!�=����� !�� 7$6:�(�/:; *$6*��'(E *$*:��+��=��� !���,� ���>�'!�=� #$6:�(�/:; *$"%��'(E *$*"��+��=@+G$�F>-$�3!��0>?� <:$%:2 <:$%:2 <:$%:2��� !���H�C� �=� #$**�(�/:; *$"#��'(E *$*"��+��=�>?���H�C� �=� ")$%#�/� ")$%#�/� "6$"%�IJKLL�D���D1�H�C� �=� <7$*)2 <7$*)2 <7$*)23��4��+�!���H�C� �=� "6)$:)�5 "6)$:)�5 <7$#7�8

������������ !�� "#$%&%��'(� "#$)*��'(� "$*"��+��+,�-+��.��/!��0��1 "**2 "**2 "**2��������3��4��+�!�� "**�5 "**$**�5 6)$)7�8(�-������ !�� 9:;�(�/:< "6$)&��'(� 9%:$:)���+��=(�-���5->? %**�'85@ )::�(85@ "::)��6ABC� DB+�=����� !�� "*�(�/:< *$6%��'(E *$*:��+��=��������������� �F5C�'4��0 ::#%�,�@ ::#%�,�@ ::#%�,�@'!�=��5->?�,+�� :&&�'85@ 6%*�(85@ %":��6AB'!�=����� !�� ":$*&�(�/:< *$##��'(E *$*6��+��=��� !���,� ���>�'!�=� :$*&�(�/:< *$*7��'(E *$*"��+��=@+G$�F>-$�3!��0>?� ;*$"#2 ;*$"#2 ;*$"#2��� !���H�C� �=� "*$**�(�/:< *$6%��'(E *$*:��+��=�>?���H�C� �=� %$)%�/� %$)%�/� ;$*#�IJKLL�D���D1�H�C� �=� ;)$762 ;)$762 ;)$7623��4��+�!���H�C� �=� ""&$"&�5 ""&$"&�5 #7$##�8

DATA SHEET

Three Phase Induction Motor - Squirrel Cage

Customer :

Product line : W22 NEMA Premium Efficiency Three-Phase

Product code : 12448181

Catalog # : 04036ET3E324TS-W22

Frame : 324/6TS Output : 40 HP (30 kW) Poles : 2 Frequency : 60 Hz Rated voltage : 230/460 V Rated current : 94.8/47.4 A L. R. Amperes : 597/298 A LRC : 6.3x(Code G) No load current : 27.0/13.5 A Rated speed : 3560 rpm Slip : 1.11 % Rated torque : 59.0 ft.lb Locked rotor torque : 229 % Breakdown torque : 240 % Insulation class : F Service factor : 1.25 Moment of inertia (J) : 4.90 sq.ft.lb Design : B

Locked rotor time : 39s (cold) 22s (hot) Temperature rise : 80 K Duty cycle : Cont.(S1) Ambient temperature : -20°C to +40°C Altitude : 1000 m.a.s.l.

Protection degree : IP55 Cooling method : IC411 - TEFC Mounting : F-1 Rotation¹ : Both (CW and CCW) Noise level² : 76.0 dB(A) Starting method : Direct On Line Approx. weight³ : 484 lb

Output 50% 75% 100% Foundation loads Efficiency (%) 91.7 92.4 92.4 Max. traction : 385 lb Power Factor 0.78 0.84 0.86 Max. compression : 869 lb

Losses at normative operating points (speed;torque), in percentage of rated output power P1 (0,9;1,0)

7.6 P2 (0,5;1,0)

5.4 P3 (0,25;1,0)

4.9 P4 (0,9;0,5)

4.2 P5 (0,5;0,5)

2.3 P6 (0,5;0,25)

1.5 P7 (0,25;0,25)

0.9 Drive end Non drive end

Bearing type : 6312 C3 6212 C3 Sealing : V'Ring V'Ring Lubrication interval : 12000 h 15000 h Lubricant amount : 21 g 13 g Lubricant type : Mobil Polyrex EM

Notes

USABLE @208V 101A SF 1.10 SFA 111A

This revision replaces and cancel the previous one, which must be eliminated.

(1) Looking the motor from the shaft end.

