Install CCTV Station Islamorada.pdf

SCOPE OF WORK

FOR

INSTALL CCTV CAMERAS AND MONITORING EQUIPMENT

PROJECT #20200505

AT

U.S. COAST GUARD STATION ISLAMORADA

183 PALERMO DRIVE

ISLAMORADA, FL 33036

May 2020

US Coast Guard Station Islamorada Project No. 20200505 Install CCTV Cameras and Monitoring Equipment

TABLE OF CONTENTS TOC-1 / 1

TABLE OF CONTENTS

DIVISION 1 - GENERAL REQUIREMENTS

011000 SUMMARY OF WORK

DIVISION 28 – ELECTRONIC SAFETY AND SECURITY

282300 VIDEO SURVEILLANCE

ENCLOSURES

1. PROJECT DRAWING – SITE PLAN

END OF CONTENTS

SUMMARY 011000 - 1 / 3

SECTION 011000 - SUMMARY

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Project information.

2. Work covered by contract documents.

3. Phased construction.

4. Work by Government.

5. Access to site.

6. Coordination with occupants.

7. Work restrictions.

8. Safety precautions.

9. Site maintenance.

1.2 PROJECT INFORMATION

A. Project Identification: Install CCTV Cameras & Monitoring Equipment – Project #20200505.

1. Project Location: US Coast Guard Station Islamorada, 183 Palermo Drive, Islamorada, Florida 33036.

1.3 SCOPE OF WORK COVERED BY CONTRACT DOCUMENTS

A. The work of project is defined by the contract documents and consists of the following:

1. In general, the project consists of all work, including labor, equipment and materials, necessary to install power over ethernet cameras, monitoring equipment and software, and related hardware/accessories at Coast Guard Station Islamorada.

WORK SEQUENCE

A. The work shall be conducted by the contractor to provide the least possible interference to the activities of government personnel.

SUMMARY 011000 - 2 / 3

B. Please provide notification to Coast Guard at least one full week prior to starting work.

1.4 WORK BY GOVERNMENT

A. General: Cooperate fully with Government so work may be carried out smoothly, without interfering with or delaying work under this contract or work by Government.

Coordinate the work of this contract with work performed by Government.

1.5 ACCESS TO SITE

A. General: During the construction period the contractor shall have limited use of project site for construction operations as indicated on drawings, as indicated by requirements of this Section, and as specified by the Contracting Officer.

1. Material storage and work areas shall be as designated by the Contracting Officer’s Representative (COR).

B. Pre-Bid Site Visit: Contractors are encouraged but not obligated to visit the site to note existing site conditions. To make arrangements to visit the site, please contact:

1. MLES2 Dale Stauffer

Sector Key West Security Officer Email: Dale.K.Stauffer@uscg.mil Phone: (305) 292-8805

1.6 WORK RESTRICTIONS

A. Work Restrictions, General: Comply with restrictions on construction operations.

1. Comply with limitations on use of public streets and with other requirements of authorities having jurisdiction.

B. On-Site Work Hours: Limit work in the existing building to normal business working hours of 7:00 a.m. to 4:00 p.m., Monday through Friday, unless otherwise indicated.

1. Submit request to the COR at least 72 hours in advance for permission to work outside the normal working hours or on Saturdays, Sundays, or federal holidays.

C. Existing Utility Interruptions: Do not interrupt utilities serving facilities occupied by Government or others unless permitted under the following conditions:

1. Submit request to the COR at least 72 hours in advance of proposed utility interruptions.

2. Obtain COR’s written permission before proceeding with utility interruptions.

D. Take action to prevent the spread of construction dust and debris.

SUMMARY 011000 - 3 / 3

1.7 SITE MAINTENANCE

A. The contractor shall perform daily clean-up of work site, dumpsters and storage area.

All dumpsters shall be covered and watertight should a contractor choose to utilize one.

PART 2 - PRODUCTS (Not Used)

PART 3 - EXECUTION (Not Used)

END OF SECTION 011000

US Coast Guard Sector Key West Project No. 20200505

VIDEO SURVEILLANCE 282300 - 1/7

SECTION 282300 - VIDEO SURVEILLANCE

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes a video surveillance system consisting of cameras, digital video recorder, data transmission wiring, monitoring station, and other associated equipment.

B. Contractor shall provide and install all labor equipment, and materials explicitly listed below as well as any necessary ancillary products required to provide a fully functional turn key product.

