IFQ_6200_AJC1022_IFQ_ATT_2_v1.pdf

Exhibit 1

ColbertA Highlight

Exhibit 1.1

Exhibit 2

Exhibit 2.1

POLELINE HARDWARE

Part #: 8262

Category: 5/8" DIAMETER B CABLE SUSPENSION BOLT

5/8'' X 14'' B CABLE SUSPENSION BOLT HOT DIP GALVANIZED

Used to secure two cable suspension clamps at opposite sides of utility pole.

Collars are forged instead of welded for extra strength.

Bolt provided with cone point at each end to ease starting.

Hot dip galvanized to meet ASTM Specification F2329.

Manufacturers mark (ABI) and tensile load designation mark (i.e.10M, 16M, 25M) appear on the unthreaded section of each bolt.

ABI marking is registered with the U.

S Patent Office per the Fastner Insignia Act.

Minimum tensile strength: 13,550 lbf.

Recommended torque value: 73 ft lb.Unthreaded section is 4".

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

35 1 52

Exhibit 3 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

AERIAL DROP HARDWARE

Part #: 4040

D CABLE LASHING CLAMP MECHANICALLY GALVANIZED

Used in aerial construction to secure terminating lashing wire or ground wire to a strand.

Tensile strength of the jaws exceeds 50,000 psi.

Terminal ends of stud are staked to prevent disassembly during shipping and installation.

Attaches to strand ranging in size from 1/4"(6.6M) to 7/16"(16M).

The jaws are rolled and stamped from annealed 1018 Steel.

The stud of the D Cable Lashing Clamp is formed from Grade 5 Steel.

Exhibit 4 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=AERIAL%20DROP%20HARDWARE

All components of D Cable Lashing Clamps are mechanically galvanized to meet ASTM Specification B695.

The Stainless Steel Lashing Clamp is comprised of a stud, two washers, and two nuts manufactured in 304 Stainless Steel, along with a set of mechanically galvanized steel jaws.

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

50 4 30

Part #: 8283

Category: 5/8" DIAMETER A CABLE SUSPENSION BOLT

5/8'' X 14'' A CABLE SUSPENSION BOLT HOT DIP GALVANIZED

Used to secure cable suspension clamps and other poleline brackets and clamps.

Each square head bolt is supplied with two attached regULar square nuts.

Bolt provided with cone point to ease starting.

Bolt head marking (ABI) appears on head of each bolt and is registered with the U.S.Patent Office per the Fastener Insignia Act.

Tensile load designation mark (i.e.10M, 16M, 25M) also appears on head of each bolt.

A minimum of six inches of thread per bolt.

Hot dip galvanized to meet ASTM Specification F2329.

Minimum tensile strength: 13,550 lbf.

Recommended torque value: 73 ft lb.Minimum thread length is 6".

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

40 1 54

Exhibit 5 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Part #: 8284

Category: 5/8" DIAMETER A CABLE SUSPENSION BOLT

5/8'' X 16'' A CABLE SUSPENSION BOLT HOT DIP GALVANIZED

Used to secure cable suspension clamps and other poleline brackets and clamps.

Each square head bolt is supplied with two attached regULar square nuts.

Bolt provided with cone point to ease starting.

Bolt head marking (ABI) appears on head of each bolt and is registered with the U.S.Patent Office per the Fastener Insignia Act.

Tensile load designation mark (i.e.10M, 16M, 25M) also appears on head of each bolt.

A minimum of six inches of thread per bolt.

Hot dip galvanized to meet ASTM Specification F2329.

Minimum tensile strength: 13,550 lbf.

Recommended torque value: 73 ft lb.Minimum thread length is 6".

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

30 1 45

Exhibit 6 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Part #: 8285

Category: 5/8" DIAMETER A CABLE SUSPENSION BOLT

5/8'' X 18'' A CABLE SUSPENSION BOLT HOT DIP GALVANIZED

Used to secure cable suspension clamps and other poleline brackets and clamps.

Each square head bolt is supplied with two attached regULar square nuts.

Bolt provided with cone point to ease starting.

Bolt head marking (ABI) appears on head of each bolt and is registered with the U.S.Patent Office per the Fastener Insignia Act.

Tensile load designation mark (i.e.10M, 16M, 25M) also appears on head of each bolt.

A minimum of six inches of thread per bolt.

Hot dip galvanized to meet ASTM Specification F2329.

Minimum tensile strength: 13,550 lbf.

Recommended torque value: 73 ft lb.Minimum thread length is 6".

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

30 1 48

Exhibit 7 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Part #: 8263

Category: 5/8" DIAMETER B CABLE SUSPENSION BOLT

5/8'' X 16'' B CABLE SUSPENSION BOLT HOT DIP GALVANIZED

Used to secure two cable suspension clamps at opposite sides of utility pole.

Collars are forged instead of welded for extra strength.

Bolt provided with cone point at each end to ease starting.

Hot dip galvanized to meet ASTM Specification F2329.

Manufacturers mark (ABI) and tensile load designation mark (i.e.10M, 16M, 25M) appear on the unthreaded section of each bolt.

ABI marking is registered with the U.

S Patent Office per the Fastner Insignia Act.

Minimum tensile strength: 13,550 lbf.

Recommended torque value: 73 ft lb.Unthreaded section is 4".

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

30 1 49

Exhibit 8 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Exhibit 9

Part #: 8206

5/8''-11 REGULAR SQUARE NUT HOT DIP GALVANIZED

Used to fasten attachments to machine bolts, carriage bolts, and insULator pins.

Manufactured from Grade 2 Steel.

Hot dip galvanized to meet ASTM Specification A153.

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

100 1 10

Exhibit 10 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

CHANCE

CONFIDENTIAL: THIS DRAWING AND ITS

CONTENTS ARE CONFIDENTIAL AND THE

EXCLUSIVE PROPERTY OF HUBBELL POWER

SYSTEMS. NO PUBLICATION, DISTRIBUTION, OR

COPIES MAY BE MADE WITHOUT THE WRITTEN

CONSENT OF HUBBELL POWER SYSTEMS. HUBBELL

POWER SYSTEMS UNPUBLISHED ALL RIGHTS

RESERVED UNDER THE COPYRIGHT LAWS.

TITLE

SIZE

DWG NO.CAT / PART / ASSY NO.

REV

DO NOT SCALE

THIS DRAWING

DRN BY DATE SHEET

B

5/8"

OVALEYE BOLT

HUBBELL POWER SYSTEMS, INC.

SEE TABLE G

11/25/20

TOLIVER

SA29956

POWER SYSTEMS, INC.

