J04 Building 51428 asbestos reports DRAFT.pdf

Client Job: 1-8649693 PO Number: 51428

JobNumber: 201910185

Routing Number: -

# Samples: 12

PLMn

PLM The "New" Method; see below

Client:

Polarized Light Microscope (PLM) Analysis for Asbestos in Bulk Sample

Method and Analysis Information:

Each bulk sample is first dissected under a 7-30x magnification stereo-microscope. This examination is used to determine the general type of sample, how many and what type of layers it has, and initial estimates of fiber types and quantities. Second, liquid media mounts are made of each layer -such mounts may be of selected fibers (used solely for identification purposes) or may be representative of the layer as a whole (used for quantitation purposes). The mounts may be made in a synthetic Canadian balsam, one of several solvents, or in refractive index oils (media of known refractive index). Generally, a variety of different mounts are made: some optimized for fiber visibility, some optimized for fiber identification, and some optimized for fiber quantitation. The mounted slides are then examined at 50-400x magnification on a Nikon Labphot-pol microscope. Optical characteristics are used to identify each observed fiber type; the optical data are contained for each sample on its detail analysis sheet, attached.

Current EPA and NESHAP regulations designate a result of ≤1 % asbestos as "negative" or "non-regulated"and >1 % asbestos as "positive" or

"regulated." Samples containing layers that have been determined to be "positive" may have to be handled differently during a renovation or demolition than samples whose layers have been determined to be "negative." OSHA under CFR 1926.1101 regulates work done involving any detectable concentration of asbestos.

The method of fiber identification and quantitation is the “Standard Operating Procedures for the Analysis of Asbestos in Bulk Samples using Polarized

Light Microscopy”, Chapter 7 of the Quality Assurance and Management Manual. This SOP and its associated reporting have been designed to satisfy all requirements in both EPA Method 600/M4-82-020 (The Interim Method) and EPA Method 600/R-93/116 (The New Method). The Interim Method is the required method for AHERA (US EPA 40 CFR Pt. 763), but this method calls for the reporting of composited results of multi-layered samples that is no longer an acceptable reporting practice in most circumstances. Current EPA rules, such as NESHAP (US EPA 40 CFR Pt. 61), as well as NVLAP accreditation policies, call for separate reporting for each layer of multi-layered samples. The New Method contains the same procedures for identification and quantification of asbestos as does the Interim Method, except that multi-layered samples are reported to comply with the latest US EPA rule. Fiberquant not only reports the asbestos content of each layer of multi-layered samples separately (satisfying current EPA and NVLAP reporting requirements), but Fiberquant also reports what percentage of the sample each layer comprises. Therefore, the results may be arithmetically composited to satisfy the reporting requirements of the Interim Method. The method of fiber quantitation is an estimation technique in which the analysts quantitation is routinely calibrated by reference quantitation standards, and which has been shown to be equivalent in precision and accuracy to point counting. Friability is estimated for the purposes of deciding when to point count. Friabilities determined in the field take precedence over those determined in the laboratory. Those sample layers which are friable and estimated by the analyst to contain <= 1% asbestos are point counted using 400 points. Such point counting is required by NESHAP (National Emission Standards for Hazardous Air Polutants, Nov. 1990) in order to rely on analytical results that are ≤ 1%. The coefficient of variation for the estimation quantitation technique is 100% in the range 0-5%.

This means that PLM analysis is not capable of conclusively determining whether a layer containing close to 1% asbestos is actually "positive" or "negative". For this reason, Fiberquant refers to results where asbestos was detected but ≤ 1% as "borderline negative", and results where asbestos was >1 % but <= 2% as "borderline positive" to indicate the uncertainty in assigning a "positive" or "negative" label. In the sample summary, "ND" means that no asbestos was detected during the analysis. A "Tr" or "Trace" of asbestos reported is defined for our purposes as the detection of several asbestos fibers during the analysis; this level would be right at the limit of detection for the method. Trace is only reported on the analysis detail - in the summary a trace would be reported as <=1%. The limit of detection (the smallest % of asbestos that can be detected) varies greatly depending on the matrix in which the asbestos is found. As little as 0.001% asbestos can be detected in favorable samples, while detection in unfavorable samples may approach the detection limit of 1% stated in the method. During the analysis, the analyst, for Fiberquant identification purposes only, determines the "apparent sample type" and "apparent layer types." It must be emphasized that these types are only what is apparent. Often, different materials appear similar or identical after sampling, so the analyst may assign a type other than what was sampled.

Floor tiles present a special problem for PLM asbestos analysis. Floor tile can contain chrysotile fibers so thin that they cannot be resolved by optical methods. In such a case, we may observe a percentage of asbestos which is lower than the actual percentage, or not observe asbestos at all when some is present. For this reason, floor tiles reported as negative should be confirmed to be negative using transmission electron microscope (TEM) analysis. Likewise, vermiculite insulation materials containing traces of asbestiform asbestos present a problem for routine PLM analysis - the amphiboles are sometimes present in trace amounts inhomogeneously distributed. For this reason, loose vermiculite samples reported as negative should be confirmed to contain no amphibole using hydroseparation techniques.

