10522_en.doc

SECTION 10522

FIRE EXTINGUISHER, HOSE AND VALVE CABINETS AND ACCESSORIES

PART 1 - GENERAL

1.1 SUBMITTALS

1.1.1 Product Data

a.

Fire extinguisher cabinet b.

Fire hose and valve cabinet

Submit for each item specified. Include descriptions of materials, finishes, fastening and anchoring devices, and appurtenances.

1.1.2 Samples

Color chart

Colors of finishes shall closely approximate colors indicated.

1.1.3 Certificates

R.E.I. listing

Submit for each type of accessory specified, attesting that materials meet the specified requirements.

1.2 QUALITY ASSURANCE

1.2.1 Coordination

Verify that cabinets are sized to accommodate type and capacity of extinguishers to be provided by the Government.

1.2.2 R.E.I. Listed Products

The following products shall bear the R.E.I. listing mark as appropriate for the product.

1.2.3 Cabinets

R.E.I. listing mark matching the fire resistance rating of the wall where it is installed.

1.3 DELIVERY, STORAGE, AND HANDLING

Deliver materials to the site in unopened containers, labeled with the manufacturer's names and brands, ready for installation. Store accessories in safe, dry locations until needed for installation.

PART 2 - PRODUCTS

2.1 MATERIALS

2.1.1 Galvanized Steel Sheet

2.1.2 Solid Brass

2.1.3 Glass

2.1.3.1 Tempered Glass.

Kind FT (fully tempered), Condition A (uncoated), Type 1, Class 1(transparent).

2.2 FINISHES

Provide manufacturer's standard color chart to verify specified finishes. Protect metal finishes on exposed surfaces from damage by applying temporary strippable protective covering prior to shipping.

2.2.1 Baked Enamel (Interior Steel Surfaces)

Immediately after cleaning and pretreatment, apply manufacturer's standard two coat baked enamel finish consisting of prime coat and thermosetting topcoat. Comply with paint manufacturer's instructions for applying and baking to achieve a minimum dry film thickness of 2.0 mils.

2.2.2 Exterior Surfaces

Shall be solid brass with satin finish and clear protective coating.

2.3 MANUFACTURED UNITS

2.3.1 Cabinets

Provide cabinet box (tub) with trim, frame, door and hardware. Miter and weld door frames and door stiles at corner. Remove or blend tool and die marks and stretch lines into finish. Fabricate cabinets in accordance with commercial practice, with welds ground smooth. Bend, flange, draw, form, and perform similar operations in a manner to ensure no defects. Flanges of recessed cabinets to return to walls to provide a continuous, tight against the wall installation. Doors shall be warp free. Reinforce doors and frames for hardware.

2.3.1.1 Fire Extinguisher Cabinet

a.

Box Mounting: Wall mounted.

b.

Box Size: Width 320, depth 250, height 600 millimeters nominal.

c.

Box Material and Finish: Red baked acrylic enamel.

d.

Trim Style: Exposed trim rolled edge.

e.

Trim Material and Finish: Solid brass for all exterior trim.

f.

Door Style: Stile and rail, full glazed.

g.

Door Material and Finish: Solid brass.

h.

Door Glazing: Tempered glass, clear.

i.

Hardware: Manufacturers standard brass wire pull with self adjusting roller catch.

j.

Fire Rating: Match fire resistance rating of wall where installed.

2.3.1.2 Fire Hose and UNI 45 Valve Cabinet

a. Box Mounting: Recessed.

b. Box Size: Width 370, depth 180, height 560 millimeters nominal

c. Box Material and Finish: Red baked acrylic enamel.

d. Trim Style: Exposed trim rolled edge.

e. Trim Material and Finish: Brushed stainless steel.

f. Door Style: Stile and rail, full glazed.

g. Door Material and Finish: Red baked acrylic enamel.

h. Door Glazing: Tempered glass, clear.

i. Hardware: Manufacturer's standard steel wire pull with self adjusting roller catch.

j. Fire Rating: Match fire resistance rating of wall where installed.

k. Length of Hose: One hose rack with 20 meters of hose.

2.3.2 Mounting Brackets

Provide brackets for extinguishers not located in cabinets sized to accommodate fire extinguisher provided by the Government. Bracket design shall prevent accidental dislodging of the extinguisher, of sizes required for the type and capacity of the extinguisher to be provided.

Material and Finish: Stainless steel, reflective polish.

PART 3 – EXECUTION

3.1

INSTALLATION

Follow manufacturer's printed instructions for installation. After acceptance of accessories, remove and dispose of strippable plastic protection. Coordinate accessory manufacturer's mounting details with other trades as their work progresses. Install in locations and at mounting heights indicated. Surfaces of fastening devices exposed after installation shall have the same finish as the attached accessory. Exposed screw heads shall be oval. Protect exposed surfaces of accessories with strippable plastic or by other means until the installation is accepted. After installation, thoroughly clean exposed surfaces and restore damaged work to its original condition or replace with new work.

-- End of Section --

Section 10522

Section 10522