Exhibit D - CDRL A008 DD-1494 Form Example - NGT II.pdf

APPENDIX G

APPLICATION FOR EQUIPMENT FREQUENCY ALLOCATION

(DD 1494)

Contains the following DD 1494 Forms and Instructions:

DOD GENERAL INFORMATION

TRANSMITTER EQUIPMENT CHARACTERISTICS

RECEIVER EQUIPMENT CHARACTERISTICS

ANTENNA EQUIPMENT CHARACTERISTICS

NTIA GENERAL INFORMATION

SAMPLE LINE DIAGRAM

leland.wannamaker Note Accepted set by leland.wannamaker leland.wannamaker Note Accepted set by leland.wannamaker leland.wannamaker Note MigrationConfirmed set by leland.wannamaker leland.wannamaker Note Completed set by leland.wannamaker leland.wannamaker Note Accepted set by leland.wannamaker leland.wannamaker Note Completed set by leland.wannamaker leland.wannamaker Note Accepted set by leland.wannamaker jody.greenwood Sticky Note Accepted set by jody.greenwood

CLASSIFICATION DATE Form Approved APPLICATION FOR EQUIPMENT OMB No. 0704-0188

FREQUENCY ALLOCATION

PAGE 1 OF PAGES

The public reporting burden for this collection of information is estimated to average 24 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services and Communications Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ORGANIZATION. RETURN COMPLETED FORM TO THE USING AGENCY OR CONTRACTING AGENCY, AS APPROPRIATE.

DOD GENERAL INFORMATION

TO FROM

1. APPLICATION TITLE

2. SYSTEM NOMENCLATURE

3. STAGE OF ALLOCATION (X one)

a. STAGE 1 - CONCEPTUAL b. STAGE 2 - EXPERIMENTAL c. STAGE 3 - DEVELOPMENTAL d. STAGE 4 - OPERATIONAL

4. FREQUENCY REQUIREMENTS

a. FREQUENCY(IES)

b. EMISSION DESIGNATOR(S)

5. TARGET STARTING DATE FOR SUBSEQUENT STAGES

a. STAGE 2 b. STAGE 3 c. STAGE 4

6. EXTENT OF USE

7. GEOGRAPHICAL AREA FOR

a. STAGE 2

b. STAGE 3

c. STAGE 4

8. NUMBER OF UNITS

a. STAGE 2 b. STAGE 3 c. STAGE 4

9. NUMBER OF UNITS OPERATING SIMULTANEOUSLY IN THE SAME ENVIRONMENT

10. OTHER J/F 12 APPLICATION NUMBER(S) TO BE 11. IS THERE ANY OPERATIONAL REQUIREMENT AS DESCRIBED IN

THE INSTRUCTIONS FOR PARAGRAPH 11?

b RELATED J/F 12/

a. SUPERSEDED J/F 12/

a. YES b. NO c. NAvail

12. NAMES AND TELEPHONE NUMBERS

a. PROGRAM MANAGER (1) COMMERCIAL (2) AUTOVON

b. PROJECT ENGINEER (1) COMMERCIAL (2) AUTOVON

13. REMARKS

DOWNGRADING INSTRUCTIONS CLASSIFICATION

DD FORM 1494, AUG 96 PREVIOUS EDITION MAY BE USED.

INSTRUCTIONS FOR COMPLETING DD FORM 1494,

"APPLICATION FOR EQUIPMENT FREQUENCY ALLOCATION"

GENERAL INFORMATION

CLASSIFICATION: This form must be classified in accordance with appropriate agency security directions. Downgrading instructions must be indicated. The highest classification for each item or sub-item as required must be indicated by a (U), (C), or (S) alongside the item or sub-item title, for classified applications.

APPLICATION PURPOSE: This is an application for development or procurement of equipment with RF emitters. It is not a frequency assignment request for operation of RF emitters. Funds must not be obligated prior to the approval of an application for frequency allocation.