1.2 ACTION SUBMITTALS

A. Product Data: For each type of product indicated. Include dimensions and data on features, performance, electrical characteristics, ratings, and finishes. Please note on any products where the Coast Guard must make a selection (example: color choices). Submit cut sheets on each item for Coast Guard approval prior to installation.

1.3 CLOSEOUT SUBMITTALS

A. At the completion of installation, contractor shall provide manufacturers Operation and maintenance data on all pieces of equipment.

1.4 QUALITY ASSURANCE

A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

B. Comply with NECA 1.

C. Comply with NFPA 70 "National Electrical Code."

1.5 PROJECT CONDITIONS

A. Environmental Conditions: Capable of withstanding the following environmental conditions without mechanical or electrical damage or degradation of operating capability:

1. Interior, Controlled Environment: System components, installed in air-conditioned interior environments shall be rated for continuous operation in ambient temperatures of 36 to 80 deg and 20 to 80 percent relative humidity, noncondensing.

2. Exterior Environment: System components installed in locations exposed to weather shall be rated for continuous operation in ambient temperature of minus 30 to plus 122 degrees F dry bulb temperature minimum and 20 to 90 percent relative humidity, condensing.

VIDEO SURVEILLANCE 282300 - 2/7

Rate for continuous operation when exposed to rain as specified in NEMA 250, winds up to 85 mph. Use NEMA 4X type enclosures. System components are being installed in a coastal zone and shall be subject to wind-driven salt spray.

3. Security Environment: Ensure Camera housing and other infrastructure components for surveillance equipment is installed in a manner, which makes it less susceptible to physical striking and sabotages.

1.6 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of cameras, equipment related to camera operation, and control-station equipment that fail in materials or workmanship within specified warranty period.

1. Warranty Period: 1 year from date of Substantial Completion on all equipment.

PART 2 - PRODUCTS

2.1 Surge Protection: Protect components from voltage surges entering through power, communication, signal, control, or sensing leads. Include surge protection for external wiring of each conductor's entry connection to components.

2.2 STANDARD CAMERAS

A. Manufacturers: Subject to compliance with requirements, provide products by the following manufacturer or an approved equal with the same minimum salient characteristics.

B. Exterior Grade Dual Lens Multi-Directional Camera Model - Basis of Design Information:

1. Manufacturer: Hanwha Techwin America

2. Model: 2 x 2M Multi-Directional Camera

3. Model Number: PNM-7000VD

4. Quantity: 1 camera unit.

5. Salient Characteristics:

a. Exterior Grade

b. 2 Camera Lenses

c. Motion Detection Capable

d. Image Stabilization

e. Lens Distortion Correction Capable

f. Wide Dynamic Range: 150 dB

g. Resolution (Megapixels): Minimum 2 MP / 1920 x 1080 resolution

h. Frames per Second: 60 fps @ 2M (H.265/H.264)

i. Digital Zoom: 24 times minimum.

j. Electrical Source: Power over Ethernet (IEEE802.3af, Class 3)

C. Exterior Grade Infrared Dome Camera Model – Basis of Design Information:

1. Manufacturer: Hanwha Techwin America

2. Model: 2 MP Network Infrared Vandal Resistant Dome Camera

VIDEO SURVEILLANCE 282300 - 3/7

3. Model Number: QNV-6012R

4. Quantity: 4 cameras

5. Salient Characteristics:

a. Exterior Grade

b. Vandal Resistant Dome Enclosure

c. Motion Detection Capable

d. Resolution (Megapixels): Minimum 2 MP / 1920 x 1080 resolution

e. Frames per Second: 30 fps @ 2M (H.265/H.264)

f. Infrared Viewable Length: 20m (65 ft)

g. Wide Dynamic Range: 120 dB

h. Electrical Source: Power over Ethernet (IEEE802.3af, Class 3), 12VDC

D. Exterior Grade Infrared Pan, Tilt, Zoom Camera Model – Basis of Design Information:

1. Manufacturer: Hanwha Techwin America

2. Model: 2 MP 55x Zoom Network Infrared Pan, Tilt, Zoom Camera

3. Model Number: XNP-6550RH

4. Quantity: 1 camera

5. Salient Characteristics:

a. Exterior Grade

b. Motion Detection Capable

c. Auto Tracking Capable

d. Resolution (Mega Pixels): Minimum 2 MP / 1920 x 1080 resolution

e. Wide Dynamic Range: 120 dB

f. Infrared Viewable Length: 500 m (1640 ft)

g. Operational Capabilities:

