Amendment_003.pdf

1st Floor Courtroom and Chambers Renovation PBS-REG- 5 Joseph P. Kinneary U.S. Courthouse, Columbus, Ohio GS-05P-13-FB-C-0002

14. DESCRIPTION OF AMENDMENT/MODIFICATION

Amendment #003 is issued to make the following changes:

1.) The attached revised drawing AF-101 and specification section 09-6800, Carpeting, are incorporated.

2.) FAR 52.223-2, Affirmative Procurement of Biobased Products Under Service and Construction Contracts, is updated to include the following site to submit reports:

pbsbiobasedreporting@gsa.gov.

3.) Specification Sections 06 2000, 06 4100, and 06 4216, section 2.01, Manufacturers, are amended to include the following: Ted Bolle Millwork, 2834 Hurstead Road, Springfield, OH 45502, 937-325-8779; Stull Woodworks Inc., 7925 W. Fenner Rd., Ludlow Falls, OH 45339, 937-698-8181.

4.) Specification Section 08 1433, section 2.01, Manufacturers, is amended to include the following: Ted Bolle Millwork, 2834 Hurstead Road, Springfield, OH 45502, 937-325-8779; Tru Stile Doors, 6170 Centre Park Drive, Westchester, OH.

45069, 800-735-7923; Stull Woodworks Inc., 7925 W. Fenner Rd., Ludlow Falls, OH. 45339, 937-698-8181.

Solicitation terms and conditions not specifically addressed remain unchanged.

Joseph P. Kinneary US Courthouse, Columbus, Ohio GS-05P-13-FB-C-0002

CARPETING 09 6800 - 1

PROPERTY OF THE UNITED STATED GOVERNMENT

FOR OFFICIAL USE ONLY

Do not remove this notice

Properly destroy documents when no longer needed.

SECTION 09 6800

CARPETING

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Carpet, direct-glued.

B. Removal of existing carpet.

C. Accessories.

1.02 REFERENCE STANDARDS

A. ASTM D2859 - Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials; 2006.

B. ASTM F710 - Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring;

2008.

C. CRI (CIS) - Carpet Installation Standard; Carpet and Rug Institute; 2009.

D. CRI (GLA) - Green Label Testing Program - Approved Adhesive Products; Carpet and Rug Institute; Current Edition.

E. CRI (GLCC) - Green Label Testing Program - Approved Product Categories for Carpet Cushion; Carpet and Rug Institute; Current Edition.

1.03 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.

B. Shop Drawings: Indicate seaming plan, method of joining seams, direction of carpet pile and pattern, location of edge moldings and edge bindings.

C. Product Data: Provide data on specified products, describing physical and performance characteristics; sizes, patterns, colors available, and method of installation.

D. Samples: Submit two samples 36x36 inch in size illustrating color and pattern for each carpet and cushion material specified. Verification of color match will most likely take several submissions.

E. Submit two, 12 inch long samples of edge strip for each color specified.

F. Manufacturer's Installation Instructions: Indicate special procedures.

G. Maintenance Data: Include maintenance procedures, recommended maintenance materials, and suggested schedule for cleaning.

H. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 6000 - Product Requirements, for additional requirements.

2. Furnish extra material described below, before installation begins, which matches products installed, is packaged with protective covering for storage, and is identified with labels describing contents:

kahlev Cross-Out kahlev Cross-Out kahlev Callout 9 x 15

CARPETING 09 6800 - 2

PROPERTY OF THE UNITED STATED GOVERNMENT

FOR OFFICIAL USE ONLY

Do not remove this notice

Properly destroy documents when no longer needed.

a. Carpet: Full width rolls equal to 5% of amount installed for each type indicated but not less than 10 square yards.

I. Warranty: Submit a copy of the manufacturers standard warranty to the Procurement Officer.

Owner is to be the beneficiary of the terms of this warranty. Warranty begins at substantial completion.

J. Certificates as described in "General Carpet Criteria"

1.04 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing specified carpet with minimum three years documented experience.

