Install_a_Monorail_Fall_Protection_System_at_Globe_Hollow_Water_Treatment_Facility_(Addendum_#1_Revision).pdf

REQUEST FOR PROPOSAL

22/23-24

INSTALL A MONORAIL FALL PROTECTION SYSTEM AT GLOBE

HOLLOW WATER TREATMENT FACILITY

Town of Manchester

Lincoln Center

Manchester, CT 06040

RELEASE DATE: October 21, 2022

DEADLINE FOR QUESTIONS: December 2, 2022

RESPONSE DEADLINE: December 16, 2022, 11:00 am

RESPONSES MUST BE SUBMITTED ELECTRONICALLY TO:

https://secure.procurenow.com/portal/townofmanchester https://secure.procurenow.com/portal/%7bproject.government.code%7d

Town of Manchester

REQUEST FOR PROPOSAL

22/23-24

Install a Monorail Fall Protection System at Globe Hollow Water

Treatment Facility

I. Introduction

II. INSTRUCTIONS TO BIDDERS

III. STANDARD INSTRUCTIONS TO BIDDERS

IV. Project Details

V. STANDARD INSURANCE AND INDEMNIFICATION REQMNTS

VI. Living Wage Ordinance VII. Evaluation Criteria

VIII. Vendor Submissions

Attachments:

T - Manchester living wage certification

U - Plain and Trussed Monorail FP Ssytem

V - Drawing S001

W - Drawing S501

X - Drawing S101

Y - Gantry Cranes

Request For Proposal #22/23-24 Title: Install a Monorail Fall Protection System at Globe Hollow Water Treatment Facility

1. INTRODUCTION

1.1. Summary

The Town of Manchester Water & Sewer Department (MWDS) has identified the need to install a plain and trussed monorail fall protection system with gantry cranes on the sedimentation basins at the Globe

Hollow Water Treatment Plant. We are seeking proposals from qualified Contractors for fabrication, delivery, installation, and training on a Fall Protection System design provided in this proposal.

Engineered fall protection systems such as DBI/Sala or MSA will be given priority

The target implementation date for this service is January 1, 2023 and completion of work should be no later than six (6) months after start of work.

1.2. Background

The Globe Hollow Water Treatment Plant (GHWTP) uses a sedimentation basin containing four single chambers to remove precipitated solids from the drinking water. Sediments are removed by a chain driven aluminum framed float. Occasional maintenance requires water treatment operators to walk out over the water on an approximately 6-inch-wide concrete wall that separates the individual sedimentation chambers. The proposed fall protection system will prevent operators from falling into the water or contacting the float while performing maintenance.

MANDATORY SITE VISIT - A mandatory pre-bid site visit is required of all interested bidders. The Town will not accept proposals from companies who do not attend. The site visit is scheduled for November

17, 2022 at 10:00 a.m. Bidders shall meet at 125 Spring Street, Manchester, CT.

1.3. Contact Information

Cora Narracci

Purchasing Agent

494 Main Street

Purchasing Department

Manchester, CT 06040

Email: cnarracci@manchesterct.gov

Phone: (860) 647-3031

Department:

Water and Sewer

Department Head:

Pat Kearney

Director

1.4. Timeline

Release Project Date October 21, 2022 mailto:cnarracci@manchesterct.gov tel:(860)647-3031

Pre-Bid Meeting (Mandatory) November 17, 2022, 10:00am

125 Spring Street, Manchester, CT

Question Submission Deadline December 2, 2022, 4:30pm

Submission Deadline December 16, 2022, 11:00am

2. INSTRUCTIONS TO BIDDERS

2.1. ELECTRONIC BIDDING INFORMATION

Submitting Proposals

Specifications and proposal forms must be obtained online at Town of Manchester Procurement Portal

(opengov.com). The exclusive means by which all prospective bidders may obtain proposal packages, direct inquiries, request and receive addenda and supplemental information, and submit bids and proposals, shall be through the Town of Manchester’s OpenGov portal.

Proposals may be received up to the deadline date and time listed in the solicitation documents, via the

Town’s e-Procurement Portal. The Town e-Procurement Portal Clock is the official clock for the determination of all deadline dates and times. Without exception, responses will not be accepted after the submission deadline regardless of any technical difficulties such as poor internet connections. The

Town of Manchester strongly recommends completing your response well ahead of the deadline.