(2) Measured at 1m and with tolerance of +3dB(A).

(3) Approximate weight subject to changes after manufacturing process.

(4) At 100% of full load.

These are average values based on tests with sinusoidal power supply, subject to the tolerances stipulated in NEMA

MG-1.

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 1 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

Subject to change without notice

TORQUE AND CURRENT VS SPEED CURVE

Customer :

Product line : W22 NEMA Premium Efficiency Three-Phase

Product code : 12448181

Catalog # : 04036ET3E324TS-W22

Performance : 230/460 V 60 Hz 2P Rated current : 94.8/47.4 A Moment of inertia (J) : 4.90 sq.ft.lb LRC : 6.3 Duty cycle : Cont.(S1) Rated torque : 59.0 ft.lb Insulation class : F Locked rotor torque : 229 % Service factor : 1.25 Breakdown torque : 240 % Temperature rise : 80 K Rated speed : 3560 rpm Design : B

Locked rotor time : 39s (cold) 22s (hot)

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 2 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

LOAD PERFORMANCE CURVE

Customer :

Product line : W22 NEMA Premium Efficiency Three-Phase

Product code : 12448181

Catalog # : 04036ET3E324TS-W22

Performance : 230/460 V 60 Hz 2P Rated current : 94.8/47.4 A Moment of inertia (J) : 4.90 sq.ft.lb LRC : 6.3 Duty cycle : Cont.(S1) Rated torque : 59.0 ft.lb Insulation class : F Locked rotor torque : 229 % Service factor : 1.25 Breakdown torque : 240 % Temperature rise : 80 K Rated speed : 3560 rpm Design : B

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 3 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

THERMAL LIMIT CURVE

Customer :

Product line : W22 NEMA Premium Efficiency Three-Phase

Product code : 12448181

Catalog # : 04036ET3E324TS-W22

Performance : 230/460 V 60 Hz 2P Rated current : 94.8/47.4 A Moment of inertia (J) : 4.90 sq.ft.lb LRC : 6.3 Duty cycle : Cont.(S1) Rated torque : 59.0 ft.lb Insulation class : F Locked rotor torque : 229 % Service factor : 1.25 Breakdown torque : 240 % Temperature rise : 80 K Rated speed : 3560 rpm Design : B

Heating constant Cooling constant

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 4 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

THERMAL LIMIT CURVE

Customer :

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 5 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

VFD OPERATION CURVE

Customer :

Product line : W22 NEMA Premium Efficiency Three-Phase

Product code : 12448181

Catalog # : 04036ET3E324TS-W22

Performance : 230/460 V 60 Hz 2P Rated current : 94.8/47.4 A Moment of inertia (J) : 4.90 sq.ft.lb LRC : 6.3 Duty cycle : Cont.(S1) Rated torque : 59.0 ft.lb Insulation class : F Locked rotor torque : 229 % Service factor : 1.25 Breakdown torque : 240 % Temperature rise : 80 K Rated speed : 3560 rpm Design : B

Rev. Changes Summary Performed Checked Date

Performed by

Checked by Page Revision

Date 25/06/2025 6 / 6 This document is exclusive property of WEG S/A. Reprinting is not allowed without written authorization of WEG S/A.

Accessories

Paint Finish Centrifugal Products

All Nash facilities are ISO 9001 certified.

Gardner Denver Nash PO Box 130, Bentleyville, PA 15314

Phone: +1 800-982-3009 / +1 724-239-1500

Fax: +1 724-239-1502 E-mail: info.HoffmanLamson@gardnerdenver.com

Web: www.HoffmanandLamson.com

© 2015 Gardner Denver, Inc.

