K3 - Campuswide Interior Glazing PD _ Samples Resubmittal_Part1.pdf

RETURN OF SUBMITTAL

Title Or Description Date: Spec. Section:

Camous Wide Interior Glazina 41

J4 08 80 00 Contractor's Name and Address Station Location:

Chris Bantner 13611 East Colfax Ave.

Aurora, CO 80045

Kiewit-Turner. a Joint Venture Contract No: Proiect No:

13611 East Colfax Avenue VA1 01 F-i 5-C-0005 554-501 Aurora, CO 80045 Transmittal Date: VA File No:

3/20/2015 08 80 00 - 005- Ri

Submittal Scope Sample review

Submittal Items Acted Upon

Submittal Item Status

001 - Campus Wide Interior Glazing AN- Approved as Noted

Supplier or Manufacturer Submittal Type

Physical Sample Notes/Comments

1) See comments below for glass types referenced I included in resubmittal documentation; refer to submittal comments for additional information;

GL08: glass and product data previously approved. Resubmittal inclusive of proposed sealer. [Note: due to minimal (by manufacturer's design) thickness (2 molecules per product documentation), Manufacturer to provide certification of factory application as part of glazing provision.]

GL09 - product same as GL16 and acceptable (prior product approval via (VA) RFI 5140.

GL13 - Backpainting color matching P12 is acceptable to JVT. Lettering color and typeface incorrect.

Coordinate with signage drawings and resubmit.

GL14 - sample included as part of resubmittal, but reviewer unclear as to reason. GL14 Product data identified as submitted but not found as part of this submittal. Clarify / resubmit as necessary with explanatory information.

GL16 - product same as GL09 and acceptable (prior product approval via (VA) RFI 5140. 2) GL07 mini-blind color selection: 0157 "Silver".

Any questions, contact James Chang

Signature of Authorizing Official

'Dte

Received 04/15/2015

Fax: 303.930.9001

303.930.9000Tel:

Kiewit - Turner a Joint Venture

Suite A-300 7200 S. Alton Way

Englewood, CO 80112

Job: 15387 - Replacement Medical Center Facility

Product Data

Sample

Other

Shop Drawing

Resubmittal

First Submittal X

VA Proj #:

To: H+L Architecture 1755 Blake Street

Suite 400

Denver, CO 80202

DESCRIPTIONSpecificationSUBMITTAL

ItemQuantity Section Sub./SupplierNo. Mfgr.

ACTION

DCBA E

Kiewit Submittal No. 22 13 00-01 Architect's Submittal No. 00008

Review Cycle: 001

Attn: Chuck Adkisson

1 SWPPP - CBS & RFP #3 OnlyKiewit - Turner a

Joint Venture

01 573

ACTION TAKEN

CONTRACTOR'S SIGNATURE:

CONTRACTOR'S NOTES:

DATE: 7/12/2011

Reviewed Only for Revisions to

Reviewed: Incorporate Changes

Reviewed=

A

B

C

Previous Submittal

Revise and Resubmit=D

Rejected =E

ARCHITECT/ENGINEER RESPONSE:

REMARKS:

BY: DATE:

Expedition f_sb_pks_01a

VA101CFM-C-0100

Cc: Tim Pogany, U.S. Dept. of Veterans Affairs

Received By ___________________

Date _______________

08 80 00

X

Campus_Wide_Interior_Glazing_PD _&_Samples_Resubmittal

X

EWS

08 80 0005R1

03/20/2015

04/10/2015

Kiewit-Turner Submittal No.

VA 1

JVT 3

REQUESTED RETURN DATE:

Kevin Lindsey, U.S. Dept. of Veterans Affairs

VA101F-15-C-0005

RECEIVED

By VHAECHMayC at 12:19 pm, 4/13/15

08 80 00-05R1

3/20/2015

This Submittal Contains Bookmarks

3/20/2015

08 80 00-05R1

H+L / RJ SOM / SG

4/9/2015

3/5/2015

VA/JVT Response Needed:

VA/JVT Response Needed:

Use of GL 16 in accordance with RFI 5140 response;

product previously approved for use in CBS (Building 10).

Presence of GL 14 sample in this submittal is not understood by JVT reviewer. No GL 14 product data located.

Tempered Glass is one of the most utilized and cost-effective architectural safety glass options available. For over six decades, we've built a business on perfecting an industry trade: Our fine-tuned thermal tempering process allows us to provide world-class high- performance glass at a very competitive price. Call us to learn more.

What is Tempered Glass?

Fully-Tempered Glass is achieved when annealed float glass undergoes a specific thermal tempering process that includes uniformly heating the glass, typically at a furnace temperature of 1150° F (621° C), and then rapidly cooling or "quenching" the lite by blowing an even distribution of cool air simultaneously on both surfaces. This process creates outer layers of high compression at the surfaces and a compensating tension zone in the core of the glass lite.

This process of thermal manipulation both toughens the glass lite and significantly decreases the risk of injury during glass breakage. Due to its high compression levels, tempered glass shatters into many small, blunt pieces rather than breaking into large, sharp shards, which are most responsible for serious glass injuries. The thermal tempering process also renders the lite four times stronger than annealed float glass, and two times stronger than heat-strengthened glass--another type of heat-treated material. It is because of these properties that tempered glass satisfies safety codes set by American National

Standards Institute(ANSI) Z97.1 and Consumer Products Safety Commission16 CFR 1201, which mere heat-strengthened glass do not fulfill.

Our six decades of mastery in glass tempering allows us to fill the growing demand for our exceptional range of product lines:

Table Tops

Shower Enclosures

Doors and Entry Systems

We draw from years of experience to maximize efficiency and custom fabrication expertise, which is why we can offer over seventy variations of glass sizes and types in both annealed and tempered options, without much difference in price for either alternative.

Call us and see just how competitive our pricing is. Ask us about our deals for local businesses in our region and packages for first-time clients.

Tempered Glass

(888) 789-7810 Se habla Español

Sign up · Login

Products Support Credit Photos News About Contact

Spec:88000

1.5D, 2.2A

GL01

Type your email address here

FOR REFERENCE

ONLY. PREVIOUSLY

SUBMITTED/APPROVED

UNDER 08 80 00-05.

Home | Products | Support | Photos | News | Blog | About | Contact | Partners | Locations | Careers

Recent News Glasswerks Launches Colorwerks Glasswerks Boasts the Most Eco-Friendly Production of Double-Coated Colored Glass in the U.S. Market Colorwerks Glass by Glasswerks FOR IMMEDIATE ...

Glasswerks Unveils Suite ...

Now Available: Customer Rewards Program, Online Customer Intranet, E-Newsletter, and Twitter Microblog FOR IMMEDIATE RELEASE Sep 07, 2010 - SOUTH ...

