Enclosure 1 Furniture Fixtures Equipment (FFE) Specifications.pdf

V88 ROC/Norfolk Naval Station/Norfolk, VA

Furniture, Fixtures & Equipment (FF&E) Specifications

Enclosure 1

1. D03, COMMAND CENTER DESK 24" x 60" w/ MOBILE PEDESTAL and DUAL

MONITOR ARM (Basis of design: Evans Millwork)

a. (12) Edge MT6 Starter Straight Console 60"L x 24"D with Slatrail & Cable Management, NIPR/SIPR Compliant Configuration

b. (24) Edge MT6 Add On Straight Console 60"L x 24"D with Slatrail & Cable Management, NIPR/SIPR Compliant Configuration

c. (12) Edge End Panel LH with Two Grommet Cutouts Custom Depth

d. (12) Edge End Panel RT with Two Grommet Cutouts Custom Depth

e. Control room desks shall be of design, construction and workmanship to withstand hard, daily usage over an extended life with minimum maintenance and repair. Work surfaces shall accommodate 2-24” wide monitors by using a single monitor arm.

f. Work surface grommets with a minimum area size of 4 square inches shall provide cable management access from desktop level to the wire cable basket below. Wire basket to be 4”w and run the full length of the work surface underneath.

g. Each desk to include a 6 outlet power strip with 6’ cord.

h. All Uprights and legs shall be high pressure laminate. A full depth leg design and full height modesty panel design will be used to address privacy and aesthetic requirements. 1” x 1” Vertical wire manager to be provided on each leg to run data cables to the work surface.

i. Modesty panel shall be high pressure laminate and includes cable raceway cutouts.

j. Modesty panels and upright HPL legs will have 1 ½” integrated leveler feet for ease of installation.

k. Laminate top shall be a core of 1.2" thick particle board with high pressure laminate overlay in a variety of colors. Laminate face shall be .028" WilsonArt decorative laminate or equivalent material.

l. Work surface nosing to be soft urethane. Secondary edges are finished with a flat PVC edge to match or complement the laminate color.

m. Laminate top shall include a smoothly finished black phenolic backing sheet or equivalent to provide dimensional stability and maximum warp resistance.

n. The laminate top shall not be affected by ordinary household solvents, acids, alcohols, or salt solutions and shall be capable of being cleaned with ordinary household cleaning solutions.

o. Horizontal track to be mounted at back of the work surface for monitor arm mounting

p. Finishes:

i. Laminate Top: Wilsonart Astro Standz

ii. PVC Edge: Grey (Storm)

iii. Laminate Base: Wilsonart Grey

iv. Metal Finish: Tiger Silver

A. Mobile Pedestal File Cabinets (for use with D03)

i. Quantity: 36

ii. Pedestals shall be mobile Box/File.

iii. Pedestals shall be tested in accordance with the requirements of

ANSI/BIFMA X5.5-1998 Section 14.

iv. All file drawers shall have full extension ball-bearing suspensions or slides.

v. All drawers shall operate smoothly but shall not open accidentally.

vi. Drawer front shall include a full width pull handle.

vii. Pedestal body shall of metal construction with seamless shell.

viii. Mobile pedestal shall include two (2) locking and two (2) non-locking casters that can be easily installed without tools.

ix. Drawers shall be of metal construction with a smooth finish. Mobile pedestals must be furnished with internal counterbalance weights to prevent instability and tipping.

x. Box drawer requirements include one (1) pencil or convenience tray and minimum of two (2) dividers.

xi. All file drawers shall come with hardware to accommodate legal or letter size hanging file folders.

