Ex-7 Light Pole Specifications.pdf

LSI Industries Inc. 10000 Alliance Rd. Cincinnati, OH 45242 • (513) 372-3200 • www.lsicorp.com ©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Type : Project : Catalog # :

Date : Prepared By :

Page 1/6 Rev. 07/07/23

Steel Poles Round Tapered

Pole Shaft

• Steel round poles are 4” or 5” in diameter.

• Pole shaft is electro-welded ASTM-A500 Grade C Steel Tubing with a minimum yield strength of 55,000 psi.

• On Tenon Mount steel poles, tenon is high-strength pipe. Tenon N option is 2-3/8” O.D. x 4-3/4” tall.

Hand-Hole

• Standard hand-hole location is 12” above pole base.

• Hand-hole size is 4” x 6” and reinforced.

Base

• Pole base is ASTM-A36 hot-rolled steel plate with a minimum yield strength of 36,000 psi.

• Two-piece square base cover is optional.

Decorative base cover is also available.

Anchor Bolts

• Steel Round Tapered Poles of 11 gauge material are furnished with anchor bolts featuring zinc-plated double nuts and washers. Galvanized anchor bolts are optional

• Poles of 7 gauge material are furnished with galvanized anchor bolts as a standard. Anchor Bolts conform to aSTM F 1554-07a Grade 55 with a minimum yield strength of 55,000 psi

Ground Lug

• Ground lug is standard.

Duplex Receptacle

• Weatherproof duplex receptacle is optional.

Ground Fault Circuit Interrupter

• Self-testing Ground fault circuit interrupter is optional.

Finishes

• Every pole is provided with the DuraGrip

Protection System and a 5-year limited warranty:

• When the top-of-the line DuraGrip Plus Protection System is selected, in addition to the DuraGrip Protection System, a non-porous, automotive-grade corrosion coating is applied to the lower portion of the pole interior sealing and further protecting it from corrosion. This option extends the limited warranty to 7 years.

Determining The Luminaire/Pole Combination For Your Application:

• Select luminaire from luminaire ordering information.

• Select bracket configuration if required

• Determine EPA value from luminaire/ bracket EPA chart

• Select Pole Height

• Select MPH to match wind speed in the application area (See windspeed maps).

• Confirm pole EPA equal to or exceeding value of luminaire/bracket EPA

• Consult factory for special wind load requirements and banner brackets.

Pole Vibration Damper

• A pole vibration damper is recommended in open terrain areas of the country where low steady state winds are common.

• Non-tapered poles and lightly loaded poles are more susceptible to destructive vibration if a damper is not installed.

Listings

• UL Listed

• BAA/TAA Compliant

QUICK LINKS

FEATURES & SPECIFICATIONS

SPEC.1069.C.0323

Exhibit 7 - Light Pole Specifications RTP B5 S11G30 S BLK DGP Plant City Armory

910/19/2023DAL

©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Have questions? Call us at (800) 436-7800

Steel Poles Round Tapered Type :

Page 2/6 Rev. 07/07/23

SPEC.1069.C.0323

1 - See Area Light Brackets - 3” Reduced Drill Pattern and Area Light Brackets - 5” Traditional Drill Pattern Spec Sheets.

2 - Pole heights will have a +/- 1/2” tolerance. Max height for 4RP S10G is 24’ . Max height of the 5RP S11G is 26’

3 - See Flood Lighting Brackets section for choice of FBO Brackets

4 - Only use with 4 inch pole.

5 - For Enterprise, Lexington, and Constitution PT mounting configuration styles, see Tenon Mount (4N) and Lifestyle Slipfit Pole Series

6 - Use with BKA-IFM4

7 - For Enterprise and Lexington D180 or other mounting configuration styles using BK MPT BO accessories order with B3 or B5 drill pattern.