The samples were analyzed under the following ongoing quality assurance program: Blank samples are routinely analyzed to maintain contamination-free materials. Each analyst has at least a bachelor's degree in physical science, and has also completed extensive training specific to asbestos analysis for 1-3 months before being allowed to analyze client samples. Qualitative reference samples are routinely analyzed to assure that analysts

Method: EPA 600/R-93/116Rec: 10/17/2019

Report Date: 10/22/2019 Date Analyzed: 10/22/2019

Fiberquant Internal SOP:

FACILITY SERVICES MANAGEMENT

CLARKSTON RD BLDG 30033

FT HUACHUCA, AZ

Office Phone: (520) 533-5906

FAX:

85613-0000

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 1 of 9

DRAFT

PLM Analysis Summary: Job Number: 201910185 1-8649693 can identify asbestos and asbestos-look-alike fibers. Quantitative reference samples are routinely analyzed to calibrate and characterize the estimation procedure. Microscope alignment is checked each day. Refractive index oils are calibrated at least quarterly. At least 10% of client samples are re-analyzed from scratch by a different analyst than the original, and any discrepancies are resolved for the sample and similar sample types before the results are reported. All quality checks performed for these samples were in control except as detailed in the "Analytical Notes" below. All analysts participate in interlab round robins and proficiency testing to assure competence. Fiberquant is accredited by NVLAP (Lab code

#101031) for the analysis of bulk samples for asbestos using PLM. Accreditation does not imply endorsement by the EPA, any other United States governmental agency or any private agency or association. Each lab analysis refers only to the sample tested, and may not, due to the sampling process, be representative of the material sampled. This report may not be reproduced except in full, without the approval of Fiberquant Analytical Services.

Job Analysis Notes:

Some results may have been calculated using client supplied data, such as volume or area sampled, for which Fiberquant assumes no liability for accuracy.

Sample Number Lab Number Apparent Sample Type * Asbestos Detected Yes or No

Layer Color Apparent Layer Type * Asbestos Results

Roofing2019-10185- 151428-01 Asbestos Detected? NoSample # no asbestos detectedbitumenblackLayer # 1 no asbestos detectedroof ply/bitumenblackLayer # 2 no asbestos detectedroof ply/bitumenblackLayer # 3 no asbestos detectedroof ply/bitumenblackLayer # 4 no asbestos detectedroof ply/bitumenblackLayer # 5 no asbestos detectedinsulationyellowLayer # 6 no asbestos detectedroof ply/bitumenblackLayer # 7

Roofing2019-10185- 251428-02 Asbestos Detected? NoSample # no asbestos detectedbitumenblackLayer # 1 no asbestos detectedroof ply/bitumenblackLayer # 2 no asbestos detectedroof ply/bitumenblackLayer # 3 no asbestos detectedroof ply/bitumenblackLayer # 4 no asbestos detectedroof ply/bitumenblackLayer # 5 no asbestos detectedinsulationyellowLayer # 6 no asbestos detectedroof ply/bitumenblackLayer # 7

Adhesive/caulk2019-10185- 351428-03 Asbestos Detected? NoSample # no asbestos detectedpaintsilverLayer # 1 no asbestos detectedcaulkblackLayer # 2

Roofing2019-10185- 451428-04 Asbestos Detected? NoSample # no asbestos detectedbitumenblackLayer # 1 no asbestos detectedroof ply/bitumenblackLayer # 2 no asbestos detectedroof ply/bitumenblackLayer # 3 no asbestos detectedroof ply/bitumenblackLayer # 4 no asbestos detectedroof ply/bitumenblackLayer # 5 no asbestos detectedinsulationyellowLayer # 6 no asbestos detectedroof ply/bitumenblackLayer # 7

Adhesive/caulk2019-10185- 551428-05 Asbestos Detected? NoSample # no asbestos detectedpaintredLayer # 1 no asbestos detectedcaulkgrayLayer # 2

Wall System2019-10185- 651428-06 Asbestos Detected? NoSample # no asbestos detectedpaintwhiteLayer # 1 no asbestos detectedtexture/joint compoundwhiteLayer # 2 no asbestos detectedpaper/cardboardoff-whiteLayer # 3 no asbestos detectedtexture/joint compoundwhiteLayer # 4 no asbestos detectedpaper/cardboardtanLayer # 5 no asbestos detecteddrywall corewhiteLayer # 6

TSI2019-10185- 751428-07 Asbestos Detected? NoSample # no asbestos detectedinsulation wrapsilverLayer # 1 no asbestos detectedcoatingblackLayer # 2

TSI2019-10185- 851428-08 Asbestos Detected? NoSample # no asbestos detectedsurfaceblackLayer # 1 no asbestos detectedsurfacewhiteLayer # 2

