21.10902.08 | TFC CAPITOL COMPLEX AGENCY FURNITURE STANDARD AUGUST 26, 2025

PACKAGE B |TFC AGENCIES

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

TFC Capitol Complex Capitol Complex Expansion

Package B: Agency Furniture

PACKAGE B

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

PO-1

TYPICAL PRIVATE OFFICE – 6’ x 7’- 8"

B C D

Provide line- item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

Dual Monitor Arm - include one (1) dual monitor arm per private office.

Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

Fixed Worksurface

• 30”x60” fixed work surface located at work wall

• Woodgrain Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

• Mitered Edge

Fixed Return Worksurface:

• 30”x72” fixed desk with open, loop or closed leg –

Woodgrain Plastic Laminate with modesty panel.

• Mitered Edge

Worksurface Power:

• Provide leg access/vertical cable management (if applicable) and/or cable management trough under worksurface as needed; provide grommets as needed

• Provide surge protector (6’-0” cord) and worksurface power module for convenience (non-dedicated circuit) power access

• Assume the following power/data requirements for each

Private Office:

• (4) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and

(1) Type C USB ports and (2) electrical sockets

(described above)

• All Power/Data to be verified with client.

Tackable Acoustic Fabric-Wrapped Panel:

• Provide at work wall above worksurface – height to align with top of storage componentry. Assume Grade 3 and must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Woodlook Laminate Wall Panel

• Provide at work wall above worksurface – height to align with top of storage componentry.

• Provide (2) matching shelves. Matching ABS/thermo-plastic edge or similar.

• *Manufacturer to confirm weight capacity.

WOODGRAIN

LAMINATE WORK

SURFACE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

TACKABLE FABRIC PANELS

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

MODESTY PANEL

B Worksurface Tops: HPL/TFL Plastic Laminate – Wilsonart Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

Storage Components, Modesty Panel, Base, Shelves, Wall Panel:

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

Finishes

Line-item Pricing

MONITOR

WOODGRAIN

LAMINATE

MITERED EDGE

5' -0

2' -6

6'-0"

2'-6"

7' -8

MONITOR

TACKABLE

FABRIC PANELS

WOODGRAIN

LAMINATE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

MODESTY PANEL

MITERED EDGE

WOODGRAIN

LAMINATE

WORK SURFACE

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

PO-2

TYPICAL EXECUTIVE OFFICE – 8 x 9’-6”

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

Dual Monitor Arm - include one (1) dual monitor arm per private office. Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

Fixed Worksurface

• 30”x66” fixed work surface located at work wall

• Woodgrain Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

• Mitered Edge

Fixed Return Worksurface:

• 30”x96” rectangular fixed desk with open, loop or closed leg –

Woodgrain Plastic Laminate with full modesty panel.

• Mitered Edge

Worksurface Power:

• Provide leg access/vertical cable management (if applicable) and/or cable management trough under worksurface as needed;

provide grommets as needed

• Provide surge protector (6’-0” cord) and worksurface power module for convenience (non-dedicated circuit) power access

• Assume the following power/data requirements for each Private

Office:

• (4) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• All Power/Data to be verified with client.

Storage Components - Wardrobe tower with box/box/file storage

• One (1) lateral drawer file cabinet with white plastic laminate drawers with full pull out.

• One (1) +/- 50” H wardrobe tower, slate grey laminate finish.

Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• Random Keying on locks

• Body/Face of all storage components to be Woodgrain Plastic

Laminate with white laminate drawers with full pull out.

• Parallel Bar Pulls

• Tackable Acoustic Fabric-Wrapped Panel:

• Provide at work wall above worksurface – height to align with top of storage componentry. Assume Grade 3 and must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

WARDROBE TOWER –

WOODGRAIN

LAMINATE

B Worksurface Tops: HPL/TFL Plastic Laminate – Wilsonart Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

Wardrobe + Storage Components, Modesty Panel, Base, Shelves, Wall Panel

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

FULL MODESTY PANEL

WOODGRAIN

LAMINATE

B C D

Wood Look Laminate Wall Panel:

• Provide at work wall above worksurface – height to align with top of storage componentry. Provide (3) matching shelves.

• *Manufacturer to confirm weight capacity.

