Attachment 2 - Statement of Work.pdf

502 CONS/JBKAE

JBSA Lackland, TX 30 June 2023 FA301623U0185

Security Camera System

Statement of Work (SOW)

Security Camera Refresh, JBSA Lackland AFB, TX 78236

1000 FEMOYER ST - BLDG 10800

950 FEMOYER ST - BLDG 10802

1050 FEMOYER ST - BLDG 10806

1435 Metzger Drive - BLDG 10504

1.0 DESCRIPTION OF WORK

The contractor shall provide all personnel, equipment, supplies, tools, materials, and non-personal services necessary to install security camera system as defined in this Statement of

Work (SOW). This stand-alone security camera system shall not touch the Air Force network.

There shall be no classified, or sensitive data used with the stand-alone security camera system.

The new security camera system will replace the current system in all buildings and will use the existing approved wiring that is already in place from the previous system. There shall be no unmarked cables at any places in the system. Marking codes used on cables shall correspond to the codes shown on system drawings. In addition, upon completion, vendor shall provide training and instructions of proper use of system, backup, and camera usage.

Project Locations:

The work shall be located at JBSA Lackland Bldg. 10800, 10802, 10806, and 10504 as defined in this SOW.

2.0 DESCRIPTION OF WORK:

2.1 The work required includes the design, delivery and full installation of the security monitoring system. The contractor shall provide, install and configure all necessary equipment for a security monitoring system.

2.2 All cameras shall be of sufficient quality to be able to see in low/no light. The outside cameras shall be protected in an all-weather, wind, rain, and hail protective shell.

2.3 The four 55-inch LED monitors and two workstations shall be located in BLDG 10800 Rm

189 mounted on the north wall. The four monitors shall be installed in the existing location of the existing monitors. The monitors shall be 51” above the floor.

2.4 The system shall include two Network Video Recorders in BLDG 10802, and placed in the existing network racks on the east wall of the office. The room is located on the right as you walk in the entrance to the building. The NVR’s shall have the capability of recording

Security Camera System

24/7/365 days a year, and shall store video feeds for no less than 30 days with a capability to store to an external hard drive or DVD/CD.

2.5 The system shall include two Network Video Recorders in BLDG 10806, and placed in the existing network racks on the east wall of the office. The room is located on the right as you walk in the entrance to the building. The NVR’s shall have the capability of recording

24/7/365 days a year, and shall store video feeds for no less than 30 days with a capability to store to an external hard drive or DVD/CD.

2.6 The contractor shall use the existing network rack on the floor to maintain the two desktop computers located in BLDG 10800 Rm, 189. The contractor shall use the one existing network rack, network switch, and uninterruptible power (UPS) supply located on the on the east wall in BLDG 10800.

2.7 The contractor shall use the existing connection lines for the camera inputs in BLDG 10802 and 10806. The contractor shall ensure the connections for the cameras convert from Bayonet

Neill–Concelman (BNC) to Power over Ethernet (PoE) to the network switches.

2.8 The contractor shall use the network rack and existing connection between BLDG 10800 to

10802 and 10806.

2.9 Building 10504 will have a stand-alone security monitoring system. There shall be no classified, or sensitive data used with the stand-alone security monitoring system. The work shall be located at JBSA Lackland Bldg. 10504 as defined in this SOW.

2.10 The system shall include a NVR recorder located in Rm 125, with the capability of recording 24/7/365 days a year, and shall store video feeds for no less than 30 days with a capability to store to an external hard drive or DVD/CD. The LED monitors shall be located in the Admin Office, Rm 105 mounted against the west wall where the previous monitors were located. The cameras shall have a clear view at night, and zoom in options. The audio video control system requires display/playback capabilities. The system shall consist of the following;

NOTE: Contractor’s proposed equipment and supplies are not limited to the following list based on proposed design.

