ESBD_518881_1779308628424_4_Attachment F 304T-26-445A1 Tools.pdf

*Based on TxDOT specification No. 445-79-67906. Dated April 2025

Texas Comptroller of Public Accounts

Statewide Procurement Division

IFB No. 304T-26-445A1

Master Tool Sets and Individual Tools

Attachment F

Requirements and Specifications

RFP No. 304T-26-445A1 Master Tool Sets and Replacement Tools

NOTICE: Any example shown is listed to show type and class of equipment desired.

Respondents are cautioned to read the Specification carefully, as there may be special requirements not commonly offered by the equipment manufacturer. DO NOT ASSUME THE

EXAMPLES LISTED MEET ALL OF THE DETAILED SPECIFICATION REQUIREMENTS

MERELY BECAUSE IT IS LISTED AS AN EXAMPLE.

Line 1: Master Tool Set Reference Manufacturer/Brand or CPA Approved Equal: Snap-on Tools U.S. Set 6, Part No.

9600GSBO, Mac Tools AUTOMASTERPRO

Function and Design Requirements: This specification describes a master tool set, minimum of 1,152 pieces, consisting of U.S. and metric components used for garage and fleet maintenance and repair.

Each tool set shall include (but not limited to):

1. Hand Tools: Each master tool set must include, but not be limited to, the following types of hand tools:

A. Drive Tools, Minimum 315 pieces:

1. 6pt High Drive Standard and Impact Sockets, Shallow and Deep

a) Reference Brand or CPA Approved Equal: Snap On Flank Drive, Mac RBRT

b) SAE and Metric

c) 1/4”, 3/8”, 1/2” Sockets

d) Standard Sockets - Chrome Finish

e) Impact Sockets - Black Oxide Finish

2. Hex Bit Standard Sockets, Minimum 25 pieces:

a) SAE and Metric

b) 1/4” and 3/8” Sockets

c) Chrome Finish

3. Star Bit Drive Sockets, Minimum 12 pieces:

a) Reference Brand or CPA Approved Equal: Torx

b) 3/8” and 1/4” Sockets

c) To include but not limited to: T8, T10, T15, T20, T25, T27, T30, T40, T45, T47, T50, T55

d) Chrome Finish

4. Master Screwdriver Bit Set, Minimum 37 pieces:

a) Reference Brand or CPA Approved Equal: Snap-On SDM400A

b) To include but not limited to: SAE shank bits, adaptors and storage case.

5. Extensions and Adapters, Minimum 43 pieces:

a) Extensions shall include but not limited to: friction ball, friction ball wobble plus, and knurled friction ball extensions

b) Adapters shall include but not limited to: square drive adapters, universal joints

c) 1/4”, 3/8” and 1/2“

d) Chrome Finish

B. Wrenches, Minimum 197 pieces:

1. Shall include but not limited to the following types of wrenches:

a) Box

b) Combination

c) Crowfoot

d) Extended

e) Flank drive or equivalent

f) Hex

g) Line

h) Locking

i) Open-end/flare

j) Ratchet

2. SAE and Metric

3. Chrome Finish

C. Ratchet Torque Wrench (SAE), Minimum 2 pieces:

1. 20-100 ft-lb and 50-250 ft-lb

2. Must have certificate of calibration

3. Chrome Finish

D. Screwdrivers: Phillips, Flat, Combination, Ratcheting, Minimum 36 pieces:

1. Standard, Long, and Miniature Sized

2. Chrome Finish

E. Rethreading/Tap and Die Sets, SAE and Metric with Storage Case, Minimum 3 sets [Tap and Die Sets: 41 pieces each (SAE and Metric), Rethreading/Tap and Die Sets: 48 Pieces]:

1. Reference Brands or CPA Approved Equal:

a) SAE Tap and Die Set: Snap-On TD2425A

b) Metric Tap and Die Set: Snap-On TDM117B

c) Master Rethreading Tap and Die Set: Snap-On RTD48

2. Shall include range of tap wrenches, die stocks, thread gauges and exclusive die sockets.

3. SAE:

a) 4–40 to 12–24 Machine;