B. Installer Qualifications: Company specializing in installing carpet with minimum three years experience.

1.05 FIELD CONDITIONS

A. Store materials in area of installation for minimum period of 24 hours prior to installation.

B. Maintain minimum 70 degrees F ambient temperature 24 hours prior to, during and 24 hours after installation.

C. Ventilate installation area during installation and for 72 hours after installation.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Carpet:

1. Basis of Design: The Mohawk Group; Product: Colorshield Textured.

2. Bentley; Product: Custom printed pattern to match Basis of Design.

3. Substitutions: See Section 01 6000 - Product Requirements.

B. Cushion:

1. Dura Undercushions Ltd; Product: Duracushion Double-stick: www.duracushion.com

2. Substitutions: See Section 01 6000 - Product Requirements.

2.02 CARPET

A. Carpet:See floor finish plan AF-101 for further information including configuration and pattern descriptions.

1. Product: Colorshield Textured 40 oz.manufactured by Mohawk.

2. Color: Patterned to include borders.

3. Pattern: To match approved sample available for review at the following: InterActive

Design, Inc., 308 W. Erie, Suite 506, Chicago, IL 60654; attn: Laurie Woolverton 312-482-8866 X323.

B. General Carpet Criteria

1. Performance Requirements

a. Static: Less than or equal to 3.5 kV when tested by AATCC Test Method 134 (Step Test Option) kahlev Cross-Out kahlev Cross-Out kahlev Cross-Out kahlev Cross-Out kahlev Cross-Out kahlev Text Box Except CPT BORDER-2 kahlev Callout Bentley Prince Street - See AF-101 kahlev Callout Bentley Prince Street - See AF-101 kahlev Text Box See AF-101

CARPETING 09 6800 - 3

PROPERTY OF THE UNITED STATED GOVERNMENT

FOR OFFICIAL USE ONLY

Do not remove this notice

Properly destroy documents when no longer needed.

b. Surface Flammability Ignition: Meets CPSC-FF-1-70, DOC-FF-1-70 Methenamine Tablet Test Criteria.

c. Flooring Radiant Panel Test: Meets NFPA Class I or II depending upon occupancy and Fire Code when tested under ASTM E-648 for glue down installation

d. Smoke Density: NBS Smoke Chamber - Less than 450 Flaming Mode when tested under ASTM E-662

e. General Note on Testing: Testing must be performed in a NVLAP accredited laboratory.

2. Low Emitting Materials: The carpet and floor adhesive (for glue down installations) must meet the Green Label Plus (GLP) and floor adhesive requirements of the Carpet and Rug Institute (CRI). GLP number must be provided. Carpet and all installation components including adhesives, sealers, seam welds and seam sealers must meet the Low Emitting Materials Standards as outlined in the US Green Building Council Criteria.

3. VOC Content: Adhesives must meet VOC content standards per South Coast Air Quality Management District Rule #1168

4. Recycled Content: Recycled content of the Total Product Weight must be either Pre-consumer or Post-consumer

a. Broadloom: 10%

5. Product Sustainability and Environmental Requirements: To achieve superior performance in multiple environmental attribute areas, carpet must have third party certification in accordance with NSF 140 2007 e; Sustainable Carpet Assessment Standard at a "Gold" Level minimum. Carpet manufacturer must supply certificate as part of the procurement documentation.

6. Face Fiber Content: Face yarn must be 100% nylon fiber. Loop Pile shall be 100% Bulk Continuous Filament (BCF); cut and loop shall be 100% BCF for loop portion and may be BCF or staple for the cut portion; cut pile carpet shall be staple or BCF.

7. Additional Requirements for Broadloom

a. Edge Ravel - Minimum 1 lb. Loop Pile only ASTM D-7267

b. Delamination - Minimum 3.5 lb. per inch of width - ASTM D-3936

c. Tuft Bind - Minimum 10 lb. average tuft bind for Loop Pile - ASTM D-1335

8. Texture Appearance Retention Rating (TARR) - Carpet must meet TARR of not less than 3.0.

a. Carpet should be evaluated using ASTM D-5252 Hexapod Drum Test as per the commercial carpet test

2.03 CUSHION

A. Cushion: Cellular rubber:

1. VOC Content: Provide CRI Green Label certified product; in lieu of labeling, independent test report showing compliance is acceptable.