07/2015 Page 1 of 1 CF0875002 Vs 04

PRODUCT NOTES

DESCRIPTION TEST RESULTS

PROPERTIES SUMMARY

1. Information is approximate, subject to change without notice, and not for construction use unless certified

2. Standard color is GDI Revolution Blue.

VOC Compliant, Acrylic Polyurethane Paint with an Epoxy Primer

2-part, high building, high solid content, coating that provides a high gloss finish

Excellent resistance to UV light, chemicals, corrosion, heat, and abrasion

Excellent chemical and wear resistance for virtually any blower application

Virtually non-removable from a surface prepared using standard substrate cleaning practices

Available in many colors at an additional charge provided a sample for custom matching is supplied

TOTAL SOLIDS (% by volume): 59-63 (primer)

69-73 (paint)

REDUCTION: None

VOC: 1.9 pounds per gallon

DRY APPLICATION

THICKNESS CAST PARTS: 2.0-4.0 mils (Primer)

THICKNESS CAST PARTS: 3.0-5.0 mils (Top Coat)

DRY APPLICATION

THICKNESS STEEL PARTS: 3.0-5.0 mils

TEMPERATURE RESISTANCE: 200 °F continuous

ADHESION: ASTM D4541, 1200 PSI

PENCIL HARDNESS: ASTM D3363, 3H

IMPACT RESISTANCE: ASTM D2794, >140 Pounds

FLEXIBILITY: ASTM D522, 3/8 Inch Mandrel, 10.7%

WEATHERING: ASTM D4587, QUV-A, 3,000 Hours

SALT SPRAY TESTING: Exceeds 2,000 hour requirements

CROSS HATCH:

Scribe Undercutting: Less than 1 millimeter from scribe

Blistering: Absent

Rust staining: None

Carboguard® 8922 LH

December 2011 8927

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboguard® are registered trademarks of Carboline Company.

Selection & Specification Data Generic Type Cross-linked epoxy

Description Carboguard 8922 LH is a versatile corrosion resistant coating. May be topcoated with itself, or a broad variety of high performance finish coats. Carboguard 8922 LH has surface tolerant properties. Specially formulated to meet current Federal guidelines for HAPS content.

Features • Ready to apply after mixing; no sweat-in time or thinning required

• Economical fit for use epoxy

• Used as a primer or intermediate coat

• Can be applied over power tool cleaned surfaces

• Wet on wet application at 75° F (24°C) substrate temperature

• Acceptable over iron phosphate preparation

• Low HAPS of 1.85 pounds/solid gallon

Color Primer color (0700) gray

Finish Satin

Dry Film Thickness

2.0 - 4.0 mils (51 - 102 microns) per coat

Solids Content By Volume 61% +/- 2%

Theoretical Coverage Rate

978 ft2 at 1 mil (24 m2/l at 25 microns)

489 ft2 at 2 mils (12 m2/l at 50 microns)

245 ft2 at 4 mils (6 m2/l at 100 microns)

Allow for loss in mixing and application.

VOC Values As Supplied 2.79 lbs./gal 334 g/l

Thinned: 12 oz/gal w/ #72: 3.21 lbs/gal (384 g/l) These are nominal values and may vary slightly with color.

Dry Temp.

Resistance

Continuous: 200 °F (93 °C) Non-Continuous: 250 °F (121 °C)

Discoloration and loss of gloss is observed above 200 F (93 C).

Limitations Epoxies lose gloss, discolor and eventually chalk in sunlight exposure. Not recommended for immersion service.

Topcoats May be coated with Acrylics, Epoxies, Alkyds, or Polyurethanes depending on exposure and need.

Substrates & Surface Preparation General Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.

Steel Also acceptable over SSPC-SP2 and over blasted steel (SSPC-SP6) with a low 1-2 mil blast profile.

Phospatized Steel For most applications: apply 8922 LH directly to dry, properly phosphatized substrate. Perform adhesion tests to ensure proper, uniform and acceptable adhesion direct to the phosphatized metal substrate.

Performance Data Test Method System Results

Adhesion

(ASTM D4541)

Carboguard 8922 LH @1.9 mils

1200 psi average (cohesive failure)

Elongation/Flexibility

(ASTM D522)

Carboguard 8922 LH @3.3 mils

Conical Mandrel:

3/8" diameter;

10.7% Elongation Salt Fog (ASTM B117) Carboguard 8922 LH /

Carbothane 134 HG over Grit blasted steel

1500 hours: Plane, #8/6 Few blisters;

Scribe, #6 Few blisters, Rust in scribe

Salt Fog (ASTM B117) Carboguard 8922 LH / Carbothane 134 HG over Phosphatized steel

500 hours; Plane, No Effect; Scribe, Rust in Scribe only

Mixing & Thinning Mixing Power mix separately, then combine and power mix.