2.0

1.5

0.55

2.0 "L"

"T"

0.56

5/8-11UNC-2A THREADS

MANUFACTURER'S IDENTIFICATION

CATALOG NUMBER "L" "T"

29956 6 4

29958 8 4

29959 9 4

29960 10 6

29962 12 6

29964 14 6

29966 16 6

29968 18 6

29970 20 6

29972 22 6

29974 24 6

2997026 26 6

2997028 28 6

2997030 30 6

- NOTES -

1. MATERIAL: LOW CARBON STEEL.

2. FINISH: HOT DIP GALVANIZE PER ASTM A153.

3. STRENGTH AND DIMENSIONS PER ANSI/IEEE C135.4

INCLUDING THE FOLLOWING:

- MINIMUM TENSILE STRENGTH OF 13,550 LBS

- OVALEYE BOLT TO MEET THE 180° BEND TEST.

Exhibit 11

AB910040

Part #: AB910040

1/4'' GUY DEADEND GRIP GALFAN COATED- YELLOW

Provides a means for attaching Guy Wire Hooks, Anchor Rods, and Eye Nuts.

Holding Strength is greater than ratings of strand accommodated.

Rated at 100% of guy strand RBS for EHS, HS, Siemens-Martin, Common and Utility Grades.

Standard Packaging Information:

Exhibit 12 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

50 1 36

Automatic Splice, Full Tension, for 5/16"

EHS, AW

By Anderson

Catalog # GLS5041

Automatic Splice, Full Tension, for 5/16" Alumoweld, HS, Common, Utilities, Siemens-Martin guy grades

Features

Individually bagged to seal out dirt before use

GLS Automatic splices will hold a minimum of 90% of the guy wire breaking strength

Specifications

UL Listed No

Conductor

Conductor Diameter -

Maximum

0.324 in

Conductor Diameter - Minimum 0.300 in

Dimensions

Width 1.220 in

Weight 0.776 lb.

Height 1.220 in

Length 9.400 in

Dimensions 9.400 in x 1.220 in x 1.220 in

General

Material - Gripping Unit Plated Steel

Material Aluminum Alloy

Steel

Material type Standard

UPC 096359389484

Color Code None

Logistics

Pallet Quantity 2400

Product Assets

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

AN-GLS5041-SPEC-EN | REV 1/2026

Exhibit 13 https://www.hubbell.com/hubbell/en/products/p/151405 https://www.hubbell.com/hubbell/en/products/p/151405 https://www.hubbell.com/hubbell/en/products/p/151405 https://www.hubbell.com/hubbell/en/products/p/151405 https://www.hubbell.com/hubbell/en/products/p/151405 https://hubbellcdn.com/catalogfull/CA05127E_Distribution%20Connector_EN_2023.pdf https://www.hubbell.com/hubbell/en

BANDING

Part #: 2402

1-1/2'' X 5-1/4'' ALUMINUM MOUNTING PLATE WITH 5/8 X 3'' HEX BOLT HOT DIP GALVANIZED

Provides a mount for various attachments including Cable Suspension Clamps.

Extruded from high strength Aluminum.

Standard Packaging Information:

Exhibit 14 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=BANDING

25 1 22

Exhibit 15 https://pgc.com/ https://ab.pgc.com/

Part #: 4080

C CABLE CLAMP HOT DIP GALVANIZED

Used to secure jacketed strand or self-supporting cable to telephone poles.

Each clamp is comprised of two steel plates having an oval hole in the center and a serpentine groove.

Clamp is equipped with two track bolts and two regULar square nuts.

Manufactured from Ductile Iron.

May be used on in-line poles and at corners with a pULl of 25° or less.

Installed without slitting the web of the cable.

The center hole is provided for use with a 5/8" diameter cable suspension bolt.

All components are hot dip galvanized to meet ASTM Specification A153.

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

16 1 39

Exhibit 15.1 https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Part #: 5084

5/8'' C GUY HOOK HOT DIP GALVANIZED

Designed to accept a loop of strand, a strand grip, or a Strand Dead-end in down guy applications.

Recessed bolt hole to accept head of Square Head Machine Bolts.

Features a wide inner shoULder and broad heel pad to resist embedding.

Features "chisel point" spurs to resist down slotting in pole.

Cannot be used in "back to back" guying on pole.

Forged from Ductile Iron.

Exhibit 16 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Hot dip galvanized to meet ASTM Specification A153.

Has an ULtimate strength load of 13,000 LBS at 45°; PULl.

Standard Packaging Information:

25 1 46

11555

Part #: 11555

Category: CURVED WASHER FOR 5/8" BOLT

CURVED WASHER 2-1/2'' X 2-1/2'' X 11/16'' HOLE X 3/16'' THICK HOT DIP GALVANIZED

Used under the heads of bolts, nuts, and other threaded products to provide a broader bearing surface and increase the compression grip of the tightened nut.

Bent at a 4-1/2" radius to fit the contour of poles.

Stamped from AISI 1018 Steel.

Hot dip galvanized to meet ASTM Specification A153.

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

50 4 62

Exhibit 17 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

11500

Part #: 11500

Category: SQUARE WASHER FOR 5/8" BOLT

3/16'' X 2-1/4'' SQUARE WASHER FOR 5/8'' BOLT HOT DIP GALVANIZED

Used under the head of bolts and nuts to provide a broader bearing surface and to increase the compression of a tightened nut.

Stamped from AISI 1018 Steel.

Hot dip galvanized to meet ASTM Specification A153.

Exhibit 18 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Standard Packaging Information:

100 2 54

Part #: 1060

1/4'' WIRE ROPE THIMBLE HOT DIP GALVANIZED

Used in guying applications to form an oval wire eye for securing to eye-bolts and guy rods.

Eye Width is 7/8".

Eye Length is 1-1/2".

Manufactured from AISI 1018 Steel.

Hot dip galvanized to meet ASTM Specification A153.

Exhibit 19 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

100 1 7

Part #: 5080

B CABLE SUSPENSION CLAMP HOT DIP GALVANIZED

Used to attach strand to straight line poles.

Accepts 1/4" (6.6M) to 7/16" (16M) strand.

Consists of two plates, and two 1/2"-13 track bolts with attached square nuts.

Plates are 1-11/16" wide and 5-3/4" long.

Center hole accepts 5/8" Thru Bolts Hot dip galvanized to meet ASTM Specification A153.

Exhibit 20 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

25 1 43

Part #: 4870

15'' FIBERGLASS EXTENSION ARM

Standoff Brackets are used in aerial construction to provide a set distance from the Utility Poles for mounting Suspension Clamps.

Standoff Brackets are provided with a fixed 5/8"-11 x 2-5/8" Stud that includes a mating Square Nut, Lock Washer and Square Washer.

Both End Fitting and Pole Fitting are Casted from Ductile Iron.

Reinforced Epoxy Fiberglass Rod diameter is 1-1/2".

