Engineering Data Requirements (Attachment A) 1560010479058FJ.docx

REV:

ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

XXXXXXXXXXXXXXXX

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

1234-12-123-1234FG

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC, WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

LOWER PANEL ASSY-INBD WING A-10

2. PART NUMBER:

160D611514-5

3. NATIONAL STOCK NUMBER:

1560-01-047-9058 FJ

THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

4. CONTRACTOR IS RESPONSIBLE TO COMPLETELY RESEARCH THESE MANUALS, SPECIFICATIONS, AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY FOR MANUFACTURE OF COMPONENT PARTS AND ASSEMBLIES. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED TO THE PROPER A-10 ENGINEERING ORGANIZATION FOR COORDINATION AND APPROVAL.

5. WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT'S CANCELLATION NOTICE. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). THE CONTRACTOR WILL COORDINATE WITH THE PROPER A-10 ENGINEERING ORGANIZATION FOR AUTHORIZATION AND APPROVAL OF THESE SUBSTITUTIONS PRIOR TO THE MANUFACTURING OF THIS COMPONENT. WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND RECOMMEND A SUBSTITUTE DOCUMENT FROM THE PROPER A-10 ENGINEERING ORGANIZATION BY CONTACTING THE GOVERNMENT CONTRACTING OFFICIAL.

6. USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS)

7. "IUID" (ITEM UNIQUE IDENTIFIER) IS REQUIRED IAW MIL-STD-130. SPECIFIC INSTRUCTIONS FOR MARKING METHODS, LOCATION, CONTENT AND FORMAT SHALL BE SPECIFIED BY THE CONTRACTOR AND SUBMITTED TO THE GOVERNMENT FOR APPROVAL PRIOR TO CONTRACT DELIVERY. THE CONTRACTOR MUST DEMONSTRATE THE MARKING DOES NOT ADVERSELY AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND ATTACHED THROUGHOUT THE USEABLE LIFE OF THE ITEM. IUID IS REQUIRED FOR ITEMS WHERE THE INDIVIDUAL COST PER UNIT IS GREATER THAN $5,000 OR IF THE ITEM HAS BEEN IDENTIFED AS FATIGUE CRITICAL REGARDLESS OF THE ITEMS PER UNIT COST.

8. PARTS LIST NOTE 17 FOR OVERSIZE TRIM IS REQUIRED

9. DISREGARD PARTS LIST NOTE 18. OMIT MATING/MOUNTING HOLES IN PART. DO NOT DRILL PILOT HOLES. THE PART WILL BE MATCHED/BACK DRILLED UPON INSTALLATION.

10. WARNING - THE DOCUMENTS LISTED ON THIS ENGINEERING DATA LIST (EDL) CONTAIN TECHNICAL DATA WHOSE EXPORT IS RESTRICTIVE BY THE ARMS EXPORT CONTROL ACT (TITLE 22, USC, SECTION 2751, ET SEQ.), OR THE EXPORT ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50 U.S.C, APPEND 2401 ET SEQ. VIOLATORS OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES.

PREPARED BY:

RICHARD TILTON

OFFICE SYMBOL:

GBMAF

DATE:

20080411

PREPARED BY:

Ezekiel Smith

OFFICE SYMBOL:

416 SCMS/GUEAB

DATE:

20210528

HILL AFB FORM 462 Page 1 of 1