Attachment 6 - IDPs.pdf

7510-00-082-2521 UI: DZ

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

IAW CID A-A-113D, DATED DECEMBER 4, 1996

TAPE, PRESSURE-SENSITIVE ADHESIVE

ITEM NAME TAPE, PRESSURE SENSITIVE ADHESIVE

I.A.W. TYPE: I - GLOSSY FINISH

CLASS: A - TRANSPARENT CELLULOSE ACETATE,

POLYOLEFIN, OR UNPLASTICIZED POLYVINYL CHLORIDE FILM

BACKING

OVERALL WIDTH 0.500 INCHES

OVERALL LENGTH 12.50 YARDS

OVERALL CORE DIAMETER 1.000 INCHES

USAGE FORM ROLL

OVERALL COLOR NATURAL

OVERALL MATERIAL PLASTIC

MATERIAL TRANSPARENCY CLEAR

SURFACE LUSTER LUSTERLESS

ADHESIVE LOCATION ONE SIDE

CUTTING DISPENSER INCLUDED

PACKAGING/PACKING

UNIT PACKAGING: Twelve (12) rolls of tape on dispensers shall be placed in a plastic bag, box or wrap of the type normally used commercially for this item. The rolls shall be packaged to prevent fusion, using the manufacturer's standard practice. The box, bag or wrap shall be secured to prevent accidental opening during shipment, handling, storage and redistribution.

PACKING: Twelve (12) unit packages shall be packed in a close-fitting shipping container in accordance with normal commercial practice, totaling 144 rolls per container. The complete shipping container shall be in compliance with Uniform Freight Classification and National Motor Freight Classification.

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive

Type II: Extendable

Age on Delivery: 4 Months

Shelf Life Code: 6 (24 Months Extendable Shelf Life)

Tapes shall be delivered within four (4) months after the manufacture date and have a shelf life of twenty-four (24) months after the manufacture date. After twenty-four (24) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF-LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R _151007.pdf

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

7510-00-958-0743 UI: HD

CLIP, PAPER

DESCRIPTION

ITEM NAME CLIP, PAPER

OVERALL LENGTH 2.000 INCHES

OVERALL THICKNESS 0.450 INCH GAUGE MIN TO 0.500 INCH GAUGE MAX

OVERALL COLOR SILVER

OVERALL MATERIAL STEEL

SURFACE LUSTER SMOOTH

USAGE DESIGN SIZE JUMBO

ENVIRONMENTAL PROTECTION CORROSION RESISTANT

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-377-8162 UI: BX

PORTFOLIO

DESCRIPTION

ITEM NAME PORTFOLIO

OVERALL WIDTH 9.000 INCHES

OVERALL LENGTH 11.50 INCHES

ACCOMMODATED SHEET WIDTH 8.500 INCHES

ACCOMMODATED SHEET LENGTH 11.00 INCHES

OVERALL EXTENSION LENGTH 19.00 INCHES

OVERALL THICKNESS 0.393 INCH

OVERALL SHEET CAPACITY 100 SHEETS

OVERALL COLOR BLACK

OVERALL MATERIAL LAMINATED KRAFT PAPER

COVER MATERIAL HEAVY WEIGHT LEATHERETTE STOCK

COVER SURFACE LUSTER GLOSSY

POCKET QUANTITY 2

POCKET LOCATION 1/2 LENGTH POCKET ON INSIDE FRONT AND BACK COVER

OPENING SIDE QUANTITY 3

SPECIAL FEATURE INNER DIE-CUT PORTION HOLDS A BUSINESS CARD

TIE STRING NOT INCLUDED

SLIDE FASTENER NOT INCLUDED

RING BINDER NOT INCLUDED

UNIT PACKAGE TYPE BOX

UNIT PACKAGE QUANTITY 25 FOLDERS PER BOX

PACKAGING/PACKING: Twenty-five (25) folders shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-411-6323 UI: EA

MAP CASE

DESCRIPTION

ITEM NAME MAP CASE

OVERALL WIDTH 13.50 INCHES

OVERALL LENGTH 13.50 INCHES

OVERALL COLOR WOODLAND GREEN CAMO

OVERALL MATERIAL NYLON AND VINYL

CLOSURE TYPE ZIP CLOSURE

SPECIAL FEATURE DUST PROOF

ENVIRONMENTAL PROTECTION WATER PROOF

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-425-6768 UI: RO

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

IN ACCORDANCE WITH COMMERCIAL ITEM DESCRIPTION A-A-1684C, DATED JULY 24, 1997.