Mounting holes accommodate 5/8" Thru-Bolts and are spaced six inches apArt.Minimum ULtimate Vertical Load: 1,800 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

Minimum ULtimate Longitudinal Load: 1,200 LBS(recommended maximum working load is 50% of minimum ULtimate rating).

Exhibit 21 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Minimal ULtimate Transverse Load: 1,500 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

2 1 11

Part #: 4874

24'' FIBERGLASS EXTENSION ARM

Standoff Brackets are used in aerial construction to provide a set distance from the Utility Poles for mounting Suspension Clamps.

Standoff Brackets are provided with a fixed 5/8"-11 x 2-5/8" Stud that includes a mating Square Nut, Lock Washer and Square Washer.

Both End Fitting and Pole Fitting are Casted from Ductile Iron.

Reinforced Epoxy Fiberglass Rod diameter is 1-1/2".

Mounting holes accomodate 5/8" Thru-Bolts and are spaced six inches apArt.Minimum ULtimate Vertical Load: 1,100 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

Minimum ULtimate Longitudinal Load: 700 LBS(recommended maximum working load is 50% of minimum ULtimate rating).

Exhibit 22 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

Minimal ULtimate Transverse Load: 1,500 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

2 1 14

Part #: 4876

36'' FIBERGLASS EXTENSION ARM

Standoff Brackets are used in aerial construction to provide a set distance from the Utility Poles for mounting Suspension Clamps.

Standoff Brackets are provided with a fixed 5/8"-11 x 2-5/8" Stud that includes a mating Square Nut, Lock Washer and Square Washer.

Both End Fitting and Pole Fitting are Casted from Ductile Iron.

Reinforced Epoxy Fiberglass Rod diameter is 1-1/2".

Mounting holes accommodate 5/8" Thru-Bolts and are spaced six inches apArt.Minimum ULtimate Vertical Load: 900 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

Minimum ULtimate Longitudinal Load: 500 LBS(recommended maximum working load is 50% of minimum ULtimate rating).

Minimal ULtimate Transverse Load: 1,500 LBS (recommended maximum working load is 50% of minimum ULtimate rating).

Standard Packaging Information:

Pkg Qty Pkg Per Carton Carton Weight

2 1 17

Exhibit 23 https://pgc.com/ https://ab.pgc.com/ https://ab.pgc.com/collections/vendors?q=POLELINE%20HARDWARE

FOSC-450

©2026 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: March 30, 2026

Base Product

FOSC® 450 Fiber Optic Splice Closure

The FOSC-450 is a single-ended, environmentally sealed enclosure for fiber management in the outside plant network. FOSC-450 gel splice closures have the same splice capacity as FOSC-400 closures and feature the same reliable and easy-to-use dome-to-base clamping system. The major difference between the closures is that the

FOSC-450’s cable sealing terminations use gel-sealing technology instead of heat shrink.

The FOSC-450 features a single wrap-around gel seal with four or six cable ports. The single seal slides easily into the closure’s base for rapid, secure installation. Gel-seal cable terminations automatically adjust to cable size and shape, and require no special tools or accessories to install. It is easy to remove cables, and gel seal is completely re-usable.

The FOSC-450 closure is available in 3 different sizes. According to the application, many configurations are possible.

FOSC 450 A4 closure The FOSC 450 A4 closure is the smallest in the FOSC 450 series having fourlarge round ports. It is intended for low fiber-count cable splices and “tap-off” splices. The FOSC 450 A4 closure comes ready to store expressed loose buffer tubes. An optical slack storage basket is available for expressed stranded fiber and ribbon fiber.

FOSC 450 BS closures The FOSC 450 BS closures are identical except for their end cable port configuration. In addition to a large oval port for the main distribution cable, the BS closure has six large round ports for branch cable splices. The FOSC 450 closure cable sealing system provides a great deal of flexibility.

Exhibit 24

©2026 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: March 30, 2026

FOSC 450 D6 closures The FOSC 450 D6 closure is the largest in the FOSC 450 series having six large round ports.

The splice capacity is 288 single mechanical, 768 single fusion or 1152 mass-fusion (12) fibers. Ribbon fiber can be stored directly on the trays or in the versatile slack basket that also holds expressed or uncut loose buffer tubes.

Key features of the FOSC 450 closures:

Single-ended design Available in 3 sizes Base and dome sealed with clamp and O-ring system 4 or 6 round cable ports provided in a wrap-around block with pre-installed gel profile for cable sealing. This block can be opened and closed repeatedly withoutremoving or replacing the gel. With the use of special kits, multiple cables per port can be installed

FOSC splice trays hinged for access to any splice without disturbing fibers in other trays Compatible with most common cable types: e.g. loose tube, central core, slotted core, ribbon fiber Uncut or expressed loose tubes can be stored in storage baskets Closure can be used in aerial, pedestal and underground (up to 5 meters waterhead) environments

Product Classification

Product Type Single-ended, round fiber closure

Product Brand FOSC®

Product Series FOSC 450

General Specifications

Cable Entry Drop Port Style Round

Cable Entry Main Port Style Round

Cable Sealing Type Compressed gel

Closure Sealing Type Dome-to-base clamp with O-ring

Closure Style Single-ended

Color Black

Mounting Pole | Strand | Wall

Splicing Type, Supported Mass fusion | Single fusion

Exhibit 24.1

©2026 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: March 30, 2026

Dimension Drawing

Port Configuration

Splicing Configuration

Exhibit 24.2

©2026 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: March 30, 2026

Ordering Tree

Material Specifications

Material Type Impact-resistant polymer

Exhibit 24.3

©2026 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: March 30, 2026

Environmental Specifications

Environmental Space Below ground | Buried

Qualification Standards IEC 61300, 5 m waterhead | Telcordia GR-771-CORE

Regulatory Compliance/Certifications

Agency Classification

ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system

Exhibit 24.4

ALUMINUM RIGID CONDUIT Generic Listing (980030)

ARC

TRADE

SIZE METRIC NOMINAL OUTSIDE

DIAMETER

NOMINAL INSIDE

DIAMETER

NOMINAL WALL

THICKNESS

APPROXIMATE

WEIGHT PER

100 PIECES

IN MM IN MM IN MM LB KG

1/2 16 .840 21.34 .632 16.05 .104 2.64 28 12.7

3/4 21 1.050 26.67 .836 21.23 .107 2.72 37 17.0

1 27 1.315 33.40 1.063 27.00 .125 3.20 55 24.7

1-1/4 35 1.660 42.16 1.394 35.41 .133 3.38 72 32.5

1-1/2 41 1.9 48.26 1.624 41.25 .138 3.51 89 40.2

2 53 2.375 60.33 2.083 52.91 .146 3.71 119 53.8

2-1/2 63 2.875 73.03 2.489 63.22 .193 4.90 188 85.0

3 78 3.5 88.90 3.090 78.49 .205 5.21 246 111.7

3-1/2 91 4.0 101.60 3.570 90.68 .215 5.46 296 134.1

4 103 4.5 114.30 4.050 102.87 .225 5.72 350 158.9

5 129 5.563 141.30 5.073 128.85 .245 6.22 479 217.2

6 155 6.625 168.28 6.093 154.76 .266 6.76 635 287.8

Information contained herein is furnished for convenience and reference. Every effort is made to ensure accuracy, but there is no guarantee and publisher assumes no liability for any act resulting from the use hereof. © 2016 Trade Service, A Trimble Company

Exhibit 25

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

Exhibit 26

Blackburn® W™ Aluminum Service Wedge Clamps

Deadend self-supporting drop wire.

