ex IRPOD 2.pdf

07/05/2022

ITEM NAMENATIONAL STOCK NUMBER

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5307-01-332-9396 X3 PIN, ROD EYE 20220512135216

NAVAL SEA SYSTEMS COMMAND WASHINGTON DC 501-6603008PC67 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 1RPTR01A

1J836CB1NO0024

TECHNICAL CONTACT

1.0 SCOPE

THE SUBJECT ROD EYE PIN IS ALSO IDENTIFIED AS PIECE 63 ON NAVSHIPS

DRAWING 501-6603009.

THIS IRPOD PROVIDES THE REQUIREMENTS FOR A REPAIR PART CONSISTING

OF ONE PIECE.

2.0 LIST OF APPLICABLE DOCUMENTS

IF A MANUFACTURER QUOTES TO A LATER REVISION OF THE DRAWING (OR CATALOG ITEM) THAN

SPECIFIED BELOW, SUBMITTAL OF QUOTE SHALL INCLUDE TWO (2) COPIES OF THE REVISED

DOCUMENT AND AN EVALUATION OF THE INTERCHANGEABILITY. THE FOLLOWING DOCUMENTS AND

CHANGE DATA ARE APPLICABLE TO THE EXTENT SPECIFIED IN THIS IRPOD, THE DRAWINGS, OR

OTHER DOCUMENTS INVOKED BY THIS IRPOD. CONTRACTING AGENCY APPROVAL IS REQUIRED TO

USE EARLIER SPECIFICATION VERSIONS THAN THOSE LISTED HEREIN, EXCEPT AS IDENTIFIED

BELOW. IF NO DOCUMENT VERSION IS LISTED, THEN ANY VERSION OF THE DOCUMENT MAY BE

USED.

RAW MATERIAL REQUIRED HEREIN MAY HAVE BEEN PROCESSED OR TESTED (FOR EXAMPLE, HEAT

TREATED OR ULTRASONICALLY TESTED) AS REQUIRED BY THE RAW MATERIAL SPECIFICATION

PRIOR TO RECEIPT OF THIS ORDER USING PREVIOUS VERSIONS OF PROCESSING OR TESTING

SPECIFICATIONS. THIS PROCESSING AND TESTING NEED NOT BE REPEATED IF:

1.IT COMPLIED WITH THE APPLICABLE REQUIREMENTS OF THE

PROCESSING/TESTING SPECIFICATION VERSIONS IN EFFECT AT THE TIME OF

THE ACTUAL PROCESSING OR TESTING AND

2.ALL REQUIREMENTS OF THE RAW MATERIAL SPECIFICATION VERSION LISTED

HEREIN HAVE BEEN SATISFIED.

SECTION 6.0 IDENTIFIES SPECIAL REQUIREMENTS FOR SUBMITTAL OF THE PROCEDURES USED

FOR COMPLETED PROCESSING AND TESTING. ALL PROCESSING AND TESTING PERFORMED AFTER

RECEIPT OF THIS ORDER SHALL CONFORM TO THE PROCESSING/TESTING SPECIFICATION

VERSIONS LISTED HEREIN.

DOCUMENT NUMBER VERSION TITLE

MILITARY STANDARDS

+ MIL-STD-129 H, NOT. 1-4 MARKING FOR SHIPMENT AND STORAGE

DRAWINGS

+ 501-6603008

(NOFORN)

J ISOLATION VALVE ASSEMBLY & ARRANGEMENT

+ 501-6603009

(NOFORN)

H ISOLATION VALVE & BRACKET DETAILS

https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J https://nnppweb/web_authoring/adsars/adsars_drawings.asp?DB=KAPL&DwgNo=44230-1-2&Vendor=ALCOP&Rev=J

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5307-01-332-9396 X3 PIN, ROD EYE 20220512135216

NAVAL SEA SYSTEMS COMMAND WASHINGTON DC 501-6603008PC67 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 2RPTR01A

1J836CB1NO0024

TECHNICAL CONTACT

+ LATER VERSIONS (IE: REVISIONS, AMENDMENTS, CHANGE NOTICES

AND/OR INTERIM CHANGES) OF DOCUMENTS IDENTIFIED BY THIS SYMBOL

MAY BE USED IN THE PERFORMANCE OF THE CONTRACT. WHICHEVER

VERSION IS USED MUST BE USED IN ITS ENTIRETY. THE LATER

VERSION MAY BE IDENTIFIED AS "MIL-DTL-" OR "MIL-PRF-" AS

APPLICABLE, WHICH IS EQUIVALENT TO "MIL-#-" (WHERE # IS AN

ALPHA CHARACTER).