B. Dual Monitor Arm (for use with D03) to include Slatrail Arm Mount

Kit

i. Quantity: 36

ii. Include a single desk clamp or track mount. Arms to provide @13” of height adjustment, 21” of depth adjustment, rotates 360 degrees and +/- 15 degrees of tilt.

iii. Accommodates (2) 24”w monitors

iv. Monitors to be able to move independently,

v. Include integrated cable management

vi. Slatrail Arm Mount Assembly Hardware must be included

2. CPU HOLDER (Basis of design: Workrite Ergonomics)

a. Quantity: 36

b. Swivels 360 degrees

c. Supports up to 50 pounds of CPU Weight

d. Easily adjusted to fit CPU widths from 3.75" – 8.25" and

Heights from 12"-20.50" using the included 5mm Hex wrench

e. Retractable and mounts underneath most work surfaces with an easy-to-install track

3. Console-Power-17-8-15

a. Quantity: 12

b. Power: 15A/120V

c. 17” long

d. (8) 5-15R transformer style outlets

e. 5-15P (straight blade) w/ 15’ cordset

f. LED power-on indicator

g. Vertical and horizontal mounting

4. C01, TASK CHAIR (Basis of Design: Allsteel Lyric)

a. Quantity: 55

b. Dimensions: 26”W x 26”D x 38 1/8” – 43 1/8”H

c. Features: high back, enhanced synchro-tilt control with 3 locking back positions, pneumatic seat-height adjustment, 4d fully adjustable arms, 3" seat depth adjustment, passive seat edge angle, and adjustable lumbar

d. Upholstered seat fabric:

a. Contourett UR10 Black

b. Mesh back: AM01 Carbon

c. Frame: Black

e. Casters shall be hard, dual wheels that roll smoothly on carpets. They are 2-1/2" for increased mobility. Soft, dark grey treaded, dual wheel roll-control casters are available for use on hard floors or mats. Soft casters are available as an option.

f. ANSI/BIFMA rated, 300 lbs. weight rated.

5. C02, GUEST CHAIR (Basis of Design: Gunlocke/Molti)

a. Quantity: 48

b. Overall dimensions: 24.5"w x 23"d x 33"h

c. Upholstered seat & back fabric: Lariat 440401 034 Macaw

d. Frame is constructed from round tubular steel.

a. Finish: Silver PR6

e. Seat shall be construction with filled foam over contoured plastic

f. Arms style: Moderne

a. Finish: Black

g. Standard plastic glides; casters shall be available.

h. ANSI/BIFMA X5.1 2017, 300 lb. weight rated

6. C03, EXECUTIVE CHAIR (Basis of design: Hon Endorse)

a. Quantity: 18

b. Overall dimensions: 26"w x 24"d x 37-1/4" to 42.5"h

c. Features: synchro-tilt mechanism, pneumatic seat-height adjustment, upright back lock, rectilinear independent height, width, pivot, and depth adjustable arms and soft arm caps: black plastic, 3" seat depth adjustment, passive seat edge angle, and adjustable lumbar.

d. Upholstered seat & back fabric: Lariat 440401 006 Black

e. Casters shall be hard, dual wheels that roll smoothly on carpets. They are

2-1/2" for increased mobility. Soft, dark grey treaded, dual

f. ANSI/BIFMA rated, 400 lbs. weight rated.

g. SCS Indoor Advantage Gold

7. C04, LOUNGE CHAIR (Basis of Design: Wieland Wedgewood Motion)

a. Quantity: 1

b. Overall dimensions: 25"w x 25.5"d x 39"h

c. Upholstered seat & back, mid-grade vinyl that shall be included in the proposal price from manufacturer's standard graded in upholstery offerings.

d. Waterfall seat design, generous lumbar support and gentle rocking movement.

Seat shall be constructed with filled foam.

e. Arms shall be constructed with bent plywood with Urethane arm cap.

f. Standard with removable seat and back cushions for ease of cleaning or replacement.

g. Wood frame construction. Select from manufacturer’s full range of wood finishes.

h. Standard plastic glides; casters shall be available.

i. ANSI/BIFMA X5.1 2017, 300 lb. weight rated

8. C05, OTTOMAN (Basis of Design: Wieland Rally Round Ottoman)

b. Overall dimensions: 22"W x 22"D x 18"H

c. Upholstered top, mid-grade vinyl that shall be included in the proposal price from manufacturer's standard graded in upholstery offerings.

d. Wood legs. Select from manufacturer’s full range of wood finishes.

e. Wood frame construction.