TAPE, PRESSURE-SENSITIVE ADHESIVE (PLASTIC FILM)

ITEM NAME TAPE, PRESSURE SENSITIVE ADHESIVE

OVERALL WIDTH 2.000 INCHES

OVERALL LENGTH 330.0 FEET

OVERALL CORE DIAMETER 3.000 INCHES

OVERALL THICKNESS 0.001 INCHES

UNIT TYPE PACKAGING TAPE

USAGE FORM ROLL

OVERALL COLOR NATURAL

OVERALL MATERIAL PLASTIC

MATERIAL TRANSPARENCY CLEAR

ADHESIVE LOCATION ONE SIDE

MINIMUM TENSILE STRENGTH 20 PSI

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive

Type II: Extendable

Age on Delivery: 2 Months

Shelf Life Code: 4 (12 Months Extendable Shelf Life)

Tapes shall be delivered within two (2) months after the date of manufacture and have a shelf life of twelve (12) months after the date of manufacture. After twelve (12) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF-LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-495-0698 UI: EA

BINDER, LOOSE-LEAF

ITEM NAME BINDER, LOOSE-LEAF

ACCOMMODATED SHEET LENGTH 11.00 INCHES

OVERALL CAPACITY 5.000 INCHES

MINIMUM SHEET CAPACITY 900 SHEETS (USING 20 LB BASIS WEIGHT BOND PAPER)

UNIT TYPE NONSEPARABLE

UNIT DESIGN OVERLAY ON FRONT COVER, BACK COVER, AND SPINE

COVER DESIGN RIGID

COVER COLOR BLACK

COVER MATERIAL PLASTIC, VINYL OVER FIBERBOARD

COVER OPENING LOCATION SIDE

ITEM SECURING DEVICE TYPE D-RING

RING QUANTITY 3

LOCKING DEVICE END LEVER

INSIDE POCKETS INCLUDED

INSIDE POCKETS LOCATION FRONT AND BACK

SHEET HOLDING BAR INCLUDED

TITLE SLOT INCLUDED

TECHNICAL CHARACTERISTICS:

- Rings shall be made of steel with a minimum thickness of 0.090 inch and minimum hardness of R30T63 in accordance with ASTM E 18.

- The back plate shall have a minimum thickness of 0.018 inch.

- The operating mechanism cover plate shall have a minimum thickness of 0.012 inch.

- The lever that opens rings shall have a minimum thickness of 0.030 inch.

- The metal hinge shall have a minimum thickness of 0.020 inch.

- Exposed metal parts shall be corrosion resistant in accordance with normal commercial practice.

- The binder shall be bound with plastic 0.012 inch thick minimum, and having a Tear Resistance of 300 pound force per inch minimum in accordance with ASTM-D-1004, or equivalent commercial method.

- The cover board shall have a minimum thickness of 0.10 inch, and a minimum Basis Weight of 325 pound mass per 1000 square feet in accordance with TAPPI-T-410, or equivalent commercial method.

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

(paperboard). If paperboard is used in the manufacture of the item, the contractor shall certify that the paperboard used in the manufacture of the item contains a range of 75 - 100% post consumer material, including a range of 90 - 100 % recovered material in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:

www.epa.gov/epawaste/conserve/tools/cpg/index.htm

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory requirement (Plastic Covered Binders): The contractor shall certify that the product offered shall include a minimum range of 25 - 50 % recovered plastic material in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:

www.epa.gov/epawaste/conserve/tools/cpg/index.htm

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-649-1225 UI: EA

CARTRIDGE, TONER

ITEM NAME CARTRIDGE, TONER

I.A.W. HEWLETT PACKARD P/N CF330X

CARTRIDGE TYPE NEW (OEM GENUINE)