• ABS/thermo-plastic edge or similar.

WOODGRAIN

LAMINATE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

TACKABLE FABRIC PANELS

MONITOR

Finishes

Line-item Pricing

MITERED EDGE

8'-0" 9'

-6

1' -3

5'

-6

2' -6

MONITOR

TACKABLE

FABRIC PANELS

WOODGRAIN

LAMINATE

MODESTY PANEL

MITERED EDGE

WOODGRAIN

LAMINATE

WORK SURFACE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

WARDROBE

TOWER -

WOODGRAIN

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

PO-3

TYPICAL EXECUTIVE OFFICE – 6’ x 10’

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

Dual Monitor Arm - include one (1) dual monitor arm per private office. Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

B Worksurface Tops: HPL/TFL Plastic Laminate – Wilsonart Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

Wardrobe + Storage Components, Base, Shelves, Wall Panel

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

Fixed Worksurface

• 30”x66” fixed work surface located at work wall

• Woodgrain Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

• Mitered Edges

Fixed Return Worksurface:

• 30”x72” fixed desk with open, loop or closed leg – Woodgrain

Plastic Laminate with modesty panel.

• Mitered Edges

Worksurface Power:

• Provide leg access/vertical cable management (if applicable) and/or cable management trough under worksurface as needed;

provide grommets as needed

• Provide surge protector (6’-0” cord) and worksurface power module for convenience (non-dedicated circuit) power access

• Assume the following power/data requirements for each Private

Office:

• (4) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• All Power/Data to be verified with client.

Dual Monitor Arm - include one (1) dual monitor arm per private office.

Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

Storage Components – Wardrobe/open shelf tower with file/file lower storage

• One (1) lateral drawer file cabinet with white plastic laminate drawers with full pull out, (3) equal open shelf cubbies

• Random Keying on locks

• Body/Face of all storage components to be Woodgrain Plastic

Laminate with white plastic laminate drawers w/ full pull out.

• Parallel Bar Pulls – Warm grey or Similar

Tackable Acoustic Fabric-Wrapped Panel:

Provide at work wall above worksurface – height to align with top of storage componentry. Assume Grade 3 and must have a minimum abrasion of

Wyzenbeek 100,000 double rubs.

Wood look Laminate Wall Panel

• Provide at work wall above worksurface – height to align with top of storage componentry. ABS/thermo-plastic edge or similar.

• Provide (1) panel hung shelf.

• *Manufacturer to confirm weight capacity.

WOODGRAIN

LAMINATE

WARDROBE TOWER +

LOCKABLE FILE/ FILE LOWER

STORAGE WOODGRAIN

LAMINATE

(3) OPEN CUBBIES TACKABLE FABRIC

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

B C D

Finishes

Line-item Pricing

MONITOR

5' -5

6'-0"

2' -0

'-0

2'-6"

MONITOR

TACKABLE FABRIC PANELS

MODESTY PANEL

WOODGRAIN

LAMINATE

WORK SURFACE

(3) OPEN CUBBIES

WARDROBE TOWER+

LOCKABLE FILE/FILE LOWER

STORAGE WOODGRAIN

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

PO-4

TYPICAL EXECUTIVE OFFICE – 8’ x 10’

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

B Worksurface Tops: HPL/TFL Plastic Laminate – Wilsonart Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge, Shelves

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

Fixed Worksurface

• 30”x66” fixed rectangular work surface located at work wall

• Woodgrain Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Fixed Return Worksurface:

• 30”x96” fixed rectangular desk with open, loop or closed leg –

Woodgrain Plastic Laminate with modesty panel.

Worksurface Power:

• Provide leg access/vertical cable management (if applicable) and/or cable management trough under worksurface as needed;

provide grommets as needed

• Provide surge protector (6’-0” cord) and worksurface power module for convenience (non-dedicated circuit) power access

• Assume the following power/data requirements for each Private

Office:

• (4) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• All Power/Data to be verified with client.

Dual Monitor Arm - include one (1) dual monitor arm per private office.

Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

Storage Components – Double door wardrobe with file drawer lower storage

• One (1) lockable lateral drawer file cabinet with white plastic laminate drawers with full pull out.