3.0 TECHNICAL REQUIREMENTS

3.1 MATERIAL REQUIREMENTS

INTENTIONALLY LEFT BLANK

3.2 MANUFACTURING AND PROCESS REQUIREMENTS

PIN, ROD EYE 501-6603008PC67

THIS ITEM IS TO BE MANUFACTURED IN ACCORDANCE WITH NAVSHIPS

DRAWINGS 501-6603008 AND 501-6603009.

CLEANLINESS REQUIREMENTS:

PART(S) SHALL BE CLEANED BY ANY PROCESS OR COMBINATION OF

PROCESSES WHICH WILL ACCOMPLISH THOROUGH CLEANING WITHOUT

DAMAGE TO THE PART(S). SURFACES SHALL BE EXAMINED VISUALLY

TO DETERMINE FREEDOM FROM DIRT, CORROSION, OIL, GREASE OR

FOREIGN RESIDUE. PRESERVATIVES SHALL NOT BE USED ON PART(S)

WHICH ARE VULNERABLE TO DAMAGE BY CONTACT PRESERVATIVES.

MERCURY CONTAMINATION:THIS ITEM SHALL NOT CONTAIN AND SHALL NOT BE CONTAMINATED BY

MERCURY OR MERCURY COMPOUNDS. THIS REQUIREMENT MUST BE PASSED ON TO ALL

SUBCONTRACTORS. (FOR PROCURING ACTIVITY USE ONLY,INCLUDE MERCURY CONTROL CLAUSE

FROM NAVSEAINST 5100.3 (SERIES)).

4.0 QUALITY ASSURANCE PROVISIONS

PIN, ROD EYE 501-6603008PC67

MILITARY SPECIFICATION MIL-I-45208, AS INVOKED BY NAVSEA DRAWINGS

501-6603008 AND 501-6603009, IS APPLICABLE ONLY TO THE MANUFACTURE

OF THE COMPLETE ISOLATION VALVE AND THOSE VALVE PARTS CONSIDERED

TO BE COMPLEX AND/OR CRITICAL TO THE OPERATION OF THE VALVE, AND

DOES NOT APPLY TO THIS INDIVIDUAL SUBJECT ITEM.

5.0 PREPARATION FOR DELIVERY

PIN, ROD EYE 501-6603008PC67

DRAWING PREPARER/MANUFACTURER

REVISION

MANUFACTURER'S PART NO./DRAWING NO. RSP

ACTIVITY

1H 5307-01-332-9396 X3 PIN, ROD EYE 20220512135216

NAVAL SEA SYSTEMS COMMAND WASHINGTON DC 501-6603008PC67 A

INDIVIDUAL REPAIR PART ORDERING DATA PAGE 3RPTR01A

1J836CB1NO0024

TECHNICAL CONTACT

MARKING REQUIREMENTS:

MARKING AND LABELING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

BAR CODE MARKING SUITABLE FOR HAND SCANNING IS REQUIRED.

IN ADDITION TO THE STANDARD MARKING REQUIREMENTS OF MIL-STD-129,

THE SELLER SHALL INCLUDE THE MANUFACTURER'S COMMERCIAL AND

GOVERNMENT ENTITY (CAGE) CODE AND THE MANUFACTURER'S REFERENCE/

PART NUMBER (MFR/PN) ON INTERMEDIATE AND UNIT PACKS.

PACKAGING AND PACKING REQUIREMENTS:PACKAGING CODES FOR MIL-STD-2073-1 SHALL BE AS

SPECIFIED ELSEWHERE IN THE CONTRACT.

6.0 CONTRACT DATA REQUIREMENTS

INTENTIONALLY LEFT BLANK

6.1 PROCEDURES AND REPORTS

INTENTIONALLY LEFT BLANK

6.2 OTHER CONTRACT DATA REQUIREMENTS

INTENTIONALLY LEFT BLANK