CAAA 2016001018 - SCC Washer Specs.doc
DOC document 27 KB Posted
- Attached to
- WASHERS/DRYERS - Request for Quote
- Solicitation number
- DQ1 CAAA 2016001018 1
- Issued by
- Grand County, Colorado
About this file
This is a specification document for a procurement of commercial laundry equipment by Skyline Correctional Center under California state contract CAAA 2016001018. The facility is seeking three open pocket washer-extractors with a minimum 60-65 pound dry load capacity. The washers must be delivered and installed at Skyline Correctional Center with connection to 240-volt, three-phase utilities. Key deliverables include inside delivery, professional installation by a qualified technician, on-site demonstration of operations and preventive maintenance procedures, and comprehensive documentation including installation, operations, and maintenance manuals with spare parts lists and wiring diagrams for each machine. A mandatory site visit is required prior to bidding. The specification document does not indicate response dates, due dates, award dates, or contract term information.
The specification establishes rigorous technical requirements for the washers, including Type 304 stainless steel construction, nine cubic feet minimum cylinder capacity, programmable microprocessor controls with minimum nine pre-selected programs, multi-speed extraction capabilities at 300g or higher, and built-in water conservation software designed to reduce consumption by 0.2 gallons or more per pound processed. Distributors must possess factory-certified, trained service technicians capable of providing repair service within 48 hours. The specification document provided contains no pricing information, set-aside details, incumbent information, funding sources, or contract amounts. Compliance with all applicable federal, state, and local laws, rules, regulations, and codes is mandatory.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| CAAA 2016001018 - SCC Dryer Specs.doc | DOC document | |
| CAAA 2016001018 - Washers & Dryers SCC.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Item:
Washer- Extractor, Open Pocket
Quantity:
Three (3) each at Skyline Correctional Center Pertinent Data:
60-65 pound capacity, Rigid Mount
Utilities Required:
240 volts, 3 phase
1. Washer shall have a minimum dry load capacity of 60 lbs.
2. Washer door opening shall be no less than 15 ½ inches diameter. Door glass is high tensile strength capable of withstanding thermal shock.
3. The shell door will be fitted with a locking device which shall prevent operation of the washer until the door is closed and locked. The locking device will prevent opening the door until the end of the cycle.
4. Type 304 corrosion resistant stainless steel shall be used for the entire shell and cylinder. All cylinder welds will be continuous.
5. Washer cylinder shall have a minimum capacity of nine (9) cubic feet.
6. Bearings shall be installed in an adequate bearing housing which shall be rigidly secured to the frame. The bearing shall be permanently lubricated and sealed heavy duty ball bearings.
7. The shaft will be alloy steel, major diameter not less than 2 ½ inches, ground and polished.
8. The washer shall be equipped with an out-of-balance vibration safety switch which, on excessive vibration during high speed extraction, will automatically stop or slow the washer.
9. Water inlet values shall be 3/4 inch commercial type, heavy brass, waterproof and mechanically protected coils with variable level control.
10. Washer shall be equipped with a 3 inch gravity drain valve, which opens automatically in case of power failure.
11. Washer shall be provided with programmable microprocessor capable of providing a minimum of nine (9) pre-selected programs. Pre-programmed and on-site programs can be erased or edited and new programs added to fit specific fabric and soil requirements.
12. Washer must have a water temperature display, management lockout for programming changes and advancing during cycle.
13. Washer shall be provided to accommodate owner-purchased liquid dispensing system.
14. Washer shall be equipped with the following features:
a. Multi-speed extraction, 300 g or higher at high extract speed
b. Variable-speed wash
15. Built in water saver software – features such as leak detection, 30 programmable water levels, reduced rinses, etc - to reduce water consumption by 0.2 gallons or more per pound processed, as compared to similar models without this software.
16. Must meet all applicable federal, state, and local laws, rules, regulations, and codes.
17. Quoted price will include inside delivery, installation and connection to adequate & accessible utilities by a qualified technician, and an on-site demonstration of machine operation and routine preventive maintenance procedures to Laundry and Maintenance staff member(s). A site visit is MANDATORY; see solicitation for instructions.
18. Distributor must have certified, factory trained Service Technicians that can provide repair service within 48 hours. The respective qualifications and experience of the bidders may be an evaluation factor in awarding this purchase
19. Manufacturer to provide a minimum of two installation, operations, and maintenance manuals, including spare parts lists, wiring diagrams, preventative maintenance, and any other pertinent data for each machine.
File details come from the government source that posted it. Updated .