C04c_Attachment 3_Product Data Sheets_12444326Q0047.pdf

Vent Stack Fan Model FAN-1

Startronics restroom solar powered vent stack exhaust fan Model FAN-1 has been designed to give restroom manufacturers a rugged yet simple product to promote air flow and not inhibit ordinary natural flow. This product has been extensively tested and exceeds all of the manufacturers conditions.

The following components are used:

Solar Module:

Rated Power 10 watts Current @ Max. Power 0.58 Voltage @ Max. Power 17.40 Short Circuit Amps 0.63 Open Circuit Voltage 21.70 Length (Inches) 12.0 Width (Inches) 13.86 Depth (Inches) 0.87

Fan:

Brushless DC Motor Electrical Protection: Impedance Protected Housing Material: Plastic UL 94 VO Impeller Material: Plastic UL 94 VO Voltage Range: 7-27.6 Input Power: 5.8 Watts Amperage: 0.24 Airflow: @ 24V 105.9 CFM Nominal Speed: 2600 RPM Protection Level for Humidity: IP54 or IP55 Rain Cap & Bottom Weep Holes Included Life Expectancy: 80,000 hours @ 40 Deg. C Operating Temp: -10 Deg. C +60 Deg. C

Support Bracket;

1/8” X 1.5” X 36” Aluminum Stainless Steel Fasteners

PHOTOS

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01 020811020020000329

PRODUCT DATA SHEET

DRYLOK® E1

Semi-gloss, latex-base, 1-part epoxy concrete floor paint

DESCRIPTION

DRYLOK® E1 is a semi-gloss high-performance coating for both commercial and residential use, DRYLOK® E1 is a latex based, 1-part epoxy concrete floor paint that utilizes an advanced epoxy ester resin fortified formulation to deliver greater protection and durabil-ity.

USES

Specially formulated to protect and beautify:

interior/exterior concrete floors▪ garage floors▪ basement floors▪ walkways▪ patios▪

CHARACTERISTICS / ADVANTAGES

Resists hot tire pick-up, chemicals, oil, grease, and gasoline stains

Formulated using Advanced Epoxy Ester Resin for a durable finish

Easy to maintain▪ Semi-gloss finish▪ Apply by brush or roller▪

1 / 6

PRODUCT INFORMATION

Composition Latex base

Packaging Size PC/Case Color Order No. Old Order No.

1 gal 2 Tint Base 832394 28413 1 gal 2 Gray 832392 23713 1 gal 2 Platinum 832393 23813

Shelf life 2 years in original unopened container

Storage conditions Store between 50°F (10°C) and 85°F (29°C). Extreme heat or freezing tem-peratures can damage the product, causing it to separate or thicken. Avoid Freezing. Keep away from direct sunlight.

Density Platinum 9.53 (LBS./US GAL.)

Gray 9.62 (LBS./US GAL.)

Tint Base 9.49 (LBS./US GAL.)

Wet Film Thickness 4-5 wet mils per coat pH-Value 8.0-9.0

Solid content Platinum 42.76% (by weight) Gray 43.51% (by weight) Tint Base 42.46% (by weight)

Viscosity 80 ± 3 KU

Appearance Semi-gloss finish Surface appearance depends upon condition and porosity of concrete/masonry surface. Highly porous ma-sonry/concrete may require additional coats to achieve full gloss.

TECHNICAL INFORMATION

Freeze thaw resistance Freeze/Thaw stable

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01 020811020020000329

2 / 6

APPLICATION INFORMATION

Number of Coats Max. 2

Coverage 300–400 ft2 (27.87–37.16 m2) per gallon (Recommended film thickness/coat: 4-5 wet mils/coat)

Ambient air temperature 50-90°F (10-32°C) during application and for a minimum of 4 hrs after ap-plication.

Substrate temperature 50-90°F (10-32°C) during application and for a minimum of 4 hrs after ap-plication.

Curing time Open Up To Light use (foot traffic) 4 hours Open Up To Heavy use (foot traffic) 24 hours Open Up To Vehicular traffic 5-7 days Max. Resistance Properties Reached 3-5 days

Drying time To touch 30 minutes-1 hour To recoat 4 hours

BASIS OF PRODUCT DATA

Results may differ based upon statistical variations de-pending upon mixing methods and equipment, tem-perature, application methods, test methods, actual site conditions and curing conditions.