Addenda Notification and Acknowledgement

Addenda Notification: Bidders are required to register for an account via the Town’s e-Procurement

Portal hosted by OpenGov. Once the bidder has completed registration, you will receive addenda notifications to your email by clicking “Follow” on this project. Ultimately, it is the sole responsibility of each bidder to periodically check the site for any addenda at Town of Manchester Procurement Portal

(opengov.com)

Submitting Questions and Receiving Responses

Bidders shall submit all inquiries regarding this RFP via the Town’s e-Procurement Portal. Please note any deadline for submitting inquiries. All answers to inquiries will be posted on the Town’s e-

Procurement Portal. Bidders may also click “Follow” on this RFP to receive an email notification when answers are posted. It is the responsibility of the bidder to check the website for answers to inquiries.

When applicable, state bids will be considered for this service.

The Purchasing Authority reserves the right to waive any informality or reject any and all bids. In addition to the bid specifications, all bids are subject to the terms, provisions and conditions of the

Manchester Charter, Code of Ordinances, and Purchasing Guidelines. By bidding on the proposed purchase, the bidder agrees to such terms, provisions and conditions.

An Equal Opportunity/Affirmative Action Employer

2.2. BID OPENING INFORMATION

Proposals must be received by the date and time indicated in the bid documents.

2.3. RULES AND REGULATIONS FOR COMPETITIVE BIDDING

These rules and regulations have been adopted by the Board of Directors of the Town of Manchester pursuant to Section 5-22 of the Town Charter. They are standard for all competitive bidding proposals issued by the Town of Manchester, Connecticut for contracts of all types where labor, materials, and https://procurement.opengov.com/portal/townofmanchester https://procurement.opengov.com/portal/townofmanchester https://procurement.opengov.com/portal/townofmanchester necessary equipment to complete work is to be furnished to the Town, where the Town is to purchase supplies, materials, and equipment, where the Town is to sell surplus materials and equipment, or where the Town is to sell real estate. These rules and regulations shall be binding upon all prospective bidders and the Town of Manchester.

2.4. GENERAL RULES

1. The Director of Purchasing may delete or modify any of the instructions to bidders for a particular proposal, indicating such change in the appropriate section of the proposal documents. The Director of

Purchasing may insert special instructions in any special contracts which are subject to competitive bidding.

2. The proposal is signed by the bidder with full knowledge of, and agreement with, the general specifications, conditions, and requirements of this proposal.

3. The town has transitioned to electronic bidding. Vendors should submit solicitation responses electronically via the Town of Manchester Procurement Portal. Vendors will be asked to register and should do so prior to submitting proposal documents.

4.This proposal and any addenda will be issued on the Town of Manchester website bidding portal. It shall be the responsibility of the bidder to download this information. THE TOWN OF MANCHESTER

WILL NOT MAIL A SEPARATE HARD COPY OF ADDENDUM TO BIDDERS. Failure of any bidder to receive any such addendum or interpretation shall not relieve such bidder from any obligation under his bid as submitted. All addenda so issued shall become part of the Contract Documents.

5. Bid prices may not be withdrawn by bidder for 90 days after bid opening.

6. Proposals received later than the time and date specified will not be considered. Amendments to, or withdrawals of proposals received later than the time and date set for submission deadline will not be considered.

7. All deliveries of commodities or services hereunder shall comply in every respect with all applicable laws of the Federal Government and/or the State of Connecticut.

8. Purchases made by the Town of Manchester are exempt from payment of Federal Excise Taxes and the Connecticut Sales Tax and such taxes must not be included in bid prices. Federal Excise Tax exemption certificates, if requested, will be furnished.

9. The Bidder, where applicable, shall insert/include the price per stated unit and extend a total price for each item. In the event there is a discrepancy between the unit price and the extension, the unit price will govern. The total cost shall be the sum of the extended prices.

10. Bidders shall, where applicable, submit terms for payment in spaces provided in the proposal form, showing the amount of cash discount which shall apply to bid prices when paid within the stated number of days in the proposal.

11. All inquiries shall be submitted within the time limitations specified in the bid documents and shall be requested via the online portal Q&A. All information given by the Town other than through the

OpenGov Portal shall be informal and shall not be binding upon the Town nor shall it furnish a basis for legal action by any bidder or prospective bidder against the Town.

11A. The Town reserves the right to reject any and all proposals, to waive technical defects, and to make such awards including accepting a proposal, although not the lowest cost, as it deems in its sole discretion to be in the best interest of the Town. The Town reserves the right to reject any proposal if the bidder, any officer of the bidder, or any other company owned in whole or in part by any officer(s) of the bidder, is delinquent in the payment of any taxes or fees owed to the Town. The Town reserves the right to require a disclosure statement from the bidder listing the name(s) of all officers of the company.