DATA REQUIREMENT: All applicable data items shall be submitted for all stages. Estimated values or ranges of values may be submit-ted for Stage 1 and 2 in the absence of calculated or measured values and shall be annotated (EST). Values for Stages 3 and 4 should be measured.

STANDARDS: Technical parameters of the application will be evaluated against the appropriate DoD, National and International EMC standards.

REMARKS ITEMS: Use the remarks item located at the bottom of each page of the form to amplify or clarify the entries. Add continuation pages as required.

ABBREVIATIONS:

Hertz Hz microseconds usec kilohertz kHz decibel dB megahertz MHz dB isotropic dBi gigahertz GHz pulses per second pps milliwatt mW parts per million ppm watt W peak envelope power PEP nanoseconds nsec not applicable NA National NTIA not available NAvail Telecommunications occupied bandwidth OC-BW

& Information Administration

HOW TO ASSEMBLE THE FORM:

FOR US COORDINATION:

1. DoD General Information Page

2. Transmitter Page(s)

3. Receiver Page(s)

4. Antenna Page(s)

5. Line Diagram(s)

6. Space Systems Data, if applicable

7. Continuation Page(s) (cross reference pages)

8. NTIA General Information Page

FOR FOREIGN COORDINATION: If this form is used to obtain foreign national frequency supportability comments, see the instructions on the back of the Foreign Coordination General Information Page.

DOD GENERAL INFORMATION PAGE

ITEM 1 - Application Title. Enter the Government nomenclature of the equipment, or the manufacturer's name and model number, and a short descriptive title.

ITEM 2 - System Nomenclature. Enter the nomenclature of the system for which this equipment is a subsystem, e.g., PATRIOT or Global Positioning System.

ITEM 3 - Stage of Allocation. Mark the appropriate block using the following NTIA definitions.

Stage 1 - Conceptual. The initial planning effort has been completed, including proposed frequency bands and other available characteristics.

Stage 2 - Experimental. The preliminary design has been completed, and radiation, using test equipment or preliminary models, may be required.

Stage 3 - Developmental. The major design has been completed, and radiation may be required during testing.

Stage 4 - Operational. Development has been essentially completed, and final operating constraints or restrictions required to assure compatibility need to be identified.

ITEM 4 - Frequency Requirements.

a. Enter the required frequency band(s). For equipment designed to operate only at a single frequency, enter this frequency. Indicate units, e.g., kHz, MHz, or GHz.

b. Enter the emission designator(s) including the necessary band-width for each designator, as described in Chapter 9 of the NTIA Manual e.g., 40M0PON. Identify each mode as hopping or non-hopping, e.g. 64M0F3E (Hopping).

Enter in Item 13, "Remarks," any other information pertinent to frequency requirements, such as minimum frequency separation or special relationships involving multiple discrete frequencies.

ITEM 5 - Target Starting Date for Subsequent Stages. Enter proposed date of application submission for each subsequent stage.

ITEM 6 - Extent of Use. Describe extent of use that will apply to Stage 4, e.g., continuous or intermittent. If intermittent, provide information including the expected number of hours of operation per day or other appropriate time period; scheduling capability; and any conditions governing the times of intermittent use, e.g., used only during terminal guidance phase, used only as required for calibration of test range equipment.

ITEM 7 - Geographical Area. Enter geographical location(s) or area(s) of use for this and subsequent stage(s), e.g., Gilfillan Plant, Los Angeles, California, and White Sands Missile Range, New Mexico (Stage 2); US&P (Stage 3); US&P, NATO Countries and Korea (Stage 4). Provide geographical coordinates (degrees, minutes, seconds) if available.

ITEM 8 - Number of Units. Enter total number of units planned for the stage review requested and the subsequent stages.

ITEM 9 - Number of Units Operating Simultaneously in the Same Environment. Enter maximum number of these units planned to be operating simultaneously in the same environment during Stage 4 use.

