Attachment 5 - Barricuda 6096 Cut Sheet and Schematics.pdf

January 26, 2018 www.qualitymandm.com • sales@qualitymandm.com

4280 E 14th Street, Des Moines, Iowa 50313

(515) 266-2268 • Fax: (515) 266-0243

Barracuda I Model 6096 Fish Cleaning Station

Barracuda Intelligent Control System:

Either green button starts grinder and basin rinse.

Adjustable timers automatically stop grinder and rinse at the same time. After a brief pause, the rinse resumes long enough to flush all wastes through your drain. Your patrons can’t leave the grinder or water running!

1st Jam Release ™ reverses and halts the grinder on initial contact with foreign object to minimize cutter damage.

Either red button immediately stops the grinder, pressing it twice also stops basin rinse.

Displays daily, monthly and cumulative usage.

Housed in NEMA 4X enclosures.

Standard Features:

Heavy-duty, dual-shaft waste grinder

Exclusive dual 6½" inlet protects both your patrons and the grinder

¾" Sanalite cutting boards that slope to central drainage basin

Side-mounted, 60" x 19" x 34" high

ADA-compliant cutting table

Two Start/Stop control stations

Adjustable flow, automatic basin rinse

Four 60" side-mount spray hoses

Four 120V GFCI convenience outlets

Welded T304 stainless steel cabinet with adjustable leveling feet

Lockable doors and removable front panel for maintenance access

Shipped fully assembled

Grinder Specifications:

2HP/230VAC motor

29:1 gear ratio

Counter-rotating, 60 RPM shafts with

15 hardened cutters

Discharge adapter for 6" PVC pipe

Requirements:

30A/240VAC, 1 or 3-phase service

(no add-on converter required)

50-60 PSI, 1 inch water supply line

(2 to 10 GPM usage)

Available Options:

Hanging, overhead spray hoses

Hide-away, top-mount spray hoses

Cold-weather insulation package

Lockable winter cover

Discharge adapter for 4" PVC pipe http://www.qualitymandm.com/

Notes:

1. Cutting board surfaces are sloped to drain into the basin.

2. Exact elevations depend on leveling feet adjustments.

3. Other dimensions accurate to within 1/2 inch.

60"

1 2"

2 "

4 "

20 " 20 "

4 "

Front RearLeft Right

158 "

3"

FS6096-B1-EBarracuda I 6096 Exterior Views Quality Machine & Manufacturing

Scale: 1:32 Rev: 4D Eng: JDB 01/29/18Ckd: PJW

18"

2"

2"

12"

4"

Notes:

1. Sufficient space must be provided for manuevering the FCS into position (and removing/reinstalling the grinder if needed) from the front, access-door side of the cabinet.

2. The customer is responsible for providing the equipment needed to unload and install the FCS.

3. All positioning dimensions are shown relative to the station's vertical centerline, which aligns with the centers of the grinder inlet and discharge ports.

4. All utility lines should project through a pre-installed concrete pad as indicated, to avoid conflicts with the grinder and the depicted cabinet members.

5. Center a 6" waste pipe (6.625" O.D.) beneath the station's intended position:

a. An adapter for sealing the grinder outlet to a 6" PVC pipe is normally provided. Please inform

QM&M well in advance if you need a different type of waste discharge adapter.

b. The customer is responsible for providing and installing any needed trap or clean-out.

c. When installing the FCS, the waste line must be trimmed to protrude 4.625 ± 0.125" above the bottoms of the cabinet's leveling feet.

d. We suggest that you install that pipe with a flanged end or coupler barely projecting above the concrete surface, so that you can later insert the necessary length of pipe between it and the grinder discharge.

6. Install an earth ground and a single- or three-phase, 30 amp (minimum), 240VAC service line through the pad in the indicated Electrical Line Area. In either case, that line must include a neutral but does not need a grounding conductor.

7. Install a water supply line through the pad in the indicated Water Line Area:

a. Said line should be capable of maintaining a 50 psig pressure and 10 gallon per minute flow

(minimum), measured at the pad.

b. The 1" NPT inlet shutoff valve can be rotated as indicated to facilitate its connection to that line.

c. Position the water line far enough from the cabinet side to facilitate tightening its connector.

1" FNPT Inlet Shutoff Valve

2 "

Waste Line

Electrical Line Area

Water Line Area

4"

5"

4"

4"

8" 7"

Breaker Box (14" Ground Clearance)

4"

R7"

4"

VFD

Control Panel (mounted on door)

FS6096-B1-SBarracuda I 6096 Site Requirements Quality Machine & Manufacturing

Scale: 1:32 Rev: 4D Eng: JDB 01/29/18Ckd: PJW