LIMITATIONS

DRYLOK® E1 is recommended for light commercial, in-dustrial, and residential floors not coated with a 2-part epoxy.

ENVIRONMENTAL, HEALTH AND

SAFETY

For further information and advice regarding trans-portation, handling, storage and disposal of chemical products, user should refer to the actual Safety Data

Sheets containing physical, environmental, toxicologic-al and other safety related data. User must read the current actual Safety Data Sheets before using any products. In case of an emergency, call CHEMTREC at 1-800-424-9300, International 703-527-3887.

FIRST AID

EYES: Flush immediately with large amounts of water for at least 15 minutes. Consult a physician if irritation persists.

SKIN: Wash affected areas with soap and water. Con-sult a physician if irritation persists.

INGESTION: Give 1 or 2 glasses of water. If individual is drowsy or unconscious do not give anything by mouth.

Consult a physician, medical facility, or poison control center for advise about whether to induce vomiting.

INHALATION: Remove to fresh air.

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01

3 / 6

APPLICATION INSTRUCTIONS

SUBSTRATE PREPARATION

General Suface Preparation:

Surfaces must be thoroughly cleaned and free from dirt, dust, grease, oil, soap, wax, concrete curing mem-branes, and the oily film left by sweeping compounds.

Stains on the surface should be removed using a heavy duty detergent until the surface is clean. Rinse thor-oughly with clean water and allow to dry completely.

If using a pressure washer, do not use a setting above 1750 PSI to avoid damaging the concrete. Surface must be xompletely dry before painting. To verify the surface is completely dry and free of residual trapped moisture, tape a 1ft. by 1ft. square piece of plastic onto the surface and let stand for 24 hours. If mois-ture is present on the concrete side of the plastic, the surface has not dried sufficiently. Allow additional dry-ing and retest. Surface porosity is important for prop-er product adhesion. Before application, test concrete porosity by sprinkling a few drops of water onto the surface in several areas. If water is readily absorbed, you are ready to paint. If it beads or lays on the sur-face, additional cleaning and etching is required. Refer to “ACID ETCHING INSTRUCTIONS” below.

Old/Weathered, or Previously Painted Surfaces Pre-paration:

Remove peeling paint and clean (see “General Surface Preparation” above). Mildew should be removed using a suitable mildew remover. Allow to dry completely.

Glossy painted surfaces must be dulled or sanded to improve adhesion. Do not apply to floors previously painted with 2 component epoxy paints/coatings. For bare surfaces that are highly troweled or smooth, acid etching is required. Refer to “ACID ETCHING INSTRUC- TIONS” below. Do not etch painted surfaces.

New/Unpainted Surfaces, Garage Floors, Exterior Con-crete Preparation:

New concrete must cure for 30 days. For best results, new concrete should be washed and scrubbed thor-oughly to remove any surface contaminants. Allow to dry completely. All surfaces subject to vehicle traffic, highly troweled or extremely smooth concrete, must be acid etched. Refer to “ACID ETCHING INSTRUC- TIONS” below.

SUBSTRATE QUALITY / PRE-TREATMENT

ACID ETCHING INSTRUCTIONS

Do not etch painted surfaces. Acid etching will dissolve certain minerals in the top layer of concrete, creating a more porous surface for improved adhesion. To etch concrete, predampen the entire surface then use DRYLOK® Concrete and Masonry Etch & Cleaner ac-cording to label directions. Apply until the surface has the look and feel of 150-grit sandpaper. The acid etch-ing process may be repeated until the proper texture is achieved.

Test the concrete’s porosity by sprinkling a few drops of water on the surface. If the water droplets do not readily penetrate into the prepared concrete, addi-tional acid etching is required. All residual acid must be removed from the surface. Rinse thoroughly and al-low to dry (see “To Check for Trapped Moisture” above) prior to application of the DRYLOK® E1.

On areas that have had efflorescence (saltlike deposit) problems or exposure to excess levels of salt com-pounds, it is recommended that DRYLOK® Concrete Protector be applied according to label directions prior to application of the DRYLOK® E1.

WARNING

If you scrape, sand, or remove old paint, you may re-lease lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN

DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WO-

MEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Be-fore you start, find out how to protect yourself and

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01

4 / 6 your family by contacting the National Lead Informa-tion Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

MIXING

Mix two gallons of the same color paint together to ensure uniform color and avoid shade variations.