ITEM 10 - Other J/F 12 Application Number(s). Mark appropriate block(s) and enter J/F 12 number(s) for superseded and/or related application(s).

ITEM 11 - Operational Requirement. If this equipment will operate with the same or similar equipment used by other US Military Services, DoD Components, US Government Agencies or Allied Nations, mark "Yes," and specify in Item 13, "Remarks," the Services, Agencies or countries (to include the country's services).

ITEMS 12 and 13 - Self-explanatory.

DD FORM 1494, AUG 96 DoD General Information Page (Back)

CLASSIFICATION PAGE

TRANSMITTER EQUIPMENT CHARACTERISTICS

1. NOMENCLATURE, MANUFACTURER’S MODEL NO. 2. MANUFACTURER’S NAME

3. TRANSMITTER INSTALLATION 4. TRANSMITTER TYPE

5. TUNING RANGE 6. METHOD OF TUNING

7. RF CHANNELING CAPABILITY 8. EMISSION DESIGNATOR(S)

9. FREQUENCY TOLERANCE

10. FILTER EMPLOYED (X one)

a. YES b. NO

11. SPREAD SPECTRUM (X one) 12. EMISSION BANDWIDTH (X and complete as applicable)

a. YES b. NO CALCULATED MEASURED

13. MAXIMUM BIT RATE a. -3 dB

b. -20 dB

14. MODULATION TECHNIQUES AND CODING c. -40 dB

d. -60 dB

e. OC-BW

15. MAXIMUM MODULATION FREQUENCY

17. DEVIATION RATIO16. PRE-EMPHASIS (X one)

a. YES b. NO

18. PULSE CHARACTERISTICS

19. POWER a. RATE

a. MEAN b. WIDTH

b. PEP c. RISE TIME

20. OUTPUT DEVICE d. FALL TIME

e. COMP RATIO

21. HARMONIC LEVEL

22. SPURIOUS LEVEL a. 2ND

b. 3RD

23. FCC TYPE ACCEPTANCE NO.

c. OTHER

24. REMARKS

CLASSIFICATION

DD FORM 1494, AUG 96

TRANSMITTER EQUIPMENT CHARACTERISTICS PAGE

ITEM 13 - Maximum Bit Rate. Enter the maximum information bit Government assigned alphanumeric equipment designation. If above is ITEM 1 - Nomenclature, Manufacturer’s Model No. Enter the rate for digital equipment, in bits per second. If spread spectrum is not available, enter the manufacturer’s model number, e.g., MIT 502, and used, enter the bit rate after encoding.

complete Item 2. If above is not available, enter a short descriptive title, e.g., ATS-6 telemetry transmitter. ITEM 14 - Modulation Techniques and Coding. Describe in detail the modulation and/or coding techniques employed. For complex ITEM 2 - Manufacturer’s Name. Enter the manufacturer’s name if modulation schemes such as direct sequence spread spectrum, available. If a manufacturer’s model number is listed in Item 1, this item frequency hopping, frequency agile, etc., enter full details in Item 24, must be completed. "Remarks."

ITEM 15 - Maximum Modulation Frequency. For frequency or ship(s), plane(s) or building(s), etc., where the transmitter(s) will be ITEM 3 - Transmitter Installation. List specific type(s) of vehicle(s), phase modulated transmitter enter the maximum modulation or installed. baseband frequency. This frequency is assumed to be the frequency at -3 dB point on the high frequency side of the modulator response ITEM 4 - Transmitter Type. Enter the generic class of the trans- mitter, curve. Indicate the units, e.g., Hz, kHz or MHz.

e.g., Frequency Scan, Scan While Track Radar, Monopulse Tracker, AM or FM Communications. ITEM 16 - Pre-emphasis. For frequency or phase modulated transmitters mark the appropriate block to indicate whether ITEM 5 - Tuning Range. Enter the frequency range through which the pre-emphasis is available.

