Encl 9 - Performance Work Statement (PWS).pdf

CUI

PERFORMANCE WORK STATEMENT (PWS)

FOR

Fire Extinguisher Maintenance Services

1.0 General:

1.1 Scope: The contractor shall provide all personnel, equipment, tools, materials, supervision, and quality control necessary, except as specified in Paragraph 3.0 as Government Furnished, to perform Fire Extinguisher Maintenance Services, as defined in this PWS.

1.1.1 Objectives (This section may be added, if needed)

1.2 Background: In accordance with (IAW) NFPA 10, Chapter 7, 2026 edition, Perform annual and recurring maintenance on fire extinguishers utilized at the 182d Airlift Wing.

1.3 Period of Performance (PoP): The Period of Performance shall be 1 Base Year of 12 months and ____4____ 12-month option years.

1.4 General Information:

1.4.1 Place and Performance of Services: The contractor shall provide services between the hours of 0730-1630 on a pre scheduled week day that are mutually agreed to prior to the service between the government and the contractor, except on recognized US holidays or when the Government facility/installation is closed due to local or national emergencies, administrative closings, or similar Government-directed facility/installation closings.

Performance shall be at Building 541. The contractor shall at all times maintain an adequate work force for the uninterrupted performance of all tasks defined within this PWS when the Government facility/installation is not closed for the above reasons. When hiring personnel, the contractor shall keep in mind that the stability and continuity of the work force are essential.

1.4.1.2 Unscheduled gate closures by the Security Police may occur at any time causing all personnel entering or exiting a closed installation to experience a delay. This cannot be predicted or prevented. Contractors are not compensated for unexpected closures or delays.

Vehicles operated by contractor personnel are subject to search pursuant to applicable regulations. Any moving violation of any applicable motor vehicle regulation may result in the termination of the contractor employee’s installation driving privileges.

1.4.1.3 The contractor’s employees shall become familiar with and obey the regulations of the installation; including fire, traffic, safety and security regulations while on the installation.

Contractor employees should only enter restricted areas when required to do so and only upon prior approval. All contractor employees shall carry proper identification with them at all times, and shall be subject to such checks as may be deemed necessary. The contractor shall ensure compliance with all regulations and orders of the installation, which may affect performance.

The Government reserves the right to direct the removal of an employee from Government property or revoke access to Government systems for misconduct, security reasons, or any overt evidence of communicable disease. Removal of contractor employees for reasons stated above does not relieve the Contractor from responsibility for total performance of this contract.

1.4.4 Quality Assurance (QA): The Government will evaluate the contractor’s performance under this contract in accordance with the Quality Assurance Surveillance Plan (QASP). This plan is primarily focused on what the Government will do to ensure that the contractor has performed in accordance with the performance standards. It defines how the performance standards will be applied, the frequency of surveillance, and acceptable quality level(s) or defect rate(s).

1.4.5 Access and General Protection/Security Policy and Procedures. The contractor shall comply with all applicable installation/facility access and local security policies and procedures, which may be obtained from the Contracting Officer’s Representative (COR). The contractor shall also provide all information required for background checks to meet installation access requirements to be accomplished by the local installation’s Security Forces, Director of Emergency Services or local Security Office. The contractor shall ensure compliance with all personal identity verification requirements as directed by DoD, Headquarters Air Force (HAF) and/or local policy. Should the Force Protection Condition (FPCON) change, the Government may require changes in contractor security matters or processes.

1.4.5.1. The contractor shall obtain base identification, and vehicle passes, if required, for all contractor personnel who make frequent visits to or perform work on the Air Force installations(s) cited in the contract. Contractor personnel are required to wear or prominently display installation identification badges or contractor-furnished, contractor identification badges while visiting or performing work on the installation.

1.4.5.2. The contractor shall submit a written request on company letterhead to the contracting officer listing the following: contract number, location of work site, start and stop dates, and

CUI

names of employees and subcontractor employees needing access to the base. The letter will also specify the individual(s) authorized to sign for a request for base identification credentials or vehicle passes. The contracting officer will endorse the request and forward it to the issuing base pass and registration office or Security Forces for processing. When reporting to the registration office, the authorized contractor individual(s) should provide a valid driver s license, current vehicle registration, valid vehicle insurance certificate, and [insert any additional requirements to comply with local security procedures] to obtain a vehicle pass.