3.0 Specifications: All specification are approximate:

3.1 121 (EA) Enterprise Edition camera connection license - Bldg. 10800, 10802, 10806

Manufacturer: Avigilon

Part Number: ACC7-ENT

(Brand Name of Equal)

3.1.1 Supports 75 connections

3.1.2 Software supports multiple actions on camera notifications.

3.1.3 Dual Streaming for Open Network Video Interface (ONVI) compliant cameras.

3.1.4 Supports H.265, H.264, MPEG4. MJPEG, JPEG2000 video compression.

3.2 (4 EA) Network Video Recorder - Bldg. 10802/10806

Part Number: NVR4X-STD-48TB-NA

3.2.1 48 Terabyte (TB)

3.2.2 2 Universal Rack Mount

3.2.3 Recording Mode Real Time

3.2.4 Simultaneous live, recording and playback

3.2.5 Recording system Hard Disk Drive

3.2.6 Storage capacity 48 TB

3.2.7 Resolution 7K (30 Mega Pixel)

3.2.8 Expandable to multi–Network Video Recorder

3.2.9 Voltage 100 ~ 240 Voltage Alternate Current

3.2.10 Power consumption watts (W) 270 ~ 750

3.2.11 Weight 34.5 Lbs.

3.2.12 Dimensions 18.98 x 3.41 x 29.4 inches

3.2.13 Preloaded with video management software

3.3 (2 EA) Workstation - Bldg. 10800

3.3.1 Double Data Rate 4 Synchronous dynamic random-access memory

3.3.2 Processor Type Core i3

3.3.3 Standard Memory 8 Gigabit (GB)

3.3.4 Ethernet Technology GB Ethernet

3.3.5 Operating System standard Enterprise

3.3.6 Input Voltage 120 V Alternate Current (AC), 230 V AC

3.3.7 Environmental Certification Restriction of Certain Hazardous Substances

3.3.8 Remote Monitoring Workstations 5th Generation

3.3.9 Universal Serial Bus Keyboard

3.3.10 Universal Serial Bus Mouse

3.3.11 Mini Tower, DVD-RW

3.3.12 2 Gigabit Ethernet RJ-45 ports (1000Base-T)

3.3.13 2 x Multicast Dissemination Protocol to Display Port Adapters

3.3.14 2 x Multicast Dissemination Protocol to High-Definition (HD) Multimedia

Interface Adapters

3.3.15 Depth 292 mm

Manufacturer: Avigilon

Part Number: RM5-WKS-2MN-NA

Security Camera System

3.3.16 Form Factor Small Form Factor

3.3.17 Height 290 mm

3.3.18 Weight 11.59 lbs.

3.3.19 Width 92.6 mm

3.3.20 4K SUPPORT Supports full 4K video streaming

3.3.21 Supports High-Definition Cameras

3.4 (58 EA) Surface Mount Indoor Dome Camera - Bldg. 10800, 10802, 10806

3.4.1 Color Type Color / Monochrome

3.4.2 Resolution 4 Megapixel

3.4.3 Indoor Type

3.4.4 Mount Type Surface

3.4.5 Electrical Specifications Voltage: 12 Volts Direct Current (DC) / 24 Volts

Alternate Current (AC)