DO NOT MIX PARTIAL KITS.

Thinning Normally not required but may thin as follows:

Spray: Up to 12 oz/gal (10%) w/ #72.

Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied.

Ratio 1:1 Ratio (A to B)

Pot Life 3 Hours at 75°F (24°C) Pot life ends when coating loses body and begins to sag. Pot life times will be less at higher temperatures.

Application Equipment Guidelines Listed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results.

Spray Application (General)

The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco.

Conventional Spray

Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .070” I.D. fluid tip and appropriate air cap.

Airless Spray Pump Ratio: 30:1 (min.)* GPM Output: 2.5 (min.)

Material Hose: 3/8” I.D. (min.)

Tip Size: .015”-.019” Output PSI: 2100-2300 Filter Size: 60 mesh *Teflon packings are recommended and available from the pump manufacturer.

Brush & Roller (General)

Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid excessive re-brushing or re-rolling. For best results, tie-in within 10 minutes at 75°F (24°C).

Brush Use a medium bristle brush.

Roller Use a short-nap synthetic roller cover with phenolic core.

Carboguard® 8922 LH

December 2011 8927

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboguard® are registered trademarks of Carboline Company.

Application Conditions Condition Material Surface Ambient Humidity Minimum 50 °F (10 °C) 50 °F (10 °C) 50 °F (10 °C) 0% Maximum 90 °F (32 °C) 125 °F (52 °C) 110 °F (43 °C) 80%

This product simply requires the substrate temperature to be above the dew point. Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate. Special application techniques may be required above or below normal application conditions.

Curing Schedule Surface Temp.

& 50% Relative

Humidity

Dry to Handle Dry to Recoat Maximum Recoat Time

50 °F (10 °C) 12 Hours 30.0 Minutes 1.0 Years 60 °F (16 °C) 6 Hours 10.0 Minutes 1.0 Years 75 °F (24 °C) 3 Hours 5.0 Minutes 1.0 Years 90 °F (32 °C) 2 Hours 3.0 Minutes 1.0 Years

These times are based on a 1.5-2.0 mil (37.5-50 micron) dry film thickness for non-immersion.

Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discoloration and may result in a surface haze. Any haze or blush must be removed by water washing before recoating. If the maximum recoat times have been exceeded, the surface must be abraded by sweep blasting or sanding prior to the application of additional coats. For force curing, contact Carboline Technical Service for specific requirements.

Cleanup & Safety Cleanup Use #2 Thinner or Acetone. In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety Read and follow all caution statements on this product data sheet and on the MSDS for this product.

Employ normal workmanlike safety precautions.

Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.

Ventilation When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured. The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used. User should test and monitor exposure levels to insure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved respirator.

Caution This product contains flammable solvents. Keep away from sparks and open flames. All electrical equipment and installations should be made and grounded in accordance with the National Electric Code. In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes.

Packaging, Handling & Storage Shelf Life Part A & B: Min. 24 months at 75°F (24°C)

*Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers.

Shipping Weight (Approximate)

2 Gallon Kit - 26 lbs. (12 kg) 10 Gallon Kit - 127 lbs. (58 kg)

Storage Temperature & Humidity

40° - 110°F (4°- 43°C) 0-100% Relative Humidity

Packaging, Handling & Storage Flash Point (Setaflash)

Part A: 74°F (23°C) Part B: 70°F (21°C)

Carbothane® 8845

September 2014 8845

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline and Carbothane are registered trademarks of Carboline Company.

Selection & Specification Data

Generic Type Two component, acrylic, aliphatic polyurethane.

Description Carbothane 8845 is a fast dry, high solids, low VOC, high gloss, high build, two component polyurethane coating. Carbothane 8845 exhibits the excellent dry times and handling characteristics required by Original Equipment Manufacturers.

This coating has outstanding hardness, adhesion and resistance to: impact, marring, abrasion, chemicals and staining. Carbothane 8845 is recommended as a direct to metal finish coat or as a finish coat over properly primed substrates.

Typical applications include air compressors, propane tanks, trailer chassis and frames, valves, pumps, waste water treatment plant equipment, agricultural equipment, hazardous material storage buildings and general industrial equipment. Not recommended for continuous immersion service.