transmitter is capable of being tuned, e.g., 225-400 MHz. For equipment designed to operate only at a single frequency, enter this frequency. ITEM 17 - Deviation Ratio. For frequency or phase modulated Indicate units, e.g., kHz, MHz or GHz. transmitter enter the deviation ratio computed with the formula:

Deviation Ratio = synthesizer or cavity. If the equipment is not readily tunable in the field, ITEM 6 - Method of Tuning. Enter the method of tuning, e.g., crystal, Maximum Frequency Deviation indicate in Item 24, "Remarks," the complexity of tuning. Include Maximum Modulation Frequency

ITEM 18 - Pulse Characteristics. For pulse modulated transmitters:

involved, time required, and location (factory or depot) where equipment is to be tuned.

complexity factors such as skill levels involved, major assemblies

a. Enter the pulse repetition rate in pulses per second (pps).

b. Enter the pulse width at the half voltage levels in microseconds capability. For uniformly spaced channels, enter the center frequency of ITEM 7 - RF Channeling Capability. Describe the RF channeling

(usec).

the first channel and channel spacing e.g., first channel 406 MHz, 100 kHz increments; for continuous tuning, enter the lowest frequency and c. Enter the pulse rise time in microseconds (usec). This is the time the word "continuous;" for others, such as SSB or cases where a duration for the leading edge of the voltage pulse to rise from 10% to channel selection is under software control, enter a detailed description 90% of its peak amplitude.

in Item 24, "Remarks." Any constraints on using any of these channels must be described in Item 24, "Remarks," e.g., degraded channels, d. Enter the pulse fall time in microseconds (usec). This is the time internal hardwiring limitations or lockout capability for frequency hopping duration for the trailing edge of the voltage pulse to fall from 90% to systems. 10% of its peak amplitude.

e. Enter the maximum pulse compression ratio, if applicable.

including the necessary bandwidth for each designator as described in Chapter 9 of the NTIA Manual, e.g., 16K0F3E. For systems with a

ITEM 8 - Emission Designator(s). Enter the emission designator(s)

ITEM 19 - Power. Enter the mean power delivered to the antenna frequency hopping mode as well as a non-hopping mode enter the terminals for all AM and FM emissions, or the peak envelope power emission designators for each mode. Identify each mode as hopping or (PEP) for all other classes of emissions. If there are any unique non-hopping. situations such as interrupted CW, provide details in Item 24, "Remarks." Indicate the units, e.g., W or kW.

ITEM 9 - Frequency Tolerance. Enter the frequency tolerance, i.e., the maximum departure of a transmitter from its assigned frequency after ITEM 20 - Output Device. Enter a description of the device used in normal warm-up time has been allowed. Indicate the units in parts per the transmitter output stage, e.g., ceramic diode, reflex klystron, million (ppm) for all emission types except single sideband which shall transistor or TWT.

be indicated in Hertz (Hz).

ITEM 21 - Harmonic Level. Enter the harmonic level in dB relative ITEM 10 - Filter Employed. Mark the appropriate block. Provide the to the fundamental of the 2nd and 3rd harmonics. Enter in Item c. the characteristics of any filter used in Item 24, "Remarks." relative level in dB of the highest powered harmonic above the 3rd.

ITEM 11 - Spread Spectrum. Mark the appropriate block. If "Yes," see ITEM 22 - Spurious Level. Enter the maximum value of spurious instructions for Item 14. emission in dB relative to the fundamental which occurs outside the

-60 dB point on the transmitter fundamental emission spectrum (Item ITEM 12 - Emission Bandwidth. Enter the emission bandwidths for 12) and does not occur on a harmonic of the fundamental frequency.

which the transmitter is designed at the -3, -20, and -60 dB levels and the occupied bandwidth. The bandwidth at -40 dB shall also be entered ITEM 23 - FCC Type Acceptance No. Enter the FCC type for pulse radar transmitters. The emission bandwidth is defined as that acceptance number if applicable.

appearing at the antenna terminals and includes any significant attenuation contributed by filtering in the output circuit or transmission lines. Values of emission bandwidth specified should be indicated as calculated or measured by marking the appropriate block. Indicate units used, e.g., Hz, kHz or MHz. Note that the Occupied Bandwidth (Item 12.e.) is defined as the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5% of the total mean power radiated.

