BID 70CNR-S2821 - PROJECT OVERVIEW AND SPECS.pdf

BID 70CNR-S2821

NEVADA STATE PARKS

1. PROJECT OVERVIEW

Nevada Division of State Parks (NDSP) is replacing one (1) double wide manufactured home at the Cave Lake State Park (CLSP).

2. VENDOR RESPONSIBILITIES AND REQUIREMENTS

2.1 The vendor shall have experience, expertise, and resources to fabricate a new manufactured home, and deliver it to the project site. This includes, but is not limited to design, construction, and delivery.

2.2 A minimum of three years’ experience in similar manufacture and installation of manufactured home type structures.

2.3 The vendor shall provide a minimum;

2.3.1 fabrication and delivery

2.3.1.1 Manufactured home to be delivered to site.

2.3.1.2 Manufactured home to be set on existing 24’-0” x 48’-0” concrete raised foundation. Set By Other

2.4 All manufactured home drawings must be stamped and appropriate for the unit type when drawings are submitted for review and approval.

2.5 Manufactured homes shall be certified by the Nevada Housing Division

Manufactured Housing (MHD), Recreational Vehicle Industry Association (RVIA). The vendor shall provide all required design drawings for approval to MHD, RVIA, and NDSP as appropriate for the Park Manufactured home type.

2.5.1. The vendor will be responsible for MHD and or RVIA submission. The

NDSP Project Manager will review the Vendor’s submitted drawings and calculations as needed.

2.6 Manufactured home shall be designed to meet Nevada State Fire Marshal

Requirements.

2.6.1 Fire detection and suppression to be per MHD or RVIA code as appropriate for the Park Manufactured home type. Per ANSI A119.5 automatic fire suppression system is required. Models regulated by

Nevada Housing.Division or State Public Works Division will require an automatic fire suppression system.

3. NDSP RESPONSIBILITIES OF THE PROJECT

3.1 NDSP will provide access to the site for truck delivery, sufficient area for installation, and equipment to perform the contract requirements with the park as designated by the Project Manager.

3.2 NDSP will coordinate Park entry on the day(s) the manufactured home is to be delivered and set

4. MANUFACTURED HOME SPECIFICATIONS AND CONSTRUCTION –

GENERAL REQUIRMENTS

4.1 Vendor to use floor plan and elevations from Clayton Homes Dream Series DRM481A 2448 as the basis of design. See Floor Plan attached to this specification.

4.1.1 Energy Efficient home to follow the Clayton Home “Energy Smart Zero” as the basis for design.

4.1.1 Manufactured home elevations to have a standard manufactured home appearance with a recessed entrance.

4.2 Vendor will provide all labor, material, equipment, services and permits as may be required by the State of Nevada and or local jurisdictions. This shall include all Transport Permits if required.

4.3 Vendor to provide the Wind Speed, and Ground snow load specification for the manufactured homes per ANSI 119.5.

4.3.1 Wind Speed:__________________________________

4.3.2 Ground Snow Load:____________________________

4.4 Prior to delivery, the vendor or their designated contractor shall verify roadway, building site access, all existing field conditions. NDSP will assist the vendor with site access information

4.5 Vendor to ensure the operation functionality of all supplied equipment and appliances once utility connections are made.

4.6 Vendor to revise documents as required by NDSP. NDSP requires the following drawings;

4.6.1 Floor plan;

4.6.1.1 Code information, exiting, interior, and exterior dimensions, doors, windows, finishes, and manufactured home etc.;

4.6.1.2 Will include mechanical, plumbing, and electrical locations

4.6.1.3 Roof plan;

4.6.1.4 Exterior elevations;

4.6.1.5 Mechanical, plumbing, and electrical sheets;

A. As required to define the products and systems.

4.7 Transport, deliver and install the Park Manufactured homes a designated by NDSP.

The manufactured homes shall be delivered per approved plans;

4.8 All products and services provided under a contract shall be in strict conformance with all applicable county, state, and federal codes, rules, regulations, and guidelines;

4.9 Each manufactured home in its entirety shall be guaranteed for one year from date of acceptance, which covers labor and materials. This includes, but is not limited to, the new park manufactured home. All other warranties shall apply, including but not limited to; roofing, HVAC systems, furnishings, appliances, and other manufacture’s warranties and or guarantees;

4.10 Provide hardwired electrical connection to power main and approve plumbing connection to site sewer and water connection services;

4.10.1 Final connection by other

4.12 The vendor and NDSP provide a final walk of each manufactured home, as well as submit to NDSP two (2) sets of close out documents. Close out documents shall include all written warranties for all materials and equipment, maintenance manuals for equipment and product listing (including, but not limited to paint color numbers, HVAC equipment, etc.). Close out shall also include: 1 gallon of each paint/sealer product used.

5. NOT USED

6. Manufactured Home Specifications – Exterior

6.1 2” x 6” exterior stud construction at perimeter

6.2 R-21 batt insulation

6.3 ½” plywood shear

6.4 vapor barrier

6.4.1 vapor barrier basis of design is Tyvek Homewrap or equal.

6.5 siding to be lap cement board

6.5.1 basis of design to be Hardie Plank Lap Siding – Select Cedarmill

6.5.1.1 Thickness: 0.312, Length: 144” board, Width: 8.25”

6.6 Primer and Paint body and trim

6.6.1 all joints and trim to be caulked

6.7 Roofing to be metal

6.7.1 24 Gauge, Standing Seam Metal Roof – Colonial Red

6.7.2 synthetic roofing underlayment. UDL 30 or equal.

6.7.3 overhang to be 14 inches

6.7.4 roofing fascia to be rough sawn.