Features • VOC compliant – 1.9 lbs/ gal as supplied

• Direct-To-Metal (DTM)

• Fast Dry – 7-8 hours to handle at 75°F

• High solids, high build, high gloss

• Excellent abrasion resistance

• Application by conventional, airless spray, HVLP or electrostatic

• Excellent chemical resistance

• Ambient air or force cure with conventional or infrared ovens

Color Wide variety of custom colors

Finish High Gloss

Primers Self-priming, epoxy, zinc rich epoxy or as recommended by Carboline

Dry Film Thickness

3 – 5 mils per coat (75-125 microns).

Solids Content

By Volume: 71% ± 2%

Theoretical Coverage Rate per Gallon

379 ft at 3 mils (75 microns)

284 ft at 4 mils (100 microns)

227 ft at 5 mils (125 microns)

Mixing and application losses will vary and must be taken into consideration when estimating job requirements.

HAPS Value 0.54 lbs/solid gallon

VOC Values

Ratio By Volume

Pot Life

As supplied: 1.9 lbs/gal (228 g/l) Thinned:

6 oz/gal w/ #76: 2.1 lbs/gal (252 g/l) These are nominal values.

4:1 Ratio 4 parts Carbothane 8845 Part A 1 part Carbothane 8843 Converter Part B

90 min at 75°F (24°C) unthinned Pot life decreases at higher temperatures. Pot life ends when coating becomes too viscous to use.

This product is moisture sensitive. Avoid moisture contamination.

Dry Temp.

Resistance

Continuous: 200°F (93°C)

Non-Continuous: 250°F (121°C)

Discoloration is observed above 180°F (82°C).

Substrates & Surface Preparation

General Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.

Steel Abrasive blast to a commercial finish in accordance with SSPC-SP6 and obtain a 1½ - 2 mil (35-50 micron) blast profile.

Phosphatize Apply 8845 directly to dry, properly phosphatized substrate. Perform adhesion tests to insure proper, uniform and acceptable adhesion of 8845 direct to phosphatized metal substrate.

Primed Surfaces

Remove any oil or grease from the surface to be coated with Thinner #2 or Carboline Surface Cleaner #3 (Refer to Data Sheet) in accordance with SSPC-SP1.

Typical Chemical Resistance

Exposure

Splash & Spillage Fumes

Acids Very Good1 Excellent

Alkalies Very Good1 Excellent

Solvents Very Good2 Excellent

Salt Excellent Excellent

Water Excellent Excellent

1. Certain colors may discolor.

2. Resistance may vary dependent on the type of solvent involved.

Curing Schedule

Ambient, Material &

Surface Temp

Dry to Touch

Dry to Handle or Assemble

Dry to Full Cure

75°F (24°C) 90-120 minutes

7-8 hours 7-14 days

These times are based on a 4.0 mil (100 micron) dry film thickness.

Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure. Note: Product may be force cured.

FORCE CURE INFORMATION

Oven Temperature at 150°F (66°C)

Flash Time is 20 minutes.

Oven Dwell Time 45 minutes.

Cool Down is 10 minutes.

Oven Temperature at 180°F (82°C)

Flash Time is 20 minutes.

Oven Dwell Time 30 minutes.

Cool Down is 10 minutes.

Carbothane® 8845 Carboline 8000 Series has been specifically designed for OEM applications.

For specific product requirements or process painting recommendations contact Carboline OEM Engineered Finishes Division.

September 2014

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline and Carbothane are registered trademarks of Carboline Company.

Application Equipment Listed below are general equipment guidelines for the application of this product.

Job site conditions may require modifications to these guidelines to achieve the desired results.

General Guidelines:

Spray Application (General)

The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco.

Conventional Spray

Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .070” I.D. fluid tip and appropriate air cap.

Airless Spray Pump Ratio: 30:1 (min.)

GPM Output: 3.0 (min.)

Material Hose: 3/8” I.D. (min.)

Tip Size: .013-.017” Output PSI: 2500-3500 Filter Size: 60 mesh

Teflon packings are recommended and available from the pump manufacturer.

Electrostatic Contact Carboline for specific equipment recommendations.

HVLP Contact Carboline for specific equipment recommendations.