9. C06, BREAK ROOM CHAIR (Basis of Design: Krug Manolo)

a. Quantity: 3

b. Dimensions: 19”W x 22.5”D x 36”H with 31” seat height

c. Fully upholstered backless bar height stool, mid-grade vinyl upholstery that shall be include in the proposal price from manufacturer's standard graded in upholstery offerings.

d. Polished chrome base with non-marring polycarbonate glides.

e. 300lbs weight limit

10. D01, U-SHAPED DESK W/ WARDROBE (Basis of Design: Krug Adesso)

b. All components shall be veneer and from one manufacturer/product line.

a. Product shall also be non-handed.

c. Wood veneer work surfaces are 1-3/16” thick.

a. Veneer is plain sliced/slip matched.

b. Matching 3mm wood rim finish.

c. Semi-open pore matte finish.

d. Indoor Advantage gold.

e. Provide undersurface wire management every 36”.

d. Grain direction runs left-to-right unless otherwise noted

e. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. Provide undersurface wire management every 36”.

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Modesty panels shall be 1/3 height where desks are against walls and full height when not against walls.

j. Provide silver metallic, linear pull for all pedestals.

k. All storage keyed alike. Silver, metal lock cores

l. 30”D x 72”D, desk shall include (2) desktop grommets, full height modesty panel, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

m. 24”d x 42”w Electrical, adjustable height desk bridge with center grommet.

Height range from 21”h to 47”h with a 10’ long power cord.

n. 24”d x 72”w credenza work surface shall feature (2) desktop grommets and 1/2 height modesty with grommet. Provide (1) pedestal – undersurface file/file 23"d x 18”w.

o. 30”w x 24”d x 80”h veneer, double door combo wardrobe/storage. Shall have wood chassis and frosted glass doors. 2 fixed and 3 adjustable shelves. Coat rod standard. No locks.

p. ANSI/BIFMA X5.5-2014 desk/table products.

q. Finishes:

i. Wood Veneer: Espresso Rift Oak

ii. Glass Doors: White Frosted Glass

iii. Pull: Silver Metallic

11. D02 L-SHAPE DESK WITH HUTCH (Basis of Design: Krug Artemis)

a. Quantity: 2

b. All components shall be High Pressure Laminate with Polymer edge to match and are from one manufacturer/product line.

a. Product shall also be non-handed.

c. 1 ¼” thick work surfaces with polymer edge.

d. Wood grain laminate to run left-to-right unless otherwise noted.

e. Provide undersurface wire management every 36”.

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Provide desk supported hutch with lockable doors, tack board and tasklight. Clearance from the worksurface to the bottom of the hutch to be 23 ½”.

j. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

k. Provide silver metallic, linear pull for all pedestals.

l. All storage keyed alike. Silver, metal lock cores

m. 30”D x 72”D, desk shall include (2) desktop grommets, 1/2 height modesty panel, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

n. 78”w x 39.5”h Hutch to include task lighting, frosted glass doors and tack board priced.

o. 24”D x 48”W return worksurface shall feature (1) desktop grommet and 1/2 height modesty. Provide (1) pedestal – undersurface file/file 23"d x 18”w.

p. ANSI/BIFMA X5.5-2014 desk/table products

q. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

iii. Tack board: Grade 4

iv. Pull: Silver Metallic

12. D04 COMMAND CENTER DESK 36" x 300” w/ (5) MOBILE PEDESTALS and (5) DUAL MONITOR ARMS (Basis of design: Evans Millwork)

b. Control room desks shall be of design, construction and workmanship to withstand hard, daily usage over an extended life with minimum maintenance and repair. Work surfaces shall accommodate 2-24” wide monitors by using a single monitor arm.

c. Work surface grommets with a minimum area size of 4 square inches shall provide cable management access from desktop level to the wire cable basket below. Wire basket to be 4”w and run the full length of the work surface underneath.

d. Each desk to include a 6 outlet power strip with 6’ cord.

e. All Uprights and legs shall be high pressure laminate. A full depth leg design and full height modesty panel design will be used to address privacy and aesthetic requirements. 1” x 1” Vertical wire manager to be provided on each leg to run data cables to the work surface.

f. Modesty panel shall be high pressure laminate and includes cable raceway cutouts.