ORDERING GUIDE

TYPICAL ORDER EXAMPLE: RTP B3 S11G 35 S PLP DGP

Pole Series Mounting Method Material Height 2 Mounting Configuration Pole Finish Options

RTP - Round Tapered Pole (New Build)

RTPU - Round Tapered Pole (Retrofit)

Bolt-On Mount1 - See pole selection guide for patterns and fixture matches

B5 - 5” Traditional Drilling Pattern

B3 - 3” Reduced Drilling Pattern

B2 - 2” Reduced Drilling Pattern

T - Tenon Mount - See pole selection guide for tenon and fixture/bracket matches

I - No Mounting Holes1 - Use with:

BKA-IFM4 - Flush Mount Adapter4

Greenlee Lifestyle CH Mounting Style

Enterprise, Lexington, Constitution

PT Single Mounting5

S07G - 07 Ga. Steel

S11G - 11 Ga. Steel

20’

22’

22’ 6”

25’

27’

30’

32’

35’

39’

S – Single/Parallel

D180 – Double

D90 – Double

DN90 – Double

T90 – Triple

TN120 – Triple

Q90 – Quad

QN90 – Quad

N – Tenon Mount (Standard Tenon size is

2-3/8” O.D.)6

4N - Tenon Mount (5RPT only. For 4” poles only, use 4RPI)7

4N-6 - Tenon Mount (5RPT only. For 4” poles use 4RPI)

(Blank) - Use with I for Mounting

Method

BRZ – Bronze

BLK – Black

PLP – Platinum Plus

WHT – White

SVG – Satin Verde Green

GPT – Graphite

MSV – Metallic Silver

BZA – Alternate Bronze

GA – Galvanized Anchor Bolts

SF – Single Flood3

DF – Double Flood 3

DGP – DuraGrip® Plus

LAB – Less Anchor Bolts

CRXX - Conduit Raceway4

Need more information?

Click here for our glossary

Have additional questions?

Call us at (800) 436-7800

ACCESSORY ORDERING INFORMATION

Part Number Description

158388CLR 20 SRTBC Square Based Cover (for 20’ RTP Poles)

162961CLR 25 SRTBC Square Based Cover (for 22’, 22’ 6”, and 25’ RTP Poles)

497836CLR 30 SRTBC Square Based Cover (for 27’ and 30’ RTP Poles)

158554CLR 35 SRTBC Square Based Cover (for 32’ and 35’ RTP Poles)

433035CLR 39 SRTBC Square Based Cover (for 39’ RTP Poles)

132336 MH5 - mounting Hole Plugs for use with 5” traditional drill pattern (3 set of 3 plugs)

681126 MH3 - mounting Hole Plugs for use with 3” reduced drill pattern (3 sets of 3 plugs)

725841 MH2 - Mounting Hole Plugs for use with 2" reduced drill pattern (3 sets of 3 plugs)

725841 MH2 - Mounting Hole Plugs for use with 2” reduced drill pattern (3 sets of 3 plugs)

122568CLR ER2 – Weatherproof RTP Duplex Receptacle

122569CLR GFI – Ground Fault RTP Circuit Interrupter

ANCHOR BOLT KIT ORDERING INFORMATION

Part Number Description

AB KIT 122588 RTP 20’/25’/30’ S11G (Steel Plated)

AB KIT 122589 RTP 35’/39’ S11G (Steel Plated)

AB KIT 122613 RTP 20’/25’/30’ S11G (Galvanized)

AB KIT 1226140 RTP 35’/39’ S11G (Galvanized)

AB KIT 122615 RTP 39’ S07G (Galvanized)

RTPP - Round Tapered Pole (New Build)

B5 5 - 5” Traditional Drilling Pattern

S11G G - 11 Ga. Steel

30’

SSS – Single/Parallel

BLKK – BlackK

DGPP – DuraGripP p®p® Plus

AB KIT 122588 RTP 20’/25’/30’ S11G (Steel Plated)

30 SRTBC Square Based Cover (for 27’ and 30’ RTP Poles)497836CLR

Back to Quick Links

©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Have questions? Call us at (800) 436-7800

Steel Poles Round Tapered

Page 3/6 Rev. 07/07/23

SPEC.1069.C.0323

Type :

DRILLING LOCATIONS

Side “B”Side “D”

Side “C” Sides A B C D

Hand-hole X Single X D180 X X D90 X X

DN901

T90 X X X

TN1202 X

Q90 X X X X

QN903

Single FBO X

Double FBO X X

1 - Two locations will be 45° to the left and right of Side A.

2 - Other two locations will be 120° to the left and right of Side A.

3 - Two locations will be 45° to the left and right of Side A and two locations will be 135° to the left and right of Side A.

Consult factory for custom variations. Standard SF and DF pole preparations are located 3/4 of the height of the pole from the base, except on 20’ poles. Maximum height for SF and DF pole preparations on 20’ poles is 13’ from the base.