b) 1/4"-28 NF to 1/2"-20 NF; and

c) 1/4"-20 NC to 1/2"-13 NC

4. Metric: M3-0.5 to M12-1.7

5. High Speed Steel (HSS)

6. Carbon Steel or equivalent in quality and durability

F. Awls, Hooks, and Picks, Minimum 6 pieces:

1. Shall be constructed of material that ensures optimum strength and durability

G. Prybars, Minimum 8 pieces:

1. Shall include but not limited to: Regular and Striking

2. Shall be constructed of material that ensures optimum strength and durability

H. Pliers, Minimum 27 pieces:

1. Shall include but not limited to: Cutting, Locking, Needle Nose, Adjustable, Snap Ring, Special Purpose

2. Must be constructed of materials that ensures optimum strength and durability.

I. Pullers, Minimum 105 pieces:

1. Reference Brands or CPA Approved Equal:

a) Bolt Grip Puller Set: Snap-On CJ2001P

b) Gear Puller Set: Snap-On CJ2002

c) Rear Axle Puller Set: Snap-On CJ2003A

d) Interchangeable Puller Set: Snap-On CJ2004

e) Master Interchangeable Puller Set: Snap-On CJ2005

2. All components must be constructed of material that ensures optimum strength and durability.

J. Punches and Chisels, Minimum 31 pieces:

1. Shall be constructed of material that ensures optimum strength and durability

2. Must include but not limited to: bronze tapered punches, pin, starter, and center punches and flat chisels

K. Hammers, Minimum 9 pieces:

1. To include but not limited to: Soft Face, Ball Peen, Bronze Tip, Plastic Tip

2. Shall be constructed of material that ensures optimum strength and durability.

L. Drill Bits, Minimum 29 pieces:

1. Reference Brand or CPA Approved Equal: Snap-On DBTR129

2. Sizes to include but not limited to: 1/16 – 1/2” 135° split point and mechanics length three flat shank.

3. Cobalt or Titanium Finish

4. High Speed Steel (HSS)

M. Tubing & Double Flaring Set and Constant Tension Cutter, Minimum 1 set (48 pieces) and Micro Tension Cutter:

1. Reference Brand or CPA Approved Equal:

a) Tubing & Double Flaring Set: Snap-On TF528D

b) Micro Tension Cutter: Snap-On TCCTMIC

2. Set shall include but not limited to: Flaring bar, rod handle, yoke, tubing cutter, and hard storage case

3. Additional Micro Tension Cutter

4. 3/16”, 1/4”, 5/16”, 3/8” and 1/2”

N. Files, Handles, and Hacksaws, Minimum 14 pieces:

1. Files – to include but not limited to: Three Square, Bastard Cut, Miniature

2. Handles – must be compatible with Bastard Cut files above

3. Hacksaw – Reference Brand or CPA Approved Equal: Snap-On HSG319

O. Cleaning Supplies, Minimum 8 pieces:

1. Shall include but not limited to: Blow Guns, Brushes, Scrapers, Terminal Cleaners

P. Miscellaneous, Minimum 32 pieces:

1. Shall include but not limited to: Crimps, Gauge Sets, Circuit Testers, Broken Screw

Extractor Sets (25 Pieces)

2. Power Tools, Minimum 6 pieces:

A. Shall operate off of 90 to 120 PSI range.

1. Must Include but not limited to:

a) 1/4” Mini Air Ratchet

b) 3/8” Air Impact

c) 1/2” Air Impact

d) 3/8” Air Ratchet

e) 3/8” Reversible Air Drill

f) 1/2” Reversible Air Drill

3. Storage and Organization: Each master tool set must include a roll cab and tool chest for storage as well as foam/shadow board organization options for all provided tools including tool management and identification. Tool storage cabinet shall include rolled edges for safety and durability and be equipped with a locking mechanism to prevent drawer movement while the cabinet is in transit.

4. Shop and Safety Equipment, Minimum 32 pieces:

A. Each master tool set shall include but not be limited to:

1. Creeper Seats

2. KN95 Masks (20 piece)

3. Technician Gloves (Large)

4. Ear Protection

5. Goggles

6. Extendable Mirror

7. Magnetic Pick Up Tool

8. Utility Knife

9. Tape Measures (12 Foot)

10. Mechanics Stethoscope

Lines 2-5: Discount Offered for Individual Tools CPA is requesting an overall discount from manufacturer pricing for the following tool categories:

Line 2: Hand Tools Line 3: Power Tools (Including Battery Powered, Air Powered, and Corded Electric) Line 4: Diagnostic Tools Line 5: Storage Solutions

Respondents shall include with their Response:

1. Itemized listing of each category of tools.

2. Discounts shall be offered as entered on the Mandatory Price Sheet.