1.4.5.3. During performance of the contract, the contractor shall be responsible for obtaining required identification for newly assigned personnel and for prompt return of credentials and vehicle passes for any employee who no longer requires access to the work site.

1.4.5.4. When work under this contract requires unescorted entry to controlled or restricted areas, the contractor shall comply with DODMAN5200.02_AFMAN 16-1405, Air Force Personnel Security Program, citing the appropriate paragraphs as applicable).

1.4.5.5. Upon completion or termination of the contract or expiration of the identification passes, the prime contractor shall ensure that all base identification passes issued to employees and subcontractor employees are returned to the issuing office.

1.4.5.6. Failure to comply with these requirements may result in withholding of final payment.

1.4.5.5 Communications Security/Information Technology (COMSEC/IT) Security. All communications with DoD organizations are subject to COMSEC review. All telephone communications networks are continually subject to intercept by unfriendly intelligence organizations. DoD has authorized the military departments to conduct COMSEC monitoring and recording of telephone calls originating from, or terminating at, DoD organizations.

Therefore, the contractor is advised that any time contractor personnel place or receive a call they are subject to COMSEC procedures. The contractor shall ensure wide and frequent dissemination of the above information to all employees dealing with DoD information. The contractor shall abide by all Government regulations concerning the authorized use of the Government's computer network, including the restriction against using the network to recruit Government personnel or advertise job openings.

1.4.6 Physical Security. The contractor shall safeguard all Government property provided for contractor use. At the close of each work period, Government facilities, equipment and materials shall be secured.

https://static.e-publishing.af.mil/production/1/saf_aa/publication/dodman5200.02_afman16-1405/dodm5200.02_afman16-1405.pdf

CUI

1.4.7 Special Qualifications: IAW NFPA 10, Chapter 7, 2026 edition, paragraph 7.1.2. All persons Performing maintenance and recharging of extinguishers shall be certified. Contractor shall provide an issued document or certificate prior to performing maintenance IAW paragraph

7.1.2.1.5. (NOTE: The Government does not provide training to contractors. Contractors must ensure that any personnel performing under a contract are fully trained, licensed, certified, and otherwise qualified to provide services.)

1.4.8 Post Award Conference/Periodic Progress Meetings: The contractor agrees to attend any post award conference convened by the KO in accordance with FAR 42.5. The KO, COR and other Government personnel, as appropriate, may meet periodically with the contractor to review the contactor’s performance. At these meetings, the KO will apprise the contractor of how the Government views the contractor’s performance and the contractor shall apprise the Government of problems, if any, being experienced. The contractor shall resolve outstanding issues raised by the Government. Contractor attendance at these meetings shall be at no additional cost to the Government.

1.4.9 Contract Manager (CM): The contactor shall designate a CM who shall ensure performance under this contract. The name of this person, and an alternate who shall act for the contractor when the CM is absent, shall be designated in writing to the KO. The CM or alternate shall have full authority to act for the contractor on all contract matters relating to daily operation of this contract. The CM shall work through the KO, to resolve issues, receive technical instructions, and ensure adequate performance of services. The CM shall ensure that contractor employees do not perform any services outside the scope of the contract without an official modification issued by the KO. The CM shall ensure contractor employees understand that services performed outside the scope of the contract are performed wholly at the expense of the contractor.

1.4.10 Identification of Contractor Employees: All contractor personnel attending meetings, answering Government telephones and working in other situations where their contractor status is not obvious to third parties are required to identify themselves as such to avoid creating an impression that they are Government employees. The contractor shall ensure that all documents or reports produced by contractor personnel are suitably marked as contractor products or that contractor participation is appropriately disclosed. The contractor’s status as a “contractor” shall be predominantly displayed in all correspondence types (to include signature blocks on e-mail) and dealings with Government or non-Government entities. Contractor personnel shall wear identification badges distinguishing themselves as such. The badges shall have the company name, employee name and the word “contractor” displayed.

CUI

1.4.11. Combating Trafficking in Persons: The United States Government has adopted a zero-tolerance policy regarding trafficking in persons. Contractors and contractor employees shall not engage in severe forms of trafficking in persons during the period of performance of the contract; procure commercial sex acts during the period of performance of the contract; or use forced labor in the performance of the contract. The Contractor shall notify its employees of the United States Government’s zero tolerance policy, the actions that will be taken against employees for violations of this policy. The contractor shall take appropriate action, up to and including termination, against employees or subcontractors that violate the US Government policy as described at FAR 22.17.