See all News

Testimonials "I love Glasswerks. I only use

Glasswerks glass."

- Greg Holder, Glass Artist

"We are very proud of our accomplishments [at PH Towers in

Vegas] and express sincere gratitude to all at Glasswerks for their tireless attention to detail."

- Dan Davis, Owner, Davis Glass

Twitter

“Our goal is to provide the highest customer satisfaction by doing each and every task correctly the first time… every time.”

Copyright © 2009-2011 Glasswerks LA, Inc

Spec:88000

1.5D, 2.2A

GL01

FOR REFERENCE

ONLY. PREVIOUSLY

8600 Rheem Avenue, South Gate, California 90280 ! Toll Free (888) 789-7810 ! Fax: (888) 789-7820 http://www.glasswerks.com ! E-mail:glasswerks@glasswerks.com

June 3, 2014

MOUNTAIN VALLEY GLASS

4964 S.REDWOOD RD.

TAYLORSVILLE, UT 84123

ASTM Certification

This letter will confirm that the glass furnished to Mountain Valley Glass will meets or exceeds all requirements set forth in Consumer Products Safety Commission Specification CPSC 16 CFR 1201 and American Society for Testing and Materials Specifications ASTM C1036-90 and

ASTM C1048-92.

Please call me personally if you should need further clarification.

Sincerely, Rhonda Heckard Glasswerks

Spec:88000

1.5D, 2.2A

GL01

ASTM Certification

Safety Commission Specification CPSC 16 CFR 1201 and American Society for Testing and Materials Specifications ASTM C1036-90 and Society for Testing and Materials Specifications ASTM C1036-

ASTM C1048-92.

Submit documentation indicating Kind, Condition, Type, Class and Quality as noted in specification.

FOR REFERENCE

ONLY. PREVIOUSLY

8600 Rheem Avenue n South Gate, Ca. 90280 n Toll Free (888) 789-7810 n Fax: (888) 789-7820 http://www.glasswerks.com n E-mail:glasswerks@glasswerks.com

RE: Sample Lami Warranty

TEN (10) YEAR LIMITED LAMINATED GLASS WARRANTY

GLASSWERKS LA, INC., (hereinafter called "GLASSWERKS") provides this warranty with respect to it's laminated glass to XYZ Company (hereinafter called

"PURCHASER"), and to no other company or person, for the project info in California, Packing Slip # and # .

GLASSWERKS warrants to PURCHASER for a period of TEN (10) years from date of manufacture and under normal conditions, the laminated glass shall be free of manufacturing defects resulting in edge separation that materially obstructs vision through the glass surfaces. GLASSWERK'S liability shall be limited solely to its responsibilities under the Warranty. In no event shall GLASSWERKS be liable to any person or entity for indirect, special, incidental or consequential damages or charges for any reason.

CONDITIONS THAT WILL VOID THE WARRANTY

· If the Glass surfaces or panes are broken or fractured

· If the Laminated Glass is subjected to standing water or other liquids

· If the Laminated Glass product is damaged or altered by handling, storage, fabrication, or installation contrary to industry standards and incorporated by reference to GANA (Glass Association of North America) and AAMA (American Architectural Manufacturers Association) or equivalent

· If the Laminated Glass is attacked by incompatible glazing lubricants, glazing soaps, incompatible glazing gaskets, glazing sealants, incompatible cleaning fluids, moisture or building runoff, gluing or insulation, or exposure to solvent or chemical fumes

· If the Laminated Glass was discarded or destroyed

· If the Laminated Glass is installed in water craft, solar collectors, or commercial refrigeration products

· If the Laminated Glass PVB Interlayer is cut with the assistance of flammable liquids, either ignited or non-ignited

THIS LIMITED WARRANTY CONTAINED HEREIN IS IN LIEU OF ALL OTHER

WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH

WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. THIS WARRANTY MAY

Spec: 88000

1.5D, 2. A!

GL0"

FOR REFERENCE

ONLY. PREVIOUSLY

NOT BE CHANGED EXCEPT IN WRITING BY A DULY AUTHORIZED OFFICER

OF GLASSWERKS. GLASSWERKS SPECIFICALLY MAKES NO WARRANTY AS

TO THE SUITABILITY OF THE UNIT(S) FOR ANY PARTICULAR APPLICATION.

All warranty claims arising within the applicable period must be presented in writing as soon as possible to GLASSWERKS, accompanied where practicable by proof of purchase.

Upon verification, GLASSWERKS shall, at its option, either furnish the PURCHASER replacement glass shipped at GLASSWERKS’ expense or provide a refund of the original price to the PURCHASER. GLASSWERKS reserves the right to inspect any

LAMINATED GLASS product that is alleged to be defective prior to its removal from the glazing system, installation or fabrication location.

GLASSWERKS LA, INC.

Spec: 88000

1.5D, 2. A!

GL0"

FOR REFERENCE

ONLY. PREVIOUSLY

Guardian Industries – 14600 Romine Road – Carleton, Michigan 48117 – 734/654-4380

September 26, 2012

Reference: LEED 2009 for New Construction v3.0

Project Name:

Location:

Select

Fabricator:

Glazier:

Products:

To whom it may concern, Guardian’s popular SunGuard advanced architectural glass products are made at Kingsburg, CA, DeWitt, IA, Carleton, MI, Geneva, NY, and Corsicana, TX plants. These products can help projects earn

Leardership in Energy and Environmental Design (LEED) credits in up to five categories. Shown below is a brief summary of the potential LEED credits that are available for UTC when using Guardian glass for windows and façade applications.

Energy and Atmosphere Credit 1: Optimize Energy Performance (2-19 points)

Utilize SunGuard glass to increase energy performance above the prerequisite standard per ASHRAE or other applicable energy codes. Guardian float glass and SunGuard Advanced Architectural Glass products include the following products:

o SN 54, SN 62, SN 68, SNX 62/27on clear, green, UltraWhite

, CrystalGray , TwilightGreen o AG 50 and AG 43 on clear, green or CrystalGray float glass o RoyalBlue 40 on clear, green or CrystalGray float glass o Neutral 61, Neutral 50 and Neutral 40 on clear or green float glass o LightBlue 63 on clear or green float glass o Silver 20 and Silver 32 on clear or green float glass o NU 70 on clear float glass o Mirror, UltraMirror o Clear, green, UltraWhite, CrystalGray float glass

Material and Resources Credit 4: Recycled Content (1-2 points)

LEED v.3 does not allow in-plant recycled glass cullet to be counted as recycled content. Only recycled glass brought in from third-party manufacturing facilities will meet the definition of recycled content. The primary raw material for architectural glass is 72% silica sand. Trace amounts of other raw materials are present. Guardian float plants typically have 2% pre-consumer recycled content in their clear and green float glass and SunGuard glass products. UltraWhite and CrystalGray both have 0% pre-consumer recycled content. SatinDeco does not qualify as it is manufactured in Spain.