2. Product: Duracushion Double-stick manufactured by Dura UndercushionsLtd.

3. Nominal Thickness: 0.235 inch.

4. Roll Width: 54 inches.

5. Weight: 64 oz/sq yd.

6. Density: 22 lb/cu ft.

7. Flammability: Class 1 rating for ASTM E648 Radiant Panel test.

2.04 ACCESSORIES

kahlev Cross-Out

CARPETING 09 6800 - 4

PROPERTY OF THE UNITED STATED GOVERNMENT

FOR OFFICIAL USE ONLY

Do not remove this notice

Properly destroy documents when no longer needed.

A. Sub-Floor Filler: Type recommended by carpet manufacturer.

B. Tackless Strip: Carpet gripper, of type recommended by carpet manufacturer to suit application, with attachment devices.

C. Moldings and Edge Strips: Embossed aluminum, color as selected.

D. Adhesives - General: Compatible with materials being adhered; maximum VOC content of 50 g/L; CRI Green Label certified; in lieu of labeled product, independent test report showing compliance is acceptable.

E. Seam Adhesive: Recommended by manufacturer.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify that sub-floor surfaces are smooth and flat within the tolerances specified for that type of work and are ready to receive carpet.

B. Verify that wall surfaces are smooth and flat within the tolerances specified for that type of work, are dust-free, and are ready to receive carpet.

C. Verify that sub-floor surfaces are dust-free and free of substances that could impair bonding of adhesives to sub floor surfaces.

D. Verify that required floor-mounted utilities are in correct location.

3.02 PREPARATION

A. Remove existing carpet and carpet cushion.

B. Prepare floor substrates as recommended by flooring and adhesive manufacturers.

C. Remove sub-floor ridges and bumps. Fill minor or local low spots, cracks, joints, holes, and other defects with sub-floor filler.

D. Apply, trowel, and float filler to achieve smooth, flat, hard surface. Prohibit traffic until filler is cured.

E. Clean substrate.

3.03 INSTALLATION - GENERAL

A. Starting installation constitutes acceptance of sub-floor conditions.

B. Install carpet and cushion in accordance with manufacturer's instructions and CRI Carpet Installation Standard.

C. Verify carpet match before cutting to ensure minimal variation between dye lots.

D. Lay out carpet and locate seams in accordance with shop drawings:

1. Locate seams in area of least traffic, out of areas of pivoting traffic, and parallel to main traffic.

2. Do not locate seams perpendicular through door openings.

3. Align run of pile in same direction as anticipated traffic and in same direction on adjacent pieces.

kahlev Cross-Out kahlev Cross-Out

CARPETING 09 6800 - 5

PROPERTY OF THE UNITED STATED GOVERNMENT

FOR OFFICIAL USE ONLY

Do not remove this notice

Properly destroy documents when no longer needed.

4. Locate change of color or pattern between rooms under door centerline.

5. Provide monolithic color, pattern, and texture match within any one area.

E. Install carpet tight and flat on subfloor, well fastened at edges, with a uniform appearance.

3.04 DIRECT-GLUED CARPET

A. Double cut carpet seams, with accurate pattern match. Make cuts straight, true, and unfrayed.

Apply seam adhesive to cut edges of woven carpet immediately.

B. Apply contact adhesive to floor uniformly at rate recommended by manufacturer. After sufficient open time, press carpet into adhesive.

C. Apply seam adhesive to the base of the edge glued down. Lay adjoining piece with seam straight, not overlapped or peaked, and free of gaps.