2.0 Definitions and Acronyms:

2.1 Definitions:

2.1.1 Contractor: A supplier or vendor awarded a contract to provide specific supplies or service to the Government. The term used in this contract refers to the prime.

2.1.2 Defective Service: A service output that does not meet the standard of performance associated with the PWS.

2.1.3 Deliverable: Anything that can be physically delivered and includes non-manufactured things such as meeting minutes or reports.

2.1.4 Key Personnel: Contractor personnel that are evaluated in a source selection process and that may be required to be used in the performance of a contract by the PWS. When key personnel are used as an evaluation factor in best value procurement, an offer can be rejected if it does not have a firm commitment from the persons that are listed in the proposal.

2.1.5 Physical Security: Actions that prevent the loss or damage of Government property.

2.1.6 Quality Assurance: The Government procedures to verify that services being performed by the Contractor are performed according to acceptable standards.

2.1.7 Quality Assurance Surveillance Plan (QASP): An organized written document specifying the surveillance methodology to be used for surveillance of contractor performance.

2.1.8 Quality Control: All necessary measures taken by the Contractor to ensure that the quality of an end product or service shall meet contract requirements.

2.1.9 Subcontractor: One that enters into a contract with a prime contractor. The Government does not have privity of contract with the subcontractor.

2.2 Acronyms:

AEI Army Enterprise Infostructure AR Army Regulation AT/OPSEC Antiterrorism/Operational Security BI Background Investigation CM Contract Manager COR Contracting Officer Representative DA Department of the Army DAFI Department of the Air Force Instruction DD254 Department of Defense Contract Security Classification Specification DFARS Defense Federal Acquisition Regulation Supplement DoD Department of Defense DSCA Defense Counterintelligence and Security Agency FAR Federal Acquisition Regulation GFP/M/E/S Government Furnished Property/Material/Equipment/Services HQDA Headquarters, Department of the Army HSPD Homeland Security Presidential Directive IA Information Assurance IS Information System(s) KO Contracting Officer NFPA National Fire Protection Association NGB National Guard Bureau OCI Organizational Conflict of Interest PII Personally Identifiable Information PIPO Phase In/Phase Out POC Point of Contact PRS Performance Requirements Summary PWS Performance Work Statement QA Quality Assurance QASP Quality Assurance Surveillance Plan QC Quality Control QCP Quality Control Program SCR Service Contract Reporting

CUI

SSN Social Security Number TE Technical Exhibit T.O. Technical Order USD(I) Under Secretary of Defense for Intelligence

3.0 Government Furnished Property. Material, Equipment and Services (GFP/M/E/S): The Government will provide the property, material, equipment, and/or services listed below solely for the purpose of performance under this contract:

3.1 Property. The Government will furnish the necessary workspace for the contractor to perform services outlined in this PWS.

3.2 Materials: None

3.3 Equipment: None

3.4 Services: None

3.5 Utilities: Exterior electric, exterior water. Contractor may use eye wash station, lavatory facilities and interior wash basins. The contractor shall operate under conditions that preclude the waste of utilities, which include turning off the water faucets or valves after using the required amount.

4.0 Contractor Furnished Property. Materials, and Equipment (CFP/M/E): Contractor will furnish all items necessary to comply with the requirements of NFPA 10, Chapter 7, 2026 edition.

4.1 General: Except for those items specifically stated to be Government-Furnished in Paragraph 3.0, the contractor shall furnish everything required to perform these services as indicated in Paragraph 1.1.

5.0 Requirements: The contractor shall: Comply with the maintenance requirements and frequencies of inspection IAW NFPA 10 Chapter 7.

5.1. Service the estimated quantities of fire extinguishers for annual maintenance IAW NFPA 10, Chapter 7, 2026 editions, for the following sizes and types.

CUI

5.1.1. 367 - 10-pound ABC Dry Chemical

5.1.2. 27 – 20–30-pound ABC Dry Chemical

5.1.3. 6 – 50-pound BC Dry Chemical

5.1.4. 8 – 5-pound Halon

5.1.5. 17 – 150-pound NOVEC Wheeled Units

5.1.6. 2 – Water

5.1.7. 2 – Class D Metal

5.1.8. 8 – Class K

5.2. Internal examinations of extinguishers will be conducted IAW the following intervals outlined in NFPA 10, Chapter 7, Table 7.3.3.1.