Material and Resources Credit 5: Regional Materials (1-2 points) The primary raw material for architectural glass is silica sand. Guardian’s source for silica sand is shown in the key on the following page. Guardian’s silica sand locations are within 500 miles of our float plants. To obtain this credit, building materials must be extracted, manufactured and fabricated within 500 miles of the project site.

Guardian’s independent Select

Fabricator Glass Dynamics in Stoneville, NC, is approximately 390 miles from UTC.

Material and Resources Credit 5:

Regional Materials cont.

LEED 2009 for New Construction v3.0

Spec:88000

1.5D, 2.2A

GL01

Clear, green, UltraWhite, CrystalGray float glass

Guardian’s popular SunGuard advanced architectural glass products are made at Kingsburg, CA, DeWitt, Guardian’s popular SunGuard advanced architectural glass products are made at Kingsburg, CA, DeWitt, Guardian’s popular SunGuard advanced architectural glass products are made at Kingsburg, CA, DeWitt, IA, Carleton, MI, Geneva, NY, and Corsicana, TX plants. These products can help projects earn

Guardian’s popular SunGuard advanced architectural glass products are made at Kingsburg, CA, DeWitt, Carleton, MI, Geneva, NY, and Corsicana, TX plants. These products can help projects earn

Leardership in Energy and Environmental Design (LEED) credits in up to five categories. Shown below Leardership in Energy and Environmental Design (LEED) credits in up to five categories.

whenis a brief summary of the potential LEED credits that are available for UTC when using Guardian glass is a brief summary of the potential LE for windows and façade applications.

FOR REFERENCE

ONLY. PREVIOUSLY

Guardian Industries – 14600 Romine Road – Carleton, Michigan 48117 – 734/654-4380

Indoor Environmental Quality Credits 8.1 and 8.2: Daylight and Views (1-2 points)

Utilize SunGuard glass to provide building occupants with a connection between indoor and outdoor spaces, through daylight penetration and external views from regularly occupied spaces in the building.

SunGuard products can provide up to 68% visible light transmission in a standard insulating glass unit, depending on the product.

Innovation and Design Process Credit 1: Innovation in Design (1-5 points)

SunGuard advanced architectural glass products can provide energy performance that substantially exceeds LEED-NC and energy code requirements which may help contribute to this credit.

Regional Priority Credit 1: Regional Priority (1-4 points)

Can be achieved through building strategies that address important environmental issues facing the region where the project is located. The potential contribution of glass products towards this bonus credit would be based priorities as established by local USGBC chapters and regional councils.

We appreciate your interest in Guardian SunGuard products. Please visit our website at http://na.en.sunguardglass.com/IntroToAdvancedArchitecturalGlass/GreenBuilding/index.htm for more information or contact me at 734-654-4380 or lrichard@guardian.com.

Best regards, Lin Richard

Marketing Specialist

Distance from Sand Source to

Manufacturing Facility

Carleton, MI 48117 – Oregon, IL 61061

370 mi.

Corsicana, TX 75109 - Cleverne, TX

76031 - 275 mi.

DeWitt, IA 52742 - Oregon, IL 61061 -

80 mi.

Floreffe, PA 15025 - Mapleton, PA

17052 - 155 mi.

Geneva, NY 14456 - Mapleton, PA

17052 - 234 mi.

Kingsburg, CA 93631 - Ione, CA 95640

- 177 mi

Richburg, SC 29729 - Marston, NC

28363 - 120 mi

Spec:88000

1.5D, 2.2A

GL01

FOR REFERENCE

ONLY. PREVIOUSLY

TM

888.653.3333www.safti.com S I N C E 1 9 8 1

PRODUCT ADVANTAGES

Fire Rating Application Max. CV Area Max. CV Width Max. CV Height StopsFire Rating Application Max. CV Area Max. CV Width Max. CV Height StopsFire Rating Application Max. CV Area Max. CV Width Max. CV Height StopsFire Rating Application Max. CV Area Max. CV Width Max. CV Height StopsFire Rating Application Max. CV Area Max. CV Width Max. CV Height StopsFire Rating Application Max. CV Area Max. CV Width Max. CV Height Stops

120 minutes Sidelites120 minutes Sidelites 4,876 sq. in. 124” 124”4,876 sq. in. 124” 124”4,876 sq. in. 124” 124” 5/8”

APPROVALS

SPECIFICATIONS

UL AND INTERTEK/WHI TESTED AND CERTIFIED

SuperLite II-XL is listed and labeled by Intertek/Warnock-

Hersey Inc. and Underwriters Laboratories, nationally recognized testing laboratories approved by OSHA.

FIRE RESISTIVE

Contains smoke, flames and blocks the passage of radiant heat.

UL 9, UL 10B, UL 10C, UL 263, NFPA 80, NFPA 251, NFPA 252, NFPA 257, ASTM E119, ASTM

E152, ASTM E163, ASTM E2074, ASTM E2010-01, CPSC 16 CFR 1201 Cat. II., ULC CAN4-S101, ULC

CAN4-S104, ULC CAN4-S106, NFRC 100, NFRC 200, NFRC 500.

STC 44

rating in 1-1/2” (39mm) standard profile

NFRC Certifications with GPX Framing:

0.34 U-Factor when insulated with

Solarban 60

0.27 SHGC when insulated with

Solarban 60

55 Condensation Resistance when insulated with Solarban 60

3-Part Specifications:

Available at www.safti.com/specifications

Maximum fire and impact safety with hose stream and full radiant heat protection.

Largest tested and approved sizes up to 4,876 sq.in. in standard 1-1/2” profile.

Tint-free and optically clear. Perfect for property line requirements.

Acoustical value of 44 STC.

Available in custom architectural make-ups, such as laminated glass and energy-saving insulated units with NFRC certifications when used with GPX framing.

USA manufactured for fast delivery and competitive pricing.

120 minute

Fire Resistive Glazing

GREENFIRE RATED GREEN HOSE STREAM RADIANT HEAT IMPACT RATED THERMAL SHOCK POSITIVE PRESSURE

Made in the USA

1” stops recommended!!!!

5 year warranty.

Largest tested and approved sizes up to 4,876 sq.in. in standard 1-1/2” profile.

Spec: 88000

1.5D, 2.9A

GL03

120 minute

Fire Resistive Glazing

120 minutes Sidelites120 minutes Sidelites

Windows

Transoms

Walls

USA manufactured for fast delivery and competitive pricing.