APPLICATION

STIR THOROUGHLY BEFORE AND DURING APPLICA-

TION. Air and surface temperature must be between 50°-90°F (10°-32°C) during application and for a min-imum of 4 hours after application.

For exterior surfaces, do not apply if rain is expected within 24 hours. Wait for a dry, rain-free period. DO NOT THIN. Apply an even coat using a 3/8” (9.525

mm) nap roller or nylon/polyester brush. Do not paint in direct sunlight or apply to a hot surface. Provide good ventilation for normal drying. Allow first coat to dry 4 hours prior to applying the second coat. High hu-midity and low temperatures may require longer dry-ing times. The second coat should be applied in a cross direction to the first coat to achieve color uniformity.

Do not apply more than 2 coats. When using 2 or more containers of the same color of DRYLOK® E1, mix together to assure color uniformity.

NOTE: Painted surfaces may become slippery when wet. If a slip resistant surface is desired add 2-4 oz.

(59-118 mL) of DRYLOK® Non-Skid Texture Additive per gallon to DRYLOK® E1.

IMPORTANT

Floors that are subjected to hydrostatic pressure (wa-ter seeping from underneath the floor) or are continu-ally damp cannot be satisfactorily painted with any paint or coating. Moisture on basement floors caused by water seeping through masonry walls or through floor-wall joints or cracks must first be eliminated. Use DRYLOK® Fast Plug®, a quick setting hydraulic cement, to fill floor-wall joints or cracks. If the basement floor is subjected to hydrostatic pressure, use DRYLOK® Floor & Wall Masonry Waterproofer to control water.

Then, apply DRYLOK® E1 per label directions. In addi-tion, outside work may be required to eliminate water infiltration.

LEGAL DISCLAIMER

• KEEP CONTAINER TIGHTLY CLOSED

• KEEP OUT OF REACH OF CHILDREN

• NOT FOR INTERNAL CONSUMPTION

Prior to each use of any product of Sika Corporation, its subsidiaries or affiliates (“SIKA”), the user must al-ways read and follow the warnings and instructions on the product’s most current product label, Product Data Sheet and Safety Data Sheet which are available at www.drylok.com or by calling SIKA’s Technical Ser-vice Department at 1-800-272-3235, option 2. Nothing contained in any SIKA literature or materials relieves the user of the obligation to read and follow the warn-ings and instructions for each SIKA product as set forth in the current product label, Product Data Sheet and

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01

5 / 6

Safety Data Sheet prior to use of the SIKA product.

SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties on the current Product Data Sheet if used as directed within the product’s shelf life. User determines suitability of product for intended use and assumes all risks. User’s and/or buyer’s sole remedy shall be limited to the pur-chase price or replacement of this product exclusive of any labor costs. NO OTHER WARRANTIES EXPRESS OR

IMPLIED SHALL APPLY INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEG-

AL THEORY FOR SPECIAL OR CONSEQUENTIAL DAM-

AGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE

OF THIS PRODUCT IN A MANNER TO INFRINGE ON

ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY

RIGHTS HELD BY OTHERS.

Sale of SIKA products are subject to the Terms and Conditions of Sale which are available at https://usa.sika.com/en/about-us/terms-conditions-of-sale.html or by calling 1-800-272-3235, option 2.

DRYLOKE1-en-USDRYLOK-(09-2025)-1-1.pdf

PRODUCT DATA SHEET

DRYLOK® E1

September 2025, Version 01.01

6 / 6

7/25/2019

DAP® DYNAFLEX® 920 PREMIUM

EXTERIOR ELASTOMERIC SEALANT

DAP® DYNAFLEX® 920 PREMIUM EXTERIOR ELASTOMERIC SEALANT is a high performance, solvent-based, elastomeric sealant developed for professional siding and window installations. It provides a long-lasting elastomeric seal which helps to prevent water and air intrusion. The extensive offering of colors provides an aesthetically appealing finished look to any installation. It can be applied to wet/damp surfaces and in extreme weather conditions. It will not wash out when exposed to rain prior to full cure.

Crackproof, waterproof and weatherproof. Paintable and self-tooling. Meets ASTM C920, Class 25. Exterior use.