Table 7.3.3.1 Maintenance Involving Internal Examination

Extinguisher Type Internal Examination Interval (years)

Stored-pressure loaded stream and antifreeze 1 Pump tank water and pump tank, calcium chloride based

Dry chemical, cartridge- and cylinder-operated, with mild steel shells

Dry powder, cartridge- and cylinder-operated, with mild steel shells

Wetting agent 1 Stored-pressure water 5 Foam 3 Stored-pressure dry chemical, with stainless steel shells

Carbon dioxide 5 Wet chemical 5 Dry chemical stored-pressure, with mild steel shells, brazed brass shells, and aluminum shells

Halogenated agents 6

5.3. Annual External Examination of All Extinguishers.

CUI

5.3.1 Physical Condition. An annual external visual examination of all fire extinguishers shall be made to detect obvious physical damage, corrosion, or nozzle blockage to verify that the operating instructions are present, legible, and facing forward, and that the HMIS information is present and legible, and to determine if a 6-year interval examination or hydrostatic test is due.

5.3.2. Improperly labeled or marked fire extinguishers shall be replaced or removed from service until corrected.

5.3.3. Seals or Tamper Indicators. At the time of the maintenance, the tamper seal of a rechargeable fire extinguisher shall be removed by operating the pull pin or locking device.

5.3.4. After the applicable maintenance procedures are completed, a new listed tamper seal shall be installed.

5.3.5. Seals or tamper indicators on non-rechargeable-type extinguishers shall not be removed.

5.3.6. Boots, Foot Rings, and Attachments. All removable extinguisher boots, foot rings, and attachments shall be removed to accommodate thorough annual cylinder examinations.

5.3.7. Stored-Pressure Fire Extinguishers. When subjected to temperatures at or above their listed rating, stored-pressure fire extinguishers that require a 12-year hydrostatic test shall be emptied and subjected to the applicable maintenance and recharge procedures on an annual basis.

5.3.8 Corrective Action. When an external examination of any fire extinguisher reveals a deficiency, immediate corrective action shall be taken.

5.4 Annual Maintenance Record Keeping.

5.4.1 Each fire extinguisher shall have a tag or label securely attached that indicates that maintenance was performed.

5.4.2. The tag or label, as a minimum, shall identify the following:

(1) Month and year maintenance was performed

(2) Person performing the work

(3) Name and address of the agency performing the work https://link.nfpa.org/publications/10/2026/annexes/A/groups/7#ID000100000806 https://link.nfpa.org/publications/10/2026/annexes/A/groups/7#ID000100000806

CUI

5.4.3. Each extinguisher that has undergone maintenance that includes internal examination, shall have a verification-of-service collar located around the neck of the container.

5.4.3.1. This requirement does not apply to the Wheeled 150-pound Novec (5.1.5.) and 50-pound BC units (5.1.3.)

5.5. Extinguishers identified as required for 6-year maintenance will be serviced IAW NFAP 10, Chapter 7, para 7.3.6.

5.5.1. When the applicable maintenance procedures are performed during periodic recharging or hydrostatic testing, the 6-year requirement shall begin from that date.

5.5.2. The removal of agent from halon agent fire extinguishers shall only be done using a listed halon closed recovery system.

5.5.3. Non-rechargeable fire extinguishers shall not be required to have a 6-year internal examination and shall not be hydrostatically tested but shall be removed from service at a maximum interval of 12 years from the date of manufacture.

5.5.4. Non-rechargeable halon agent fire extinguishers shall be disposed of in accordance with 7.2.3.3 of NFPA 10, 2026 edition.

5.5.5. Corrective Action. When an internal examination of any fire extinguisher reveals a deficiency, immediate corrective action shall be taken.

5.5.6. Six-Year Internal Examination Label. Fire extinguishers that pass the applicable 6-year requirement shall have the maintenance information recorded on a durable weatherproof label that is a minimum of 2 in. × 31⁄2 in. (51 mm × 89 mm).

5.5.7. The new label shall be affixed to the shell by a heatless process, and any previous 6-year internal examination labels shall be removed.