Thickness: 1-1/2” (39mm) standard thickness

Weight: 12 lbs./sq. ft. in 1-1/2” (39 mm) standard profile

Sound Transmission Rating: STC 44 rating in 1-1/2” (39mm) standard profile

Fire Rating: 12120 0 minutes wiwithth hose ststreamam Fire Rating:

MeMeetets s ASASTMTM E E11119 9 anand d NFNFPAPA 2 25151

Impact Safety Rating:

CPSC 16 CFR 1201 Cat. I and II

FOR REFERENCE

ONLY. PREVIOUSLY

TM

888.653.3333www.safti.com S I N C E 1 9 8 1

TYPICAL DETAILS More details available at www.safti.com/details

120 120 minute

Fire Resistive Glazing

Project: Reece School in New York, NY

Architect: Platt Byard Dovell White Architects LLP

Glazier: Industrial Window Corporation

The information provided herein is for general reference only. Please visit www.safti.com for the most updated information.

Scale 3” = 1”

Project: CA Endowment Building in Los Angeles, CA

Architect: House and Robertson Architects

Glazier: Benson Industries, Inc.

Here are two more examples of how

GPX framing with SuperLite II-XL glazing enhances interior spaces with elegant transparency during normal use while protecting building occupants from the danger of radiant heat and providing safe egress during a fire.

FIRE RESISTIVE

FIRE RESISTIVE

FIRE RESISTIVE

FIRE RESISTIVE

SuperLite II-XL 120 in GPX Framing and

SuperLite II-XL 90 in GPX Door

TYPICAL DETAILS

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

Welcome to the SAFTIFIRSTTM Guide Specification System prepared as an aid to specifiers in preparing written construction documents. For specification assistance with specific product applications, please contact SAFTIFIRSTTM. To download an electronic copy, please visit www.safti.com.

SPECIFICATION

SECTION 08 8810: FIRE RATED GLASS & FRAMING

SuperLiteTM II-XL 120 minute and SuperLiteTM II-XL 120 minute with Starphire® Ultra-Clear Glass by PPG

PART 1 GENERAL

1.01 SUMMARY

A. Section Includes: Fire rated glazing

1. SuperLiteTM II-XL 120 fire resistive, safety rated glazing material for interior and exterior applications.

2. Applications of fire rated glazing includes:

a. Fire rated glazing as sidelites, borrowed lites, windows, transoms and transparent wall applications in fire rated frames.

B. Related sections:

1. Section 01 3323: Shop Drawings, Product Data and Samples.

2. Section 08 8000: Glazing.

3. Section 08 5130: Steel Window.

4. Section 08 1110: Steel Doors and Frames.

5. Section 08 1400: Wood Doors and Frames.

6. Section 08 1120: Aluminum Doors and Frames.

7. Section 08 5110: Aluminum Windows.

8. Section 08 1113: Hollow Metal Doors and Frames.

9. Section 08 7000: Finish Hardware.

1.02 REFERENCES

A. American Society for Testing and Materials (ASTM):

1. ASTM E119: Methods for Fire Tests of Building Construction and Materials.

2. ASTM E152: Methods for Fire Tests of Door Assemblies.

3. ASTM E163: Methods for Fire Tests of Window Assemblies.

4. ASTM E2074: Standard Test Method for Fire Tests of Door Assemblies, including

Positive Pressure Testing of Side-hinged and Pivoted Swinging Door Assemblies.

5. ASTM E2010-1: Standard Test for Positive Pressure of Fire Tests of Window

Assemblies.

B. National fire Protection Association (NFPA):

1. NFPA 80: Fire Doors and Windows.

2. NFPA 251: Fire Tests of Building Construction and Materials.

3. NFPA 252: Fire Tests of Door Assemblies.

4. NFPA 257: Fire Tests of Window Assemblies.

C. Underwrites Laboratories, Inc. (UL):

1. UL 9: Standard for Safety of Fire Tests of Window Assemblies.

SuperLiteTM II-X-XL 120 minute a

A. Section Includes: Fire rated glazing

1. SuperLiteTM II-XL 120 fire resistive, safety rated glazing material for interior and exterior1. SuperLite applications.

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

2. UL 10 B: Standard for Safety of Fire Tests of Door Assemblies.

3. UL 10 C: Standard for Safety of Positive Pressure Tests of Door Assemblies.

4. UL 263: Fire Tests of Building Construction and Materials.

D. Standard Council of Canada:

1. ULC Standard CAN4-S101: Fire Tests of Building Construction and Materials.

2. ULC Standard CAN4-S104: Fire Tests of Door Assemblies.

3. ULC Standard CAN4-S106: Fire Tests of Window Assemblies.

E. Consumer Product Safety Commission (CPSC):

1. CPSC 16 CFR 1201: Safety Standard for Architectural Glazing Materials.

F. Glass Association of North America (GANA)

1. GANA – Glazing Manual.

2. FGMA – Sealant Manual.

G. [American Recovery and Reinvestment Act

1. Section 1605, Title XVI Buy American Provision]

H. [Insert building code used by Authority Having Jurisdiction]

1.03 SYSTEM DESCRIPTION

A. Performance Requirements: Provide a fire rated glazing manufactured, fabricated and installed to maintain performance criteria stated by manufacturer without defects, damage, or failure.

1. Fire Rating: 120 minutes with hose stream.

2. Fire resistive, safety rated glazing tested in accordance with ASTM E119, NFPA 80, NFPA 251, NFPA 252, NFPA 257, UL 9, UL 10B, UL 10C and UL 263.

3. Testing Laboratory: Fire tests shall be conducted by a nationally recognized independent testing laboratory.

B. Listings and Labels:

1. Fire rated glazing shall be under current follow-up services by a nationally recognized independent testing laboratory approved by OSHA and maintain a current listing or certification. Assemblies shall be labeled in accordance with limits of listings.

1.04 SUBMITTALS

A. Submit listed submittals in accordance with Conditions of the Contract and Division 1 Submittal Procedure Section.

1. Shop Drawings: Submit shop drawings showing layouts, profiles and product components.

2. Samples: Submit 12x12 glass samples.

3. Technical Information: Submit latest edition of manufacturer’s product data.

1.05 DELIVERY, STORAGE AND HANDLING

A. General: Comply with Division 1 Product Requirements Sections.

1. Fire Rating: 120 minutes with hose stream.

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

B. Ordering: Comply with manufacturer’s ordering instructions and lead-time requirements to avoid construction delays.

C. Delivery: Deliver materials to specified destinations in manufacturer or distributor’s packaging.

D. Storage and Protection: Store off ground, under cover, protected from weather and construction activities and at temperature conditions recommended by manufacturer.