FIXTURE CONFIGURATIONS

Single D90 DN90 Parallel T90 TN120 QN90 Q90D180

©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Have questions? Call us at (800) 436-7800

Steel Poles Round Tapered

Page 4/6 Rev. 07/07/23

SPEC.1069.C.0323

Type :

BOLT CIRCLE

Note: Base plate illustrations may change without notice. Do not use for setting anchor bolts. Consult factory for the appropriate anchor bolt template.

Bolt Circle

Anchor Bolt Size

Anchor Bolt Projection

Base Plate Dimensions

Pole Gauge

N SQ

10-1/8" (257mm) sq.

Bolt Holes

Bolt Circle

0° Handhole

12" (305mm) sq. 12" (305mm) sq.

12" (305mm) Dia.

Bolt Circle

12" (305mm) Dia.

Bolt Circle

11" (279mm) Dia.

Bolt Circle

1"x30"

(25mm x 762mm)

4" (102mm)

10-1/8" sq. x 1" thk.

(257mm x 25mm)

Slotted 11" (279mm)

4" (102mm)

12" sq. x 1" thk.

(305mm x 25mm)

12" (305mm)

1-1/4" x 42"

(32mm x 1067mm)

5" (127mm)

12" sq. x 1-1/4" thk.

(305mm x 32mm)

7 (39’ only)

Slotted 12" (305mm)

Bolt Holes

Bolt Circle

0° Handhole

Bolt Holes

Bolt Circle

0° Handhole

Bolt Circle Designator

STANDARD BASEPLATE

Note: Base plate illustrations may change without notice. Do not use for setting anchor bolts. Consult factory for the appropriate anchor bolt template.

Bolt Circle

Anchor Bolt Size

Anchor Bolt Projection

Base Plate Opening for Wireway Entry

Base Plate Dimensions

Pole Gauge

T YV

20' RTPU

9-7/8" (251mm) sq.

25' RTPU

11-1/4" (286mm) sq.

30' RTPU

12" (305mm) sq.

35' RTPU

12-1/8" (308mm) sq.

39' RTPU

13" (330mm) sq.

39' RTPU

14-3/8" (365mm) sq.

14" (356mm) Dia. Bolt Circle

16" (406mm) Dia. Bolt Circle

11" (279mm) Dia. Bolt Circle

Slotted 8-1/2" - 11" (216mm-279mm)

1"x30" (25mm x 762mm)

4" (102mm)

5-9/10" (150mm)

9-7/8" sq. x 1" thk.

(251mm x 25mm)

Slotted 9" - 13" (229mm-330mm)

1"x30" (25mm x 762mm)

4" (102mm)

6-7/10" (171mm)

11-1/4" sq. x 1" thk.

(286mm x 25mm)

4" (102mm)

7-5/8" (194mm)

12" sq. x 1" thk.

(305mm x 25mm)

11" - 13-1/2" (279mm-343mm)

1-1/4" x 42"

(32mm x 1067mm)

5" (127mm)

9-1/8" (232mm)

14-3/8" sq. x 1-1/4" thk.

(365mm x 32mm)

7 (39' Only)

Slotted 12" - 16" (305mm-406mm)

U

13" (330mm) Dia. Bolt Circle

Slotted 10" - 14" (254mm-356mm)

W

13-1/2" (343mm) Dia. Bolt Circle

4" (102mm)

8-5/8" (219mm)

12-1/8" sq. x 1" thk.

(308mm x 25mm)

X

14-1/2" (368mm) Dia. Bolt Circle

4" (102mm)

9-1/8" (232mm)

13" sq. x 1" thk.

(330mm x 25mm)

Slotted 11-1/2" - 14-1/2" (292mm-368mm)

Bolt Circle Designator

UNIVERSAL BASEPLATE

©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Have questions? Call us at (800) 436-7800

Steel Poles Round Tapered

Page 5/6 Rev. 07/07/23

SPEC.1069.C.0323

Type :

PRODUCT DIMENSIONS

Pr oj ec ti on

20'-39' (6.1m - 11.9m)

Optional

Base

Cover

ONE-PIECE RTPT –

Hand-hole

(4) Anchor Bolts

Foundation By Other

12" (305mm) Standard

SF –

Single Flood

Pole Preparation

Height Pole Bottom Pole Top

20' (6.1m)

22' (6.1m)

25' (7.1m)

27' (8.2m)

30' (9.1m)

32' (9.7m)

35' (10.7m)

39' (11.9m)

ONE-PIECE SHAFT

5.80" (147mm)O.D.