5.5.8. These labels shall be of the self-destructive type when their removal from a fire extinguisher is attempted.

5.5.9. The 6-year internal examination label shall, as a minimum, identify the following:

(1) Month and year the 6-year internal examination was performed

(2) Person performing the work https://link.nfpa.org/publications/10/2026/chapters/7#ID000100000428

CUI

(3) Name of the agency performing the work

5.6. Extinguishers identified as required for 12-year maintenance will be taken out of service and the COR will be notified.

5.7. The contractor shall report ALL contractor labor hours (including subcontractor labor hours) required for performance of services provided under this contract for the 182d Airlift Wing Contracting Office via a secure data collection site.

5.8. The contractor shall completely fill in all required data fields using the following web address: https://sam.gov. Log in and select Entity Registrations and then select Service Contract Reporting.

5.9. The Contractor shall report the required information annually by October 31, for services performed under this contract during the preceding Government fiscal year (October 1- September 30).

The DoD Guidebook for Service Contract Reporting in SAM, available on the DoD Procurement Toolbox at https://dodprocurementtoolbox.com/site-pages/service-contract-reporting-scr. The General Services Administration (GSA) has also posted additional guidance such as quick start guides, informational videos, and frequently asked questions, that can be accessed by going to https://sam.gov and searching the “HELP” section. The SAM Federal User Guide is also available in the “HELP” section for comprehensive instructions on navigating SAM. Contractors requiring assistance using SAM should contact the Federal Service Desk at https://www.fsd.gov.

6.0 Applicable Publications: Publications applicable to this PWS are listed below:

Publication (Chapter/Page)

Date of Publication

Mandator y or

Advisory Website

Federal Acquisition Regulation https://www.acquisition.gov/?q=browsefar

Defense Federal Acquisition Regulation Supplement http://www.acq.osd.mil/dpap/dars/dfarspgi/c urrent/index.html or https://www.acquisition.gov/dfars

Joint Travel Regulation (JTR) https://www.defensetravel.dod.mil/site/travel reg.cfm https://dodprocurementtoolbox.com/site-pages/service-contract-reporting-scr https://www.fsd.gov/ https://www.acquisition.gov/?q=browsefar http://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html http://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html https://www.acquisition.gov/dfars

CUI

DoDM 1000.13-M-V1 DoD Identification (ID) Cards (Enclosure 2, paragraph 3.b)

01/23/201

(Change 1:

07/28/202

0) http://www.esd.whs.mil/Directives/issuances/ dodm

Federal Information Processing Standards (FIPS) Publication 201-

Personal Identity Verification (PIV) of Federal Employees and Contractors

(paragraph 9)

August http://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIP

S.201-2.pdf

DoDM 5200.2 Procedures for the DoD Personnel Security Program

(PSP)

04/03/201 https://www.esd.whs.mil/Directives/issuances

/dodm/

DoDI 5200.46 DoD Investigative and

Adjudicative Guidance for Issuing the Common Access Card (CAC)

09/09/14 (Change 1:

05/04/201

8)

/dodi/

Homeland Security Presidential Directive (HSPD)-12

Policy for a Common Identification Standard for Federal Employees and Contractors

08/27/200 https://www.dhs.gov/homeland-security-presidential-directive-12

DoDI 5400.11 Department of Defense Privacy and Civil Liberties Programs

01/29/201

/dodi/

DoD 5400.11-R Department of Defense Privacy

Program

05/14/200

DoDD 8140.01 Cyberspace Workforce

Management

10/05/202

/dodd/

DoD 8570.01-M Information Assurance Workforce

Improvement Program

12/19/200 5 (Change

4:

11/10/201

5) http://www.esd.whs.mil/Directives/issuances/dodm http://www.esd.whs.mil/Directives/issuances/dodm http://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.201-2.pdf http://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.201-2.pdf https://www.esd.whs.mil/Directives/issuances/dodm/ https://www.esd.whs.mil/Directives/issuances/dodm/ https://www.esd.whs.mil/Directives/issuances/dodi/ https://www.esd.whs.mil/Directives/issuances/dodi/ https://www.dhs.gov/homeland-security-presidential-directive-12 https://www.dhs.gov/homeland-security-presidential-directive-12 https://www.esd.whs.mil/Directives/issuances/dodi/ https://www.esd.whs.mil/Directives/issuances/dodi/ https://www.esd.whs.mil/Directives/issuances/dodd/ https://www.esd.whs.mil/Directives/issuances/dodd/ https://www.esd.whs.mil/Directives/issuances/dodm/ https://www.esd.whs.mil/Directives/issuances/dodm/