1.06 PROJECT CONDITIONS

A. Field Measurements: Verify actual measurements for openings by field measurements before fabrication. Show recorded measurements on shop drawings. Coordinate field measurements and fabrication schedule with construction progress to avoid construction delays.

1.07 WARRANTY

A. Project Warranty: Refer to Conditions of the Contract for project warranty provisions.

B. Manufacturer’s Warranty: Submit, for Owner’s acceptance, manufacturer’s standard warranty document. Manufacturer’s warranty is not intended to limit other rights that the Owner may have under the Contract Documents.

1. Warranty Period: 5 years from date of shipping.

PART 2 PRODUCTS

2.01 FIRE RATED GLAZING

A. Material: SuperLiteTM II-XL 120 minute fire resistive glazing with hose stream.

B. Manufacturer: SuperLiteTM II-XL as manufactured and distributed by SAFTI FIRST.

1. Contact: 100 N Hill Drive, Suite 12, Brisbane, CA 94005; Telephone 888.653.3333;

Fax 888.653.4444; email info@safti.com; Web site www.safti.com

2. Fire rated glass and framing must be provided by a single-source, US manufacturer.

Distributors of fire rated glass and framing are not to be considered as manufacturers.

C. Design Requirements:

1. Make-up: Must be comprised of an inboard and outboard lite of [clear tempered glass]

[Starphire® Ultra-Clear Low-Iron Tempered Glass by PPG] protecting a clear, fire resistive, intumescent interlayer.

2. Thickness: 1-1/2” (39 mm) standard profile. 1-1/4” thin profile available.

3. Weight: 12 lbs/sq. ft. in 1-1/2” (39 mm) standard profile.

4. Dimensions: Must meet max. clear view area of 4,876 sq. in., measuring at least 124

in. on the long side.

5. Visible Light Transmission: Must meet [0.81 with clear tempered] [0.89 with Starphire]

6. Solar Heat Gain Coefficient: Must meet 0.27 when used with SuperLite II-XL Starphire insulated with Solarban 70XL.

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

7. U-Factor: Must meet [0.80 standard] [0.41 when used with SuperLite II-XL clear tempered insulated with Solarban 70XL] [0.25 when used with SuperLite II-XL with Starphire insulated with Solarban 70XL].

8. NFRC Certifications in conjunction with GPX or CW Framing by SAFTI FIRST. Must be used as an assembly.

8.1. Must meet NFRC 100 rated U-Factor of 0.34 when insulated with Solarban 60.

8.2. Must meet NFRC 200 rated SHGC of 0.27 when insulated with Solarban 60.

8.3. Must meet NFRC 500 rated Condensation Resistance of 55 when insulated with Solarban 60.

9. Sound Transmission Rating: Must provide a minimum of STC 44 Rating in 1-1/2” (39

mm) standard profile.

10. Appearance: Must be tint-free, optically clear fire rated glazing.

11. Fire Rating: Must be fire rated to 120 minutes with hose stream and meet ASTM E-119.

12. Impact Safety Resistance: CPSC 16 CFR 1201 Cat. I & II.

13. Customization: Available in insulated, energy performance, bullet-resistant, blast-resistant, hurricane-resistant, laminated, tinted, patterned, frosted, mirrored, reflective, segmented, decorative and more.

D. Manufacturer’s Fire Rating Glazing Material:

1. Each piece of fire-rated glazing material shall be labeled with a permanent logo including name of product, manufacturer, testing laboratory, fire rating period and safety glazing standards.

2. Glazing materials installed in Hazardous Locations, subject to human impact, shall be certified and permanently labeled as meeting applicable requirements reference in

NFPA 80:

a. CPSC 16 CFR 1201 Cat. I & II

E. Substitutions: No substitutions allowed.

2.02 MATERIALS

A. Glazing Accessories: Manufacturer recommended fire rated glazing accessory as follows:

1. Glazing with EPDM tape or other listed flame resistant gasket material and calcium silicate setting blocks.

2.03 RELATED PRODUCTS

Note: Basis of design for fire rated framing system is SAFTIfire TM Framing as manufactured by SAFTI FIRSTTM

A. Glazing shall be installed in an equally rated framing system.

2.04 SOURCE QUALITY

A. Obtain fire rated glazing products from a single manufacturer.

B. Fabrication Dimensions: Fabricate to approved dimensions. The general contractor shall guarantee dimensions where practicable within required tolerances.

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

PART 3 EXECUTION

3.01 MANUFACTURER’S INSTRUCTIONS

A. Compliance: Comply with manufacturer’s product data including product technical bulletins and installation instructions.

3.02 EXAMINATION

A. Site Verification of Conditions: Verify substrate conditions, have been previously installed under other sections, and are acceptable for product installation in accordance with manufacturer’s instructions.

3.03 INSTALLATION

A. Installation shall be in strict accordance with the fire glazing material manufacturer’s specifications. Field cutting or tampering is strictly prohibited.

3.04 CLEANING AND PROTECTION

A. Protect glass from contact with contaminating substances resulting from construction operations. Remove such substances by method approved by manufacturer.

B. Wash glass on both faces not more than four days prior to date schedule for inspections intended to establish date of Substantial Completion. Wash glass by method recommended by glass manufacturer.

C. Remove temporary coverings and protection of adjacent work areas.

D. Remove construction debris from project site and legally dispose of debris.

END OF SECTION

In the interest of continuous improvement of its product line, SAFTIFIRSTTM reserves the right to modify its products’ composition, colors, textures, sizes, and other physical and performance attributes and these guide specifications at any time. SAFTIFIRSTTM makes no expressed or implied warranties regarding content, errors, or omissions in the information presented. Specifications modified or rewritten not in conformance with manufacturer’s standard processes, products, and procedures may void warranties and related remedies.

Spec: 88000

1.5D, 2.9A

GL03

FOR REFERENCE

ONLY. PREVIOUSLY

01$/&'(')*&'+/ +( &2$ -%+13)& )+4$%$1 56 &2'7

)$%&'(')*&$8

#3-$%9'&$ 00:;9

!'&*&'+/ &+ $*)2 !"#! -%+13)& 7*($&6

%$<3.*&'+/ &+ =2')2 &2'7 -%+13)& '7 5$'/<

)$%&'('$18

!"#! >? !@A >BC> !*&$<+%6 0 */1 00

01$/&'(')*&'+/ +( &2$ D# ',-+%&$% +% 1+,$7&')

,*/3(*)&3%$% )$%&'(6'/< )+,-.'*/)$ +( &2$

-%+13)&8

#E@F0 FIRST @'%$ A*&$1 G.*H'/< #+.3&'+/7I *

1'4'7'+/ +( JKL$$(($K7 0/)M

!+/&*)& '/(+%,*&'+/ (+% &2$ '/1'4'13*.