6.60" (168mm)O.D.

6.60" (168mm)O.D.

7.50" (191mm)O.D.

7.50" (191mm)O.D.

8.50" (216mm)O.D.

8.50" (216mm)O.D.

9.00" (229mm)O.D.

3.00" (76mm)O.D.

3.52" (89mm)O.D.

3.10" (79mm)O.D.

3.72" (94mm)O.D.

3.30" (84mm)O.D.

4.02" (102mm)O.D.

3.60" (91mm)O.D.

3.54" (90mm)O.D.

N = 2-3/8" (60mm) O.D. x 4-3/4" (121mm) Tenon

Bolt-On Mount 2-Bolt Pattern

B2

2.50

1.00

1.00

0.40

0.75

0.40

TOP OF POLE

CL

B3

TOP OF POLE

CL

3.50

2.41

MAX

1.79

MIN

1.05

2.10

0.63

0.56

B5

TOP OF PO

CL

0.563

0.750

0.563

©LSI Industries Inc. All Rights Reserved. Specifi cations and dimensions subject to industry standard tolerances. Specifi cations subject to change without notice.

Have questions? Call us at (800) 436-7800

Steel Poles Round Tapered

Page 6/6 Rev. 07/07/23

SPEC.1069.C.0323

Type :

WIND SPEED

EPA Information All LSI Industries’ poles are guaranteed to meet the EPA requirements listed. LSI Industries is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located.

CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. LSI Industries cannot accept responsibility for harm or damage caused in these situations.

NOTE: Pole calculations include a 1.3 gust factor over steady wind velocity. Example: poles designed to withstand 80 MPH steady wind will withstand gusts to 104 MPH. EPAs are for locations 100 miles away from hurricane ocean lines. Consult LSI for other areas. Note: Hurricane ocean lines are the Atlantic and Gulf of Mexico coastal areas. For applications in Florida or Canada, consult factory.

Use ONLY with “Wind Speed Map for ASCE 7-10

All LSI Industries’ poles are guaranteed to meet the EPA requirements listed. LSI Industries is not responsible if a pole order has a lower EPA rating than the indicated wind-loading zone where the pole will be located.

CAUTION: This guarantee does not apply if the pole/bracket/fixture combination is used to support any other items such as flags, pennants, or signs, which would add stress to the pole. LSI Industries cannot accept responsibility for harm or damage caused in these situations.

Note:

1- Poles shorter than these listed here in for each gauge have EPA rating equal to or greater than what is provided in this table. To Confirm EPA ratings on shorter poles, contact LSI Industries.

POLE1 Mtg. Height Length

(ft) Wall Thick (ga)

BOLT CIRCLE EPA

Designator Dia. (in) Anchor bolt Dia (in) 110 MPH 115 MPH 120 MPH 130 MPH 140 MPH 150 MPH 160 MPH 170 MPH 180 MPH

11-ga x 20’ 20 11 N 11 1.00 14.5 13.1 12.0 10.0 8.5 7.3 6.3 5.5 4.8

11-ga x 22’ 22 11 N 11 1.00 16.6 15.0 13.8 11.6 9.8 8.4 7.3 6.4 5.6

11-ga x 25’ 25 11 N 11 1.00 13.1 12.0 10.9 9.0 7.6 6.5 5.6 4.9 4.2

11-ga x 27’ 27 11 N 11 1.00 15.2 13.8 12.5 10.5 8.8 7.6 6.5 5.7 5.0

11-ga x 30’ 30 11 N 11 1.00 12.3 11.1 10.1 8.4 7.0 6.0 5.1 4.4 3.8

11-ga x 32’ 32 11 Q 12 1.00 12.3 11.1 10.1 8.4 7.0 6.0 5.1 4.4 3.8

11-ga x 35’ 35 11 Q 12 1.00 10.1 9.1 8.2 6.7 5.6 4.7 3.9 3.4 2.9

11-ga x 39’ 39 11 Q 12 1.00 7.6 6.8 6.1 4.9 4.0 3.3 2.7 2.3 1.9

7-ga x 39’ 39 7 S 12 1.25 10.2 9.1 8.2 6.7 5.6 4.7 3.9 3.3 2.8