• One (1) +/- 50” H wardrobe tower, woodgrain laminate finish.

Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• Random Keying on locks.

• Body/Face of all storage components to be Woodgrain Plastic

Laminate with white plastic laminate drawers w/ full pull out.

• Parallel Bar Pulls – Warm grey or Similar

Tackable Acoustic Fabric-Wrapped Panel:

• Provide at work wall above worksurface – height to align with top of storage componentry. Assume Grade 3 and must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Woodlook Laminate Wall Panel

• Provide at work wall above worksurface – height to align with top of storage componentry. Provide (3) matching shelves.

• *Manufacturer to confirm weight capacity.

• ABS/thermo-plastic edge or similar.

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

WOODGRAIN

LAMINATE

DOUBLE DOOR WARDROBE

TOWER + LOCKABLE FILE

LOWER STORAGE-

WOODGRAIN LAMINATE

TACKABLE FABRIC

B C D

Finishes

Line-item Pricing

MODESTY

PANEL

MONITOR

5' -5

8'-0"

'-0

2' -0

2'-6"

MONITOR

TACKABLE

FABRIC PANELS

MODESTY PANEL

DOUBLE DOOR WARDROBE

TOWER+ LOCKABLE FILE

LOWER STORAGE -

WOODGRAIN LAMINATE

WOODGRAIN

LAMINATE WORK

SURFACE

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

PO-5

TYPICAL PRIVATE OFFICE – 6’ x 6’

B C D

Provide line- item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

Dual Monitor Arm - include one (1) dual monitor arm per private office.

Single mount preferred with fully-articulating arms to allow screens to turn for collaboration.

Fixed Worksurface

• 30”x60” fixed work surface located at work wall

• Woodgrain Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

• Mitered Edge

Fixed Return Worksurface:

• 30”x42” fixed desk with open, loop or closed leg –

Woodgrain Plastic Laminate with modesty panel.

• Mitered Edge

Worksurface Power:

• Provide leg access/vertical cable management (if applicable) and/or cable management trough under worksurface as needed; provide grommets as needed

• Provide surge protector (6’-0” cord) and worksurface power module for convenience (non-dedicated circuit) power access

• Assume the following power/data requirements for each

Private Office:

• (4) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and

(1) Type C USB ports and (2) electrical sockets

(described above)

• All Power/Data to be verified with client.

Tackable Acoustic Fabric-Wrapped Panel:

• Provide at work wall above worksurface – height to align with top of storage componentry. Assume Grade 3 and must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Woodlook Laminate Wall Panel

• Provide at work wall above worksurface – height to align with top of storage componentry.

• Provide (2) matching shelves. Matching ABS/thermo-plastic edge or similar.

• *Manufacturer to confirm weight capacity.

WOODGRAIN

LAMINATE WORK

SURFACE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

TACKABLE FABRIC PANELS

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

MODESTY PANEL

B Worksurface Tops: HPL/TFL Plastic Laminate – Wilsonart Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

Storage Components, Modesty Panel, Base, Shelves, Wall Panel:

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

Finishes

Line-item Pricing

MONITOR

WOODGRAIN

LAMINATE

MITERED EDGE

2'-6"

5' -0

2' -6

6'-0" 7'

-8

4' -0

1' -1

0" 6'

-0

Fixed Worksurface

• 22”x72” fixed work surface located at work wall

• Woodgrain Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

• Mitered Edge

Fixed Return Worksurface:

• 30”x48” fixed desk with open, loop or closed leg –

Woodgrain Plastic Laminate with modesty panel.

• Mitered Edge

MONITOR

TACKABLE

FABRIC PANELS

WOODGRAIN

LAMINATE

WOODGRAIN

LAMINATE PANEL

W/ MATCHING

SHELVES

MODESTY PANEL

MITERED EDGE

WOODGRAIN

WORK SURFACE

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-1

TYPICAL STAFF WORKSTATION – 5’ x 5’

A Worksurface Tops: HPL/TFL Frosty white laminate

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Panel Shelf, Base + Wall Panel :

HPL/TFL Woodgrain laminate Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

E Storage Componentry: HPL/TFL slate gray plastic laminate or similar. *Line item

F Mobile Pedestal Cushion: Momentum Deka Rain or similar. *Line item

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

One (1) mobile box/ file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

• Mobile Pedestal Cushion: Assume Grade C or Grade III fabric allowance on cushion fabric.