,*'/&*'/'/< %$)+%17 +( &$7& %$73.&78

L$..6 JKL$$(($

N')$ "%$7'1$/&

"8 OOOM?PQMQQQQ

@8 R>PMOBRMPSCC

QBP T$=2*.. #&%$$&I #*/ @%*/)'7)+I !E SR>BR

U*&$ */1 -.*)$ =2$%$ &2'7 -%+13)& =*7

,*/3(*)&3%$18

U*&$8 VVVVVVVVVVVVVVVVVV

".*)$8 BBC #+3&2 A #&%$$&I W$%)$1I !E SPQR>

U*&$ */1 -.*)$ =2$%$ &2'7 -%+13)& =*7 &$7&$1

(+% )+,-.'*/)$ ='&2 &2$ %$<3.*&'+/X7Y )'&$1

*5+4$8

U*&$8 >BZ>>ZBCCC

".*)$8 BBCC [6,+%$ [*6I E/&'+)2 0/137&%'*.

"*%\I E/&'+)2I !E SRPCS

01$/&'(')*&'+/ +( */6 &2'%1:-*%&6 .*5+%*&+%6 +/

=2+7$ &$7&'/< &2$ )$%&'(')*&$ 1$-$/178

0/&$%&$\Z[*%/+)\:]$%7$6 0/)M

Spec: 88000

1.5D, 2.9A

GL03

Please insert your invoice date

FOR REFERENCE

ONLY. PREVIOUSLY

LIMITED WARRANTY

FURNISHED TO: SAMPLE PROJECT: SAMPLE

SALES ORDER: SAMPLE

SAFTI FIRST warrants that their products shall be free from defective material and comply with SAFTI FIRST’s published Quality Specifications and Inspection Standards for a period of five (5) years from the date of delivery provided that said products have been installed and maintained in accordance with SAFTI FIRST’s installation instructions and published maintenance recommendations. This warranty is limited to defects appearing in the door, window or wall framing and glazing components. This warranty is limited to the glass and framing manufacturing only and does not cover “hardware supplied by others”. Should there be a defect found in operating di!culty with any hardware component, Owner should contact the respective manufacturer or consult the warranty agreement that covers the hardware component in question.

This warranty is limited to the repair or replacement of defective material or entire product and shall be determined at the discretion of the manufacturer as to what action to take.

SAFTI FIRST extends the SuperSecure II-XLS manufacturer’s warranty to the immediate buyer. The conditions of this warranty for the SuperSecure II-XLS glazing material are as follows:

The supplier warrants its immediate buyers for a period of five (5) years from the date of delivery that under normal conditions, the free vision through the SuperSecure II-XLS glass will not be adversely affected.

The use of tempered glass as well as the clear fire resistive intumescent interlayer can lead to certain optical irregularities, especially near the glass edges. These inherent irregularities do not affect the free vision through the glass. Normal conditions imply in particular that the clear fire resistive intumescent interlayer is not allowed to reach temperatures below 32 degrees Fahrenheit or over 110 degrees Fahrenheit (0 – 43 degrees

Celsius).

The warranty is subject to the following provisions:

" A liability under this warranty is limited to free repair or replacement (at the manufacturer’s discretion) of defective glass and/or frames and shall not extend to any other damages in connection with defective glass. Installation of the replacement glass into GPX framing is not covered under this warranty.

" The warranty shall not apply to units which have not been handled in accordance with normal conditions of use, or units which have been subsequently processed or modified in any way, or units which have been subject to any damage affecting the bond of the

SuperSecure II-XLS units. Normal conditions of use include but are not limited to temperatures between 32 degrees Fahrenheit and

110 degrees Fahrenheit.

" Manufacturer’s warranties on component parts of materials may di"er from the terms specified herein and will supersede SAFTI

FIRST’s standard warranty.

" The manufacturer’s liability will also not apply in cases where defects are not reported within 30 days after they have become recognizable by the initial buyer or by the users of the building into which SuperSecure II-XLS has been installed. Liability will therefore expire at the latest 30 days after the expiration of the warranty, also if the defect has not been recognizable before expiration of the 5-year warranty period. Any glass replaced or repaired under this warranty is limited by the original warranty period and shall not be extended beyond the original five years.

" Furthermore, the conditions for quality complaints according to the manufacturer’s general conditions of sale for export shall apply.

" If SuperSecure II-XLS is exported to a country other than where the initial delivery has been made, the warranty will only be valid if the manufacturer has accepted this exportation.

" Building and safety codes vary widely throughout the world. SAFTI FIRST does not control nor will it be responsible for the selection of product supplied by others, configurations, or the glazing materials used in the manufacture of its door, window or wall systems. SAFTI FIRST makes no other warranties or representation, either expressed or implied, concerning product fitness for a particular purpose. SAFTI FIRST will fabricate to dimensions shown on approved drawings but will not take responsibility for failure of submitting party(s) shop drawing dimensions against job site conditions. In no event will SAFTI FIRST be liable for direct, indirect, special or consequential damages including but not limited to loss of profit or use.

" SAFTI FIRST reserves the right to inspect or have returned all products alleged to be defective excluding shipping and handling costs.

" SAFTI FIRST makes no other warranty, expressed or implied, regarding its products.

SAMPLE SAMPLE

Katarzyna Grzelak, Sales Administrator Date

Spec: 88000

1.5D, 2.9A

GL03

LIMITED WARRANTY

The supplier warrants its immediate buyers for a period of five (5) years from the date of delivery that under normal conditions, the free vision supp ye for a pe ve (5) y through th he SuperSecure II-XLS glass will not be adves will not be ads will not be ad rsely affected. ffff

FOR REFERENCE

ONLY. PREVIOUSLY

Materials & Resources

Reduce, reuse, recycle. Three essential steps in conservation of resources. These elements, in addition to consideration of local/regional sourcing of materials, are a few of the important ways to reduce impacts.

How SAFTIFIRST products can help:

Credits 2.1 and 2.2 – Construction Waste Management

SAFTIFIRST products are supplied to the construction site in the exact quantities needed, however should products be damaged in transit, both the glass and the metal framing systems can be recycled. Products are either delivered on wooden pallets or in shipping boxes – both of which are made from recycled materials and can be recycled after use.

Credits 4.1 and 4.2 – Recycled Content

Steel used in the GPX framing system contains approximately 30% by weight pre-consumer recycled content.

Aluminum used in the GPX framing system contains approximately 25% by weight pre-consumer recycled content.

