Preparation_for_Delivery_Shafts.pdf

PREPARATION FOR DELIVERY

All material shipped to the U.S. Coast Guard Surface Forces Logistics Center, Baltimore, MD, on this Contract/Delivery order, must be accompanied by an itemized packing list securely attached to the outside of the package.

All packing lists shall cite the Contract/Delivery Order Number with the package in such a manner as to provide identification.

Material shall be packed for shipment in such a manner as to afford adequate protection to the item against corrosion, deterioration, and physical damage during shipment from the supply source to Surface Forces Logistics Center locations.

Package shall also provide adequate protection for warehouse storage and multiple shipments.

All packages shall have the Contract/Delivery Order Number, Stock Number (if applicable), Vendor Name and Part Number clearly marked on the exterior of the package.

All deliveries are to be made Monday through Friday between the hours of 7:00 A.M. and 1:00 P.M.

BAR CODING FOR U.S. COAST GUARD

SURFACE FORCES LOGISTICS CENTER PROCURED MATERIAL

1.0 SCOPE

1.1. This specification outlines the Bar Code format, layout, & content requirements for all Surface

Forces Logistics Center Bar Coding, as well as all label variables available.

1.2. CLASSIFICATION

1.2.1. Labels - As illustrated and classified in MIL-PRF-61002.

1.2.2. TYPE “V” Special (see section 3.2.2.a. herein [TYPES]).

1.2.3. GRADES

a. Multiple Durability Requirements.

b. Adhesion, Condensation. Abrasion, Backing Sheet, and UV condensation.

c. Adhesion and Backing Sheet Requirements Only.

d. Special Durability Requirements (specify).

1.2.4. STYLES

1. Non-Porous Surfaces

PLDixon Typewritten Text

HSCG40-13-R-11003 ATTACHMENT 2

2. Porous Surfaces

3. Special surfaces (i.e., styrofoam, rubber, composites)

1.2.5. COMPOSITION

a. Paper (with or without laminate).

b. Plastic (with or without laminate), materials such as polyester, mylar, vinyl, etc.)

c. Polymide (with or without laminate)

d. Metal (specify), (includes steel, anodized aluminum, etc)

e. Anodized, Photo Sensitive, Aluminum (matte finish)

f. Ceramic

g. Special (specify)

2.0 APPLICABLE DOCUMENTS (use as required)

2.1. DOCUMENT AVAILABILITY - See section 6.0

2.2. GOVERNMENT DOCUMENTS - The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the documents listed here by number and date shall be those in the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto.

2.2.1. SPECIFICATIONS

a. MIL-PRF-61002A DATED 25 Sept 1995, Pressure-Sensitive Adhesive, for Bar Coding.

2.3. COMMERCIAL DOCUMENTS - The following documents form a part of this spe to the extent specified herein. The documents shall be the version listed by number and da from the referenced industry organization. Commercial documents may also be listed in the Department of Defense Index of Specifications and Standards (DODISS).

cification te

2.3.1. American National Standards Institute / AIM (ANSI/AIM)

a. ANSI/AIM-BC1, DATED 1995, Uniform Symbology Specification Code 39.

2.4. SPECIFICATION ORDER OF PRECEDENCE - In the event of a conflict between the text of this specification and the references cited herein, this specification shall take precedence.

3.0 REQUIREMENTS

3.1. BAR CODE

a. All bar coding required herein shall be Code 39, also called Code 3 of 9 in accordance with ANSI/AIM BC1

b. The bar coding shall not replace any other marking required, but be in addition to it.

3.2. LABELS & LABELING

3.2.1. Labels

a. The National Stock Number (NSN) shall be bar coded on all primary packaging and shipping containers, or palletized equipment, or directly on the equipment, where the NSN is required marking. No other information is required to be bar coded unless specified in the contract.

b. Bar code shall be black with white, or otherwise contrasting background.

c. The bar code label shall also contain the printed NSN placed directly below the bar code. (See Figure 1.) The bar code label shall not take the place of the printed NSN required as part of the overall marking requirements.

d. Bar code may be placed on the same label as all other required marking, or may be on its own separate label. If on its own label, the bar code shall be placed adjacent to other marked information without obstructing other markings.