Flooring2019-10185- 951428-09 Asbestos Detected? NoSample # no asbestos detectedfloor tileoff-whiteLayer # 1 no asbestos detectedmasticgrayLayer # 2

Flooring2019-10185- 1051428-10 Asbestos Detected? YesSample # 2-5% chrysotile asbestosfloor tilegrayLayer # 1 no asbestos detectedmasticoff-whiteLayer # 2

Adhesive/caulk2019-10185- 1151428-11 Asbestos Detected? NoSample # no asbestos detectedpaintgrayLayer # 1 no asbestos detectedputtyoff-whiteLayer # 2

Adhesive/caulk2019-10185- 1251428-12 Asbestos Detected? NoSample # no asbestos detectedpaintgrayLayer # 1 no asbestos detectedputtyoff-whiteLayer # 2

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 2 of 9

* Apparent Sample Types and Apparent Layer Types are as they appeared to the analyst. Since many types of materials appear similar after sampling damage, the apparent type of material may not be the actual type of material.

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 3 of 9

PLM Analysis Details Job Number: 201910185 1-8649693

2019-10185- 151428-01 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Roofing

No

Fibrous SolidOKAn?

7# Layers NoAsbestos Detected?

Apparent Smp Type cellulose fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using solvent. Note: there appears to be more than one sample layer sequence in the bag (e.g., samples from more than one location); therefore, the reported layer sequence has been estimated/composited.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber W F N N H + U

Non-Fibrous Components (in approx. decreasing order): bitumen, polymer foam, filler

Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 20 n.d. - - - - -bitumen black 1

2 10 2-5% - - - - -roof ply/bitumen black 1

3 10 2-5% - - - - -roof ply/bitumen black 1

4 10 10-20% - - - - -roof ply/bitumen black 1

5 8 10-20% - - - - -roof ply/bitumen black 1

6 40 n.d. - - - - -insulation yellow 2

7 2 30-40% - - - - -roof ply/bitumen black 1

100Total % 2-5% - - - - -Overall %

2019-10185- 251428-02 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Roofing

No

Fibrous SolidOKAn?

7# Layers NoAsbestos Detected?

Apparent Smp Type cellulose fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using solvent. Note: there appears to be more than one sample layer sequence in the bag (e.g., samples from more than one location); therefore, the reported layer sequence has been estimated/composited.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber W F N N H + U

Non-Fibrous Components (in approx. decreasing order): polymer foam, bitumen, filler

Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 8 n.d. - - - - -bitumen black 1

2 5 5-10% - - - - -roof ply/bitumen black 1

3 5 5-10% - - - - -roof ply/bitumen black 1

4 5 5-10% - - - - -roof ply/bitumen black 1

5 5 10-20% - - - - -roof ply/bitumen black 1

6 70 n.d. - - - - -insulation yellow 2

7 2 30-40% - - - - -roof ply/bitumen black 1

100Total % 2-5% - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 4 of 9

2019-10185- 351428-03 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Adhesive/caulk

No

StickyOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type cellulose fiber Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber

W F N N H + U

Non-Fibrous Components (in approx. decreasing order): bitumen, rock, filler

Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 1 n.d. - - - - -paint silver 1

2 99 2-5% - - - - -caulk black 1

100Total % 2-5% - - - - -Overall %

2019-10185- 451428-04 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Roofing

No

Fibrous SolidOKAn?

7# Layers NoAsbestos Detected?

Apparent Smp Type cellulose fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using solvent. Note: there appears to be more than one sample layer sequence in the bag (e.g., samples from more than one location); therefore, the reported layer sequence has been estimated/composited.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber W F N N H + U

Non-Fibrous Components (in approx. decreasing order): polymer foam, bitumen, filler

Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 5 n.d. - - - - -bitumen black 1

2 5 5-10% - - - - -roof ply/bitumen black 1

3 5 5-10% - - - - -roof ply/bitumen black 1

4 5 5-10% - - - - -roof ply/bitumen black 1

5 10 5-10% - - - - -roof ply/bitumen black 1

6 65 n.d. - - - - -insulation yellow 2

7 5 30-40% - - - - -roof ply/bitumen black 1

100Total % 2-5% - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 5 of 9

2019-10185- 551428-05 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Adhesive/caulk

No

RubberyOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type none Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent. Minor adhering wall materials, paint and/or texture, etc. were not analyzed.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations none

Non-Fibrous Components (in approx. decreasing order): polymer, filler, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 2 n.d. - - - - -paint red 1

2 98 n.d. - - - - -caulk gray 1

100Total % n.d. - - - - -Overall %

2019-10185- 651428-06 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Wall System

No

Fibrous SolidOKAn?

6# Layers NoAsbestos Detected?