g. Modesty panels and upright HPL legs will have 1 ½” integrated leveler feet for ease of installation.

h. Laminate top shall be a core of 1.2" thick particle board with high pressure laminate overlay in a variety of colors. Laminate face shall be .028" WilsonArt decorative laminate or equivalent material.

i. Work surface nosing to be soft urethane. Secondary edges are finished with a flat PVC edge to match or complement the laminate color.

j. Laminate top shall include a smoothly finished black phenolic backing sheet or equivalent to provide dimensional stability and maximum warp resistance.

k. The laminate top shall not be affected by ordinary household solvents, acids, alcohols, or salt solutions and shall be capable of being cleaned with ordinary household cleaning solutions.

l. Horizontal track to be mounted at back of the work surface for monitor arm mounting

m. Finishes:

i. Laminate Top: Wilsonart Astro Standz

ii. PVC Edge: Grey (Storm)

iii. Laminate Base: Wilsonart Grey

iv. Metal Finish: Tiger Silver

A. Mobile Pedestal File Cabinets (for use with D04)

b. Pedestals shall be mobile Box/File.

c. Pedestals shall be tested in accordance with the requirements of ANSI/BIFMA

X5.5-1998 Section 14.

d. All file drawers shall have full extension ball-bearing suspensions or slides.

e. All drawers shall operate smoothly but shall not open accidentally.

f. Drawer front shall include a full width pull handle.

g. Pedestal body shall of metal construction with seamless shell.

h. Mobile pedestal shall include two (2) locking and two (2) non-locking casters that can be easily installed without tools.

i. Drawers shall be of metal construction with a smooth finish. Mobile pedestals must be furnished with internal counterbalance weights to prevent instability and tipping.

j. Box drawer requirements include one (1) pencil or convenience tray and minimum of two (2) dividers.

k. All file drawers shall come with hardware to accommodate legal or letter size hanging file folders.

B. Dual Monitor Arm (for use with D04)

b. Include a single desk clamp or track mount. Arms to provide @13” of height adjustment, 21” of depth adjustment, rotates 360 degrees and +/- 15 degrees of tilt.

c. Accommodates (2) 24”w monitors

d. Monitors to be able to move independently,

e. Include integrated cable management

13. D05 SINGLE PEDESTAL DESK WITH HUTCH (Basis of Design: Krug Artemis)

a. Quantity: 10

b. All components shall be High Pressure Laminate with Polymer edge to match and are from one manufacturer/product line. Product shall also be non-handed.

c. 1 ¼” thick work surfaces with polymer edge.

d. Wood grain laminate to run left-to-right unless otherwise noted.

e. Provide undersurface wire management every 36”.

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Provide desk supported hutch with lockable doors, tack board and tasklight. Clearance from the work surface to the bottom of the hutch to be 23 ½”.

j. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

k. Provide silver metallic, linear pull for all pedestals.

l. All storage keyed alike. Silver, metal lock cores

m. 30”D x 72”D, desk shall include (2) desktop grommets, ½ height modesty pane, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

n. 72”W Hutch to include task lighting, frosted glass doors and tack board.

o. ANSI/BIFMA X5.5-2014 desk/table products

p. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

14. D06 SINGLE PEDESTAL DESK (Basis of Design: Krug Artemis)

b. All components shall be High Pressure Laminate with Polymer edge and from one manufacturer/product line. Product shall also be non-handed.

c. 1 ¼” thick worksurfaces with polymer edge.

d. Wood grain laminate to run left-to-right unless otherwise noted.

e. Provide undersurface wire management every 36”.

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

j. Provide silver metallic, linear pull for all pedestals.

k. All storage keyed alike. Silver, metal lock cores

l. 24”D x 48”D, desk shall include desktop grommet, ½ height modesty panel, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

m. ANSI/BIFMA X5.5-2014 desk/table products

n. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

15. D07 L-SHAPE DESK (Basis of Design: Krug Artemis)

b. All components shall be High Pressure Laminate with Polymer edge and from one manufacturer/product line. Product shall also be non-handed.

c. 1 ¼” thick worksurfaces with polymer edge.

d. Wood grain laminate to run left-to-right unless otherwise noted.

e. Provide undersurface wire management every 36”.

