Questions from Contractor Corrected typos.pdf

1. ITEM NO. 0004 Which manufacture for VCT such as Manninton Azorock etc and Specification.

ANSWER: As stated in the Specifications attached in the solicitation SECTION 09650 – RESILIENT FLOORING Para 2.1

2.1 VINYL COMPOSITION TILE (VCT) shall conform to ASTM F 1066, Class 2 through pattern tile, composition 1, asbestos‐free, and shall be 12 inches square and 1/8 inch thick as manufactured by Azrock or equal. Tile shall be of the color and surface pattern as described in the Task Order with the color and pattern uniformly distributed throughout the thickness of the tile. Flooring in any one continuous area shall be from the same lot and shall have the same shade and pattern.

Installation of VCT shall include stripping and applying a wax/sealer in accordance with manufacturer’s recommendations.

2. ITEM NO. 0007 Need the Max Quantity. The Max Quantity listed stated Undefined.

ANSWER: CLIN 0009 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0007AA, 0007AB, AC etc… are priced Sub‐Clins of CLIN 0007.

3. ITEM NO. 0009 What is the amt of carpet tile. The Max Quantity listed stated Undefined. Need amount and Manufacture and Specification.

Answer: CLIN 0009 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0009AA, 0009AB are priced Sub‐Clins of CLIN 0009.

4. ITEM NO. 0011 Need amount of rubber base color, manufacture and specification. Amount listed Quantity undefined.

ANSWER: CLIN 0011 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0011AA, 0011AB are priced Sub‐Clins of CLIN 0011.

5. ITEM NO 0011AA Need color, manufacture and specification.

FLOORING Para 2.4

RUBBER WALL BASE: Rubber wall base shall conform to Fed. Spec. SS‐W‐40, Type I (rubber), Style B (cove). Rubber base shall be 4‐inches high and/or 6‐inches roll stock (minimum 100ft and/or longest practical lengths), minimum 0.125‐inch thick, and color shall be limited to 3 colors as determined by the submittal, as manufactured by Burke Mercer or equal. Rubber wall base shall be cut to length of wall and stair. Butt joints shall be kept to a minimum. No vinyl wall base will be accepted.

6. ITEM NO 0011AB need color manufacture, specifications and quantity.

FLOORING Para 2.4

RUBBER WALL BASE: Rubber wall base shall conform to Fed. Spec. SS‐W‐40, Type I (rubber), Style B (cove). Rubber base shall be 4‐inches high and/or 6‐inches roll stock (minimum 100ft and/or longest practical lengths), minimum 0.125‐inch thick, and color shall be limited to 3 colors as determined by the submittal, as manufactured by Burke Mercer or equal. Rubber wall base shall be cut to length of wall and stair. Butt joints shall be kept to a minimum. No vinyl wall base will be accepted.

7. ITEM NO 0012 Need the Max Quantity. The max Quantity listed stated Undefined. Need Manufacture and Specification.

ANSWER: CLIN 0012 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0012AA, 0012AB are priced Sub‐Clins of CLIN 0012.

9. ITEM NO 0012AA Need manufacture and specification.

ANSWER: ANSWER: As stated in the Specifications attached in the solicitation SECTION 09650 – RESILIENT FLOORING Para 2.4

RUBBER WALL BASE: Rubber wall base shall conform to Fed. Spec. SS‐W‐40, Type I (rubber), Style B (cove). Rubber base shall be 4‐inches high and/or 6‐inches roll stock (minimum 100ft and/or longest practical lengths), minimum 0.125‐inch thick, and color shall be limited to 3 colors as determined by the submittal, as manufactured by Burke Mercer or equal. Rubber wall

10. ITEM NO 0012AB Need manufacture and specification.

FLOORING Para 2.4

RUBBER WALL BASE: Rubber wall base shall conform to Fed. Spec. SS‐W‐40, Type I (rubber), Style B (cove). Rubber base shall be 4‐inches high and/or 6‐inches roll stock (minimum 100ft and/or longest practical lengths), minimum 0.125‐inch thick, and color shall be limited to 3 colors as determined by the submittal, as manufactured by Burke Mercer or equal. Rubber wall

11. ITEM NO 0014 Need manufacture and specification.

FLOORING Para 2.2

Rubber tile shall conform to ASTM F‐1344, Class 1 homogeneous construction Type A solid color.

Surface shall be raised round or mini‐pastille studs with chamfered edges. Stud profile shall be high and/or low. Overall thickness shall be 1/8‐inch thick. Color and pattern shall be as described in the Task Order.

12. ITEM NO 0015 Need manufacture and specification.

FLOORING Para 2.3

2.3 RUBBER STAIR TREADS/RISERS: Treads and risers shall conform to FS RR‐T‐650 composition A, (rubber). Design shall be a two piece nosing/tread with a matching coved riser. Treads shall have raised circular, ribbed or diamond cut pattern, as described in the Task Order, in continuous length up to 72". Two‐piece Treads shall be minimum 12‐1/2" wide and cut to width of existing stair tread. Treads shall be minimum 3/16 inch thick. Treads shall have a nonskid safety pattern, of type standard with the manufacturer, molded into the tread. The safety pattern shall cover approximately 9" from the front edge, with a smooth area of approximately 3" width at the rear edge. Overall thickness of the safety pattern portion of the tread and front edge shall be a minimum thickness of 1/4". The smooth portion of the tread shall taper to a thickness of 3/16" Rubber coved risers shall be the product of the rubber stair tread manufacturer. Risers shall be top‐set cove type, 1/8" thick, 7" height, with 5/8" coved toe, and ribbed back. Lengths shall be as required to cover each riser in a maximum of two pieces.