Apparent Smp Type cellulose fiber glass fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of paint matrix using solvent. Procedure: dissolution of joint compound/texture matrix using acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber glass fiber

W F N N H + U

CL D Y

Non-Fibrous Components (in approx. decreasing order): powder, binder, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 1 n.d. n.d. - - - -paint white 1

2 6 n.d. n.d. - - - -texture/joint compound white 3

3 5 90-100% n.d. - - - -paper/cardboard off-white 2

4 8 n.d. n.d. - - - -texture/joint compound white 3

5 5 90-100% n.d. - - - -paper/cardboard tan 2

6 75 <=1% <=1% - - - -drywall core white 3

100Total % 5-10% <=1% - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 6 of 9

2019-10185- 751428-07 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

TSI

No

Fibrous SolidOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type glass fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations glass fiber CL D Y

Non-Fibrous Components (in approx. decreasing order): polymer, filler, metal

Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 80 n.d. - - - - -insulation wrap silver 1

2 20 2-5% - - - - -coating black 1

100Total % <=1% - - - - -Overall %

2019-10185- 851428-08 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

TSI

No

Non-fibrous SolidOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type noneFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations none

Non-Fibrous Components (in approx. decreasing order): polymer, , Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 5 n.d. - - - - -surface black 1

2 95 n.d. - - - - -surface white 1

100Total % n.d. - - - - -Overall %

2019-10185- 951428-09 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type none Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

Non-Fibrous Components (in approx. decreasing order): filler, polymer, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 99 n.d. - - - - -floor tile off-white 1

2 1 n.d. - - - - -mastic gray 1

100Total % n.d. - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 7 of 9

2019-10185- 1051428-10 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

2# Layers YesAsbestos Detected?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

1.561 1.553chrysotile asbestos

1.550 db/ly sb/oW A N N L + P

Non-Fibrous Components (in approx. decreasing order): filler, polymer, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 99 2-5% - - - - -floor tile gray 1

2 1 n.d. - - - - -mastic off-white 1

100Total % 2-5% - - - - -Overall %

2019-10185- 1151428-11 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Adhesive/caulk

No

Non-fibrous SolidOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type noneFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using dilute HCl acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations none

Non-Fibrous Components (in approx. decreasing order): polymer, filler, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 1 n.d. - - - - -paint gray 1

2 99 n.d. - - - - -putty off-white 2

100Total % n.d. - - - - -Overall %

2019-10185- 1251428-12 10/16/2019Lab Number Sample Sampled:

DMSAnalyzed By 10/22/2019

Homogeneous

Adhesive/caulk

No

Non-fibrous SolidOKAn?

2# Layers NoAsbestos Detected?

Apparent Smp Type noneFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using dilute HCl acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations none

Non-Fibrous Components (in approx. decreasing order): polymer, filler, Condition: acceptable

Layers

# Layer Type % Color Friability

Calibrated Visual Estimate of Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 1 n.d. - - - - -paint gray 1

2 99 n.d. - - - - -putty off-white 2

100Total % n.d. - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 8 of 9

Fr=Friability: 1=very non-friable; 2= non-friable; 3=friable; 4=highly friable

Colors: B=black;BL=blue;BR=brown;CL=clear;G=Green;GY=gray;OR=orange;OW=off-white;PN=pink;PU=purple;R=red;TN=tan;W=white;Y=yellow;V=various

Fiber Morphology: A=fine fibers/bundles, white, sinewy, flexible; B=fine fibers/bundles, w-br, straight, broomed ends; C=fine fibers/bundles, blue, straight, broomed ends;

D=fine to coarse fibers, CL-B, brittle; E=coarse fibers,CL or dyed, striated; F=coarse fibers or splinters, W-BR, ribbon-like; G=lath-like or shards, low aspect ratio, may taper

Iso=isotropism - may be yes or no; Pleo=pleochroism - may be yes or no; Bi=birefringence - may be None, Low, Medium or High

Elg=sign of elongation - may be +, - or B (both); Ext=extinction - may be Parallel, Oblique, None or Undulating; Oil=medium used to for dispersion staining

Col Par=dispersion staining colors parallel to the fiber (fiber/halo): b/w=black/white; dg/py=dark gray/pale yellow; vg/y=violet gray/yellow; db/ly=dark blue/lemon yellow;

vb/g= vivid blue/gold; sb/o=sky blue/orange; pb/r=pale blue/red; gb/dr=gray blue/dark red; w/b=white/black. Col Perp=same only perpendicular to fiber.

RI Par=refractive index parallel to fiber; RI Perp=refractive index perpendicular to fiber

22-Oct-19Analyst: DAVID M. SCHALLER

Larry S. Pierce, Approved Accreditation Signatory

Printed:

22-Oct-19Original Print Date:

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 9 of 9

Client Job: 1-5142890 PO Number: 51428

JobNumber: 201606133

Routing Number: -

# Samples: 12

PLMn

PLM The "New" Method; see below

Client:

Polarized Light Microscope (PLM) Analysis for Asbestos in Bulk Sample

Method and Analysis Information:

Each bulk sample is first dissected under a 7-30x magnification stereo-microscope. This examination is used to determine the general type of sample, how many and what type of layers it has, and initial estimates of fiber types and quantities. Second, liquid media mounts are made of each layer - such mounts may be of selected fibers (used solely for identification purposes) or may be representative of the layer as a whole (used for quantitation purposes). The mounts may be made in a synthetic Canadian balsam, one of several solvents, or in refractive index oils (media of known refractive index). Generally, a variety of different mounts are made: some optimized for fiber visibility, some optimized for fiber identification, and some optimized for fiber quantitation. The mounted slides are then examined at 50-400x magnification on a Nikon Labphot-pol microscope. Optical characteristics are used to identify each observed fiber type; the optical data are contained for each sample on its detail analysis sheet, attached.