DD FORM 1494, AUG 96 Transmitter Equipment Characteristics Page (Back)

PAGE

NAME

dBm dB

Kelvin

CLASSIFICATION

RECEIVER EQUIPMENT CHARACTERISTICS

1. MANUFACTURER’S MODEL NO. 2.

10. IF SELECTIVITY

8. DESIGNATOR(S)

16. MAXIMUM BIT RATE

12. IF FREQUENCY

21. REMARKS

CLASSIFICATION

3. INSTALLATION 4. TYPE

5. RANGE 6. OF TUNING

7. CHANNELING CAPABILITY

9. TOLERANCE

11. RF SELECTIVITY (X and complete as applicable)

CALCULATED MEASURED

a. -3 dB

b. -20 dB

c. -60 dB

13. MAXIMUM POST DETECTION FREQUENCY

18. DE-EMPHASIS (X one)

a. YES b. NO

14. MINIMUM POST DETECTION FREQUENCY

a. -3 dB

b. -20 dB

c. -60 dB

19. IMAGE REJECTION

1ST 2ND 3RD

d. PRESELECTION TYPE

a. 1ST

b. 2ND

c. 3RD

15. OSCILLATOR TUNED

a. ABOVE TUNED

FREQUENCY

b. BELOW TUNED

FREQUENCY

c. EITHER ABOVE OR

TUNED FREQUENCY

1ST 2ND 3RD

17. SENSITIVITY

a. SENSITIVITY

b. CRITERIA

c. NOISE FIG

d. NOISE TEMP

20. SPURIOUS REJECTION

NOMENCLATURE, MANUFACTURER’S

EMISSION

RECEIVER RECEIVER

TUNING METHOD

RF

FREQUENCY

BELOW

RECEIVER EQUIPMENT CHARACTERISTICS PAGE

ITEM 1 - Nomenclature, Manufacturer’s Model No. Enter the Government assigned alphanumeric equipment designation. If above is not available, enter the manufacturer’s model number, e.g., MIT 502, and complete Item 2. If above is not available, enter a short descriptive title, e.g., GPS Receiver, Director Station RX.

ITEM 2 - Manufacturer’s Name. Enter the manufacturer’s name if available. If a manufacturer’s model number is listed in Item 1, this item must be completed.

ITEM 3 - Receiver Installation. List specific type(s) of vehicle(s), ship(s), plane(s) or building(s), etc., where the receiver(s) will be installed.

ITEM 4 - Receiver Type. Enter the generic class, e.g., Dual Conversion Superheterodyne or Homodyne.

ITEM 5 - Tuning Range. Enter the frequency range through which the receiver is capable of being tuned, e.g., 225-400 MHz. For equipment designed to operate only at a single frequency, enter this frequency. Indicate units, e.g., kHz, MHz or GHz.

ITEM 6 - Method of Tuning. Enter the method of tuning, e.g., crystal, synthesizer or cavity. If the equipment is not readily tunable in the field, indicate in Item 21, "Remarks," the complexity of tuning.

Include complexity factors such as skill levels involved, major assemblies involved, time required, and location (factory or depot) where equipment is to be tuned.

ITEM 7 - RF Channeling Capability. Describe the RF channeling capability. For uniformly spaced channels, enter the center frequency of the first channel and channel spacing e.g., first channel 406 MHz, 100 kHz increments; for continuous tuning, enter the lowest frequency and the word "continuous;" for others, including cases where channel selection is under software control, enter a detailed description in Item 21, "Remarks."

ITEM 8 - Emission Designator(s). Enter the emission designator(s) including the necessary bandwidth(s) for each designator, e.g., 16K0F3E. For systems with a frequency hopping mode as well as a non-hopping mode enter the emission designators for each mode.