• Black casters

Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

10”H frosted acrylic stacker panels with eased edges.

Fixed Worksurface

• One (1) 30”x56” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) 18” x 27” fixed rectangular return worksurface at desk height

• One (1) shared shelf mounted on panel at spline.

*Manufacturer to confirm weight capacity.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs.

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

FROSTY WHITE

LAMINATE

ACOUSTICAL FABRIC-WRAPPED

MODESTY/PRIVACY PANEL

*LINE ITEM - MOBILE BOX/FILE

PEDESTAL –

LAMINATE (SLATE GREY)

WOODGRAIN

LAMINATE

BA C D E F

SHARED SHELF –

WOODGRAIN

LAMINATE

Finishes

Line-item Pricing

WOODGRAIN

LAMINATE

MONITOR

1' -5

5' -0

5'-0"

2'-6"

2'-3"

4' -8

1' -5

5' -0

5'-0"

2'-6"

2'-3"

4' -8

FROSTY WHITE

LAMINATE

MONITOR

ACOUSTICAL FABRIC-WRAPPED

MODEST/PRIVACY PANEL

WOODGRAIN

LAMINATE

SHARED SHELF -

WOODGRAIN

LAMINATE

WOODGRAIN

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-2

TYPICAL STAFF WORKSTATION – 6’ x 6’

FROSTY WHITE

LAMINATE

A Worksurface Tops: HPL/TFL Plastic Laminate - Frosty White

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Base + Wall Panel: HPL/TFL Woodgrain laminate Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey or similar

E Pedestal to be HPL/TFL slate gray plastic laminate or similar

F Mobile Pedestal Cushion: Momentum Deka Rain or similar.

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

One (1) fixed box/box file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

10”H frosted acrylic stacker panels with eased edges.

Fixed Worksurface

• 30”x48” fixed rectangular work surface located at work wall

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) 30” D fixed rectangular worksurface at desk height.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Locks in each workstation keyed to one key.

• One (1) mobile box/ file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

• Mobile Pedestal Cushion: Assume Grade C or Grade

III fabric allowance on cushion fabric.

• Black casters

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets

(described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

TACKABLE FABRIC-WRAPPED

MODESTY/PRIVACY PANEL

WOODGRAIN

LAMINATE

MOBILE BOX/FILE

PEDESTAL –

LAMINATE (SLATE

GREY)

WOODGRAIN

LAMINATE

PANEL

BA C D E F

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs.

Finishes

Line-item Pricing

MONITOR

6'-0"

6' -0

2' -6

2'-6"

3'-3"

5' -9

MONITOR

ACOUSTICAL FABRIC-WRAPPED

MODEST/PRIVACY PANEL

WOODGRAIN

LAMINATE

FROSTY WHITE

LAMINATE

WOODGRAIN

LAMINATE

MOBILE BOX/FILE

PEDESTAL -

LAMINATE (SLATE

GREY)

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-3

TYPICAL STAFF WORKSTATION – 6’ x 7’

A Worksurface Tops: HPL/TFL Frosty white laminate

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Cubbies, Base, Wall Panel: HPL/TFL Plastic Laminate Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Storage Components: HPL/TFL slate gray plastic laminate or similar

Fixed Worksurface

• 30”x53” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) +/- 48” H storage tower, plastic laminate finish. Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• One (1) box/ file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

• One (1) 30” D fixed rectangular worksurface at desk height, continuous across file cabinet pedestal.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Overhead open storage solution – Plastic Laminate

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

• Shared overhead storage cubbies. *Manufacturer to confirm weight capacity.

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

SHARED

OVERHEAD STOR.

CUBBIES

WOODGRAIN

LAMINATE

BOX/FILE

PEDESTAL – LAMINATE

(SLATE GREY)

PULL OUT STORAGE TOWER

– LAMINATE (SLATE GREY)

BA C D E

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

One (1) fixed box/box file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

10”H frosted acrylic stacker panels with eased edges.