WEDGE CLAMPS

Overhead Connectors and Covers

Drop Wire May Be Cut to Exact Length Adjustments in drop wire sag are easily made. This also saves the conductor.

Can Be Attached to Bare Neutral at Any Point in the Span

Place them where you most need them

Versatile Use Flexible and rigid bails grip ACSR, AAC and AAAC conductors.

Benefits/DescriptionsFeatures

* W40 series clamps rated 850 lb. ultimate tension for 1/0 ACSR, AL or AAAC.

† For extremely corrosive areas.

NOTE: Catalogue numbers with “FC” suffix have a flexible bail.

CAT. NO. Description Conductor Range Dimensions (in.) Typical Tensile Values Colour

CodeACSR AL AAAC D L Conductor Value (lb.)

W62-1

W-1 Series aluminum wedge and slider

#2–#6 #1 str.–#6 sol. #2–#6 2-3/8 12

2 (6/1) ACSR 1,200 Orange W62-1 FC flex. 17-1/2

W20-1 1/0–#4 2/0 str.–#2 sol. 1/0–#4

2-3/8 12-1/2 1/0 (6/1) ACSR 1,800 Blue

W20-1 FC flex. 18-1/2

W40-1* 4/0–2/0 4/0 str.–2/0 sol. 4/0–2/0

2-3/8 12-3/4 4/0 (6/1) ACSR 1,900 Red

W40-1 FC* flex. 18-1/2

W62-1 B†

W-1B Series iridited aluminum wedge and slider

2–#6 #1 str.–#6 sol. 2–#6 2-3/8 12

2 (6/1) ACSR 1,200 Orange W62-1 BFC† flex. 17-1/2

W20-1 B† 1/0–#4 2/0 str.–#2 sol. 1/0–#4

2-3/8 12-1/2 1/0 (6/1) ACSR 1,800 Blue

W20-1 BFC† flex. 18-1/2

W40-1 B*† 4/0–2/0 4/0 str.–2/0 sol. 4/0–2/0

2-3/8 12-3/4 4/0 (6/1) ACSR 1,900 Red

W40-1 BFC*† flex. 18-1/2

Blackburn® W™ Aluminum Service Wedge Clamps

Exhibit 27 & 28

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

ColbertA Highlight

Blackburn® W™ Stainless Steel Wedge Clamp

The wedge clamp that stands up to corrosion.

WEDGE CLAMPS

Ov er he ad

C on ne ct or s an d Co ve rs

Stainless Steel Wedge and Slider Rigid bail grips copper neutral conductors.

Drop Wire May Be Cut to Exact Length Adjustments in drop wire sag are easily made. This also saves the conductor.

Can Be Attached to Bare Neutral at Any Point in the Span

Place them where you most need them.

Benefits/DescriptionsFeatures

L

D

CAT. NO.

Conductor Range Dimension (in.) Typical Tensile Values Colour

CodeStranded Solid D L Conductor Value (lb.)

W62D #2–#6 #1–#6 2-3/8 12 #2–#7 str. AAC 1,300 Orange

Blackburn® W™ Stainless Steel Wedge Clamp

Exhibit 29

2-1/2in SQUARE CURVED WASHER for 5/8in BOLT SIZE, 11/16in HOLE

By Chance

Catalog # PS6822

Washers protect the crushing of wood fibers under loading conditions.

Features

Square curved washer, 2-1/2" square x 3/16" thick

11/16" diameter hole for 5/8" diameter bolt

Manufactured in compliance with NEMA PH-10

Galvanized per ASTM A-153 or ASTM B695

Specifications

Buy America(n) Qualified BABA Compliant (All status valid till December 2026)

Dimensions

Dimension - Hole Size inch 11/16 in

Size 2-1/2 in X 2-1/2 in X 3/16 in

Bolt Size 5/8 in

Distance From Pole N/A

Width 0.187 in

Weight 0.27 lb.

Height 2.500 in

Length 2.500 in

Dimensions 2.500 in x 0.187 in x 2.500 in

General

Type Washer

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359073857

Logistics

Pallet Quantity 7200

Product Assets

Catalog [English]

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-PS6822-SPEC-EN | REV 4/2026

Exhibit 30 https://www.hubbell.com/hubbell/en/products/p/307271 https://www.hubbell.com/hubbell/en/products/p/307271 https://www.hubbell.com/hubbell/en/products/p/307271 https://www.hubbell.com/hubbell/en/products/p/307271 https://www.hubbell.com/hubbell/en/products/p/307271 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://hubbellcdn.com/catalogfull/CENT-CP-CAT-EN-01974.pdf https://www.hubbell.com/hubbell/en

2in SQUARE FLAT WASHER for 5/8in BOLT SIZE, 11/16in HOLE

By Chance

Catalog # 6812

Square washers distribute the load and protect against crushing of wood fibers. They provide a smooth surface against the nut, which makes loosening less likely.

Features

Square flat washer, 2" square x 1/8"

11/16" diameter hole for 5/8" diameter bolt

Manufactured in compliance with NEMA PH-10

Galvanized per ASTM A-153 or ASTM B695

RUS listed, d - Washers, flat

Specifications

Industry Standard(s) NEMA PH10

Dimensions

Dimension - Hole Size inch 11/16 in

Size 2 in X 2 in X 1/8 in

Bolt Size 5/8 in

Distance From Pole N/A

Width 1.875 in

Weight 0.12 lb.

Height 0.126 in

Length 1.875 in

Dimensions 1.875 in x 1.875 in x 0.126 in

General

Type Washer

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359073758

Logistics

Pallet Quantity 14400

Product Assets

Catalog [English]

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-6812-SPEC-EN | REV 1/2026

Exhibit 31 https://www.hubbell.com/hubbell/en/products/p/307296 https://www.hubbell.com/hubbell/en/products/p/307296 https://www.hubbell.com/hubbell/en/products/p/307296 https://www.hubbell.com/hubbell/en/products/p/307296 https://www.hubbell.com/hubbell/en/products/p/307296 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://hubbellcdn.com/catalogfull/CENT-CP-CAT-EN-01974.pdf https://www.hubbell.com/hubbell/en

EYENUT, STANDARD, 5/8"

By Chance

Catalog # 6502

Standard eyenut that fits 5/8" diameter bolts. Most commonly used for deadending, back-guying, and attaching pole head guys on the threaded ends of crossarm bolts.