ITEM 9 - Frequency Tolerance. Enter the frequency tolerance, i.e., the maximum departure of a receiver from its assigned frequency after normal warm-up time has been allowed. Indicate the units in parts per million (ppm) for all emission types except single sideband which shall be indicated in Hertz (Hz).

ITEM 10 - IF Selectivity. Enter the bandwidth for each IF stage at the -3, -20 and -60 dB levels. Indicate units, e.g., kHz or MHz.

ITEM 11 - RF Selectivity. Enter the bandwidth at the -3, -20 and -60 dB levels. The RF bandwidth includes any significant attenuation contributed by filtering in the input circuit or transmission line. Values of RF bandwidths specified should be indicated as calculated or measured by marking the appropriate block. Indicate units, e.g., kHz or MHz. Enter the preselection type, e.g., tunable cavity.

ITEM 12 - IF Frequency. Enter the tuned frequency of the first, second and third IF stages. Indicate units, e.g., kHz or MHz.

ITEM 13 - Maximum Post Detection Frequency. Enter the maximum post detection frequency. This is the nominal frequency at the -3 dB point on the high frequency side of the receiver base band. Indicate units, e.g., kHz or MHz.

ITEM 14 - Minimum Post Detection Frequency. For multichannel FM systems enter the minimum post detection frequency. This is the nominal frequency at the -3 dB point on the low frequency side of the receiver base band. Indicate units, e.g., kHz or MHz.

ITEM 15 - Oscillator Tuned. Mark the appropriate block to indicate the location of the 1st, 2nd and 3rd oscillator frequencies with respect to the associated mixer input signal.

ITEM 16 - Maximum Bit Rate. Where applicable, enter the maximum bit rate (bps) that can be used. If spread spectrum is used, enter the bit rate after encoding. Describe any error detecting/correcting codes in Item 21, "Remarks."

ITEM 17 - Sensitivity.

a. Enter the sensitivity in dBm.

b. Specify criteria used, e.g., 12 dB SINAD (Signal to Interference plus Noise and Distortion).

c. If the receiver is used with terrestrial systems, enter the receiver noise figure in dB.

d. If the receiver is used with space or satellite earth stations, enter the receiver noise temperature in Kelvin.

ITEM 18 - De-emphasis. For frequency or phase modulated receivers mark the appropriate block to indicate whether de-emphasis is available.

ITEM 19 - Image Rejection. Enter the image rejection in dB.

Image rejection is the ratio of the image frequency signal level required to produce a specified output, to the desired signal level required to produce the same output.

ITEM 20 - Spurious Rejection. Enter the spurious rejection in dB.

Enter the single level of spurious rejection that the receiver meets or exceeds at all frequencies outside the -60 dB IF bandwidth.

Spurious rejection is the ratio of a particular out-of-band frequency signal level required to produce a specified output, to the desired signal level required to produce the same output.

DD FORM 1494, AUG 96 Receiver Equipment Characteristics Page (Back)

ANTENNA EQUIPMENT CHARACTERISTICS

2. MANUFACTURER’S MODEL NO. 3. NAME

8.

10. REMARKS

CLASSIFICATION

5.4. RANGE

6.

1. a. b. RECEIVING

a. TYPE

b. VERTICAL SCAN

c. HORIZONTAL SCAN

(1) YES (2) NO

a. MAIN BEAM

7. CHARACTERISTICS

(1) MAX ELEV

(2) MIN ELEV

(3) SCAN RATE

b. 1ST MAJOR SIDE LOBE

c. RECEIVING

(1) SECTOR SCANNED

(2) SCAN RATE

9.

a. HORIZONTAL

b. VERTICAL

d. SECTOR BLANKING (X one)

NOMENCLATURE, MANUFACTURER’S

GAIN

TYPEFREQUENCY

POLARIZATION

TRANSMITTING

SCAN

TRANSMITTING AND

BEAMWIDTH

ANTENNA EQUIPMENT CHARACTERISTICS PAGE

ITEM 1 - Function. Mark the appropriate block to indicate the type of function the antenna performs. For multi-antenna system, use one page for each antenna.