CUI

DoD 5220.22-M National Industrial Security Program Operating Manual

(NISPOM)

02/28/200

(Change 2:

05/18/201

6)

AFI 10-245

Antiterrorism

03/28/201

(Certified current

03/30/201 7) https://www.e-publishing.af.mil/Product-

Index/#/?view=pubs&orgID=10141&catID=1&s eries=-1&modID=449&tabID=131

AFI 31-101

Security Forces Standards and

Procedures

08/18/202 eries=-1&modID=449&tabID=131

AFMAN 31-113

Security Forces Standards and

Procedures

03/05/201

Change 1:

12/02/201 eries=-1&modID=449&tabID=131

AFPD 17-1

Information Dominance

Governance and Management

04/12/201 eries=-1&modID=449&tabID=131

AFMAN 17-1301

Computer Security (COMPUSEC)

02/12/202 eries=-1&modID=449&tabID=131

AFI 10-701

Operations Security

7/24/2019 (Change 1:

06/09/202

0) eries=-1&modID=449&tabID=131

6.1 Applicable Forms: Forms applicable to the PWS are listed below:

Form Date Website

DD 1172-2

Application for Identification Card/DEERS Enrollment

Mar 2017 http://www.dtic.mil/whs/directives/forms/index.htm https://www.esd.whs.mil/Directives/issuances/dodm/ https://www.esd.whs.mil/Directives/issuances/dodm/ http://www.dtic.mil/whs/directives/forms/forminfo/forminfopage2479.html http://www.dtic.mil/whs/directives/forms/forminfo/forminfopage2479.html http://www.dtic.mil/whs/directives/forms/index.htm

CUI

I-9 Employment Eligibility

Verification

10/21/201 https://www.uscis.gov/sites/default/files/files/form/i- 9.pdf

DD 441

Department of Defense Security Agreement

Feb 2020 http://www.dtic.mil/whs/directives/forms/dd/ddforms0 001-0499.htm

DD 250

Material Inspection and

Receiving Report

Aug 2000 https://www.esd.whs.mil/Directives/forms/dd0001_049 9/ https://www.uscis.gov/sites/default/files/files/form/i-9.pdf https://www.uscis.gov/sites/default/files/files/form/i-9.pdf http://www.dtic.mil/whs/directives/forms/dd/ddforms0001-0499.htm http://www.dtic.mil/whs/directives/forms/dd/ddforms0001-0499.htm https://www.esd.whs.mil/Directives/forms/dd0001_0499/ https://www.esd.whs.mil/Directives/forms/dd0001_0499/

TECHNICAL EXHIBIT 1

Performance Requirements Summary (PRS)

This PRS includes performance objectives the Government will use to determine contractor performance and will compare contractor performance to the Acceptable Quality Level (AQL).

Performance

Objective Performance Standard Acceptable Quality

Levels (AQL) Surveillance Method / By

Whom Annual

Maintenance (non-wheeled)

IAW NFPA 10, Chapter 7, 2026 edition

100% COR

6-Year Maintenance

IAW NFPA 10, Chapter 7, 2026 edition

100% COR

Annual Maintenance

(wheeled)

IAW NFPA 10, Chapter 7, 2026 edition

100% COR

TECHNICAL EXHIBIT 2

Deliverables Schedule

(Deliverables must be identified in the PWS and then summarized here. See examples below)

PWS Reference / Deliverable Title

Frequency Number of Copies

Medium/Format Submit To

Paragraphs 5.0 –

5.6 from PWS above At the time of service Per Unit

IAW NFPA 10,

Chapter 7, 2026 edition

Attached to Each Unit

TECHNICAL EXHIBIT 3

Estimated Workload Data

This information is provided for historical background only and not a guarantee of workload quantities.

ITEM NAME ANNUAL ESTIMATED QUANTITY

1 10-pound ABC 367 2 20-30-pound ABC 27 3 50-pound BC 6 4 5-pound HALON 8 5 150-pound Novec 17 6 Water 2 7 Class D 2 8 Class K 8