Features

Tensile strength rating is 13,550 lbs

Meets the requirements of ANSI C135.5

Specifications

Industry Standard(s) ANSI C135.5

RUS Listed Reference aa - Nut, eye

Dimensions

Width 2.500 in

Weight 0.66 lb.

Height 1.375 in

Length 3.250 in

Dimensions 3.250 in x 2.500 in x 1.375 in

General

Type Eyenuts

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359073369

Logistics

Pallet Quantity 2400

Product Assets

Catalog [English]

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-6502-SPEC-EN | REV 1/2026

Exhibit 32 https://www.hubbell.com/hubbell/en/products/p/306578 https://www.hubbell.com/hubbell/en/products/p/306578 https://www.hubbell.com/hubbell/en/products/p/306578 https://www.hubbell.com/hubbell/en/products/p/306578 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://hubbellcdn.com/catalogfull/CENT-CP-CAT-EN-01974.pdf https://www.hubbell.com/hubbell/en

GUY WIRE THIMBLE, 3/8in SIZE

By Chance

Catalog # 6593

Open end of thimble slips over ovaleye anchor rods or bolts to protect strand from abrupt, strand-weakening kinks.

Features

Grooved to fit 3/8" dia. strand

Galvanized per ASTM A-153

Dimensions

Distance From Pole N/A

Weight 0.09 lb.

Height 2.5 in

Length 0.59 in

General

Type Thimble

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359073581

Logistics

Pallet Quantity 16000

Product Assets

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-6593-SPEC-EN | REV 3/2026

Exhibit 33 https://www.hubbell.com/hubbell/en/products/p/307125 https://www.hubbell.com/hubbell/en/products/p/307125 https://www.hubbell.com/hubbell/en/products/p/307125 https://www.hubbell.com/hubbell/en/products/p/307125 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://www.hubbell.com/hubbell/en

CHANCE

CONFIDENTIAL: THIS DRAWING AND ITS

CONTENTS ARE CONFIDENTIAL AND THE

EXCLUSIVE PROPERTY OF HUBBELL POWER

SYSTEMS. NO PUBLICATION, DISTRIBUTION, OR

COPIES MAY BE MADE WITHOUT THE WRITTEN

CONSENT OF HUBBELL POWER SYSTEMS. HUBBELL

POWER SYSTEMS UNPUBLISHED ALL RIGHTS

RESERVED UNDER THE COPYRIGHT LAWS.

TITLE

SIZE DWG NO.CAT / PART / ASSY NO. REV

DO NOT SCALE

THIS DRAWING

DRN BY DATE SHEET

C

GUY HOOK

HUBBELL POWER SYSTEMS, INC.

SEE CHART C

1 OF 1 06/04/2021URBECK

SAGH5

POWER SYSTEMS, INC.

3.6

4.75

Ø "A" n0.56

2.5

2.6

1.8

-NOTES-

1. MAT'L: DUCTILE IRON PER ASTM A536 (LATEST REVISION).

2. HOT DIP GALVANIZE PER ASTM A153 (LATEST REVISION).

3. SUFFIX "N" INDICATES NO TEETH AND IS FOR USE ON STEEL

OR CONCRETE POLES.

NOTE-3

CATALOG

NUMBER "A" NOTES

GH5 0.69 --

GH5N 0.69 NOTE-3

GH6 0.81 --

GH6N 0.81 NOTE-3

Exhibit 34

REGULAR SQUARE NUT FOR 5/8in

THREAD BOLTS

By Chance

Catalog # 55084P

Regular square nut for 5/8" diameter bolt with 5/8-11-UNC threads. Hot dip galvanized per ASTM A-153. Manufactured in compliance with ANSI C135.1.

Features

Hot dip galvanized per ASTM A-153

Manufactured in compliance with ANSI C135.1.

Specifications

Industry Standard(s) ANSI C135.1

Dimensions

Distance From Pole N/A

Width 1.000 in

Weight 0.1 lb.

Height 0.500 in

Length 1.000 in

Dimensions 1.000 in x 1.000 in x 0.500 in

General

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359072676

Logistics

Pallet Quantity 20000

Product Assets

Catalog [English]

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-55084P-SPEC-EN | REV 1/2026

Exhibit 35 https://www.hubbell.com/hubbell/en/products/p/306782 https://www.hubbell.com/hubbell/en/products/p/306782 https://www.hubbell.com/hubbell/en/products/p/306782 https://www.hubbell.com/hubbell/en/products/p/306782 https://www.hubbell.com/hubbell/en/products/p/306782 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://hubbellcdn.com/catalogfull/CENT-CP-CAT-EN-01974.pdf https://www.hubbell.com/hubbell/en

INSULATOR, SPOOL, ANSI 53-2 CLASS,

POLYMER, BLACK

By Chance

Catalog # C9091032P

A superior direct replacement for porcelain ANSI 53-2 spool insulators in identical installations. Molded from specially blended UV stable polymers for high compressive strength.

Features

Lightweight: 4.4 oz. (vs. porcelain 1 lb. 3 oz.) Rugged: Won't chip, crack or break like porcelain.

Specifications

Industry Standard(s) ANSI 53-2

Buy America(n) Qualified TAA Compliant (All status valid till December 2026)

Dimensions

Distance From Pole N/A

Width 3.077 in

Weight 0.26 lb.

Height 3.077 in

Length 2.971 in

Dimensions 2.971 in x 3.077 in x 3.077 in

Force Related

Tensile Strength 3000 lb.

General

Material Polymer Blend

UPC 096359368779

Logistics

Pallet Quantity 2000

Product Assets

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-C9091032P-SPEC-EN | REV 4/2026

Exhibit 36 https://www.hubbell.com/hubbell/en/products/p/306732 https://www.hubbell.com/hubbell/en/products/p/306732 https://www.hubbell.com/hubbell/en/products/p/306732 https://www.hubbell.com/hubbell/en/products/p/306732 https://www.hubbell.com/hubbell/en/products/p/306732 https://hubbellcdn.com/catalogfull/5-53_Supp1-19.pdf https://www.hubbell.com/hubbell/en

SPOOL INSULATOR SECONDARY CLEVIS,

SAGGER STYLE

By Chance

Catalog # C2070072

Clevis bracket for spool insulators used in secondary deadend applications. For use with ANSI Class 53-2 spool insulators. No cotter pin required; after insulator is installed, the metal tab is bent downward, securing the clevis pin in place. Replacement component: clevis pin - 450033P.

Features

11/16" x 13/16" dia. mounting hole

5/8" dia. clevis pin

Hot dip galvanized per ASTM A-153

Dimensions

Distance From Pole N/A

Width 4.625 in

Weight 1.49 lb.