3.2.2. CLASSIFICATIONS

a. TYPES - (V only) May be produced in roll or sheet form, and shall be large enough to contain all of the information required, and meet all spacing requirements in

ASTM/AIM BC1.

b. GRADES - All grades shall be as specified in MIL-PRF61002 see sections 3.2.1, &

6.1.2.3.

1) Intended for applications where the labels will endure prolonged out door conditions (longer than 2 weeks).

2) Intended for long term indoor applications with short term outdoor exposure (less than 2 weeks).

3) Intended for use when short term shipping or indoor conditions are expected.

4) When none of the above grades will suffice, see MIL-PRF61002 section

3.2.1 & 3.2.2.

c. STYLES - Label Mounting Surfaces

1. Non-Porous Surfaces

2. Porous Surfaces

3. Special Surfaces (i.e., styrofoam, rubber, composites) see 3.3.

d. COMPOSITION - The primary consideration is whether the label should be a paper based or plastic based label. See MIL-L-61002 section 6.1.2.4 for further clarification.

a. Paper (with or without laminate)

b. Plastic (with or without laminate), (includes materials such as polyester, mylar, vinyl,etc.).

c. Polymide (with or without laminate).

d. Metal (specify), (includes steel, anodized aluminum, etc).

e. Anodized, Photo Sensitive, Aluminum (matte finish)

f. Ceramic.

g. Special (specify).

3.2.3. LAMINATE - A clear laminate placed over the label may be required to meet the durability requirements for a given grade. If so required the final composite label shall be tested as a complete unit.

3.2.4. MARKING METHOD - The bar code marking method shall be in accordance with the selected label composition and tables 4 & 5 in MIL-L-61002.

3.3. ADHESIVE - The adhesive shall be pressure sensitive, water insoluble, and shall require no moisture, heat, or other preparation prior to, or after application to clean dry surfaces.

a. Refer to MIL-PRF-61002 section 3.1.6 if any other surface condition or method of application is specified.

3.4. NOTIFICATIONS & INSPECTIONS - The contractor shall be responsible for notifying the Contracting Officer at least seven (7) calendar days prior to said contractor being ready for any Quality Assurance (Q A.) inspections or monitored testing as required herein.

4.0 QUALITY ASSURANCE (QA)

4.1. RESPONSIBILITY FOR INSPECTION - The contractor is responsible for the performance of all inspection requirements as specified herein. The contractor may use his own or any other facilities for the performance of the inspections and tests, unless disapproved by the government. The government reserves the right to perform any of the inspections and tests set forth in this specification at any time.

4.2. RESPONSIBILITY FOR COMPLIANCE - All items shall meet the provisions of Sections 3

& 5. The inspections set forth in this specification shall become part of the contractor's overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Sampling for quality conformance does not authorize submission of known defective material (either indicated or actual) nor does it commit the government to acceptance of defective material.

4.3. TESTING - The testing as required in MIL-PRF-61002 shall be waived. The bar code shall be verified at its destination by a bar code reader.

4.3.1. The contractor shall verify readability of the bar coding.

5.0 PRESERVATION & PACKAGING, PACKING, & MARKING - All Labels shall be attached to their proper containers prior to shipment and quality assurance inspection.

6.0 NOTES

6.1. GOVERNMENT & COMMERCIAL DOCUMENT SOURCES

6.1.1. GOVERNMENT DOCUMENTS

a. Specifications and Standards (DODISS Documents) Standardization’s Document Order Desk 700 Robbins Avenue Building #4, Section D Philadelphia, PA 19111-5094 215-697-1187

b. DOD & Navy Publications and Forms (Other Than DODISS) Naval Publication and Forms Center 5801 Tabor Ave.

Philadelphia PA 19120 215-697-2000

6.1.2. COMMERICIAL DOCUMENTS

a. AIM USA (Standards Required Herein Approved by ANSI 1995) American National Standards Institute (ANSI) 25 West 43rd Street 4th Floor New York, N.Y. 10036

Phone: 212-642-4900