1) Tilt Range: 95 degrees (-5 to 90 degrees)

2) Tilt Speed: 250 degrees per second

3) Tilt Speed (Manual): .03 degrees per second to 250 degrees per second

4) Pan Range: 360 degrees (Endless)

5) Pan Speed: 400 degrees per second

6) Pan Speed (Manual): .03 degrees per second to 250 degrees per second

7) Zoom: 55 times

h. Electrical Source: 24V AC / HPoE

E. Exterior Grade Panoramic Camera – Basis of Design Information:

1. Manufacturer: Hanwha Techwin America

2. Model: 15 MP Multi-Sensor Panoramic Camera

3. Model Number: PNM-9030V

4. Quantity: 3 cameras

5. Salient Characteristics:

a. Exterior Grade

b. Motion Detection Capable

c. Resolution (Megapixels): Minimum 15 MP / 6096 x 2540 @ 180 degrees

d. Frames Per Second: 30 fps minimum.

e. Pan/Tilt Range: 355 degrees / 60 degrees

f. Angular Field of View: 180 degrees minimum

g. Wide Dynamic Range: 120 dB

h. Electrical Source: Power over Ethernet (IEEE802.3at, Class 4), 12VDC

F. Exterior Grade Pan, Tilt, Zoom, Rotate Camera – Basis of Design Information;

1. Manufacturer: Hanwha Techwin America

VIDEO SURVEILLANCE 282300 - 4/7

2. Model: 2 MP Vandal Resistant, Pan, Tilt, Zoom, Rotate, Network Dome Camera

3. Model Number: XNV-6085

4. Quantity: 4 cameras

5. Salient Characteristics;

a. Exterior Grade

b. Motion Detection Capable

c. Wide Dynamic Range: 150 dB

d. Resolution (Megapixels): 2 MP / 1920 x 1080 resolution

e. Angular Field of View: 100 degrees

f. Operational Capabilities:

1) Pan / Tilt / Rotate Range: ± 175 degrees | ± 73 degrees | ± 175 degrees

g. Electrical Source: Power over Ethernet (IEEE802.3af, Class 3), 12VDC

G. Notes: Provide all necessary hardware including mounting brackets, junction boxes, and conduit as necessary to install cameras. Provide any software licensing to support cameras.

2.3 COLOR MONITORS

A. Manufacturers: Subject to compliance with requirements, provide products by the following manufacturers or an approved equal with the same minimum salient characteristics.

B. Color LED Monitor Type 1 – Basis-of-Design Information:

1. Manufacturer: Dell

2. Model: C5517H - 55” Screen LED-Lit Monitor

3. Quantity: 1

4. Salient Characteristics

a. Resolution: 1920 x 1080p

b. Screen Size: 55”

c. Refresh Rate: 60 Hz

5. Note: Provide mounting bracket and necessary hardware for wall-mounted installation.

This monitor shall be installed in the Station’s command center as part of the primary monitoring and control station.

C. Color LED Monitor Type 2 – Basis-of-Design Information:

1. Manufacturer: Costar Video

2. Model:CM40HD – 40” LED Security Monitor

3. Quantity: 1

4. Salient Characteristics:

a. Resolution: 1920 x 1080p

b. Screen Size: 40”

c. Refresh Rate: 60 Hz minimum

5. Note: Provide mounting bracket and necessary hardware for wall-mounted installation.

This monitor shall be installed in the Station’s Officer of the Day room and mirror camera feeds from primary monitoring and control station.

VIDEO SURVEILLANCE 282300 - 5/7

2.4 DESKTOP COMPUTER & ACCESSORIES

A. Manufacturers: Subject to compliance with requirements, provide products by the following manufacturers or an approved equal with the same minimum salient characteristics. Install items in Station Command Center to constitute a primary monitoring and control station.