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

j. Provide silver metallic, linear pull for all pedestals.

k. All storage keyed alike. Silver, metal lock cores

l. 30”D x 66”D, desk shall include (2) desktop grommets, ½ height modesty panel, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

m. 24”d x 48”w worksurface shall feature (1) desktop grommet and 1/2 height modesty with grommet. Provide (1) pedestal – undersurface file/file 23"d x 18”w.

n. ANSI/BIFMA X5.5-2014 desk/table products

o. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

16. D08 SINGLE PEDESTAL DESK (Basis of Design: Krug Artemis)

b. All components shall be High Pressure Laminate with Polymer edge to match and are from one manufacturer/product line. Product shall also be non-handed.

c. 1 ¼” thick worksurfaces with polymer edge.

d. Wood grain laminate to run left-to-right unless otherwise noted.

e. Provide undersurface wire management every 36”.

f. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

g. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

h. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

i. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

j. Provide silver metallic, linear pull for all pedestals.

k. All storage keyed alike. Silver, metal lock cores

l. 30”D x 60”D, desk shall include (2) desktop grommets, ½ height modesty panel, and (1) pedestal - undersurface box/box/file 29"d x 18w that includes a removable pencil tray.

m. ANSI/BIFMA X5.5-2014 desk/table products

n. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

17. D11, 24”x 72” L-SHAPED DESK (Basis of Design: Krug Artemis)

b. All components shall be High Pressure Laminate with Polymer edge and from one manufacturer/product line. Product shall also be non-handed.

c. Provide undersurface wire management every 36”.

d. Provide undersurface mounted 6 outlet power strip with 10’ long cord.

e. All joints are securely fastened by screws, L-brackets, dowels, and concealed fasteners to ensure maximum strength

f. Pedestal drawers shall feature 5-sided construction allowing for easy removal/replacement of drawer fronts. Shall meet extendible elements cycle test: Evaluates the operation of casegood extendible member to ensure that suspension systems can support typical loads while being opened and closed. Extendible member load –.017 lb./cubic inch of filing volume, 30,000 cycles in center of pull area 10,000 cycles on each side of center pull

g. Modesty panels shall be 1/2 height where desks are against walls and full height when not against walls.

h. Provide silver metallic, linear pull for all pedestals.

i. All storage keyed alike. Silver, metal lock cores

j. 24”D x 72”D, desk shall include (1) pedestal - undersurface box/box/file

29"d x 18w that includes a removable pencil tray. ½ height modesty panel with metal grommet.

k. 24”d x 42”w worksurface shall feature a 1/2 height modesty with grommet.

Provide (1) pedestal – undersurface file/file 23"d x 18”w.

l. ANSI/BIFMA X5.5-2014 desk/table products

m. Finishes:

i. Laminate: Dark Walnut

ii. Glass Doors – White Frosted Glass

18. M01, 5 ZONE TIME CLOCK (Basis of design: Digital Display)

a. Quantity: 8

b. Wall mounted bar style LED digital display for 5 time zones, horizontal, 24-hour format.

c. Automatic daylight savings time correction, 1 second a year accuracy.

d. Selectable 31 current world time zones.

e. 1.8”h time labels, 0.75” dot matrix LEDs for zone labels, visible from 75 ft.

f. Power: Standard receptacle with external transformer with power surge protection.

g. 10-year lithium battery backup to ensure accuracy through power outages.

h. PC operation needed for display and time setup; clock runs without PC support.

19. M02, DESK TRASH CAN (Basis of design: Alle)

a. Quantity: 19

b. Dimensions: 10.2"W x 14.4"D x 15"H

c. Material Type: resin

d. Finish: Black

e. Trash can consists of an all-plastic construction featuring rolled rim

f. 28 quart capacity.