ITEM 2 - Nomenclature, Manufacturer’s Model

No. Enter the Government assigned alphanumeric equipment designation. If above is not available, enter the manufacturer’s model number, e.g., DS6558, and complete Item 3. If above is not available, enter a short descriptive title, e.g., ATS-6 telemetry antenna.

ITEM 3 - Manufacturer’s Name. Enter the manufacturer’s name if available. If a manufacturer’s model number is listed in Item 2, this item must be completed.

ITEM 4 - Frequency Range. Enter the range of frequencies for which the antenna is designed.

Indicate units, e.g., kHz or MHz.

ITEM 5 - Type. Enter the generic name or describe general technical features, e.g., Horizontal Log Periodic, Cassegrain with

Polarization Twisting, Whip, Phased Array or

Conformal Array.

ITEM 6 - Polarization. Enter the polarization; if circular, indicate whether it is right or left hand.

ITEM 7 - Scan Characteristics.

a. If this antenna scans, enter the type of scanning, e.g., vertical, horizontal, vertical and horizontal.

b. (1) Enter the maximum elevation angle in degrees (positive or negative referenced to the horizontal) that the antenna can scan.

(2) Enter the minimum elevation angle in degrees (positive or negative referenced to the horizontal) that the antenna can scan.

(3) Enter the vertical scan rate in scans per minute.

c. (1) Enter the angular scanning range in scans per minute.

(2) Enter the horizontal scanning rate in scans per minute.

d. Indicate if antenna is capable of sector blanking. If yes, enter details in item 10, "Remarks."

ITEM 8 - Gain.

a. Enter the maximum gain in dBi.

b. Enter the nominal gain of the first major side lobe of the main beam in dBi and the angular displacement from the main beam in degrees.

ITEM 9 - Beamwidth. Enter the 3 dB beamwidth in degrees.

ITEM 10 - Remarks. Use this item to describe any unusual characteristics of the antenna, particularly as they relate to the assessment of electromagnetic compatibility. Use this item to amplify or clarify any of the information provided above.

DD FORM 1494, AUG 96 Antennar Equipment Characteristics Page (Back)

APPLICATION FOR

SPECTRUM REVIEW

NTIA GENERAL INFORMATION

1. APPLICATION TITLE

2. SYSTEM NOMENCLATURE

3. STAGE OF ALLOCATION (X one)

a. STAGE 1 - CONCEPTUAL b. STAGE 2 - EXPERIMENTAL c. STAGE 3 - DEVELOPMENTAL d. STAGE 4 - OPERATIONAL

4. FREQUENCY REQUIREMENTS

a. FREQUENCY(IES)

b. EMISSION DESIGNATOR(S)

5. PURPOSE OF SYSTEM, OPERATIONAL AND SYSTEM CONCEPTS (WARTIME USE) (X one) a. YES b. NO

6. INFORMATION TRANSFER REQUIREMENTS

7. ESTIMATED INITIAL COST OF THE SYSTEM

8. TARGET DATE FOR

a. APPLICATION APPROVAL b. SYSTEM ACTIVATION c. SYSTEM TERMINATION

9. SYSTEM RELATIONSHIP AND ESSENTIALITY

10. REPLACEMENT INFORMATION

11. RELATED ANALYSIS AND TEST DATA

12. NUMBER OF MOBILE UNITS

13. GEOGRAPHICAL AREA FOR

a. STAGE 2

b. STAGE 3

c. STAGE 4

14. LINE DIAGRAM 15. SPACE SYSTEMS

(See Page(s) (See Page(s)

16. TYPE OF SERVICE(S) FOR STAGE 4 17. STATION CLASS(ES) FOR STAGE 4

18. REMARKS

DOWNGRADING INSTRUCTIONS CLASSIFICATION

NTIA GENERAL INFORMATION PAGE

ITEM 1 - Application Title. Enter the Government nomenclature of the equipment, or the manufacturer’s name and model number, and a short descriptive title.