D. Roll with appropriate roller for complete contact of adhesive to carpet backing.

E. Trim carpet neatly at walls and around interruptions.

F. Complete installation of edge strips, concealing exposed edges. Bind cut edges where not concealed by edge strips.

3.05 CLEANING

A. Remove excess adhesive from floor and wall surfaces without damage.

B. Clean and vacuum carpet surfaces.

END OF SECTION

RECESSED CONCRETE FLOOR

BOX W/ACCESS PANEL TO

RECEIVE CARPET INSERT

(REFER TO ELECTRICAL

DOCUMENTS FOR SPECIFIC

PRODUCT DESCRIPTION)

CARPET BORDER 2 -

12" MEDALLION FROM

DURKAN "SUMMERLY"

COLLECTION -

DURKAN PATTERN

NUMBER D16476C

FLOOR FINISH LEGEND

C A

R P

E T

D E

V I C

E S

CARPET PATTEN 2 -

BECK DYED SOLID TO

MATCH DURKAN COLOR

NUMBER 5C5

CARPET BORDER 1 -

SOLID BORDER; DURKAN

PATTERN NUMBER

D16476B

CARPET PATTERN 1 -

PRINTED LEAF PATTERN -

DURKAN PATTERN NUMBER

D9045

FB

COURTROOM FLOOR FINISH PLAN

FLOOR PLAN

N

CPT -PATT-1

CPT -PATT-1

CPT -PATT-1

CPT -BORDER-1

CPT -BORDER-1

CPT -PATT-1

CPT -PATT-1 CPT -PATT-1

CPT -PATT-2

CPT -PATT-2 CPT -PATT-2

CPT -PATT-2CPT -PATT-2

CPT -BORDER-2

SOLID WOOD

NOSING

SOLID WOOD

NOSING

SOLID WOOD

NOSING AT

STEPS - TYP.

JURY BOX

MILLWORK

RAILING

JUDGE'S BENCH

SCREEN

CLERKS' BENCH

DEPUTY'S

STATION

REPORTER STATIONS /

WITNESS BOX

COUNSEL

TABLES

(SEE FLOOR

PLAN FOR

LOCATION)

LECTERN

(SEE FLOOR

PLAN FOR

LOCATION)

GALLERY

RAILING

PUBLIC

SEATING

FB

FB

FB

CPT -BORDER-1

CPT -PATT-2

CPT -PATT-1

CPT -BORDER-2

UP

UPUP

UP UP

TYPICAL AT FOUR CORNERS OF

CENTER FIELD ONLY - ORIENT

MEDALLIONS AS INDICATED

(MIRRORED ABOUT EAST/WEST

CENTER LINE

CPT -BORDER-1

CPT -BORDER-1

CPT -BORDER-1

CENTER FLOOR BOX

WITHIN ENCLOSED

RACEWAY BELOW TABLE

SURFACE - TYP.

MEASURED

FROM FINISH

FACE OF RAILING

TYP.

(EQ) (EQ)

SHEET NOTES:

1. DIMENSIONS OFF PERIMETER ARE

MEASURED TO FACE OF WAINSCOT WALL

PANELING - TYP.

LINE OF ACCESS

PANEL AT CABLE

RACEWAY BENEATH

BENCH

DASHED LINES DENOTE WORK

SURFACES ABOVE - TYP.

kahlev Cross-Out kahlev Cross-Out kahlev Cross-Out kahlev Cross-Out kahlev Text Box Bentley Prince Street Sales Rep Mindy Dever 859-536-7846 mindy.dever@bentleyprincestreet.com kahlev Callout Bentley Prince Street Moda Colore Pattern: Agnona

PDS: 142394-002

Colors: 880346/880390 kahlev Callout Bentley Prince Street Kings Road Color: Overcast, 880346 kahlev Callout Bentley Prince Street Kings Road Color: Sanctuary 880390 kahlev Callout Bentley Prince Street Kings Road Carved Lotus Leaf Accent Color: Yellow Lab 880378 (5 Yard Min. for Kings Road) kahlev Typewritten Text kahlev Typewritten Text kahlev Typewritten Text kahlev Text Box chris01 chris01