• Meets ASTM C920, Class 25

• Adheres to wet/damp surfaces

• Applies at temperatures as low as 20°F

• Extremely flexible – crack proof

• Waterproof & weatherproof

• Self-tooling

• Paintable after cure

• Excellent UV stability

• Exterior use

• MasterSpec Section 07900 Weatherproof Sealants

PACKAGING COLOR UPC

10.0 fl oz (296 mL)

White

(WT098)

7079889200

10.0 fl oz (296 mL)

Colors (All) 7079889(+ 3-digit Color #)

PRODUCT DESCRIPTION

KEY FEATURES & BENEFITS

7/25/2019

USE FOR EXTERIOR WEATHERIZATION SEALING APPLICATIONS SUCH AS:

• Windows

• Doors

• Siding

• Exterior trim

• Gutters

• Flashing

• Pipes

• Vents

• Ducts

ADHERES TO:

• Wood – painted & unpainted

• Vinyl

• Most plastics

• Aluminum

• Most metals

• Fiber cement

• Concrete

• Mortar

• Brick

• Stone

• Glass

• Ceramic

• Fiberglass

• Stucco

• Most common building materials

• Application temperature range is between 20ºF and 120ºF.

• Not for butt joints less than ¼” wide or joints exceeding ½” wide x ½” deep. If joint depth exceeds ½”, use foam backer rod.

• Recommended bead size: 1/4” to 3/8”

• Apply a convex sealant bead to joint ensuring sealant contacts both surfaces. Avoid gaps in sealant bead, fill joint and avoid tooling. Natural shrinkage during cure will leave a flat or concave bead.

• Not recommended for continuous underwater use, below grade applications, or for surface defects.

• Store below 80°F in dry place for optimal shelf life.

Surface Preparation Surface must be clean, dry, structurally sound and free of old caulk, dirt, dust & other contamination.

Product Application

1. Cut nozzle tip to allow for a minimum ¼” bead size.

2. Load cartridge into caulk gun. Apply pressure to burst foil seal inside spout.

3. Fill gaps and cracks with sealant.

4. Clean up excess wet sealant from surface and tools with mineral spirits. Scrape or cut away excess dried sealant. Do not use mineral spirits to clean hands or skin. Wash hands or skin with soap and water.

5. Paintable after fully dried through (7 to 14 days), depending on temperature & humidity.

SUGGESTED USES

FOR BEST RESULTS

APPLICATION

3/7/2019

Typical Uncured Physical Properties

Appearance/Consistency Gunnable, non-sag paste

Base Polymer Synthetic rubber

Filler Calcium carbonate

Volatile Exempt solvents

Weight % Solids 70.8%

Density (lbs per gallon) 10

Odor Strong solvent

Flash Point >98ºF

Freeze Thaw Stability (ASTM C1183) Will not freeze

Shelf Life 24 months

Coverage 31 linear feet at 1/4” diameter bead, 14 linear feet at 3/8” diameter bead

Typical Application Properties

Application Temperature Range 20ºF to 120ºF

Tooling Time (Working Time) 5 minutes

Tack Free Time 5 minutes

Full Dry Through 7-14 days

Vertical Sag (ASTM D2202) 0.05”

Typical Cured Performance Properties

Service Temperature Range No data available

Paint Ready Time 7-14 days

Mildew Resistance Cured sealant is mold & mildew resistant

Dynamic Joint Movement (ASTM C719) +/-25%

Remove excess uncured sealant from surfaces and tools with mineral spirits. Excess cured sealant must be cut or scraped away. Do not use mineral spirits to clean hands or skin. Wash hands or skin with soap and water. Store container in temperatures below 80ºF and in a dry place.

TYPICAL PHYSICAL & CHEMICAL PROPERTIES

CLEAN UP & STORAGE

3/7/2019

See product label or Safety Data Sheet (SDS) for health and safety information. You can request a SDS by visiting our website at dap.com or calling 888-DAP-TIPS.

WARRANTY: If product fails to perform when used as directed, within one year of date of purchase, call

888-DAP-TIPS, with your sales receipt and product container available, for replacement product or sales price refund. DAP Products Inc. will not be responsible for incidental or consequential damages.

Manufacturer: DAP Products Inc., 2400 Boston Street, Baltimore, Maryland 21224

Usage Information: Call 888-DAP-TIPS or visit dap.com & click on “Ask the Expert”

Order Information: 800-327-3339 or orders@dap.com

Fax Number: 410-558-1068

Also, visit the DAP website at dap.com

SAFETY

WARRANTY

COMPANY IDENTIFICATION