Touch Up Respray or brush. Brushing recommended only for touchup of small areas. Use natural bristle brush applying with full strokes.

Mixing & Thinning

Mixing For plural component application equipment follow the equipment manufacturer’s instructions.

For batch mixing, power mix part A separately, then combine and power mix thoroughly in the following proportions:

THIS PRODUCT IS MOISTURE SENSITIVE.

AVOID MOISTURE CONTAMINATION. DO NOT

MIX PARTIAL KITS.

Ratio 4:1 Ratio (A to B) 1 Gallon Kit 5 Gallon Kit

8845 Part A .8 gallons

(in 1 gallon can)

4 gallons (in 5 gallon can) Urethane

Converter

25.6 fluid ozs. 1 gallon

Thinning Normally not required. May be thinned up to 6 oz/gal (5%) with #76. Thinner #97, #214, or #215 may be used when applying 8845 in very hot conditions or longer working time is required.

Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied.

Pot Life 90 minutes at 75°F (24°C).

Application Conditions

Condition Material Surface Ambient Humidity

Normal 60°-85°F

(16°-29°C)

60°-85°F

(16°-29°C)

60°-85°F

(16°-29°C) 40-60%

Minimum 50°F

(10°C)

35°F

(2°C)

35°F

(2°C) 10%

Maximum 130°F

(54°C)

120°F

(50°C)

95°F

(35°C) 80%

Industry standards are for substrate temperatures to be 5°F (3°C) above the dew point.

Application Conditions Cont.

Caution: This product is moisture sensitive in the liquid stage and until fully cured. Protect from high humidity, dew and direct moisture contact until fully cured. Application and/or curing in humidities above maximum, or exposure to moisture from rain or dew may result in loss of gloss and/or microbubbling of the product.

Cleanup & Safety

Cleanup Use Thinner #2 or Acetone. In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety Read and follow all caution statements on this product data sheet and on the MSDS for this product. Employ normal workmanlike safety precautions. Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.

Ventilation When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured. The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used. User should test and monitor exposure levels to insure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator.

Caution This product contains flammable solvents. Keep away from sparks and open flames. All electrical equipment and installations should be made and grounded in accordance with the National Electric Code. In areas where explosion hazards exist, workmen should be required to use non-ferrous tools and wear conductive and non-sparking shoes.

Packaging, Handling & Storage

Shipping Weight 8845 (Approximate)

1 Gallon Kit 15 lbs. (6 kg)

5 Gallon Kit 58 lbs. (22 kg)

Thinner 76 8 lbs. (4 kg) 41 lbs. (19kg) Thinner 97 8 lbs. (4 kg) 41 lbs. (19kg)

Carbothane 8845 is also available in drum quantities.

Flash Point (Setaflash) Part A: 63°F (17°C)

Part B: 62°F (17°C) Thinner 76: 21°F (-6°C)

Storage (General) Store Indoors.

Storage Temperature & Humidity

40° - 110°F (4-43°C) 0-80% Relative Humidity

Shelf Life Part A: Min. 36 months at 75°F (24°C)

Part B: Min. 24 months at 75°F (24°C)

*Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers.

Accessories Isolation Base Pads

Centrifugal Products

PERFORMANCE SPECIFICATIONS MATERIALS OF CONSTRUCTION

TEMP. RANGE: -76° F to 212° F (-60° C to 100° C) LOAD RATING: 50 lbs-force / in2 (3.5 kgs-force / cm2)

ELASTOMER: SBR/NBR Rubber CORK: Cork permanently bonded between

2 layers of ribbed-tread design elastomer

PART NO.

(in) (cm)

B

(in) (cm)

C

(in) (cm)

Area (in2) (cm2)

Max. Load/Pad (lbs-force) (kgs-force)