11B. In the event the Town determines that a contractor is delinquent in any payment due the Town, then the Town may offset the delinquent amount due to the Town against the sums owed the contractor.

12. The Town of Manchester may make such investigation as deemed necessary to determine the ability of the bidder to discharge a contract. The bidder shall furnish the Town with all such information and data as may be required for that purpose. The Town reserves the right to reject any proposal if the bidder fails to satisfactorily convince the Town that he is properly qualified by experience and facilities to carry out the obligations of the contract and to satisfactorily complete the work called for herein, or if the proposal is conditional in nature.

13. Except where otherwise provided, a contract between the Town and a successful bidder shall consist of the Request for Proposal, Specifications, Plans, Proposal, and Acceptance by the Town and these

Rules and Regulations. Acceptance by the Town may be by purchase order for the portion of the work awarded to a contractor.

14. All Requests for Proposal shall be publicly advertised in a newspaper having a general circulation within the Town of Manchester, Connecticut.

15. The Request for Proposal shall be made available on the Town of Manchester Purchasing Web Site via the OpenGov Portal.

16. Any act or acts of misrepresentation or collusion shall be a basis for disqualification of any proposal or proposals submitted by such persons guilty of said misrepresentation of collusion. In the event that the Town enters into a contract with any bidder who is guilty of misrepresentation or collusion and such conduct is discovered after the execution of said contract, the Town may cancel said contract without incurring liability, penalty, or damages.

17. In the event that any bidder wishes to protest the potential award of a proposal, the bidder must make it’s protest in writing, identify the protesting party, the bid number, title and shall include a factual summary of the basis of the protest including any documents that shall be considered and request a conference with respect thereto. Said protest must be received in the Town of Manchester Purchasing

Office, within FIVE (5) business days after the award decision.

18. A conference with respect to said protest shall be scheduled by the Director of Purchasing and shall be attended by the Director or their designee and such other persons as the Director and the General

Manager shall require attend. The subject matter of said conference shall be limited to the reasons for the protest specified in the written request for said conference. Said conference shall also include a discussion of all possibilities for a resolution of dispute. The Town shall make a decision in writing within three (3) business days after said conference and notify protesting bidder.

19. In the event that any protesting bidder wishes to take legal action against the Town, they must first fully comply with all of these Rules and Regulations, including those which have been changed by the

Director of Purchasing pursuant to paragraph 1 herein.

20.Except for special instructions inserted in special contracts by the Director of Purchasing pursuant to paragraph 1 herein, in the event of any conflicts between these Rules and Regulations and the terms and conditions of any document these Rules and Regulations shall prevail.

21. All Awards shall be made by the Purchasing Department designee.

22. The Town of Manchester is an equal opportunity employer and requires an affirmative action policy for all of its Contractors and Vendors as a condition of doing business with the Town, as per Federal

Order 11246. By signing the Proposal form for this proposal, all vendors and contractors agree to this condition of doing business with the Town, and should the Town choose to audit their compliance, the vendor agrees to cooperate fully.

2.5. Important Instructions for Electronic Submittal

Bidders shall create a FREE account with Open Gov Procurement by signing up at https://secure.opengov.com/portal/townofmanchester. Once you have completed account registration, browse back to this page, https://procurement.opengov.com/portal/townofmanchester and click on

"Submit Response", and follow the instructions to submit the electronic bid.

2.6. Instructions to Bidders

In accordance with the provisions of the Town Charter, sealed proposals will be received through the

OpenGov Portal, not later than the date and time set forth above, for furnishing the commodities and/or services listed herein. Proposals must be executed in accordance with and subject to instructions and specifications contained herein.

3. STANDARD INSTRUCTIONS TO BIDDERS

TOWN OF MANCHESTER

PURCHASING DEPARTMENT

494 MAIN STREET

P.O. BOX 191

MANCHESTER, CONNECTICUT 06045-0191

3.1. Overview:

The Town of Manchester (Town) desires to engage a contractor to provide the services in support of the

Install a Monorail Fall Protection System at Globe Hollow Water Treatment Facility.