Current EPA and NESHAP regulations designate a result of <=1 % asbestos as "negative" and >1 % asbestos as "positive". Samples containing layers that have been determined to be "positive" may have to be handled differently during a renovation or demolition than samples whose layers have been determined to be "negative."

The method of fiber identification and quantitation is the “Standard Operating Procedures for the Analysis of Asbestos in Bulk Samples using Polarized Light Microscopy”, Chapter 7 of the Quality Assurance and Management Manual. This SOP and its associated reporting have been designed to satisfy all requirements in both EPA Method 600/M4-82-020 (The Interim Method) and EPA Method 600/R-93/116 (The New Method). The Interim Method is the required method for AHERA (US EPA 40 CFR Pt. 763), but this method calls for the reporting of composited results of multi-layered samples that is no longer an acceptable reporting practice in most circumstances. Current EPA rules, such as NESHAP (US EPA 40CFT Pt. 61), as well as NVLAP accreditation policies, call for separate reporting for each layer of multi-layered samples. The New Method contains the same procedures for identification and quantification of asbestos as does the Interim Method, except that multi-layered samples are reported to comply with the latest US

EPA rule. Fiberquant not only reports the asbestos content of each layer of multi-layered samples separately (satisfying current EPA and NVLAP reporting requirements), but Fiberquant also reports what percentage of the sample each layer comprises. Therefore, the results may be arithmetically composited to satisfy the reporting requirements of the Interim Method. The method of fiber quantitation is an estimation technique in which the analysts quantitation is routinely calibrated by reference quantitation standards, and which has been shown to be equivalent in precision and accuracy to point counting. Friability is estimated for the purposes of deciding when to point count. Friabilities determined in the field take precedence over those determined in the laboratory. Those sample layers which are friable and estimated by the analyst to contain <= 1% asbestos are point counted using 400 points. Such point counting is required by NESHAP (National Emission Standards for Hazardous Air Polutants, Nov. 1990) in order to rely on analytical results that are <= 1%. The coefficient of variation for the estimation quantitation technique is 100% in the range 0- 5%. This means that PLM analysis is not capable of conclusively determining whether a layer containing close to 1% asbestos is actually "positive" or

"negative". For this reason, Fiberquant refers to results where asbestos was detected but <= 1% as "borderline negative", and results where asbestos was >1 % but <= 2% as "borderline positive" to indicate the uncertainty in assigning a "positive" or "negative" label. In the sample summary, "ND" means that no asbestos was detected during the analysis. A "Tr" or "Trace" of asbestos reported is defined for our purposes as the detection of several asbestos fibers during the analysis; this level would be right at the limit of detection for the method. Trace is only reported on the analysis detail - in the summary a trace would be reported as <=1%. The limit of detection (the smallest % of asbestos that can be detected) varies greatly depending on the matrix in which the asbestos is found. As little as 0.001% asbestos can be detected in favorable samples, while detection in unfavorable samples may approach the detection limit of 1% stated in the method. During the analysis, the analyst, for Fiberquant identification purposes only, determines the "apparent sample type" and "apparent layer types." It must be emphasized that these types are only what is apparent. Often, different materials appear similar or identical after sampling, so the analyst may assign a type other than what was sampled.

Floor tiles present a special problem for PLM asbestos analysis. Floor tile can contain chrysotile fibers so thin that they cannot be resolved by optical methods. In such a case, we may observe a percentage of asbestos which is lower than the actual percentage, or not observe asbestos at all when some is present. For this reason, floor tiles reported as negative should be confirmed to be negative using transmission electron microscope

(TEM) analysis. Likewise, vermiculite insulation materials containing traces of asbestiform asbestos present a problem for routine PLM analysis - the amphiboles are sometimes present in trace amounts inhomogeneously distributed. For this reason, loose vermiculite samples reported as negative should be confirmed to contain no amphibole using hydroseparation techniques.