Height 3.875 in

Length 5.500 in

Dimensions 5.500 in x 4.625 in x 3.875 in

General

Type Insulated Secondary Clevis

Material Steel

Coating Galvanized, ASTM A-153

UPC 096359014362

Style Sagger

Logistics

Pallet Quantity 600

Product Assets

Catalog [English]

A Hubbell brand © 2026 Hubbell Incorporated. All rights reserved

CH-C2070072-SPEC-EN | REV 1/2026

Exhibit 37 https://www.hubbell.com/hubbell/en/products/p/306527 https://www.hubbell.com/hubbell/en/products/p/306527 https://www.hubbell.com/hubbell/en/products/p/306527 https://www.hubbell.com/hubbell/en/products/p/306527 https://www.hubbell.com/hubbell/en/products/p/306527 https://hubbellcdn.com/catalogfull/05-PLH.pdf https://www.hubbell.com/hubbell/en

Locking Heads T&B Catalog Number:

TYD-LH

UPC Number: 78621071339 Status: Active Description:

Cable Tie Deltec 25 Heads Only Features

Perfect for coaxial, fiber optic and all other commu-nication and electrical conducting cables.

Strap and body are weatherable acetal, offering su-perior resistance to sunlight, moisture and salt envi-ronments.

Locking device is marine-grade corrosion-resistant copper alloy.

Application

Ideal solution for bundling in harsh outdoor environ-ments.

General

Material Weather-Resistant Acetel

Color Black

Specifications

Temperature Rating -30°F to 150°F

Tooling

Application Tools WT3D

Packaging

T&B Order Multiple 25

T&B Inner Pack 25

Package in Units 125

Package Type Regular

T&B Sold in UOM Each

T&B Weight Per UOM 0.96 lbs. per 100

Application Support

Overview Available on Website

Material Selection Guide Available on Website

Notes

The recommended maximum continuous static loading for the Deltec® straps is 20 lbs. Per strap.

For best results suggested spacing is 15 inch-

es. It is the responsibility of the user to determine whether or not their application meets our recom-mendation.

Certifications

RoHS Compliance Yes

For further technical assistance, please contact us...

Thomas & Betts - USA 8155 T&B Blvd.

Memphis, TN 38125

T&B Technical Support

MS 3B-50

8155 T&B Blvd.

Hours: 7AM - 6PM CDT Monday-Friday Phone: (888) 862-3289

Exhibit 38 www.tnb.com Memphis, TN 38125 Fax: (901) 252-1321 Email:techsupport@tnb.com

Exhibit 39

Compact for Low Fiber Count Splicing Applications

COYOTE® PUP CLOSURE

Exhibit 40

World Headquarters 660 Beta Drive Cleveland, Ohio 44143

Mailing Address:

P.O. Box 91129 Cleveland, Ohio 44101

Telephone: 440.461.5200 Fax: 440.442.8816 Web Site: www.preformed.com E-mail: inquiries@preformed.com

© 2009 Preformed Line Products Printed in U.S.A.

CO-SS-1011-4

05.09.2M

COYOTE® PUP Closure Refinement of the breed The COYOTE PUP Closure offers a perfect choice for low fiber count distribution applications involving butt and in-line installations. The compact size and rugged design allow the closure to be applied in below grade, aerial and buried installations. Supported by a full line of COYOTE accessories, this closure can grow along with your network.

Key Features

COYOTE PUP Closure Kits

Catalog Number Description

8006622 Closure Kit for Buffer Tube, includes (1) 3 section 6 port end plate, (1) blank end plate, and buffer tube organizer (ribbon)

8006621 Closure Kit for Unitube, includes (1) 3 section 6 port end plate, (1) blank end plate, transport tube kit and ribbon organizer

8006661

RUS listed Closure Kit for Buffer Tube, includes

(1) 3 section 6 port end plate, (1) blank end plate and Buffer Tube Organizer, includes (1) 3 section 6 port end plate, (1) blank end plate and (2) RUS listed shield connectors

800011398 COYOTE PUP for Copper, includes torque bars

800011399 COYOTE PUP for Copper, includes (1) 3 section 4 port end plate, (1) blank end plate and torque bars

800010515 Closure Kit for Buffer Tube, includes (1) 3 section 4 port end plate, (1) blank end plate and buffer tube organizer

Splice Tray/Closure Capacities

Splice Tray

Depth

Description Splices per Tray Capacity per Tray

Trays per

Closure

Closure Capacity

Low Profile Single Fusion 12 6 72

Standard Single Fusion

& Single Mechanical

12 4 48

Ribbon Mass Fusion 72 2 144

Fiber Management System for Buffer Tube Cable.

COYOTE PUP Closure

Compact 12-Fiber Splice Tray

Accessory Kits

80805795 Shell Kit 6.0" x 17.0"

80805771 Buffer Tube Storage Compartment

80805775 Unitube Storage (Transition) Compartment

80805105 6 Port End Plate Kit, includes (1) end plate assembly, (1) full set of plugs, and LOCK- TAPE™ sealing material

80805739 4 Port End Plate Kit, includes (1) end plate assembly, (1) full set of plugs, and LOCK- TAPE sealing material

80805260 Blank end plate kit

8003371

Future Cable Port Kit, includes Future Cable Port for 7/8" port, plug and clamps for installation of future cable port during initial assembly

8003291

Future Cable installation Kit, includes LOCK-TAPE Sealant, bead sealant and L-bracket for preparation of future cable up to .86" in diameter

8003289 Future Cable Port/Cable Installation Kit, includes 8003291

80806037 3/4" Plug Kit (contains 2 plugs)

80806180 7/8" Plug Kit (contains 2 plugs)

80806038 1" Plug Kit (contains 2 plugs)

80806181 1-1/4" Plug Kit (contains 2 plugs)

80805293 Transport Tube Kit (contains 6 tubes)

8003280 Transport Tube Kit, used to transition fibers from top section of end plate to the transition compartment

8003418 Heat Shield for COYOTE PUP Closure

Splice Tray Kits

80807701 12 Count Low Profile tray with rigid plastic splice block

80806033 12 Count Standard tray with soft elastomer splice block

80807114 72 Count Ribbon tray with soft elastomer splice block

Installation Materials

80805238 C-Cement, 1-oz tube

80805925 LOCK-TAPE Sealant 1"W x 15"L roll

Catalog Number Description

Mounting Hardware Kits

8003325 Aerial hanger bracket

8003279 Manhole support bracket

8003372 Pole/wall mount bracket (vertical)

Exhibit 40.1

Catalog# Description

Deltec® Cable Support System

CSS-100 Cable Strap with head, 10.0” long

CSS-135 Cable Strap with head, 13.5” long

CSS-160 Cable Strap with head, 16.0” long

CSS-270 Cable Strap with head, 27.0” long

CSS-50R 50 foot Reel of Strap

CSS-5K 5 Reels Cable Strap, 150 locking heads

CSS-10K 10 Reels Cable Strap, 300 locking heads

CSS-B Base

CSS-H Hanger

CSS-LH Locking Head

TCP-360 Modular Stackable Cable Spacer

CSS-360 Modular Stackable Spacer for Fiber and Coax Cable

WT3D Installation/Cutting Tool

TC5359 Mounting Base for Masonry

Deltec Kit CSS-5K, CSS-10K

Please ask your Thomas & Betts representative for a complete catalog of quality Thomas & Betts products or visit us at www.tnb.com. For customer service, call 1-800-685-9452. For technical questions, call 1-888-862-3289.