20. M03, CLASSIFIED SHREDDER (Basis of design: Capital Shedder/ M-12CT)

b. Overall dimensions: Dimensions: 34-1/2"h x 29"w x 20"d

c. Cut type: DOD Level 6 / P-7 Cross Cut

d. Entry Width: 12"

e. Shred Size: 1mm x 4.7mm particles

f. Sheet Capacity*: Up to 12 sheets

g. Speed: 23 FPM

h. Motor Peak: 2.7 Hp

i. Waste Capacity: 38 Gal

j. Features: Auto On/Off, Bag Full Indicator

21. M04, REFRIGERATOR (Basis of design: GE appliances/ GDE25ESKSS)

b. Overall dimensions: 32-3/4 “W x 37-1/2” D x 69-7/8”H

c. Total Capacity: 24.9 Cu. Ft.

d. Refrigerator Capacity: 17.6 Cu. Ft. Freezer Capacity: 7.3 Cu. Ft.

e. Bottom freezer

f. Stainless steel finish

g. Ice maker included

h. Reversible doors

i. Features: Features 2 full-width adjustable glass shelves, 2 half-width humidity controlled crispers, 2 full-width door bins and 2 half-width door bins for diverse storage options.

j. ENERGY STAR rated.

22. M05, MICROWAVE (Basis of design: GE)

b. Overall dimensions: 23-7/8”W x 19-15/16”D x 14”H

a. cubic foot capacity

c. Built-In/Countertop Microwave Oven with Inverter Technology

d. 16.5” turntable

e. Stainless Steel finish

f. 1250 watt high power

g. 10 power levels, 19 preset auto cook menu items, and a keep warm feature. Unit complies with 2016 DOE Energy

h. Microwave controls: 19 preset auto cook menu items, Delay start and timer; more/less control; Child safety lock; Quick 30 sec and popcorn button with 3 cooking levels, clock: 12h

i. 1 year warranty on parts and labor.

23. M06, COFFEE MAKER, PLUMBED (Basis of design: Bunn/AXIOM®-15-3/38700.0002)

b. Dimensions: 16.8 ”H x 16.3”W x 22.1”D

c. 3 lower warmers

d. Stainless steel finish

e. NSF certified for use in foodservice. UL listed

f. Water access: plumbed

g. Adjusts automatically to varying water pressure

h. Automatic warmer shut-off

i. BrewLOGIC® technology

j. 200oz. (5.9L) tank

k. Energy-saver mode

l. Hot water faucet

m. SplashGard® funnel

n. (3) Servers shall be included unless otherwise noted. (2) regular/black handle & (1) decaf/orange handle

24. M07, TRASH CAN (Basis of design: Rubbermaid)

b. Dimensions: 11.31"W x 15.3"D x 20”H

c. Black plastic

d. Rectilinear shape

e. 10 gallon capacity

f. Commercial grade

g. Bag cinches secure liners around the rim.

25. M08, RECYCLE CAN (Basis of design: Rubbermaid)

b. Dimensions: 11.31"W x 15.3"D x 20”H

c. Blue Plastic, Recycle Icon

d. Rectilinear shape

e. 10 gallon capacity

f. Commercial grade

g. Bag cinches secure liners around the rim

26. M09, BUILT-IN UNDER COUNTER REFRIGERATOR (Basis of design: Summit Appliances)

b. Dimensions 21”W x 22.5”D x 32”H

c. 3.53 cu. Ft. Interior

d. Built-in Undercounter Refrigerator-Freezer

e. ADA Compliant

f. Reversible door

g. Energy Star Rated

h. (3) removable door racks for additional storage

i. (3) adjustable spill-proof shelves for optimal storage

j. Fruit and vegetable crisper

k. 3” thick door for improved insulation and efficiency

l. Stainless steel finish

27. M10, COMPACT MINI FRIDGE (Basis of design: Insignia)

b. Dimensions 17.5”W x 19.5”H x 19”D

c. 1.7 Cu.Ft.

d. Single Temperature Controlled Zone

e. (1) Full width wire shelf, (1) full door rack

f. Reversible Door

g. Black finish

28. M11, SHOWER CURTAIN (Basis of design: Rooms Made Perfect)

b. Dimensions 42”W x 74”H

c. Split Rings for Hook less Installation

d. Translucent top window

e. 100% polyester fabric, waffle weave texture, mold & mildew resistant

f. Includes snap in liner

g. Weighted Corner Magnets

29. M12, CELL PHONE LOCKER (Basis of design: National Mailboxes)

b. Dimensions 37”W x 9”D x 66.5”H

c. (35) 5”H x 6.5”W Lockers

d. (4) 5”H x 13”W Lockers

e. All lockers to have resettable combination locks

f. Freestanding

g. Powder coated aluminum finish. Available selection from manufacturer’s full range of colors.