HF00896814 3.0 7.6 3.0 7.6 0.9 2.2 9.00 58 450 203

VP1003583 1.5 3.8 1.5 3.8 0.9 2.2 2.25 14 113 51

VP1003005 4.0 10 4.0 10 0.9 2.2 16.00 103 800 362

VP1003074 6.0 15 6.0 15 0.9 2.2 36.00 232 1800 815

VP1003778 8.0 20 8.0 20 0.9 2.2 64.00 412 3200 1450

BB1249724 3.0 7.6 3.0 7.6 1.125 2.86 9.00 58 450 203

BB1249726 1.5 3.8 1.5 3.8 1.125 2.86 2.25 14 113 51

BB1249727 4.0 10 4.0 10 1.125 2.86 16.00 103 800 362

BB1249725 6.0 15 6.0 15 1.125 2.86 36.00 232 1800 815

BB1249728 8.0 20 8.0 20 1.125 2.86 64.00 412 3200 1450

PRODUCT NOTES

1. Information is approximate, subject to change without notice, and not for construction use unless certified

Gardner Denver Nash 200 Simko Boulevard, Charleroi, PA 15022 Phone: +1 724-239-1500 Fax: +1 724-239-1502 Web: www.HoffmanandLamson.com

05/2024 Page 1 of 1 CF0365001 Vs 10

All Nash facilities are ISO 9001 certified.

© 2024 Gardner Denver, Inc.

GNP2101

Rectangle

NUMBER:

PAGE:

N132

COMMERCIAL PARTS VERSION: 01

EFFECTIVE: 04-14-08

GUARD-COUPLING N132

TITLE: GUARD-COUPLING

VENDOR: REXNORD - FALK

TYPE: ORANGE PEEL CCG

GENERAL: HDPE PLASTIC, A2/304 FASTENERS, GUARDS ARE HINGED, AND "PEEL" OPEN FOR

CONVENIENT COUPLING LUBRICATION, INSPECTION, MAINTENANCE. IN ADDITION,

GUARDS ASSURE COMPLIANCE WITH OSHA, ASME, AND ANSI STANDARDS.

GUARD DIMENSIONS -- INCHES

Gardner Denver Part No.

Size A B C D E F G H I J K L M N O P Q R S T

51M2 20 12.00

6.00

11.00

4.00

5.50

9.50

4.75

1.25

11.15

0.25

8.00

0.50

12.00

5.75

12.25

6.13

4.50

11.25

51M3 30 18.00

9.00

13.50

5.00

13.25

6.63

3.88

15.50

0.31

9.50

16.75

18.00

6.50

16.50

7.00

51M4 40 23.00

11.50

16.50

10.50

17.00

8.50

19.25

20.50

10.00

21.50

20.00

51M5 50 27.00

13.50

19.50

7.50

13.25

21.00

7.38

23.25

14.25

24.50

26.50

14.50

10.00

24.50

Notes:

Extension clips are not required for B1/B2 minimum condition.

Nominal material thickness is .13 in. (3.3mm) size 10, .19 in.

(4.8mm) size 20/30, .250 in. (6.4mm) size 40/50.

† Requires a minimum 1/2 shaft dia. clearance in each direction for guard removal or installation.

Hinge Detail

Clip Detail

TremPro® 644 RTV

General Purpose Silicone Sealant

0815/TPRO644RTVDS-ST

Please refer to our website at www.tremcosealants.com for the most up-to-date Product Data Sheets.

Tremco Commercial Sealants & Waterproofing

3735 Green Rd Beachwood OH 44122

216.292.5000 / 800.321.7906

1451 Jacobson Ave Ashland OH 44805

419.289.2050 / 800.321.6357

220 Wicksteed Ave Toronto ON M4H1G7

416.421.3300 / 800.363.3213

1445 Rue de Coulomb Boucherville QC J4B 7L8 514.521.9555 www.tremcosealants.com Page 1 of 1

Product Description

TremPro® 644 RTV is a one-part, general purpose, acetoxy silicone sealant.

Basic Uses

TremPro 644 RTV is specially designed for sealant joints between most non-porous materials such as glass, aluminum, metal and metal alloys. Industrial and residential uses include HVAC, plumbing and kitchen/bath fixtures.

TremPro 644 RTV may also be used on site where a gun-grade sealant is required.

Features and Benefits

Easily gunnable over a wide range of temperatures and has excellent adhesion to most common substrates without the use of a primer.

TremPro 644 RTV skins within 30 min at 75 °F (24 °C) and 50% RH, and cures into a tough, durable, weather resistant material.

It has excellent handling characteristics and tools to a smooth, attractive finish.

TremPro 644’s superior skin time makes it ideal for OEM and production line uses.