Credits 5.1 and 5.2 – Regional Materials

All products manufactured by SAFTIFIRST are made in our plant in Merced, CA. The primary raw material used in

SAFTIFIRST glass products, sand, is sourced from less than 70 miles from the plant. All projects in California and those located in some cities in Nevada and Arizona may qualify for this credit if they are within 500 miles of the Merced facility.

Energy & Atmosphere

Reducing energy is an essential aspect of any sustainable building design. Utilizing energy efficient products and taking advantage of daylighting helps to achieve significant energy savings.

How SAFTIFIRST products can help:

Prerequisite 2 – Minimum Energy Performance

SAFTIFIRST products can be part of a strategy to help achieve the required minimum energy performance for LEED® certification.

Credit 1 – Optimize Energy Performance

Our glass products have the option of being insulated with low-e or energy performance glazing to further improve the energy performance of the building. Our SuperLite II-XL and GPX Framing assemblies have NFRC (National Fenestration

Ratings Council) certifications for U-Factor, Solar Heat Gain Coefficient and Condensation Resistance. In addition, our glass products can be used as part of daylighting strategies and passive solar designs to further reduce the amount of energy consumed by the building. Using fire rated glass maximizes light penetration, even from artificial lighting, by providing light transmittance in areas where opaque walls are the norm.

The LEED® (Leadership in Energy & Environmental Design) Green Building Rating

System is the nationally accepted benchmark for the design and construction of high performance green buildings. While the use of no single construction material can earn LEED® points, SAFTIFIRST’s fire rated glass and framing products can contribute to a number of LEED® 2009 credits including:

LEED

Brochure and Scorecard

University of Utah

David Eccles School of Business

Salt Lake City, UT

Spec: 88000

1.5D, 2.9A, GL03

LEEDLEED

Brochure and Scorecard Brochure and Scorecard

FOR REFERENCE

ONLY. PREVIOUSLY

To learn more about SAFTIFIRST’s fire rated glass and framing products, please visit www.safti.com or call 888.653.3333

Beyond LEED®

While LEED® is an important measure of green building, sustainable building design goes beyond LEED®.

Sustainable buildings are high performance buildings that incorporate features that provide resiliency and durability, as well as minimize their environmental footprint. This includes not only responsiveness to climate change, but also to fire, hurricanes and floods.

SAFTIFIRST products can contribute to the following features of a high-performance, resilient building:

Safety and Security

Resilience is a sometimes overlooked aspect of sustainable buildings, but one that is essential to long-term performance. Resilient buildings withstand what nature dishes out. They include fire resistant construction and resistance to wind-borne debris and other impacts – all of which promote occupant health and safety. All SAFTI-

FIRST glass, framing and PYRAN Platinum products protect against fire. SuperLite II-XL can be manufactured to provide resistance to impacts, including ballistic, hurricane and blast.

Another aspect of safety and security involves vision and lines of sight. SAFTIFIRST glass products can provide visual access while still providing security. This is especially true for stairwells and other areas where attack is prone to occur because of the lack of visual access.

Environmentally Preferable Materials and Products

SAFTIFIRST glass products are made primarily from sand, an abundant material, and do not contain toxic materials.

This includes the PYRAN Platinum line of products, which are the only glass ceramics currently available that are free from toxins and hazardous heavy metals during the manufacturing process. This superior environmental performance has been recognized in the C2C (Cradle to Cradle) certification of PYRAN Platinum.

Innovation and Design

Cradle to Cradle (C2C) Certification

The Cradle to Cradle (C2C) certification for products is a recognized innovation credit when at least 2.5% (by cost) of the materials on a project achieve C2C certification. PYRAN Platinum by SAFTIFIRST is currently the only glass ceramic on the market that meets these requirements.

Acoustic Performance

Acoustic design is another potential area for Innovation in LEED-NC and is part of the LEED® for Schools rating system (IEQ credit 9). The criteria in LEED® for Schools requires that windows in the building shell, classroom partitions and other core learning space partitions meet an STC rating of at least 35. All SuperLite II-XL, SuperLite X-90 and PYRAN Platinum L products meet these STC requirements.

Indoor Environmental Quality

Creating a healthy indoor environment is important for our wellbeing.

How SAFTI FIRST products can help:

All SAFTIFIRST glass products can be used to provide daylighting and visual access. In addition, SuperLite II-XL can be used as a fire resistive transparent wall to provide clear, transparent glazing that blocks radiant heat transfer.

Credit 4 – Low-Emitting Materials

SAFTIFIRST glass products meet the intent of eliminating VOC’s from the indoor environment when used as interior walls and glazing.

Credit 8 – Daylight and Views

SAFTIFIRST glass products can be an integral part of a strategy to provide both daylight and views while still providing sound control, security, and privacy. SuperLite II-XL transparent walls can be used in lieu of traditional opaque fire walls to allow natural light penetration and preserve views deep within a building.

Spec: 88000

1.5D, 2.9A, GL03

FOR REFERENCE

ONLY. PREVIOUSLY

LEED® 2009 for New Construction and Major Renovation

Project Scorecard

Yes ? No

Y Prereq 1 Construction Activity Pollution Prevention Required

Credit 1 Site Selection 1

Credit 2 Development Density and Community Connectivity 5

Credit 3 Brownfield Redevelopment 1

Credit 4.1 Alternative Transportation - Public Transportation Access 6

Credit 4.2 Alternative Transportation - Bicycle Storage and Changing Rooms 1

Credit 4.3 Alternative Transportation - Low-Emitting and Fuel-Efficient Vehicles 3