30. M13, CELL PHONE LOCKER (Basis of design: National Mailboxes)

b. Dimensions 30.5”W x 9”D x 66.5”H

c. (27) 5”H x 6.5”W Lockers

d. All lockers to have resettable combination locks

e. Freestanding

f. Powder coated aluminum finish. Available selection from manufacturer’s full range of colors.

31. M14, 12 POCKET BADGE RACK (Basis of design: Global Industrial)

b. Dimensions: 4”W x 2/3”D x 14-1/4”H

c. Constructed of lightweight, durable plastic

d. Holds 24 standard sized ( 3 ½” x 2”) cards and badges

e. Mounting hardware to be included

32. M15, CPU HOLDER (Basis of design: Workrite Ergonomics)

a. Quantity: 51

b. Adjustable CPU holder that accommodates 9.75” to 18.5”h, 1.25” to 8.75”w, 8” to 19.25”d

c. 16”l track allows 10” of travel and 360 degree swivel for easy access to the rear of the CPU

d. Supports CPUs up to 75lbs.

e. Adjustable bottom bracket and tamper resistant screws for track mount.

33. M16, LAPTOP TRAY (Basis of design: Humanscale)

a. Quantity: 56

b. Slim design vented shelf, 12”w x 14”d x 3.5”h with cable access grommets at the back.

c. 16”l track

d. Made of steel for strength and durability

e. 15 year 24/7 warranty

34. S01, 2H 36”W DOUBLE DOOR STORAGE CABINET (Basis of design: Great Openings)

b. Dimensions: 36”W x 18”D x 27-1/4”H

c. Unit features (1) standard adjustable shelf, in 1.6” increments

d. Constructed with a minimum of 20 gauge steel

e. 1” leveling glides

f. Full Integral pull style

g. Silver lock core, random keyed

h. Provide QTY. (1) 36”w x 18”d x 1-3/16”h, HPL laminate top.

i. Finish:

i. Metal Finish: 0112 Putty

ii. Laminate Top: DMGH Slate Grey

35. S02, 2H 42”W DOUBLE DOOR STORAGE CABINET (Basis of design: Great Openings)

b. Dimensions: 42”w x 18”d x 27-1/4”h

c. Unit features (1) standard adjustable shelf, in 1.6” increments

d. Constructed with a minimum of 20 gauge steel

e. 1” leveling glides

f. Full Integral pull style

g. Silver lock core, random keyed

h. Provide QTY. (1) 42”w x 18”d x 1-3/16”h, HPL laminate top.

i. Finish:

a. Metal Finish: 0112 Putty

b. Laminate Top: DMGH Slate Grey

36. S03, 4 POST 36”W x 15”D x 75”H ADJUSTABLE SHELVING (Basis of design: Tennsco Q Line)

b. Steel industrial shelving unit, open sides and back

c. Overall size: 36”w x 15”d x 75”h

d. Five Shelves, 22 gauge, four openings

e. Shelf capacity: 1,000 pounds.

f. Shelf corners shall be fully lapped

g. Shelves adjust on 1” increments

h. Epoxy paint finish. 3 standard colors available

i. 13 gauge compression clips

37. S04, 4 POST 42”W x 15”D x 75”H ADJUSTABLE SHELVING (Basis of design: Tennsco Q Line)

b. Steel industrial shelving unit, open sides and back

c. Overall size: 42”w x 15”d x 75”h

d. Five Shelves, 22 gauge, four openings

e. Shelf capacity: 1,000 pounds.