Versions of TremPro 644 RTV containing fungicide for sanitary applications are available.

Packaging

10.1-oz (300-mL) cartridges

Colors

Clear, White, Dark Bronze, Almond, Black and Aluminum.

Availability

Immediately available from your local Tremco Field Representative, Tremco Distributor or Tremco Warehouse.

Limitations

Do not apply over damp or contaminated surfaces.

Use with adequate ventilation.

Do not use on surfaces sensitive to corrosion by acetic acid vapors (a by-product of sealant cure).

Substrate Preparation

For good adhesion, the joint surface must be sound, clean and dry.

Depending on the substrate, the joint surface may require a thorough wire brushing with a steel wool or Scotch Brite pad and/or solvent wipe.

Application

Cartridges of TremPro 644 RTV silicone are easy to apply with conventional caulking equipment. Fill joint completely and tool.

Damaged sealant can be repaired. Consult Tremco Technical Services or your local Tremco Sales Representative for repair procedures.

Clean Up

Tooling is recommended immediately after application to ensure firm, intimate contact with the joint interface. Dry tooling is preferred. Excess sealant and smears adjacent to the joint can be removed with IPA or MEK before sealant cures.

Warranty

Tremco warrants its Products to be free of defects in materials, but makes no warranty as to appearance or color. Since methods of application and on-site conditions are beyond our control and can affect performance, Tremco makes no other warranty, expressed or implied including warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE, with respect to Tremco Products. Tremco’s sole obligation shall be, at its option, to replace, or refund the purchase price of the quantity of Tremco Products proven to be defective and Tremco shall not be liable for any loss or damage.

TYPICAL PHYSICAL PROPERTIES

PROPERTY TEST METHOD TYPICAL VALUES

100% Modulus 50 to 80 psi

Cure Time (1/8” thickness) 24 hr

Sag Resistance 0 to 0.4 mm

Service Temperature -40 to 400 ˚F (-40 to 204 ˚C)

Shore A Hardness ASTM C661 17 to 21

Tack Free Time 30 min

Tensile Strength 200 to 250 psi

Please refer to our website at www.tremcosealants.com for the most up-to-date Product Data Sheets.

http://www.tremcosealants.com/

Version: 2.2 Revision Date: 01/27/2022

000000008481

1/19

SAFETY DATA SHEET

1. Identification

Material name: TREMPRO 644 RTV WHITE 3" - 12 CTG CS Material: 6445065F312

Recommended use and restriction on use

Recommended use: Sealant Restrictions on use: Not known.

Manufacturer/Importer/Supplier/Distributor Information Tremco U.S Sealants 3735 Green Road Beachwood OH 44122

US

Contact person: EH&S Department Telephone: 216-292-5000 Emergency telephone number: 1-800-424-9300 (US); 1-613-996-6666 (Canada)

2. Hazard(s) identification

Hazard Classification

Health Hazards

Acute toxicity (Dermal) Category 4

Acute toxicity (Inhalation - dust and mist)

Category 4

Carcinogenicity Category 1A

Unknown toxicity - Health

Acute toxicity, oral 76.08 %

Acute toxicity, dermal 80.48 %

Acute toxicity, inhalation, vapor 100 %

Acute toxicity, inhalation, dust or mist

92.5 %

Environmental Hazards

Acute hazards to the aquatic environment

Category 3

Chronic hazards to the aquatic environment

Category 3

Unknown toxicity - Environment

Acute hazards to the aquatic environment

86.08 %

Chronic hazards to the aquatic environment

86.08 %

2/19

Hazard Symbol:

Signal Word: Danger

Hazard Statement: Harmful in contact with skin or if inhaled.

May cause cancer.

Harmful to aquatic life with long lasting effects.

Precautionary Statements

Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face protection. Use personal protective equipment as required.

Response: IF ON SKIN: Wash with plenty of soap and water. Wash contaminated clothing before reuse. Call a POISON CENTER or doctor/ physician if you feel unwell. Specific measures (see supplemental first aid instructions on this label). IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF exposed or concerned: Get medical advice/attention.

Storage: Store locked up.

Disposal: Dispose of contents/ container to an approved facility in accordance with local, regional, national and international regulations.

Hazard(s)…