Treads/risers shall be equal to Roppe.

13. ITEM NO 0017 Need Max Quantity. Max quantity listed undefined. Need Manufacturer and specification.

ANSWER: CLIN 0017 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0017AA, 0017AB are priced Sub‐Clins of CLIN 0017.

14. ITEM NO 0017AA Need size of tile manufacture and specification.

ANSWER: As stated in the Specifications attached in the solicitation SECTION 09310 – CERAMIC TILE Para 2.1 & 2.1.3

2.1 TILE: Tile shall conform to ANSI A137.1. Containers shall be grade sealed. Seals shall be marked to correspond with the marks on the signed master grade certificate. Tile shall be impact resistant with a minimum breaking strength of 250 pounds (lbs.) in accordance with ASTM C 648. Water absorption shall be 0.50 maximum percent in accordance with ASTM C 373.

Floor tile shall have a minimum coefficient of friction of 0.50 wet and dry in accordance with ASTM C 1028. Floor tile shall be Class IV‐Heavy or Class IV‐Plus‐Extra Heavy, as required by the task order. Traffic, durability classification as rated by the manufacturer when tested in accordance with ASTM C 1027 for abrasion resistance as related to foot traffic. All tiles shall be as manufactured by Monarch or equal. Tile sizes shall be as described in the Task Order.

2.1.3 CERAMIC MOSAIC TILE: Tile and trim shall be unglazed porcelain with cushion edged. Tile sizes shall be of size and color as described in the Task Order.

15. ITEM NO 0017AB Quarry tile size, manufacturer and specification.

ANSWER: As stated in the Specifications attached in the solicitation SECTION 09310 – CERAMIC TILE Para 2.1‐2.1.2

2.1 TILE: Tile shall conform to ANSI A137.1. Containers shall be grade sealed. Seals shall be marked to correspond with the marks on the signed master grade certificate. Tile shall be impact resistant with a minimum breaking strength of 250 pounds (lbs.) in accordance with ASTM C 648. Water absorption shall be 0.50 maximum percent in accordance with ASTM C 373.

Floor tile shall have a minimum coefficient of friction of 0.50 wet and dry in accordance with ASTM C 1028. Floor tile shall be Class IV‐Heavy or Class IV‐Plus‐Extra Heavy, as required by the task order. Traffic, durability classification as rated by the manufacturer when tested in accordance with ASTM C 1027 for abrasion resistance as related to foot traffic. All tiles shall be as manufactured by Monarch or equal. Tile sizes shall be as described in the Task Order.

2.1.2 QUARRY TILE: Quarry Tile shall be of size and color as described in the Task Order.

16. ITEM NO. 0017AC Need size, manufacture and specification (tile base size)

ANSWER: As stated in the Specifications attached in the solicitation SECTION 09310 – CERAMIC TILE Para 2.1‐2.1.2

2.1 TILE: Tile shall conform to ANSI A137.1. Containers shall be grade sealed. Seals shall be marked to correspond with the marks on the signed master grade certificate. Tile shall be impact resistant with a minimum breaking strength of 250 pounds (lbs.) in accordance with ASTM C 648. Water absorption shall be 0.50 maximum percent in accordance with ASTM C 373.

Floor tile shall have a minimum coefficient of friction of 0.50 wet and dry in accordance with ASTM C 1028. Floor tile shall be Class IV‐Heavy or Class IV‐Plus‐Extra Heavy, as required by the task order. Traffic, durability classification as rated by the manufacturer when tested in accordance with ASTM C 1027 for abrasion resistance as related to foot traffic. All tiles shall be as manufactured by Monarch or equal. Tile sizes shall be as described in the Task Order.

2.1.4 TILE BASE: Tile base shall be cushion edged with a finely textured glaze. Tile shall be of size and in colors as described in the Task Order.

17. ITEM NO. 0019 Need amount of tiolet (s) Size and specification (example standard tiolet handicap tiolet etc)

ANSWER: CLIN 0019AA & 0019AB are for removal/ re‐installation of existing toilets and/or stalls.

18. ITEM 0020 Amount of metal reducers.

ANSWER: Quantities specified in in Sub Clins 0020AA‐0020AD

19. ITEM 0021 Need max amount quantity. Max quantity listed undefined. Need manufacture and specification.

ANSWER: CLIN 0021 is an informational CLIN only. The quantities are listed in the Sub‐Clins below for example 0021AA, 0021AB are priced Sub‐Clins of CLIN 0021.

20. ITEM 0021AA VCT Need manufacture and specification.

ANSWER: CLIN 0021AA is for the Stripping and Applying of Wax Sealant to existing VCT

21. ITEM 0021 AD Cove base need color manufacture and specification.

ANSWER: CLIN 0021AD is for the installation of existing Cove Base.