B. Desktop Security Computer / Monitoring Station

1. Manufacturer: Hanwha Techwin America

2. Model: WWTP3200W -

3. Hard Drive: 256 gb solid state drive

4. Processor: Intel Core i3 or equivalent

5. Memory: 8gb Random Access Memory

6. Graphics Processing Unit: Nvidia Quadro P400 GPU

7. Mouse & Keyboard included.

8. Quantity: 1

9. Software installed Wisenet Wave Video Management Software (include license for activated product).

C. Network Video Recorder

1. Manufacturer: Hanwha Techwin America

2. Model: WPE200W28 – Wave NYWK Video Recorder

3. Storage Size: 28 Terabytes

4. Digital Video Recording capability

5. Provide Server Rack to mount NVR.

D. Control Key Board with Joystick

1. Provide control keyboard with Joystick to cycle cameras and operate pan, tilt, zoom, and rotate functions.

2. Manufacturer: Samsung

3. Model: SPC-1010

4. Joystick Speed Control: 3-axis twist zoom)

5. Control Capacity: Up to 255 cameras

2.5 GENERAL

A. The contractor shall provide and install all of the networking equipment required to support new cameras at the specified locations and new monitoring stations. Monitoring station in the Command Center shall be capable of viewing all existing and new camera feeds by cycling through to desired camera view. Contractor is responsible for ensuring all existing server, software, and recording equipment can properly support additional cameras. Contractor shall provide and install additional software licenses, cabling, conduit, mounting brackets, security panels, server upgrades, etc. necessary to achieve a fully functional system.

VIDEO SURVEILLANCE 282300 - 6/7

PART 3 - EXECUTION

3.1 GENERAL INSTALLATION

A. All video surveillance components shall tie into one complete system with a monitoring station setup in the Station Islamorada’s command center. Contractor shall provide and install any necessary additional hardware or software not explicitly specified in this section to ensure a fully functioning system.

3.2 WIRING

A. Wiring Method: Install cables in security type tamper proof raceways or conduit unless otherwise indicated.

1. Raceways are not required in non-accessible indoor ceiling spaces and attics.

2. Raceways are not required in hollow gypsum board partitions.

3. Conceal raceways and wiring except in unfinished spaces.

3.3 VIDEO SURVEILLANCE SYSTEM INSTALLATION

A. Install cameras in locations shown in enclosed drawings. Setup main monitoring with control capability in Station Islamorada’s command center with larger monitor. Provide second monitor in Station Islamorada’s officer of the day room providing remote viewing of cameras but no control features.

B. Set pan-and-tilt unit stops to suit final camera position and to obtain the field of view required for camera. Connect all controls and alarms, and adjust.

3.4 FIELD QUALITY CONTROL

A. Tests and Inspections:

1. Inspection: Verify that units and controls are properly installed, connected, and labeled, and that interconnecting wires and terminals are identified.

2. Pretesting: Align and adjust system and pretest components, wiring, and functions to verify that they comply with specified requirements. Conduct tests at varying lighting levels, including day and night scenes as applicable. Demonstrate successful operation to the Coast Guard.

B. Video surveillance system will be considered defective if it does not pass tests and inspections.

VIDEO SURVEILLANCE 282300 - 7/7

3.5 TRAINING

A. Provide training to Coast Guard's personnel to adjust, operate, and maintain video-surveillance equipment.

END OF SECTION 282300

1 2 3 4

C C

B B

A A

2 3 4

Notes

U. S. COAST GUARD

SECTOR KEY WEST

ENGINEERING

U.S. COAST GUARD SECTOR KEY WEST

100 TRUMBO RD.

KEY WEST, FL 33040

ISSUE

1 5 5 2020 Bid Documents

MARK DATE DESCRIPTION

A/E PROJECT NO:

CAD FILE NAME: CC-0520.dwg DESIGNED BY: L. McCUE DRAWN BY: L. McCUE

EDITED BY:

CHECKED BY:

SCALE: AS NOTED PLOT SCALE: 1 = 1

SHEET TITLE

INSTALL CCTV & MONITORING

EQUIPMENT STATION ISLAMORADA

ISLAMORADA

CIVIL

SITE PlAN

REVIEWED BY: APPROVED BY:

L. McCUE L. McCUE

FL

PROJECT ENG. ENGINEERING OFFICER

LP. McCUE 5/5/2020

CHIEF OF DIVISION DATE

PROJECT NUMBER DRAWING NUMBER

CC-052020200505

DISCIPLINE SHT NO

C101 SHEET 1 OF 1

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Typewritten Text = Exterior Infrared Dome Camera

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Typewritten Text = Exterior PTZR Dome Camera

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Typewritten Text = Exterior PTZ Infrared Camera

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Rectangle

LPMcCue Rectangle

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Typewritten Text = Panoramic Camera

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Typewritten Text = Dual Lens Multi-Direction Camera install near lobby/hallway foyer

LPMcCue Typewritten Text = Approximate Line of Site. Adjust as necessary.

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Line

LPMcCue Rectangle

LPMcCue Line

LPMcCue Text Box Install Camera to provide coverage of rear door.