Thomas & Betts Corporation Communications Products Group Tel: 800-920-0328 • 901-252-5000 Fax: 800-283-6756 • 901-252-1389

© 2006 Thomas & Betts Corporation. All rights reserved.

Data Sheet # CDS-DELTEC

Locking heads and 50 ft reels of cable strap available in bulk packs of 5 or 10 reel kits

CSS-LH

Acetal plastic head with integral marine grade silicon bronze locking device

TCP-360

Stackable 1/2” spacer for use with telecom cables.

Can be rotated 90º to accommodate large or multiple cables.

CSS-360

Stackable 1/2” spacer designed with smooth body surface to prevent deformation of coaxial and fiber optic cables.

WT3D

Use for tightening and cutting Deltec cable support straps. Safe and easy to use, cuts strap flush with locking head

- no sharp edges!

TC5359

Nylon mounting base for masonry and brick surfaces, requires 3/8” pre-drilled hole.

CSS-100, CSS-135, CSS-160

and CSS-270 Pre-cut cable straps ranging from 10” to 27” long with locking head installed.

CSS-50R

50 ft reel of cable strap- can be cut to any desired length.

CSS-B

Zinc-plated steel base for vertical cable or wire runs.

CSS-H

Zinc-plated steel hanger for horizontal cable or wire runs.

Ordering Information

Exhibit 41

Deltec® Cable Support System

Provides a strong, long-life and cost saving method of securing communication cables

The Deltec® Cable Support System is a user-friendly product de-signed to provide fast, effective fastening of communications cables to messenger strand. It is equally well suited for copper conductor cable, coaxial cable, fiber optic cable and inner duct in aerial ap-plications.

The Deltec® System answers your aerial cable needs with innova-tive design and state of the art materials. UV, weather resistant acetal plastic cable straps, marine grade locking devices and plated steel hanger accessories combine to provide a system that can meet your specific needs.

Deltec® cable strap is available in standard lengths of 10 to 13.5, 16 and 27 inches as well as in convenient 50 foot reels to reduce waste and allow custom sizing by the technician in the field. Addi-tional “standard” lengths can be established for applications where higher volumes prevail.

• � Proven years of service

• No sharp edges - Craft-Friendly! Cable Friendly!

• Ease of installation - one wrap, no re-threading of strap

• Lowers installation costs

• High tensile strength

• Total flexibility in strap length

Strap and Body

Locking Device

Installation Range

• -30º F to 150º F

Minimum Tensile Strength

• 250 Pounds

Outdoor Life

Continuous Load

• 20 Pounds

Please ask your Thomas & Betts representative for a complete catalog of quality Thomas & Betts products or visit us at www.tnb.com. For customer service, call 1-800-685-9452. For technical questions, call 1-888-862-3289.

Thomas & Betts Corporation Communications Products Group Tel: 800-920-0328 • 901-252-5000 Fax: 800-283-6756 • 901-252-1389

© 2006 Thomas & Betts Corporation. All rights reserved.

Data Sheet # CDS-DELTEC

TCP-360 provides desired spacing between messenger and telecom cables in 1/2” increments

CSS-360 spacer can be used with fiber optic or coaxial cable in single or multiple cable applications

CSS-H zinc plated steel hanger for horizontal runs, installs easily on any surface

CSS-B zinc plated steel base provides additional strength for vertical cable runs

Exhibit 41.1 www.panduit .com

Dimensions: CFAPPBL1: 19.00"W x 1.72"H x 0.44"D (482.60mm x 43.7mm x 11.2mm) CFAPPBL1A: 19.00"W x 1.72"H x 4.16"D (482.60mm x 43.7mm x 105.5mm) CFAPPBL2: 19.00"W x 3.47"H x 0.44"D (482.60mm x 88.1mm x 11.2mm) CFAPPBL2A: 19.00"W x 3.47"H x 4.16"D (482.60mm x 88.1mm x 105.6mm) FMT1: 19.00"W x 1.72"H x 11.16"D (482.60mm x 43.7mm x 283.4mm) FMT1A: 19.00"W x 1.72"H x 11.16"D (482.60mm x 43.7mm x 283.4mm) FMT2: 19.00"W x 3.47"H x 11.16"D (482.60mm x 88.1mm x 283.4mm) FMT2A: 19.00"W x 3.47"H x 11.16"D (482.60mm x 88.1mm x 283.4mm)

Mounting: Integral mounting flange for installation in 19" wide EIA-310 racks

Accessories: Mounting hardware and accessory kit with labels included k e y f e a t u r e s a n d b e n e f i t s a p p l i c a t i o n s t e c h n i c a l i n f o r m a t i o n s p e c i f i c a t i o n s The rack mount fiber tray and fiber adapter patch panels shall house, organize, manage and protect fiber optic cable, splices, and connectors. Available in both flat and angled versions, patch panels shall accommodate all Panduit pre-terminated MTP* cassettes, fiber adapter panels (FAP), fiber mount panels (FMP), associated trunk cables, connectors, patch cords, and shall include integral cable management. Fiber trays shall be constructed of steel material. Steel cover shall be removable for cabling and connector access during installation. Enclosure shall have multiple knockouts for a variety of trunk cable entry points.

Works with all Panduit ® Provides versatility and flexibility with a fully modular Opticom ® Fiber Optic solution for a variety of pre-terminated installations, FAP Cassettes and Fiber and field termination, and splicing installations. Works with Adapter Panels all Panduit LC, SC, ST, MT-RJ and MTP* fiber adapter panels and cassettes

Provides higher patch field Modular design mounts up to four Opticom ® Cassettes or density in fewer rack units FAP’s per RU and up to three Opticom ® Cassettes per saving valuable space RU for the angled fiber optic trays

Angled design Angled design allows cable to flow to each side of the rack: patch cords can be routed directly into vertical cable managers

Fiber optic splice module Can fusion splice up to 96 fibers per RU in a single enclosure with one-to-one splice-to-patching ratio

Side and rear cable entry Provides installer with several options to route cable within the tray

Patch panel mounting Hardware provided to allow patch panel to be pre-assembled before mounting to rack

Opticom ® Rack Mount Fiber Trays and Fiber Adapter Patch Panels provide a flexible and modular system for managing fiber termination, connections, and patching for all applications and offer the industry’s highest patch field density and fiber counts for all fiber termination methods. Angled fiber optic patch panels facilitate proper bend radius of each patch cord as it is routed directly into a vertical cable manager, eliminating the need for horizontal cable managers. The high capacity, high-density solution maximizes rack space utilization and reduces floor space requirements for lower overall system costs.

