Attachment 3 - Kaeser Enclosure Drawing.pdf
PDF 1 MB Posted
- Solicitation number
- Not on record
About this file
This is a technical proposal drawing for an industrial compressed air system installation. The document presents a layout design prepared in accordance with NEC standards for a complete system configuration including two BSD 50 compressors, a 120-gallon wet receiver, a 240-gallon dry receiver, a KAD 260 air dryer with filter pack B, a KCF 200 cooling unit, and a 480V electrical panel with step-down transformer for single-point connection. The design incorporates thermostatically controlled inlet louvers and recirculating louvers with backflow prevention for cooling air management, wall heaters, access doors, and a service door. The system requires 4-foot clearance on all sides for service and ventilation, with additional clearance recommended for forklift and rear-access service operations. Total dimensions are 336 inches by 126 inches based on the layout specifications.
The proposal includes a detailed three-dimensional isometric view and multiple floor plan perspectives showing equipment placement and airflow management. Key specifications note that all site work, including site preparation and construction of system components, falls under the installer's responsibility. The document emphasizes compliance with occupational health and safety regulations and requires proper handling and treatment of condensate discharge in accordance with all local and state laws. A SAM 4.0 unit is recommended, and a 480V electrical disconnect is optional. The drawing was reviewed and released on 12/11/2019 and includes manufacturer information from Kaeser Kompressoren.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
1 2 3 4 5 6 7 8
1 2 3 4 5
A
B
C
D
E
F
A
B
C
D
E
Template Rev. 05.03.2019
12/11/2019
12/11/2019 refaia
Kemph
1 of 1Page
Layout Drawing Enclosure, (2) BSD 50, (2) KAD 260, SAM 4.0, KCF 200 / KCI-USA
12/11/2019 Manzke
Sketch
LYUS0193600Sketch
PI
Paper size
Project No.
Status
Rev. Modification Date Name Original Replaces Replaced by
Drawing Review
Released
Date Name
ANSI C / 1:50
Description
PROPOSAL
P&I Diagram
All site work, including but not limited to, site preparation, construction, system component assembly and installation, must be completed in accordance with all relevant local, state and national codes and regulations, including but not limited to, building, electrical and occupational safety. End-users and all sub-contractors responsible for this work may be provided with product information to initiate these tasks, however this is not a substitution for reading and understanding the appropriate Product Manuals prior to installation of the equipment. Since the compliance with the various federal, state and local laws and regulations concerning occupational health and safety and pollution are affected by the use, installation and operation of Equipment and other matters over which Kaeser has no control, Kaeser assumes no responsibility for compliance with those laws and regulations, whether by way of indemnity, warranty or otherwise.
Station Setup ID Station ID
Documents released by engineering are identified by these characteristics in the title block:
Date of review/ release and name of the reviewing/ releasing individual.
Layout Drawing 12/11/2019 refaia
All dimensions are in inches
Thermostatically controlled inlet louvers
This drawing was prepared in accordance with NEC standards
Thermostatically controlled recirculating louver with back flow prevention
Recommended clearance dimensions for service and proper ventilation are 4ft on all sides (additional clearance is recommended for forklift/service access on the rear)
Additional civil preparations at the site location are the responsibility of the user
Condensate discharge must be handled and treated in accordance with all local and state laws
Overview
BSD 50 BSD 50
KAD 260
w/Filter pack B
(2 Places)
120 Gallon Receiver (Wet)
240 Gallon Reciver (Dry)
KCF 200
480V Electrical Panel w/ step down transformer (single point connection)
120"336"
126"
Exhaust air via thermostatically controlled fan
Cooling Air Exhaust
Cooling Air Inlet
Enclosure base to include lifitng eyes, grounding lugs, and environmental barrier
Cooling air inlet via thermostatically controlled louvers (2 places)
Cooling air exhaust via duct with thermostatically controlled recirculation louvers
Wall Heater (2 Places)
1x BSD 50 Standby
SAM 4.0
(Recommended)
480V Electrical Disconnect (Optional)
Access Door Access Door
Service Door
Typical (May not reflect equipment being quoted)
File details come from the government source that posted it. Updated .