SPECIAL FEATURE HIGH YIELD CARTRIDGE FOR USE WITH HP LASERJET

ENTERPRISE PRINTER M651 PRINTERS AND ANY OTHER

PRINTER THAT USE HP P/N CF330X

COLOR BLACK

YIELD 20,500 PAGES (AVERAGE YIELD IAW ISO/IEC 19752)

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R _151007.pdf

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal

Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

STORAGE INSTRUCTIONS: To maximize the life of the laser printer toner cartridges, it is highly recommended that this item be stored between 5 to 32.2 Deg. C (41 to 90 Deg. F) and between 10 to 90% relative humidity (temperature/humidity-controlled conditions).

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-658-7385 UI: EA

CARTRIDGE, EXCESS TONER

ITEM NAME CARTRIDGE, EXCESS TONER

I.A.W. HEWLETT PACKARD P/N CF287X (HP 87X)

SPECIAL FEATURES HIGH YIELD CARTRIDGE FOR USE WITH HEWLETT PACKARD

LASERJET ENTERPRISE PRINTER SERIES INCLUDING M506, PRO M501, MFP M527, FLOW MFP

M527 SERIES AND ANY OTHER PRINTER USING HP P/N CF287X (HP 87X)

YIELD 18,000 BLACK PAGES (AVERAGE YIELD IAW ISO/IEC 19752)

protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R _151007.pdf

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

STORAGE INSTRUCTIONS: To maximize the life of the laser printer toner cartridges, it is highly recommended that this item be stored between 5 to 32.2 Deg. C (41 to 90 Deg. F) and between 10 to 90% relative humidity (temperature/humidity-controlled conditions).

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-662-7114 UI: EA

I.A.W. LEXMARK P/N 84C0HCG

SPECIAL FEATURES HIGH YIELD CARTRIDGE FOR USE WITH LEXMARK

LASERPRINT CX725 SERIES AND ANY OTHER PRINTER

USING LEXMARK P/N 84C0HCG

THIS IS A RETURN PROGRAM CARTRIDGE AND MUST BE

RETURNED TO LEXMARK AFTER USE FOR RECYCLING

COLOR CYAN

YIELD 16,000 PAGES (AVERAGE YIELD IAW ISO/IEC 19798)

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

SHELF LIFE

ITEM: Laser Toner Cartridges

Type II: Extendable

Age on Delivery: 9 Months

Shelf Life Code: 7 (36 Months Extendable Shelf Life)

The LaserJet cartridges shall be delivered within nine (9) months after the manufacture date, and have a shelf life of thirty-six (36) months after the manufacture date. After thirty-six (36) month, the Government reserves the right to extend the shelf life at its discretion.

STORAGE INSTRUCTIONS: To maximize the shelf life of the LaserJet cartridge, it is highly recommended that this item be stored between 5 to 32.2 Deg. C (41 to 90 Deg. F) and between 10 to 90% relative humidity temperate conditions.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each unit package and intermediate container shall be marked with the date of manufacture and/or expiration/inspection date, as applicable.

shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD129R _151007.pdf

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

This item is Government unique and includes the suffix letter "G" in the part number.

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-662-7118 UI: EA

I.A.W. LEXMARK P/N 84C0HYG

SPECIAL FEATURES HIGH YIELD CARTRIDGE FOR USE WITH LEXMARK

LASERPRINT CX725 SERIES AND ANY OTHER PRINTER

USING LEXMARK P/N 84C0HYG

THIS IS A RETURN PROGRAM CARTRIDGE AND MUST BE

RETURNED TO LEXMARK AFTER USE FOR RECYCLING

COLOR YELLOW

YIELD 16,000 PAGES (AVERAGE YIELD IAW ISO/IEC 19798)

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

SHELF LIFE

ITEM: Laser Toner Cartridges

Type II: Extendable

Age on Delivery: 9 Months

Shelf Life Code: 7 (36 Months Extendable Shelf Life)

The LaserJet cartridges shall be delivered within nine (9) months after the manufacture date and have a shelf life of thirty-six (36) months after the manufacture date. After thirty-six (36) month, the Government reserves the right to extend the shelf life at its discretion.