Incorporated as part of the RFP are the #Attachments, #Scope of Work . The Project includes, but is not limited to, Invitation to RFQ/RFP, Instructions to Bidders, Supplementary Instructions to Bidders, RFQ/RFP Form, Standard Form of Agreement Between Owner and Contractor , General Conditions of the Contract for Construction , and Supplementary General Conditions of the Contract for Construction.

3.2. Description of Project:

FURNISH AND INSTALL A MONORAIL FALL PROTECTION SYSTEM AT GLOBE HOLLOW WATER

TREATMENT FACILITY

3.3. Services Required:

The Town is seeking to engage a contractor to provide Install a Monorail Fall Protection System at Globe

Hollow Water Treatment Facility The contract will be a modified AIA 101-2017 Standard Form of

Agreement Between Owner and Contractor Stipulated Sum and a modified AIA A201-2017 General

Conditions of the Contract for Construction. The Town reserves the right to modify or amend these documents in such manner as is acceptable to the Town.

The Contractor to be engaged in this Project shall become part of the Project team working with the

Town representatives, the NO VALUE.

The Town reserves the right to award the contract to the contractor deemed to be in the best interests of the Town for the Project after review of the submissions received, not based solely on cost or any other specific factors.

The duties and responsibilities of the contractor will include the outlined scope and will include but not be limited to the following:

No

3.4. Minimum Requirements:

Firms shall provide appropriate credentials and documentation as follows:

Minimum of 10 years experience in fall protection https://procurement.opengov.com/portal/townofmanchester/projects/29150?section=undefined https://procurement.opengov.com/portal/townofmanchester/projects/29150?section=undefined

3.5. Qualification Requirements:

1. Firm Description – Provide a description and brief history of the firm. Name firms, location of principal and branch offices; length of time in business; and firm ownership structure.

2. Related Experience – Please provide a list of all projects at secure facilities (police stations, prisons, defense contractors, etc.) currently in progress and completed over the last five years. The description should at a minimum provide the project name, location, year of completion, type of contract, renovation cost, size, owner name and reference with telephone number.

3. Organization and Staffing – Provide an organization chart for staff proposed for this project which clearly identifies your proposed management staff for the project (Project Executive, Project Manager, Project Superintendent, etc.). Also include detailed resumes for each person identified.

4. Typical Project Approach – Provide description of services your firm will utilize during each phase of the project to ensure the project is completed on schedule and within budget.

5. Litigation/Arbitration – List information on (a) any involvement in litigation or arbitration with municipal clients; and (b) all clients that have terminated your services prior to completion of any project within the past ten (10) years. Explain circumstances that led to it and describe the resolution.

6. Bonding – Include the name of your bonding company and agent as well as a letter for the bonding company stating your bonding limits, available capacity and A.M. Best Rating.

7. Insurance – Contractor/ Vendor shall agree to maintain in force at all times during the contract the following minimum coverages and shall name the Town of Manchester as Additional Insured on a primary and non-contributory basis to all policies except Workers Compensation.

8. Additional Information – Any other information that, in the judgment of the General Contractor, may allow the Town to make a fair assessment of the experience and abilities of the Contractor.

4. PROJECT DETAILS

4.1. Install a Monorail Fall Protection System at Globe Hollow Water Treatment Facility

The Town of Manchester Water & Sewer Department (MWDS) has identified the need to install a plain and trussed monorail fall protection system with gantry cranes on the sedimentation basins at the Globe

Hollow Water Treatment Plant. We are seeking proposals from qualified Contractors for fabrication, delivery, installation, and training on a Fall Protection System design provided in this proposal.

Engineered fall protection systems such as DBI/Sala or MSA will be given priority.

4.2. System Description

a. Fuss & O’Neill Section 112429.19 – Plain and Trussed Monorail Fall Protection System.

b. Fuss & O'Neill Section 412213.13 – Gantry Cranes

c. Fuss & O'Neill Drawings – S-001, S-101, S-501

4.3. Sub-system requirements DBH Sala or equivalent

a. Provide 5 Harness (size to be determined).

b. Self Retracting Lifelines (SRL’s) with connecting components.

c. Harnesses and vertical lifelines (VLLs) used with the system shall comply with ANSI Z359.1.

d. Connecting components (carabiners and snap hooks) used with the system shall comply with ANSI

Z359.12.

e. Self-retracting lifelines (SRLs) used with the system shall comply with ANSI Z359.14.