The samples were analyzed under the following ongoing quality assurance program: Blank samples are routinely analyzed to maintain contamination-free materials. Each analyst has at least a bachelor's degree in physical science, and has also completed extensive training specific to asbestos analysis for 1-3 months before being allowed to analyze client samples. Qualitative reference samples are routinely analyzed to assure that analysts can identify asbestos and asbestos-look-alike fibers. Quantitative reference samples are routinely analyzed to calibrate and characterize the

Method: EPA 600/R-93/116Rec: 6/16/2016

Report Date: 6/21/2016 Date Analyzed: 6/21/2016

Fiberquant Internal SOP:

EMCOR GOVERNMENT SVCS

CLARKSTON RD BLDG 30033

FT HUACHUCA, AZ

Office Phone: (520) 533-5906

FAX: (520) 533-3699

85613-0000

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 1 of 10

PLM Analysis Summary: Job Number: 201606133 1-5142890 estimation procedure. Microscope alignment is checked each day. Refractive index oils are calibrated at least quarterly. At least 10% of client samples are re-analyzed from scratch by a different analyst than the original, and any discrepancies are resolved for the sample and similar sample types before the results are reported. All quality checks performed for these samples were in control except as detailed in the "Analytical Notes" below. All analysts participate in interlab round robins and proficiency testing to assure competence. Fiberquant is accredited by NVLAP (Lab #101031) for the analysis of bulk samples for asbestos using PLM. Accreditation does not imply endorsement by the EPA, any other United States governmental agency or any private agency or association. Each lab analysis refers only to the sample tested, and may not, due to the sampling process, be representative of the material sampled. This report may not be reproduced except in full, without the approval of Fiberquant Analytical

Services.

Job Analysis Notes:

Some results may have been calculated using client supplied data, such as volume or area sampled, for which Fiberquant assumes no liability for accuracy.

Sample Number Lab Number Apparent Sample Type * Positive Layer Yes or No

Layer Color Apparent Layer Type * Asbestos Results

Miscellaneous2016-06133- 151428-01 Positive Layer? NoSample # no asbestos detectedbase coveblueLayer # 1 no asbestos detectedmasticoff-whiteLayer # 2

Flooring2016-06133- 251428-02 Positive Layer? YesSample # no asbestos detectedfloor tileoff-whiteLayer # 1 no asbestos detectedmasticyellowLayer # 2

>1-2% chrysotile asbestosfloor tilebrownLayer # 3 no asbestos detectedmastictanLayer # 4 no asbestos detectedmasticblackLayer # 5

5-10% chrysotile asbestosfloor tiletanLayer # 6 no asbestos detectedmastictanLayer # 7

Adhesive/caulk2016-06133- 351428-03 Positive Layer? NoSample # no asbestos detectedpaintvariousLayer # 1

<=1% chrysotile asbestossealantgrayLayer # 2

Wall System2016-06133- 451428-04 Positive Layer? NoSample # no asbestos detectedpaintoff-whiteLayer # 1 no asbestos detectedtexture/joint compoundwhiteLayer # 2 no asbestos detectedpaper/cardboardoff-whiteLayer # 3 no asbestos detectedtexture/joint compoundwhiteLayer # 4 no asbestos detectedpaper/cardboardtanLayer # 5 no asbestos detecteddrywall coreoff-whiteLayer # 6

Flooring2016-06133- 551428-05 Positive Layer? YesSample # 2-5% chrysotile asbestosfloor tiletanLayer # 1 no asbestos detectedmastictanLayer # 2 no asbestos detectedpaintgrayLayer # 3 no asbestos detectedleveling compoundoff-whiteLayer # 4

Adhesive/caulk2016-06133- 651428-06 Positive Layer? NoSample # no asbestos detectedpaintvariousLayer # 1

<=1% chrysotile asbestossealantgrayLayer # 2

Miscellaneous2016-06133- 751428-07 Positive Layer? NoSample # no asbestos detectedbase coveblueLayer # 1 no asbestos detectedmasticoff-whiteLayer # 2

Wall System2016-06133- 851428-08 Positive Layer? NoSample # no asbestos detectedpaintoff-whiteLayer # 1 no asbestos detectedtexture/joint compoundwhiteLayer # 2 no asbestos detectedpaper/cardboardoff-whiteLayer # 3 no asbestos detectedtexture/joint compoundwhiteLayer # 4 no asbestos detectedpaper/cardboardtanLayer # 5 no asbestos detecteddrywall corewhiteLayer # 6

Flooring2016-06133- 951428-09 Positive Layer? YesSample # no asbestos detectedfloor tileoff-whiteLayer # 1

>1-2% chrysotile asbestosfloor tiletanLayer # 2 no asbestos detectedleveling compoundoff-whiteLayer # 3

Flooring2016-06133- 1051428-10 Positive Layer? YesSample # no asbestos detectedfloor tileoff-whiteLayer # 1 no asbestos detectedleveling compoundtanLayer # 2

>1-2% chrysotile asbestosfloor tiletanLayer # 3 no asbestos detectedmastictanLayer # 4 no asbestos detectedpaintgrayLayer # 5

Acoustical Tile2016-06133- 1151428-11 Positive Layer? NoSample # no asbestos detectedpaintwhiteLayer # 1 no asbestos detectedacoustical tileoff-whiteLayer # 2

Cementitious2016-06133- 1251428-12 Positive Layer? NoSample # no asbestos detectedpaintoff-whiteLayer # 1 no asbestos detectedconcretegrayLayer # 2

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 2 of 10

* Apparent Sample Types and Apparent Layer Types are as they appeared to the analyst. Since many types of materials appear similar after sampling damage, the apparent type of material may not be the actual type of material.