Finishes

Line-item Pricing

FROSTY WHITE

LAMINATE

MONITOR

6' -0

8'-0"

4' -5

2'-6"

5'-3"

2'-6"

7'-0"

MONITOR

WOODGRAIN

LAMINATE

FROSTY WHITE

LAMINATE

BOX/FILE

PEDESTAL - LAMINATE

(SLATE GREY)

PULL OUT STORAGE TOWER

- LAMINATE (SLATE GREY)

SHARED OVERHEAD

STOR. CUBBIES

TACKABLE FABRIC- WRAPPED

MODESTY/ PRIVACY PANEL

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-4

TYPICAL STAFF WORKSTATION – 6’ x 8’

A Worksurface Tops: HPL/TFL Frosty white laminate

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Cubbies, Base, Wall Panel: HPL/TFL Plastic Laminate Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Storage Components: HPL/TFL slate gray plastic laminate or similar

Fixed Worksurface

• 30”x53” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) +/- 48” H storage tower, plastic laminate finish. Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• One (1) box/ file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

• One (1) 30” D fixed rectangular worksurface at desk height, continuous across file cabinet pedestal.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Overhead open storage solution – Plastic Laminate

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets (described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

• Shared overhead storage cubbies. *Manufacturer to confirm weight capacity.

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

SHARED

OVERHEAD STOR.

CUBBIES

WOODGRAIN

LAMINATE

BOX/FILE

PEDESTAL – LAMINATE

(SLATE GREY)

PULL OUT STORAGE TOWER

– LAMINATE (SLATE GREY)

BA C D E

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

One (1) fixed box/box file pedestal, with lock, per user with white plastic laminate drawers with full pull out.

Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

10”H frosted acrylic stacker panels with eased edges.

Finishes

Line-item Pricing

FROSTY WHITE

LAMINATE

MONITOR

6' -0

8'-0"

4' -5

2'-6"

5'-3"

2'-6"

MONITOR

WOODGRAIN

LAMINATE

FROSTY WHITE

LAMINATE

BOX/FILE

PEDESTAL - LAMINATE

(SLATE GREY)

TACKABLE FABRIC- WRAPPED

MODESTY/ PRIVACY PANEL

PULL OUT STORAGE

TOWER - LAMINATE

(SLATE GREY)

SHARED OVERHEAD

STOR. CUBBIES

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-5

TYPICAL STAFF WORKSTATION – 6’ x 9’

A Worksurface Tops: HPL/TFL Plastic Laminate: Frosty White

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Cubbies, Base, Wall Panel: HPL/TFL Plastic Laminate: Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Pedestal to be HPL/TFL slate gray plastic laminate or similar

F Mobile Pedestal Cushion: Momentum Deka Rain or similar.

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

10”H frosted acrylic stacker panels with eased edges.

• Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

Fixed Worksurface

• 30”x53” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) +/- 48” H pull out storage tower, plastic laminate finish.

Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• One (1) mobile box/ file pedestal + lateral file, with lock, per user with white plastic laminate drawers with full pull out.

• Mobile Pedestal Cushion: Assume Grade C or Grade III fabric allowance on cushion fabric.

• Black casters

• One (1) 30” D fixed rectangular worksurface at desk height, continuous across box/box/file pedestal + lateral file.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Overhead open storage solution – Plastic Laminate

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1) Type C USB ports and (2) electrical sockets (described above)

• Confirm power/data requirements with client

• Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

• Shared overhead storage cubbies.

*Manufacturer to confirm weight capacity.

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs

SHARED OVERHEAD

STOR.CUBBIES -

LAMINATE (SLATE

GREY)

MOBILE BOX/FILE

PEDESTAL – LAMINATE

(SLATE GREY)

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

PULL OUT STORAGE TOWER

– LAMINATE (SLATE GREY)

BA C D E F

Finishes

Line-item Pricing

FIXED LATERAL FILE–

LAMINATE (SLATE GREY)

MONITOR

9'-0"

6' -0

2'-6" 4' -5

6'-3"

2'-6"

MONITOR

FROSTY WHITE

LAMINATE

TACKABLE FABRIC- WRAPPED

MODESTY/ PRIVACY PANEL

PULL OUT STORAGE

TOWER - LAMINATE

(SLATE GREY)

MOBILE BOX/FILE

PEDESTAL - LAMINATE

(SLATE GREY)

SHARED OVERHEAD

STOR. CUBBIES

FIXED LATERAL FILE -

LAMINATE (SLATE GREY)

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-6

TYPICAL STAFF WORKSTATION – 7’-9” x 8’

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

10”H frosted acrylic stacker panels with eased edges.

• Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

Fixed Worksurface

• 30”x72” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) +/- 48” H pull out storage tower, plastic laminate finish.

Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• One (1) mobile box/ file pedestal + lateral file, with lock, per user with white plastic laminate drawers with full pull out.

• Mobile Pedestal Cushion: Assume Grade C or Grade III fabric allowance on cushion fabric.

• Black casters

• One (1) 30” D fixed rectangular worksurface at desk height, continuous across mobile box/file pedestal + lateral file.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Overhead open storage solution – Plastic Laminate

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1) Type C USB ports and (2) electrical sockets (described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

• Shared overhead storage cubbies. *Manufacturer to confirm weight capacity.

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs.

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

A Worksurface Tops: HPL/TFL Plastic Laminate: Frosty White

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Cubbies, Base, Wall Panel: HPL/TFL Plastic Laminate: Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Pedestal to be slate gray HPL/TFL plastic laminate or similar

F Mobile Pedestal Cushion: Momentum Deka Rain or similar.

BA C D E F

Finishes

Line-item Pricing

SHARED OVERHEAD

STOR.CUBBIES -

LAMINATE (SLATE

GREY)

MOBILE BOX/FILE

PEDESTAL – LAMINATE

(SLATE GREY)

PULL OUT STORAGE TOWER

– LAMINATE (SLATE GREY)

FIXED LATERAL FILE–

LAMINATE (SLATE GREY)

MONITOR

7' -9

8'-0"

2'-6" 6' -0

2'-6"

MONITOR

FROSTY WHITE

LAMINATE

TACKABLE FABRIC- WRAPPED

MODESTY/ PRIVACY PANEL

PULL OUT STORAGE

TOWER - LAMINATE

(SLATE GREY)

MOBILE BOX/FILE

PEDESTAL - LAMINATE

(SLATE GREY)

SHARED OVERHEAD

STOR. CUBBIES

FIXED LATERAL FILE -

LAMINATE (SLATE GREY)

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-7

TYPICAL STAFF WORKSTATION – 8’ x 9’

A Worksurface Tops: HPL/TFL Plastic Laminate: Frosty White

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

B Shared Cubbies, Base, Wall Panel: HPL/TFL Laminate Jubilee Oak or similar

C Fabric Wall Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Storage Components: HPL/TFL Plastic Laminate: Slate Gray or similar

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

• 10”H frosted acrylic stacker panels with eased edges.

• Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

Fixed Worksurface

• 30”x53” fixed rectangular work surface.

• Frosty White Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage + Return:

• One (1) +/- 48” H pull out storage tower, plastic laminate finish.

Provide info on available interior options – at minimum provide pricing for coat hook/bar and (1) shelf.

• One (1) box/ box drawer + lateral file + open shelf, with lock, per user with white plastic laminate drawers with full pull out.

• One (1) 30” D fixed rectangular worksurface at desk height, continuous across box/box/file pedestal + lateral file + open shelf.

• One (1) Woodgrain Plastic Laminate vertical end panel at open end of storage/return.

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide leg access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface power & 2 USB ports module for convenience (non-dedicated circuit) power access.

• Assume the following power/data requirements for each

Workstation with an 8 Circuit, 2General/2Isolated configuration:

• (6) electrical sockets, (2) network jacks, (1) convenience power module with (1) Type A and (1)

Type C USB ports and (2) electrical sockets

(described above)

• Confirm power/data requirements with client

Privacy Stacker Panels 48”H (at fence/spine if applicable – these panels are fixed):

• Assume Grade C or Grade III fabric allowance on tackable panels.

• Must have a minimum abrasion of Wyzenbeek 100,000 double rubs.

Gallery Panel Accessories (at return – these panels are fixed):

• Shared overhead storage cubbies. *Manufacturer to confirm weight capacity.