STORAGE INSTRUCTIONS: To maximize the shelf life of the LaserJet cartridge, it is highly recommended that this item be stored between 5 to 32.2 Deg. C (41 to 90 Deg. F) and between 10 to 90% relative humidity temperate conditions.

SHELF-LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each unit package and intermediate container shall be marked with the date of manufacture and/or expiration/inspection date, as applicable.

For Civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery

This item is Government unique and includes the suffix letter "G" in the part number.

commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market.

The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which

7510-01-662-7119 UI: EA

I.A.W. LEXMARK P/N 84C0HKG

SPECIAL FEATURES HIGH YIELD CARTRIDGE FOR USE WITH LEXMARK

LASERPRINT CX725 SERIES AND ANY OTHER PRINTER

USING LEXMARK P/N 84C0HKG.

THIS IS A RETURN PROGRAM CARTRIDGE AND MUST

BE RETURNED TO LEXMARK AFTER USE FOR

RECYCLING.

YIELD 25,000 PAGES (AVERAGE YIELD IAW ISO/IEC 19752)

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling, and storage. The

Uniform Freight Classification and shall not be more than 51 pounds in weight.

SHELF LIFE

ITEM: Laser Toner Cartridges

Type II: Extendable

Age on Delivery: 9 Months

Shelf Life Code: 7 (36 Months Extendable Shelf Life)

The LaserJet cartridges shall be delivered within nine (9) months after the manufacture date and have a shelf life of thirty-six (36) months after the manufacture date. After thirty-six (36) month, the Government reserves the right to extend the shelf life at its discretion.

STORAGE INSTRUCTIONS: To maximize the shelf life of the LaserJet cartridge, it is highly recommended that this item be stored between 5 to 32.2 Deg. C (41 to 90 Deg. F) and between 10 to 90% relative humidity temperate conditions.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each unit package and intermediate container shall be marked with the date of manufacture and/or expiration/inspection date, as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

This item is Government unique and includes the suffix letter "G" in the part number.

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal

7520-00-246-2664 UI: EA

FRAME, FILE DRAWER

ITEM NAME FRAME, FILE DRAWER

TOP WIDTH 12.688 INCHES

BOTTOM WIDTH 11.875 INCHES

OVERALL DEPTH 27.000 INCHES

OVERALL HEIGHT 9.3750 INCHES

FILE SIZE LETTER

OVERALL MATERIAL STEEL

ASSEMBLY METHOD SCREWDRIVER AND PLIERS

SPECIAL FEATURES WITH BREAK OFF NOTCHES TO SHORTEN SIDE RAIL

4.000 INCH LENGTH NOTCHED PORTION AT 0.500 INCH

INTERVALS

FRAME SIDE RAILS APPLICATION DESIGNED TO PROMOTE SLIDING OF THE FILE

FOLDERS

FRAME SIDE RAILS TYPE SNAP-OFF NOTCHED IN .500 INCHES TO 1.00 INCHES

INCREMENTS TO ADJUST THE LENGTH OF THE RAILS

FROM 13.00 INCHES TO 27.00 INCHES

DEPTH VARIANCE FROM 13.00 INCHES TO 27.00 INCHES (+/- 0.125 IN.)

DEPTH ADJUSTMENTS BEFORE "SNAP-OFF" SHALL BE NOT LESS THAN 26.0

INCHES

RAIL SAG ALLOWANCE SHALL NOT SAG OR BEND MORE THAN 0.250 INCHES

WHEN 11 EVENLY SPACED SUSPENDED FILE FOLDERS,

EACH HOLDING 200 SHEETS OF 75 G/SQ.M. (20 LB. 17 X

22-500) BOND PAPER ARE SUSPENDED FROM THE

FRAME

ENVIRONMENTAL PROTECTION A/A CORROSION RESISTANT COATING

practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

first receiving activity. The pack shall comply with the rules and regulations applicable to the

Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade. Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment.

Additionally, shipments delivered to DOD distribution facilities or freight consolidation points

RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS

COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE

HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to…