4.4. Installation

a. Installation of the system shall be performed by a system registered installer, in accordance with approved shop drawings and manufacturer's instructions.

b. The Fall Protection System shall be installed under the direction of manufacturer's authorized trained personnel and under the supervision of a Qualified Person.

c. Install anchorages and fasteners in accordance with manufacturer's recommendations to obtain the allowable working loads published in the product literature and in accordance with this specification.

d. Fall protection system shall not be loaded or stressed until all materials and fasteners are properly installed and ready for service.

e. Where bolting is used for fastening, no fewer than three threads are to be exposed and the nut is to be positively locked using a thread- locking fluid or the double nutting technique.

f. Dissimilar materials with greater than 0.15V shall be separated by a faying surface.

g. Install all instructional signs as required by OSHA fall protection regulations

4.5. Field Quality Control

a. After the Fall Protection System is installed, Contractor shall have an approved authorized, qualified individual inspect and operate the system and shall make all final adjustments for proper operation.

4.6. Adjustment and Final Inspections

a. Contractor shall verify that all manufactured units have been installed in accordance with specifications and details and will function as intended. Adjust any items where necessary to ensure proper operation.

b. Provide a complete drawing set with any revisions to the design or layout of the fall protection system during installation

4.7. Operator Training

a. Provide a minimum of 2 hours of operator training covering OSHA 1926.503(a) and field practical after system has been installed. Training will be done at the installation site, for the users of the new system.

Contractor will submit a copy of the proposed training components for review prior to the awarding of the contract.

b. Provide certification of training specific to each individual trained.

4.8. Maintenance, Inspection and Testing

a. Provide manufacturer maintenance, inspection and testing instructions.

b. Provide documentation that is consistent with applicable OSHA and ANSI standards

5. STANDARD INSURANCE AND INDEMNIFICATION REQMNTS

5.1. GENERAL CONDITIONS:

Within ten (10) business days of the award or notice, or prior to the start of work, whichever comes first, the contractor/insured will provide, pay for, and maintain in full force and affect the insurance outlined here for coverage’s at not less than the prescribed minimum limits of liability. Such coverage is to remain in force during the life of the contract and for such additional time as may be required, and will cover the contractor/ insured’s activities, those of any and all subcontractors, or anyone directly or indirectly employed by any of them, or by anyone for whose acts any of them may be liable. Any failure to comply with reporting requirements and provisions of the policies shall not affect coverage provided to Town, its officers, officials, agents or employees.

A. Certificates of Insurance: The contractor/insured will give the owner a certificate of insurance completed by a duly authorized representative of their insurer certifying that at least the minimum coverage’s required here are in effect and specifying that the liability coverage’s are written on an occurrence form and that the coverage’s will not be canceled, non-renewed, or materially changed by endorsement or through issuance of other policy(ies) of insurance without sixty (60) days advance written notice to the General Services Department. Failure of the owner to demand such certificate or other evidence of full compliance with these insurance requirements or failure of the owner to identify a deficiency from evidence provided will not be construed as a waiver of the contractor/insured’s obligation to maintain such insurance. Any failure to comply with reporting requirements and provisions of the policies shall not affect coverage provided to Town, its officers, officials, agents or employees.

B. Insurer Qualification: All insurance will be provided through companies authorized to do business in the State of Connecticut and considered acceptable by the owner.

C. Additional Insured: The policy or policies providing insurance as required, with the exception of professional liability and workers’ compensation, will defend and include the owner and owner’s architects, directors, officers, representatives, agents, and employees as additional insureds on a primary and noncontributory basis for work performed under or incidental to this contract.

D. Retroactive Date and Extended Reporting Period: Coverage, whether written on a claims made or occurrence basis, shall be maintained without interruption from the date of commencement of the

Work until date of final payment and then extended for an additional three (3) years from date of final payment.

If any insurance required here is to be issued or renewed on a Claims Made form as opposed to an

Occurrence form, the retroactive Date for coverage will be no later than the commencement date of the project. The Claims Made form will have an Extended Reporting Period of three years from the date of project completion. All Claims made policies cancelled or non-renewed and not replaced by a subsequent claims made policy will have an Extended Reporting period of three years from the date of cancellation or non-renewal.

E. Subcontractors’ Insurance: The contractor/insured will require each subcontractor hired by and/or employed by contractor/insured to purchase and maintain insurance of the types specified below. When requested by the owner, the contractor/insured will furnish copies of certificates of insurance evidencing coverage for each subcontractor.

F. Waiver of Subrogation: The contractor/subcontractor will purchase required insurance policies that shall be endorsed with a waiver of subrogation and all rights of recovery in favor of the Town, its officers, officials, agents and employees. The contractor/insured will require of subcontractors, by appropriate written agreements, similar waivers each in favor of all parties enumerated in this section.