Opticom ® Fiber Optic Patch Panels and Trays

Opticom ® Rack Mount Fiber Adapter Patch Panels 1 RU for 4 FAP’s or cassettes: CFAPPBL1 1 RU for 4 FAP’s or cassettes, angled: CFAPPBL1A 2 RU for 8 FAP’s or cassettes: CFAPPBL2 2 RU for 8 FAP’s or cassettes, angled: CFAPPBL2A Opticom ® Rack Mount Fiber Trays For use with CFAPPBL1: FMT1 For use with CFAPPBL1A: FMT1A For use with CFAPPBL2: FMT2 For use with CFAPPBL2A: FMT2A

Opticom ® Fiber Adapter Panels 12 duplex LC, 10Gig ™: FAP12WAQDLCZ 6 duplex LC, 10Gig ™: FAP6WAQDLCZ 12 duplex LC: FAP12WEIDLC 6 duplex LC: FAP6WEIDLC 6duplex SC, 10Gig ™: FAP6WAQDSCZ 3 duplex SC, 10Gig ™: FAP3WAQDSCZ 6 duplex SC: FAP6WEIDSC 3 duplex SC: FAP3WEIDSC 6 simplex ST: FAP6WST

6 MTP*: FAPH6W12BLMTP

OptiCore ® Patch Cords 12 fiber MTP* to MTP*: F^12D5-5M**Y Duplex LC to LC: F^E10-10M**Y Duplex SC to SC: F^D3-3M**Y Duplex SC to LC: F^D3-10M**Y

Splice Modules Splice module (fusion): FOSMF Splice module (mechanical): FOSMM

Tools and Accessories Patch cord removal tool: PCRT1

^Substitute for fiber types:

X = (OM3/OM4 – 10Gig ™ 50/125µm) 5 = (OM2 – 62.5/125µm) 6 = (OM1 – 62.5/125µm) 9 = (OS1 – 9/125µm) *MTP is a registered trademark of US Conec Ltd.

**Substitute for length in meters: 1, 2, 3, 5 and 10 are standard lengths.

Contact Panduit Customer Service for other available lengths.

SPECIFICATION SHEETExhibit 42

F i b e r C a p a c i t i e s

©2009 Panduit Corp.

ALL RIGHTS RESERVED.

WW-FBSP39

9/2009

12 duplex LC adapters

Fiber Adapter Panel Type

FMT1

(holds up to 4 FAPs)

Enclosure and Fiber count

FMT2A

(holds up to 8 FAPs)

8 duplex LC adapters

6 duplex LC adapters

6 duplex SC adapters

32 64

3 duplex SC adapters 24 48

FMT2

(holds up to 8 FAPs)

FMT1A

(holds up to 4 FAPs)

1.72 [43.7]

Opticom ® Fiber Optic Patch Panels and Trays

For a copy of Panduit product warranties, log on to www.panduit.com/warranty

Contact Customer Service by email: cs@panduit.com or by phone: 800-777-3300 and reference FBSP39

Visit us at www.panduit.com For more information

Dimensions are in inches. [Dimensions in brackets are metric].

4 duplex SC adapters

6 simplex ST adapters 24 484824

12 duplex LC adapters to 2 MTP*

QuickNet ® Cassette Type

FMT1

(holds up to 4 cassettes)

Enclosure and Fiber count

FMT2A

(holds up to 6 cassettes)

6 duplex LC adapters to 1 MTP*

48 72

FMT2

(holds up to 8 cassettes)

FMT1A

(holds up to 3 cassettes)

366 duplex SC adapters to 1 MTP*

3 duplex SC adapters to 1 MTP* 24 364818

24 3648186 simplex ST adapters to 1 MTP*

O p t i C o m ® F i b e r O p t i c P a t c h P a n e l s a n d T r a y s CFAPPBL1 with FMT1 CFAPPBL1A with FMT1A

CFAPPBL2A with FMT2ACFAPPBL2 with FMT2

3.47 [88.1]

11.16 [283.5]

19.00 [482.60]

11.16 [283.5]

19.00 [482.60]

11.16 [283.5]

19.00 [482.60]

11.16 [283.5]

19.00 [482.60]

1.72 [43.7]

3.47 [88.1]

WORLDWIDE SUBSIDIARIES AND SALES OFFICES

PANDUIT CANADA

Markham, Ontario cs-cdn@panduit.com Phone: 800.777.3300

PANDUIT EUROPE LTD.

London, UK cs-emea@panduit.com Phone: 44.20.8601.7200

PANDUIT JAPAN

Tokyo, Japan cs-japan@panduit.com Phone: 81.3.6863.6000

PANDUIT SINGAPORE PTE. LTD.

Republic of Singapore cs-ap@panduit.com Phone: 65.6305.7575

PANDUIT AUSTRALIA PTY. LTD.

Victoria, Australia cs-aus@panduit.com Phone: 61.3.9794.9020

PANDUIT LATIN AMERICA

Jalisco, Mexico cs-la@panduit.com Phone: 52.33.3777.6000

Exhibit 42.1

Galvanized and Galfan Coated Guy & Static Strand

GALVANIZED STEEL STRAND MINIMUM BREAKING STRENGTH IN POUNDS

MINIMUM WEIGHT OF

COATING OZ./SQ. FT.

Strand Diameter Inches

Coated Diamter Inches

Wires Per Strand

Strand Weight/

1000 FT

Utilities Grade

Common Grade

Siemens- Martin Grade

High Strength Grade

Extra High Strength Grade

Class A Class B Class C

1/4 .120 3 117 3150 1860 3040 4730 6740 .85 1.70 2.55

1/4 .120 3 117 4500 .85 1.70 2.55

5/16 .145 3 171 6500 2490 4090 6350 9100 .90 1.80 2.70

3/8 .165 3 220 8500 3330 5560 8360 11800 .90 1.80 2.70

3/16 .062 7 73 1150 1900 2850 3990 .5 1.0 1.5

3/16 .065 7 80 2400 .5 1.0 1.5

7/32 .072 7 98 1540 2560 3850 5400 .5 1.0 1.5

1/4 .080 7 121 1900 3150 4750 6650 .6 1.2 1.8

9/32 .093 7 164 4600 2570 4250…