Woodgrain Plastic Laminate gallery panels at +/- 50”H at all corridor-adjacent ends of workstation runs

*RENDERING SHOWN WITH SIT TO STAND WORKTABLE. BOD TO BE PRICED AS A FIXED WORK SURFACE

OVERHEAD OPEN

STORAGE –

LAMINATE (SLATE

GREY)

WOODGRAIN

LAMINATE

BOX/BOX/FILE PEDESTAL +

LATERAL FILE – LAMINATE

(SLATE GREY)WOODGRAIN

LAMINATE

OPEN SHELF

BA C D E

Finishes

Line-item Pricing

MONITOR

9'-0"

8' -0

7'-8"

MONITOR

FROSTY WHITE

LAMINATE

TACKABLE FABRIC- WRAPPED

MODESTY/ PRIVACY PANEL

BOX/BOX/FILE PEDESTAL +

LATERAL FILE - LAMINATE

(SLATE GREY)

SHARED OVERHEAD

STOR. CUBBIES

WOODGRAIN

LAMINATE

WOODGRAIN

OPEN SHELF

Location: refer to floor plans

GEN. NOTES: NO VINYL ON THIS PROJECT. PROVIDE VINYL-ALTERNATIVE TEXTILES. MEDIUM GRAY METAL FINISH, TYP.

DEALER TO PROVIDE FINAL FURNITURE DRAWINGS AND QUANTITIES FOR APPROVAL PRIOR TO ORDERING.

LAYOUTS MUST COMPLY WITH TAS. WHERE MINIMUM CLEARANCES ARE NOT MET, DEALER TO PROVIDE SPECIAL.

POWER SPECS PROVIDED FOR PRICING – VERIFY WITH TFC A/V.

ALL TEXTILES TO BE GRADED IN.

SUBMIT ALL FINISHES TO TFC AND AOR FOR APPROVAL.

ALL WORKSTATIONS AND DESKS NEED TO COMPLY WITH CURRENT ELECTRICAL CODE. CONFIRM REQUIREMENTS WITH MEP ENGINEER.

WORKSTATIONS NEED CONTROLLED RECEPTACLES WITH THE FACTORY STAMP.

Item Description

Plan View + 3D

WS-8

TYPICAL STAFF WORKSTATION – 30”x10’

Provide line-item pricing for the following (price one):

• (1) Keyboard tray

• (1) Task Lamp

Sit-to-Stand Table in lieu of fixed worksurface located at work wall

• 30”x48” desk located at work wall

• Up/Down mechanism – simple paddle or buttons; may be pneumatic, electric or similar – no crank mechanism

• 10”H frosted acrylic stacker panels with eased edges.

• Dual Monitor Arm - include one (1) dual monitor arm per workstation.

Single mount preferred with slight screen adjustment (fully articulating arms not required).

B Worksurface Tops: HPL/TFL Woodgrain laminate Jubilee Oak or similar

Worksurface Edge Band: Matching ABS/thermo-plastic or similar edge

Storage Components, Modesty Panel

C Fabric Privacy Panels: Tackable fabric - warm gray neutral

D Exposed Metal Componentry and Pull Finish: Warm grey

E Pedestal to be slate gray HPL/TFL plastic laminate or similar

F Mobile Pedestal Cushion: Momentum Deka Rain or similar.

B C D F

Fixed Worksurface

• 30”x96” fixed rectangular work surface.

• Woodgrain Plastic Laminate worksurface with matching

ABS/thermo-plastic edge or similar.

Personal Storage:

• One (1) mobile box/ box drawer, with lock, per user with white plastic laminate drawers with full pull out.

• Mobile Pedestal Cushion: Assume Grade C or Grade

III fabric allowance on cushion fabric.

• Black casters

• Locks in each workstation keyed to one key.

• Parallel Bar Pulls – Warm grey or Similar

Worksurface Power:

• Provide along spine: power access/vertical cable carrier and cable management trough under worksurface; provide grommets as needed. No cords on floor will be acceptable.

• Docking station mounted underneath work surface or integrated in monitor arms if possible/applicable.

• Provide sleek (or pop up) work surface…