G. Hold Harmless: The contractor/insured shall defend, indemnify and hold harmless the owner, officers, officials, agents and employees, and if applicable, the engineer and their agents and employees from and against all claims, damages, losses and expenses, including attorney’s fees of counsel selected by the owner, arising out of or resulting from the performance of the work and /or the supplying of materials, provided that any such claim, damage, loss or expense (a) is attributable to bodily injury, sickness, disease or death, or to injury to or destruction of tangible property including the loss of use resulting therefrom, and (b) is caused in whole or in part by any negligent act or omission of the contractor/ insured, any subcontractor, anyone directly or indirectly employed by any of them or anyone for whose acts any of them may be liable, regardless of whether or not they are caused in part by a party indemnified hereunder.

5.2. INSURANCE LIMITS AND COVERAGE:

A. To the extent applicable, the amounts and types of insurance will conform to the minimum terms, conditions and coverage’s of Insurance Services Office (ISO) policies, forms, and endorsements.

B. If the contractor/insured has self-insured retention’s or deductibles under any of the following minimum required coverage’s, the contractor/insured must identify on the certificate of insurance the nature and amount of such self-insured retention’s or deductibles and provide satisfactory evidence of financial responsibility for such obligations. All self-insured retention’s or deductibles will be the contractor/ insured’s sole responsibility.

C. Workers’ Compensation Insurance: With respect to all operations the Contractor performs and all those performed for it by subcontractors, the Contractor shall carry, and require each subcontractor to carry, Workers’ Compensation insurance as required by the laws of the State of Connecticut.

Employer’s Liability insurance shall be provided in amounts not less than:

• $500,000 per accident for bodily injury by accident;

• $500,000 policy limit by disease; and

• $500,000 per employee for bodily injury by disease

D. Commercial General Liability Insurance: With respect to the operations the Contractor performs and also those performed for it by subcontractors, the Contractor shall carry, and require each subcontractor to carry, Commercial General Liability insurance, including Contractual Liability, Products and Completed Operations, Broad Form Property Damage and Independent Contractors. See chart below for applicable minimum coverage amounts.

If the Contract amount is between 0 and $2,000,000:

• The Minimum Single Occurrence Amount required is $1,000,000 and the Minimum Annual

Aggregate Amount is $2,000,000

If the Contract amount is between $2,000,000 and $10,000,000:

• The Minimum Single Occurrence Amount required is $2,000,000 and the Minimum Annual

Aggregate Amount is $4,000,000

If the Contract amount is > $10,000,000:

• The Minimum Single Occurrence Amount is $4,000,000 and the Minimum Annual Aggregate

Amount is $8,000,000

Notes:

• If underground work is to be undertaken, each policy shall have coverage for and exclusions removed for “Explosion, Collapse and Underground” (“XCU”).

• Should blasting be required, all necessary permits for the use of explosives shall be obtained by the contractor/insured or insured from the Fire Marshall.

E. Automobile Liability Insurance: The Contractor shall obtain automobile liability insurance covering the operation of all motor vehicles, including those hired or borrowed, that are used in connection with the

Project for all damages arising out of bodily injury to or death of all persons and/or injury to or destruction of property; in any one accident or occurrence. This policy shall not be subject to an annual aggregate limitation. See chart above for applicable minimum coverage amounts.

F. Owner’s and Contractor’s Protective Liability Insurance for and in the Name of the Town and/or State:

With respect to the Contractor’s Project operations and also those of its subcontractors, the Contractor shall carry, for and on behalf of the Town and/or State for each accident or occurrence resulting in damages from bodily injury to or death of persons and/or injury to or destruction of property. See chart below for applicable minimum coverage amounts.

If the Contract amount is between 0 and $2,000,000:

• The Minimum Single Occurrence Amount required is $1,000,000 and the Minimum Annual

Aggregate Amount is $2,000,000

If the Contract amount is between $2,000,000 and $50,000,000:

• The Minimum Single Occurrence Amount required is $2,000,000 and the Minimum Annual

Aggregate Amount is $4,000,000

If the Contract amount is > $50,000,000:

• The Minimum Single Occurrence Amount is $4,000,000 and the Minimum Annual Aggregate

Amount is $8,000,000

G. Excess Coverage: Contractor shall purchase and maintain excess or umbrella liability insurance with a limit of not less than $5,000,000, covering all lines of insurance required by this contract.