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 3 of 10

PLM Analysis Details Job Number: 201606133 1-5142890

2016-06133- 151428-01 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Miscellaneous

No

RubberyOKAn?

2# Layers NoPos Layer?

Apparent Smp Type none Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent. Minor adhering wall paint and/or texture, etc. not analyzed. Surface of covebase was brown.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

5# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 98 n.d. - - - - -base cove blue 1

2 2 n.d. - - - - -mastic off-white 1

100Total % n.d. - - - - -Overall %

2016-06133- 251428-02 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

7# Layers YesPos Layer?

Apparent Smp Type chrysotile asbestos cellulose fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent. Black mastic was too thin to analyze and may have been contamination.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

1.561 1.553chrysotile asbestos cellulose fiber

1.550 db/ly sb/oW A N N L + P

W F N N H + U

Non-Fibrous Components (in approx. decreasing order): filler, polymer, 14# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 33 n.d. n.d. - - - -floor tile off-white 1

2 1 n.d. n.d. - - - -mastic yellow 1

3 32 >1-2% <=1% - - - -floor tile brown 1

4 1 n.d. n.d. - - - -mastic tan 1

5 0.5 n.d. n.d. - - - -mastic black 1

6 30.5 5-10% n.d. - - - -floor tile tan 1

7 2 n.d. n.d. - - - -mastic tan 1

100Total % 2-5% <=1% - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 4 of 10

2016-06133- 351428-03 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Adhesive/caulk

No

Fibrous SolidOKAn?

2# Layers NoPos Layer?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent. Note: Material is point-countable.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

Non-Fibrous Components (in approx. decreasing order): powder, filler, 4# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 3 n.d. - - - - -paint various 1

2 97 <=1% - - - - -sealant gray 1

100Total % <=1% - - - - -Overall %

2016-06133- 451428-04 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Wall System

No

Fibrous SolidOKAn?

6# Layers NoPos Layer?

Apparent Smp Type cellulose fiber glass fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of paint matrix using solvent. Procedure: dissolution of joint compound/texture matrix using acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber glass fiber

W F N N H + U

CL D Y

Non-Fibrous Components (in approx. decreasing order): powder, binder, 13# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 2 n.d. n.d. - - - -paint off-white 1

2 4 n.d. n.d. - - - -texture/joint compound white 3

3 2 90-100% n.d. - - - -paper/cardboard off-white 2

4 3 n.d. n.d. - - - -texture/joint compound white 3

5 5 90-100% n.d. - - - -paper/cardboard tan 2

6 84 n.d. <=1% - - - -drywall core off-white 3

100Total % 5-10% <=1% - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 5 of 10

2016-06133- 551428-05 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

4# Layers YesPos Layer?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

Non-Fibrous Components (in approx. decreasing order): filler, polymer, powder

9# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 75 2-5% - - - - -floor tile tan 1

2 1 n.d. - - - - -mastic tan 1

3 3 n.d. - - - - -paint gray 1

4 21 n.d. - - - - -leveling compound off-white 3

100Total % 2-5% - - - - -Overall %

2016-06133- 651428-06 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Adhesive/caulk

No

Non-fibrous SolidOKAn?

2# Layers NoPos Layer?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent. Procedure: dissolution of matrix using dilute HCl acid. Note: Material is point-countable.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

Non-Fibrous Components (in approx. decreasing order): powder, filler, binder

4# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 2 n.d. - - - - -paint various 1

2 98 <=1% - - - - -sealant gray 1

100Total % <=1% - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 6 of 10

2016-06133- 751428-07 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Miscellaneous

No

RubberyOKAn?

2# Layers NoPos Layer?

Apparent Smp Type none Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of polymer matrix using solvent. Minor adhering wall paint and/or texture, etc. not analyzed.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

5# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 95 n.d. - - - - -base cove blue 1

2 5 n.d. - - - - -mastic off-white 1

100Total % n.d. - - - - -Overall %

2016-06133- 851428-08 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Wall System

No

Fibrous SolidOKAn?

6# Layers NoPos Layer?

Apparent Smp Type cellulose fiber Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of paint matrix using solvent. Procedure: dissolution of joint compound/texture matrix using acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber

W F N N H + U

Non-Fibrous Components (in approx. decreasing order): powder, binder, 13# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 2 n.d. - - - - -paint off-white 1

2 3 n.d. - - - - -texture/joint compound white 3

3 3 90-100% - - - - -paper/cardboard off-white 2

4 3 n.d. - - - - -texture/joint compound white 3

5 5 90-100% - - - - -paper/cardboard tan 2

6 84 <=1% - - - - -drywall core white 3

100Total % 5-10% - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 7 of 10

2016-06133- 951428-09 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

3# Layers YesPos Layer?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent. Note: Not enough mastic was present for analysis. Note: analysis results were confirmed by a second analyst. Note: It is recommended that the tan tile be confirmed by TEM.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations

10# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 67 n.d. - - - - -floor tile off-white 1

2 30 >1-2% - - - - -floor tile tan 1

3 3 n.d. - - - - -leveling compound off-white 3

100Total % <=1% - - - - -Overall %

2016-06133- 1051428-10 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Flooring

No

Non-fibrous SolidOKAn?