6.7.5 venting per IRC requirements

6.7.6 roof pitch: 3:12

6.7.7 snow load design 60 lbs.

6.7.8 climate zone 5B

6.8 Windows

6.8.1 triple pane vinyl

6.8.2 Low-E

6.8.3 color to be grey.

6.8.4 insect screens

6.8.5 2” faux mini blinds

6.9 Doors

6.9.1 exterior doors to be 36” x 80” x 1-3/4” six panel 18-gauge metal insulated.

Frame to be 16 gauge.

6.9.2 exterior doors to include deadbolt with lockset (Schlage)

6.9.3 primed and painted.

6.10 GFI Outlets – two locations

6.10.1 weatherproof cover

6.11 Hose Bibs – two locations

6.12 exterior elements to meet Wildland Urban Interface (WUI) requirements.

6.13 entry to be recessed.

7. Manufactured Home Specification – Foundation

7.1 Concrete foundation and stem wall is existing – Foundation Ready

7.2 install 6 MIL vapor barrier – entire crawl space – by other.

7.3 sill sealer at top of stem wall – by other.

7.4 crawl space venting per IRC requirements

7.5 Undercarriage Protection: Provide exterior grade heavy duty polyethylene vapor barrier.

8. Manufactured Home Specifications – Exterior Utilities

8.1 Gas – Propane

8.2 Electric

8.2.1 200-amp panel

8.3 Water

8.3.1 whole house water shutoff

8.4 Sewer

9. Manufactured Home Specifications – Interior Utilities (Appliances)

9.1 gas (propane) range – stainless steel

9.1.1 Frigidaire model number: FFGF3054TS

9.1.1 matching hood with built-in microwave – stainless steel

9.1.1.1 vent through side wall

9.2 electric dishwasher – stainless steel

9.2.1 Frigidaire model number: FFCD2413US

9.3 dryer connection to be gas (propane)

9.3.1 dryer connection to be prepared with 220V outlet.

9.3.2 dryer vent to be recessed.

9.4 electric garbage disposal

9.5 provide gas (propane) connection for refrigerator.

9.6 provide water connection for refrigerator ice maker.

10. Manufactured Home Specifications – Interior

10.1 walls to be ½” drywall.

10.1.1 textured – orange peel or equivalent

10.1.2 prime and paint

10.2 Ceiling

10.2.1 ceiling to be 5/8” drywall.

10.2.2 textured – brocade style

10.2.3 R-40 insulation

10.3 Flooring

10.3.1 flooring through the house to be laminate.

10.3.2 Abrasion Criteria scale to be AC4 set by NALFA.

10.3.3 8mm felt or foam underlayment.

10.3.4 2-inch baseboards

10.3.5 air register to be adjustable – brown.

10.3.6 R-33 insulation

10.3.7 Decking: ¾” x 4’ x 8’ sturdy-floor plywood installed with seams offset, glue and screw at 6” o.c. in the field, and 4” o.c. at the perimeter.

10.4 Doors

10.4.1 hollow core six panel doors

10.4.2 prime and paint

10.5 Cabinets – kitchen/bathroom

10.5.1 Shaker Style – Color: Smokey Mt. Grey

10.5.2 Hardwood

10.5.2.1 drawers

10.5.2.2 overhead cabinets

10.5. 2..3 base cabinets

10.5.2.4 cabinet back panel

10.5.3 cabinets over the refrigerator

10.5.4 glides to be heavy duty ball bearing.

10.5.5 Hardware cabinet knobs

10.5.6 bathrooms to have mirrors at each lav.

10.5.7 bathrooms towel and tissue bars

10.5.8 countertops to be laminate with matching edge – Wilsonart Spring Carnival

10.5.9 backsplash to be subway tile – Desert Grey

11. Manufactured Home Specifications – Mechanical, Plumbing and Electrical

11.1 Water Heater

11.1.1 gas (propane)

11.1.2 50 gallons

11.2 Furnace

11.2.1 gas (propane)

11.2.2 basis of design: Carrier

11.2.3 thermostat: Ecobee smart thermostat

11.2.4 air registers to be adjustable - brown.

11.3 Wood Stove

11.3.1. corner hearth.

11.4 Air Conditioner (heat pump)

11.4.1 heat pump ready 220V outlet

11.4.2 entire house to be AC/Ready

11.5 Fire Sprinkler System

11.5.1 Including the RD13 Residential Riser

11.5.2 Not including the backflow and electric hot box.

11.5.3 under kitchen sink fire extinguisher.

11.6 Electrical

11.6.1 manufactured home to meet Energy Star standards for electrical.

11.6.2 Service: 120/240-volt, single phase, 3 wire, 60 Hz grounded system with surge protection.

11.6.3 Panel Board: 200 amp

11.6.4 lighting

11.6.4.1 6” can light throughout.

11.6.4.2 bedrooms to have central ceiling fan/light with double switched.

11.6.4.3 bathrooms to have exhaust fan/light combination.

11.6.5 hardwire smoke alarm with CO detector – battery backup. Bedrooms and hallway

11.7 Kitchen Plumbing Fixtures

11.7.1 garbage disposer – ½ hp Frigidaire FFD1501 DMS

11.7.2 faucet kit to be stainless steel single lever with sprayer.

11.7.3 sink to be stainless steel self rimming.

11.8 Master Bathroom Plumbing Fixture

11.8.1 Metal Faucet

11.8.2 Sink to be China.

11.8.3 elongated toilet

11.8.4 Shower enclosure to be 60” fiberglass.

11.9 Guest Bathroom Plumbing Fixture

11.9.1 Metal Faucet

11.9.2 Sink to be China.

11.9.3 elongated toilet

11.9.4 Shower/Tub enclosure to be 60” fiberglass.

End of Document