f. Shelf corners shall be fully lapped

g. Shelves adjust on 1” increments

h. Epoxy paint finish. 3 standard colors available

i. 13 gauge compression clips

38. S05, 5H 42”W LATERAL FILE CABINET (Basis of design: Great Openings)

b. Dimensions: 42”w x 18”d x 27 ¼”h

c. Constructed with a minimum of 20 gauge steel

d. 1” leveling glides

e. Full integral pull style

f. Silver lock core, random keyed

g. Provide front to back hanging rails

h. Finish:

i. Metal Finish: 0112 Putty

39. T01, CONFERENCE TABLE 144"L x 60"D w/ (1) POWER/DATA PORT (Basis of design: Krug Nuvo)

b. Overall dimensions: 60”w x 144”l rectangular

c. Conference table shall have 1-3/16” thick laminate top with wood edge.

d. Provide QTY. (1) power/data table top module that includes

(2) power outlets, (2) HDMI ports, (2) VGA ports, (2) DVI ports, (2) black ports, (1) 72” long power cord and horizontal wire manager.

e. Matching wood veneer thick base kit with silver, metal accent foot. Horizontal support rails shall match finish/laminate of panel bases. Adjustable glides standard.

Bases have wire access for access to floor mounted electrical

f. Finish: Dark Walnut Laminate

40. T02, LAPTOP TABLE (Basis of design: National Universal)

b. Overall dimensions: 13 ¼”d x 22”w x 28.5h

c. Laptop table worksurface shall be constructed of 13 Ú16" HPL

(high pressure laminate). Select from manufacturer’s full line of colors.

d. Rims are a 3mm softened profile

e. Metal legs available in manufacturer’s full range of colors

41. T03, 7 PERSON BOAT SHAPE COLLABORATION TABLE w/ MONITOR LIFTS (Basis of Design: Nova Desk)

b. Dimensions: 60”d x 141-3/8”w x 30”h

c. Table to accommodate (3) users on each side, (1) user on an end and a 6”x36” cable compartment on the opposite end

d. High Pressure Laminate work surface and base. Select from manufacturer’s full range of colors.

e. Flat PVC Edgebanding

f. Provide grommets

g. Built in wire management and six plug power strip per user

h. Keyboard tray (7) to be included for each monitor station. Keyboard tray to include a wrist rest and should be able to lock in multiple positions and store neatly under worksurface

i. Monitor Lift

i. Provide (7) electronic motor driven monitor lifts to fit a 24” minimum monitor; (1) monitor lift per monitor

ii. Worksurface footprint a minimum of 8 ½”d x 28 ½”w

iii. Minimum knee space width 27”

iv. 110-240 Volts, 50-60Hz Universal Power Supply

v. Access doors will be auto/retractable

vi. Push Button (up/down) activation control

vii. Vertical Tilt Monitor adjustment while in raised position

42. T04, BREAK ROOM TABLE (Basis of Design: National Strassa)

b. Dimensions: 84”W x 24”D x 41 ½ ”H

c. 1 3/16” thick high pressure laminate top with a softened 3 mmm vinyl rim. Price in a wood grain laminate. Matching wood grain on chassis/end panels. Wood Grain to run left-to-right.

d. All joints securely fastened by screws l-brackets, dowels, and concealed fasteners to ensure maximum strength.

e. End panels to be 3” thick and include adjustable leveling glides

f. Table to be without modesty panel.

43. T05, MOBILE BOX/BOX/FILE PEDESTAL (Basis of Design: Evans)

a. Quantity: 7

b. Pedestals shall be available mobile.

c. Pedestals shall be tested in accordance with the requirements of

ANSI/BIFMA X5.5-1998 Section 14.

d. All file drawers shall have full extension ball-bearing suspensions or slides.

e. All drawers shall operate smoothly but shall not open accidentally.

f. Drawer front shall include a full width pull handle.

g. Pedestal body shall of metal construction with seamless shell.

h. Mobile pedestal shall include two (2) locking and two (2) non-locking casters that can be easily installed without tools.

i. Drawers shall be of metal construction with a smooth finish. Mobile pedestals must be furnished with internal counterbalance weights to prevent instability and tipping.

j. Box drawer requirements include one (1) pencil or convenience tray and minimum of two (2) dividers.

k. All file drawers shall come with hardware to accommodate legal or letter size hanging file folders.

l. Finishes to be selected from manufacturer’s full range of colors.