5# Layers YesPos Layer?

Apparent Smp Type chrysotile asbestos Fiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of floor tile matrix and mastic using solvent. Note: It is recommended that the tan tile be confirmed by TEM. Note: The presence of chysotile is reported here, but the chrysotile identity could not be confirmed by all of its optical characteristics due to the small size of the fibers in this sample; it is recommended that the identification of chrysotile be confirmed using TEM.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations chrysotile asbestos

W A N N L + P

13# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 39 n.d. - - - - -floor tile off-white 1

2 1 n.d. - - - - -leveling compound tan 3

3 55 >1-2% - - - - -floor tile tan 1

4 1 n.d. - - - - -mastic tan 1

5 4 n.d. - - - - -paint gray 1

100Total % <=1% - - - - -Overall %

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 8 of 10

2016-06133- 1151428-11 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Acoustical Tile

No

Fibrous MatOKAn?

2# Layers NoPos Layer?

Apparent Smp Type cellulose fiber glass fiberFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of paint matrix using solvent. Procedure: dissolution of acoustical tile using acid.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations cellulose fiber glass fiber

W F N N H + U

CL D Y

Non-Fibrous Components (in approx. decreasing order): perlite, powder, binder

4# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 2 n.d. n.d. - - - -paint white 1

2 98 40-50% 5-10% - - - -acoustical tile off-white 3

100Total % 40-50% 5-10% - - - -Overall %

2016-06133- 1251428-12 6/14/2016Lab Number Sample Sampled:

RAMAnalyzed By 6/21/2016

Homogeneous

Cementitious

No

Non-fibrous SolidOKAn?

2# Layers NoPos Layer?

Apparent Smp Type noneFiber Identification:

Sample Analytical Note

Procedure: tweased apart using forceps. Procedure: dissolution of matrix using dilute HCl acid. Procedure: dissolution of matrix using solvent.

Fibers

Color Mrph Iso Pleo Bi Elg Ext Oil Col Par Col Per RI Par RI Per

Refractive Index Determinations none

Non-Fibrous Components (in approx. decreasing order): powder, rock, binder

4# Sub-Samples

Condition: acceptable

Layers

# Layer Type % Color Friability

Percents of Each Fiber

Fib 1 Fib 2 Fib 3 Fib 4 Fib 5 Fib 6

1 3 n.d. - - - - -paint off-white 1

2 97 n.d. - - - - -concrete gray 1

100Total % n.d. - - - - -Overall %

Fr=Friability: 1=very non-friable; 2= non-friable; 3=friable; 4=highly friable

Colors: B=black;BL=blue;BR=brown;CL=clear;G=Green;GY=gray;OR=orange;OW=off-white;PN=pink;PU=purple;R=red;TN=tan;W=white;Y=yellow;V=various

Fiber Morphology: A=fine fibers/bundles, white, sinewy, flexible; B=fine fibers/bundles, w-br, straight, broomed ends; C=fine fibers/bundles, blue, straight, broomed ends;

D=fine to coarse fibers, CL-B, brittle; E=coarse fibers,CL or dyed, striated; F=coarse fibers or splinters, W-BR, ribbon-like; G=lath-like or shards, low aspect ratio, may taper

Iso=isotropism - may be yes or no; Pleo=pleochroism - may be yes or no; Bi=birefringence - may be None, Low, Medium or High

Elg=sign of elongation - may be +, - or B (both); Ext=extinction - may be Parallel, Oblique, None or Undulating; Oil=medium used to for dispersion staining

Col Par=dispersion staining colors parallel to the fiber (fiber/halo): b/w=black/white; dg/py=dark gray/pale yellow; vg/y=violet gray/yellow; db/ly=dark blue/lemon yellow;

vb/g= vivid blue/gold; sb/o=sky blue/orange; pb/r=pale blue/red; gb/dr=gray blue/dark red; w/b=white/black. Col Perp=same only perpendicular to fiber.

RI Par=refractive index parallel to fiber; RI Perp=refractive index perpendicular to fiber

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 9 of 10

21-Jun-16Analyst: ROBERT A. McCORMICK

Larry S. Pierce, Approved Accreditation Signatory

Printed:

21-Jun-16Original Print Date:

5025 S. 33rd Street Phoenix, Arizona 85040-2816 Phone: 602-276-6139 1-800-743-2687 FAX: 602-276-4558

Fiberquant, Inc. Page 10 of 10