6. LIVING WAGE ORDINANCE

6.1. Living Wage Ordinance

This contract is subject to provisions of the Town of Manchester Living Wage Ordinance. A summary description of the ordinance and the certification form is attached. Bidders are asked to indicate on the attached Certification Form if your firm would be considered a covered employer. The Certification Form shall be returned to the Town with the proposal.

6.2. Summary Description for Vendors Regarding Manchester’s Living Wage Ordinance

Effective February 1, 2010, the Town of Manchester adopted a living wage ordinance. This Summary

Description is designed to provide any vendor bidding on a Town of Manchester contract with the key provisions of that ordinance. It does not contain the full ordinance.

LIVING WAGE REQUIREMENT:

The ordinance requires that companies awarded service contracts by the Town of Manchester exceeding $25,000 in any one fiscal year pay their Eligible Employees a living wage. Companies considered Covered Employers subject to this requirement are defined below. The Town of Manchester has determined that the contract resulting from this bid or Request for Proposals will be subject to the ordinance if the total contract value is $25,000 or more in any one fiscal year.

The living wage is currently calculated to be $15.34 per hour for employees that are provided comprehensive health care benefits, or $23.35 per hour for employees that are not provided comprehensive health care benefits.

The living wage and health benefit requirements are adjusted annually each July, effective July 1, 2010.

Companies will be required to pay the applicable living wage rate in effect during the term of their contracts.

COVERED EMPLOYERS AND EXEMPTIONS:

The ordinance requires that Covered Employers pay the living wage rate. Certain employers are excluded from paying the living wage rate. They are as follows:

Non-profit organizations as defined by the ordinance, and

Entities that employ less than 25 eligible employees.

ELIGIBLE EMPLOYEES:

Eligible employees are all permanent, full time employees of the company (defined as a normal work week of at least 30 hours), working in the State of Connecticut, not just those working on the Town contract. The following are not considered eligible employees for the purposes of the living wage requirement:

Employees with a normal work week of less than 30 hours.

Seasonal or temporary employees.

Employees under the age of 18.

Employees hired as part of a school-to-work program.

Students who serves in a work-study program or as an intern.

Trainees participating for not more than six months in a training program.

Employees enrolled in a governmentally funded vocational rehabilitation program.

Volunteers working without pay.

Employees exempted under Section 14(c) of the Fair Labor Standards Act due to disabilities.

Any person whose wage rate is subject to a federal or State of Connecticut statute or regulation mandating a prevailing wage rate.

EMPLOYER OBLIGATIONS:

Covered Employers are required to do the following pursuant to the ordinance.

Certify with the submission of their bid or proposal a) that they will pay the required living wage to eligible employees if awarded a contract, or b) that they are exempt from requirements of the ordinance, Upon award, covered employers shall provide the Town a sworn affidavit affirming that all eligible employees of the covered employer working in the State of Connecticut are receiving the living wage and health benefits required by this ordinance.

This sworn affidavit shall be provided thereafter on an annual basis within 30 days of a request being made by the Town if the duration of the contract exceeds one (1) year.

Notify their employees of their rights under the Living Wage Ordinance by posting a copy of the ordinance and other materials prepared by the Town of Manchester in locations where employees will see them.

Make best efforts to attempt to hire residents of the Town of Manchester for all new positions which result from a service contract subject to the ordinance.

PROHIBITED PRACTICES:

Covered Employers cannot decrease non-wage benefits (such as insurance, vacation, or pension) as a means of complying with the living wage requirements.

Covered Employers cannot retaliate or discriminate against any employee for making a complaint against the covered employer regarding compliance with living wage requirements.

ENFORCEMENT:

The Town may enforce the provisions of this ordinance by the imposition of fines, suspension of contract or declaring the Covered Employer ineligible for future contracts.

WAIVERS:

The ordinance provides for the waiver of certain requirements in the ordinance. However, no waivers will be considered until the bidding process has been completed and a contract has been awarded.

Requests for waivers must be made by the Covered Employer, in writing, to the General Manager. The

General Manager shall submit the waiver request to the Board of Directors, which shall have the sole discretion as to whether it is granted.

The above is intended to be a summary of the requirements of the living wage ordinance as they affect covered employers and is provided for informational purposes only. Employers should read the entire

Living Wage Ordinance. It can be found online at www.townofmanchester.org on the left side of the page. Click on Document Center, scroll to General Services and click on Living Wage Ordinance.