Credit 4.4 Alternative Transportation - Parking Capacity 2

Credit 5.1 Site Development - Protect or Restore Habitat 1

Credit 5.2 Site Development - Maximize Open Space 1

Credit 6.1 Stormwater Design - Quantity Control 1

Credit 6.2 Stormwater Design - Quality Control 1

Credit 7.1 Heat Island Effect - Nonroof 1

Credit 7.2 Heat Island Effect - Roof 1

Credit 8 Light Pollution Reduction 1

Yes ? No

Y Prereq 1 Water Use Reduction Required

Credit 1 Water Efficient Landscaping 2 to 4

Reduce by 50% 2

No Potable Water Use or Irrigation 4

Credit 2 Innovative Wastewater Technologies 2

Credit 3 Water Use Reduction 2 to 4

Reduce by 30% 2

Reduce by 35% 3

Reduce by 40% 4

Yes ? No

Y Prereq 1 Fundamental Commissioning of Building Energy Systems Required

Y Prereq 2 Minimum Energy Performance Required

Y Prereq 3 Fundamental Refrigerant Management Required

Credit 1 Optimize Energy Performance 1 to 19

Improve by 12% for New Buildings or 8% for Existing Building Renovations 1

Improve by 14% for New Buildings or 10% for Existing Building Renovations 2

Improve by 16% for New Buildings or 12% for Existing Building Renovations 3

Improve by 18% for New Buildings or 14% for Existing Building Renovations 4

Improve by 20% for New Buildings or 16% for Existing Building Renovations 5

Improve by 22% for New Buildings or 18% for Existing Building Renovations 6

Improve by 24% for New Buildings or 20% for Existing Building Renovations 7

Improve by 26% for New Buildings or 22% for Existing Building Renovations 8

Improve by 28% for New Buildings or 24% for Existing Building Renovations 9

Improve by 30% for New Buildings or 26% for Existing Building Renovations 10

Improve by 32% for New Buildings or 28% for Existing Building Renovations 11

Improve by 34% for New Buildings or 30% for Existing Building Renovations 12

Improve by 36% for New Buildings or 32% for Existing Building Renovations 13

Improve by 38% for New Buildings or 34% for Existing Building Renovations 14

Improve by 40% for New Buildings or 36% for Existing Building Renovations 15

Improve by 42% for New Buildings or 38% for Existing Building Renovations 16

Improve by 44% for New Buildings or 40% for Existing Building Renovations 17

Improve by 46% for New Buildings or 42% for Existing Building Renovations 18

Improve by 48%+ for New Buildings or 44%+ for Existing Building Renovations 19

Credit 2 On-Site Renewable Energy 1 to 7

1% Renewable Energy 1

3% Renewable Energy 2

5% Renewable Energy 3

7% Renewable Energy 4

9% Renewable Energy 5

11% Renewable Energy 6

13% Renewable Energy 7

Credit 3 Enhanced Commissioning 2

Credit 4 Enhanced Refrigerant Management 2

Credit 5 Measurement and Verification 3

Credit 6 Green Power 2

Fire Rated Glass & Framing can contribute to the credits highlighted below.

TM

Energy & Atmosphere 35 Points

Water Efficiency 10 Points

Sustainable Sites 26 Points

Spec: 88000

1.5D, 2.9A, GL03

FOR REFERENCE

ONLY. PREVIOUSLY

This brochure is printed on recycled paper.

'LEED®' and related logo is a trademark owned by the

U.S. Green Building Council® and is used with permission.

Yes ? No

Y Prereq 1 Storage and Collection of Recyclables Required

Credit 1.1 Building Reuse - Maintain Existing Walls, Floors and Roof 1 to 3

Reuse 55% 1

Reuse 75% 2

Reuse 95% 3

Credit 1.2 Building Reuse - Maintain Interior Nonstructural Elements 1

Credit 2 Construction Waste Management 1 to 2

50% Recycled or Salvaged 1

75% Recycled or Salvaged 2

Credit 3 Materials Reuse 1 to 2

Reuse 5% 1

Reuse 10% 2

Credit 4 Recycled Content * 1 to 2

10% of Content 1

20% of Content 2

Credit 5 Regional Materials 1 to 2

10% of Materials 1

20% of Materials 2

Credit 6 Rapidly Renewable Materials 1

Credit 7 Certified Wood 1

* SAFTIFIRST GPX metal framing systems

Yes ? No

Y Prereq 1 Minimum Indoor Air Quality Performance Required

Y Prereq 2 Environmental Tobacco Smoke (ETS) Control Required

Credit 1 Outdoor Air Delivery Monitoring 1

Credit 2 Increased Ventilation 1

Credit 3.1 Construction Indoor Air Quality Management Plan - During Construction 1

Credit 3.2 Construction Indoor Air Quality Management Plan - Before Occupancy 1

Credit 4.1 Low-Emitting Materials - Adhesives and Sealants 1

Credit 4.2 Low-Emitting Materials - Paints and Coatings 1

Credit 4.3 Low-Emitting Materials - Flooring Systems 1

Credit 4.4 Low-Emitting Materials - Composite Wood and Agrifiber Products 1

Credit 5 Indoor Chemical and Pollutant Source Control 1

Credit 6.1 Controllability of Systems - Lighting 1

Credit 6.2 Controllability of Systems - Thermal Comfort 1

Credit 7.1 Thermal Comfort - Design 1

Credit 7.2 Thermal Comfort - Verification 1

Credit 8.1 Daylight and Views - Daylight 1

Credit 8.2 Daylight and Views - Views 1

Yes ? No

Credit 1 Innovation in Design 1 to 5

Innovation or Exemplary Performance 1

Innovation or Exemplary Performance 1

Innovation or Exemplary Performance 1

Innovation - Cradle to Cradle (C2C) Certification 1

Innovation - Acoustic Performance 1

Credit 2 LEED® Accredited Professional 1

Yes ? No

Credit 1 Regional Priority 1 to 4

Regionally Defined Credit Achieved 1

Regionally Defined Credit Achieved 1

Regionally Defined Credit Achieved 1

Regionally Defined Credit Achieved 1

Yes ? No

Certified: 40-49 points Silver: 50-59 points Gold: 60-69 points Platinum: 80+ points

Fire Rated Glass & Framing can contribute to the credits highlighted below.

TM

PROJECT TOTALS (Certification Estimates)

Regional Priority 4 Points

Innovation in Design 6 Points

Indoor Environmental Quality 15 Points

Materials & Resources 14 Points

Spec: 88000

1.5D, 2.9A, GL03

FOR REFERENCE

ONLY. PREVIOUSLY

1.5D, 2.1B

GL04, GL05, GL08

Submit textured glass surface sealer as specified in 08 80 00 2.1 B 1

FOR REFERENCE

ONLY. PREVIOUSLY

SunGuard® is a registered trademark of Guardian Industries Corp. Page 1 of 2

PERFORMANCE

CALCULATOR

April 16, 2014 Prepared for Mountain Valley Glass

By Heckard, Rhonda rhondah@glasswerks.com

7/16" 65% White Lami Tempered

Make-up Name

Make-up

Outboard Substrate &

Coating

Transmission Reflectance U-Value

RHG

(Btu/ hr-ft²)

SC SHGC LSG CRI OITC

Visible Light %

UV %

Solar

Energy

Visible Out %

Visible In

Solar Energy Out %

Winter Night

(Btu/hr-ft²-F)

Summer Day

(Btu/hr-ft²-F)

7/16" 65% White Lami Tempered

Clear 47 0 39 18 19 14 0.96 0.88 136 0.62 0.53 0.88 98 N/A

Calculation Standard: NFRC 2010

7/16" 65% White Lami Tempered

Thermal Stress

Guideline

(°F)

Go…