ITEM 2 - System Nomenclature. Enter the nomenclature of the system for which this equipment is a subsystem, e.g., PATRIOT or Global Positioning System.

ITEM 3 - Stage of Allocation. Mark appropriate block.

ITEM 4 - Frequency Requirements.

a. Enter the required frequency bands. For equipment designed to operate only at a single frequency, enter this frequency. Indicate units, e.g., kHz, MHz, or GHz.

b. Enter the emission designators including the necessary bandwidth for each designator, as described in Chapter 9 of the NTIA Manual e.g., 40M0PON.

Enter in Item 18, "Remarks," any other information pertinent to frequency requirements, such as minimum frequency separation for full duplex links or repeaters; or special relationships involving multiple discrete frequencies.

ITEM 5 - Purpose of System, Operational and System Concepts. Enter a summary description of the function of the system or subsystem, e.g., collect and disseminate meteorological data using satellite techniques;

transmission of radar data for air traffic control; a remote control of ATC radars; provide for the transmission and reception of digital voice and data by means of LOS or tropo modes of propagation; provide navigational signal from which a broad spectrum of users are able to derive navigation data. Also include information on operational and system concepts. Mark whether the system has a wartime function.

ITEM 6 - Information Transfer Requirements. Enter the required character rate, data rates, circuit quality, reliability, etc.

ITEM 7 - Estimated Initial Cost of the System. This item is for information to show the general size and complexity of the system. It is not intended to be a determining factor in system review. For Stage 2 enter research cost, for Stage 3 enter development cost, for Stage 4 enter unit cost of equipment and expected number of equipments/systems to be procured.

ITEM 8 - Target Date. For the stage review requested, enter the appropriate dates. Funds must not be obligated prior to the approval of this application. If foreign coordination is not required, then approximately one year must be allowed for application approval. If foreign coordination is required, approximately two years must be allowed for application approval.

ITEM 9 - System Relationship and Essentiality.

Enter the essentiality and a statement of the relationship between the proposed system and the operational function it is intended to support.

ITEM 10 - Replacement Information. Identify existing system(s) which may be replaced by the proposed system. State any known additional frequency requirements.

ITEM 11 - Related Analysis and/or Test Data. Identify reports that can be made available documenting previous EMC studies, predictions, analyses, or prototype EMC testing that are relevant to the assessment of the system under review.

ITEM 12 - Number of Units. (For mobile systems) - Self explanatory.

ITEM 13 - Geographical Area. Enter geographical location(s) or area(s) of use for this and subsequent stage(s), e.g., Gilfillan Plant, Los Angeles, California, and White Sands Missile Range, New Mexico (Stage 2);

US&P (Stage 3); US&P, NATO Countries and Korea (Stage 4). Provide geographical coordinates (degrees, minutes, seconds) if available.

ITEM 14 - Line Diagram. Enter the page number of the line diagram(s). Attach as another page the line diagram showing the links, direction of transmis- sions, frequency band(s), and associated equipment with J/F 12 numbers.

ITEM 15 - Space Systems. Enter the page number of the space system data. Attach as another page the space system data as described in the NTIA Manual, Paragraph 8.3.7. Data Requirement.

ITEM 16 - Type of Service(s) for Stage 4. Enter the appropriate type of service(s) that applies or will apply to the equipment in the operational stage (Stage 4), as described in Chapter 6, Table of Services, Station Classes, and Stations of the NTIA Manual. If the service is not in accordance with the allocation tables full justification must be entered.

ITEM 17 - Station Class(es) for Stage 4. Enter the appropriate station class(es) as described in Chapter 6 of the NTIA Manual.

DD FORM 1494, AUG 96 NTIA General Information Page (Back) bruce.j.johnson Line bruce.j.johnson Line