7. EVALUATION CRITERIA

The Town will evaluate all proposals deemed responsive to this request by a committee selected by the

Town of Manchester. Proposals will be evaluated by the Town based on the following criteria:

• Quality, clarity and responsiveness of proposal.

• Functional and Technical capabilities.

• Installation, implementation and training plan.

• Demonstrated performance of proposed system elsewhere, system maintenance, updating and ongoing technical support and references.

• Cost of software/and support.

If deemed necessary by the committee, the Town of Manchester reserves the right to shortlist the proposals received and arrange for interviews/ oral presentations to the committee as part of the selection process. Discussions, requests for additional information and negotiations may take place with the short list vendors to ensure clarification and to obtain a system that meets the requirements of this

RFP.

The Town of Manchester shall select the responsible and responsive Proposal which is determined by the Town to be the best suited, most advantageous, and provides the greatest overall benefit to the

Town on the basis of the criteria and evaluation factors included in this Request for Proposal. Cost shall be only one factor in the award decision. The Town expressly reserves the right to negotiate with the selected vendor prior to an award of any contract pursuant to this Request for Proposal.

No. Evaluation Criteria Scoring Method Weight (Points)

1. Safety Information

1 Contractor shall submit evidence of the following:

a. Recordable injury rate for last three years

b. Lost workday incidence rate for the last three years

c. Experience Modification Rate (EMR)

d. Safety citations, violations, or warnings from regulatory agencies over the last five years

e. Safety training for all site employees, including specific courses and requirements based on work to be performed during the project.

Points Based 40 (40% of Total)

2. Quality and thoroughness of the proposal, and scope of services offered.

Points Based 30

(30% of Total)

3. Contractor Experience

1 Contractor shall submit evidence of the following:

a. Minimum ten (10) years’ experience designing fall protection systems.

b. Minimum five (5) years documented experience in the fabrication of such components similar to that required for this project.

c. Minimum five (5) years documented experience in the installation of such components.

d. Ability to perform regular inspections and maintenance service on such systems.

e. Minimum of two (2) systems installed in the previous 12 months.

Points Based 10 (10% of Total)

4. References and Recognition/Awards. Points Based 10 (10% of Total)

5. Price / Cost Points Based 10 (10% of Total)

8. VENDOR SUBMISSIONS

8.1. Proposal Requirements*

Please confirm that you have read and agreed with the entire RFP and related attachments (if any) including

A. General Conditions

B. Special Provisions and Specifications

☐ Yes

☐ No

*Response required

8.2. Firm Description*

Provide a description and brief history of the firm. Name of firm, location of principal and branch offices;

length of time in business; and firm ownership structure.

*Response required

8.3. Related Experience*

Please provide a list of all projects at secure facilities (police stations, prisons, defense contractors, etc.)

currently in progress and completed over the last five years. The description should at a minimum provide the project name, location, year of completion, type of contract, renovation cost, size, owner name and reference with telephone number.

*Response required

8.4. Organization and Staffing*

Provide an organization chart for staff proposed for this project which clearly identifies your proposed management staff for the project (Project Executive, Project Manager, Project Superintendent, etc.).

Also include detailed resumes for each person identified.

*Response required

8.5. Typical Project Approach*

Provide description of services your firm will utilize during each phase of the project to ensure the project is completed on schedule and within budget.

*Response required

8.6. Litigation/Arbitration*

List information on (a) any involvement in litigation or arbitration with municipal clients; and (b) all clients that have terminated your services prior to completion of any project within the past ten (10) years. Explain circumstances that led to it and describe the resolution.

*Response required

8.7. Insurance*

Contractor/ Vendor shall agree to maintain in force at all times during the contract the following minimum coverages and shall name the Town of Manchester as Additional Insured on a primary and non-contributory basis to all policies except Workers Compensation.

☐ Please confirm

*Response required

8.8. Separate Cost Proposal*

Confirm that your fee proposal is not attached in your Proposal and is attached separately here.

*Response required

8.9. Addenda *

This bid and any addenda will be issued on the Town of Manchester website bidding portal. It shall be the responsibility of the bidder to download this information. THE TOWN OF MANCHESTER WILL NOT

MAIL A SEPARATE HARD COPY OF ADDENDUM TO BIDDERS. Failure of any bidder to receive any such addendum or interpretation shall not relieve such bidder from any obligation under his bid as submitted. All addenda so issued shall become part of the Contract Documents.

☐ Please confirm

*Response required