3.4.6 Supports Power over Ethernet

3.4.7 Power Consumption: 13 W

3.4.8 Focal length 3.3 ~ 9 mm

3.4.9 Compression H.264 H.265 High-Definition Stream Management Smart Codec

3.4.10 Smart Codec, Motion JPEG

3.4.11 Back Light Compensation

3.4.12 White Balance

3.4.13 Electronic Shutter range Automatic, Manual (1/7 to 1/8196 sec)

3.4.14 Network Properties Interface: 100BASE-TX, RJ45 Connector, CAT5e Cabling

3.4.15 Supports standard multiple network protocols

3.4.16 Image Frame Rate: 25 frame per second (FPS)/30 fps

3.4.17 Dimensions mm: 163 x 163 x 118

3.4.18 Weight 2 lbs.

3.4.19 Protection: Internet Protocol (IP) 66, IP67, IK10.

3.4.20 True Wide Dynamic Range

3.5 (63 EA) Outdoor Bullet Camera Bldg. 10800, 10802, 10806

Part Number: 4.0C-H5A-B01-IR

3.5.1 Chip Inch Size 1/2.8

3.5.2 Color Type Color / Monochrome

3.5.3 Resolution 4MP

3.5.4 Electrical Specifications Voltage: 12Volts DC C, 24Volts AC

3.5.5 Power over Ethernet

3.5.6 Power Consumption: 13 W

Manufacturer: Avigilon

Part Number: 4.0C-H5A-D1-IR

Security Camera System

3.5.7 Motion Activated

3.5.8 Mount Type Surface

3.5.9 Wide Dynamic Range

3.5.10 Network Properties Image Frame Rate: 25 fps/30 fps

3.5.11 Interface: 100BASE-TX, RJ45 Connector

3.5.12 Supports multiple standard network protocols

3.5.13 Back Light Compensation

3.5.14 White Balance Support

3.5.15 Electronic Shutter Range Automatic, Manual (1/7 to 1/8196 seconds)

3.5.16 Zoom Support

3.5.17 Compression Type H.264m H265 High-Definition Streaming Management

3.5.18 Smart Codec, Motion Joint Photographic Experts Group

3.5.19 Dimensions mm: 280 x 126 x 91

3.5.20 True Wide Dynamic Range

3.5.21 Supports mounted devices in a pendant or surface mount configuration

3.6 (63EA) Junction box Bldg. 10800, 10802, 10806

Part Number: H4-BO-JBOX1

3.6.1 Low profile junction box

3.6.2 Supports High-Definition Bullet Cameras

3.6.3 2x 3/4” (NTP) cable entry holes for cable connections

3.6.4 Meets Inter Protocol 66 weather rating

3.6.5 Weight: 1.30 lbs.

3.6.6 Finish: Powder coated aluminum, European color matching system 9003

3.7 (4 EA) 4K Ultra High Definition (HD) 55” Premium LED Monitor Bldg. 10800

Manufacturer: Orion

Part Number: 4K55DH DN

3.7.1 Screen Size (Diagonal) 54.6"

3.7.2 Resolution 3840 x 2160

3.7.3 Bit Depth / Color Support 10-Bit (1.07 billion colors)

3.7.4 Brightness 500 one candelas per square meter

3.7.5 Viewing Angle (H x V)178 x 178°

3.7.6 Aspect Ratio 16:9

3.7.7 Contrast Ratio 1100:1

3.7.8 Response Time 8 millisecond

3.7.9 Horizontal Frequency 60 to 75 kHz

3.7.10 Vertical Frequency 55 to 75 Hz

3.7.11 Backlighting Technology

3.7.12 Input Ports 1 x DisplayPort Video

Security Camera System

3.7.13 1 x HD Multimedia Video

3.7.14 1 x 1/8" / 3.5 mm Audio

3.7.15 1 x 15-Pin Video Graphics Array Video

3.7.16 Output Ports 1 x DisplayPort – Video

3.7.17 1 x HD – Video

3.7.18 1 x Digital Video Disk – Video

3.7.19 1 x 1/8" / 3.5 mm – Audio

3.7.20 Universal Serial Bus Ports 1

3.7.21 Universal Serial Bus Ports Type-A - Service

3.7.22 Control Infrared, Recommended Standard-232C via DE-9/DB-9

3.7.23 Other I/O 1 x RS-232C Control Input

3.7.24 1 x RS-232C Control Output

3.7.25 Built-In Speakers 2 x 1 W

3.7.26 Power Consumption Operational: < 125.0 W

3.7.27 Alternate Current Input Power 100 to 240 VAC, 50 / 60 Hz

3.8 (4 EA) Universal Low Profile wall mount Bldg. 10800

Manufacturer: Orion

Part Number: WB-4663

3.8.1 Supported Screen Sizes 37 to 65"

3.8.2 Weight Capacity 165 lb.

3.8.3 Mounting-Hole Pattern 80 x 58

3.8.4 Tilt Adjustment -10 to +0°

3.8.5 Orientation Landscape

3.8.6 Distance from Mounting Surface 1.77"

3.8.7 Wall Plate Size 34.02 x 7.99"

3.8.8 Dimensions 34.02 x 17.32 x 1.77"

3.9 (5 EA) Smart Managed Power over Ethernet + Switch Bldg. 10800

Manufacturer: Transition Networks

Part Number: SM24TAT2SA

3.9.1 Connectors (24) 10/100/1000 RJ-45 ports (2) 100/1000 SFP slots

3.9.2 Protocols Carrier-sense multiple access

3.9.3 Store-and-Forward switching architecture

3.9.4 Media Access Control (MAC) 8K MAC address table

3.9.5 Backplane 52 Gbps

3.9.6 Dimensions: Width: 17.4” Depth: 8.3” Height: 1.73”

3.9.7 Power Input 100-240 Volts Alternate Current

3.9.8 Power Consumption 438 Watts

3.9.9 PoE Budget 370 Watts 30 Watts for (12) ports simultaneously

Security Camera System

3.9.10 PoE Budget 15.4 Watts for (24) ports simultaneously

3.9.11 Surge Protection 6 kilo volts

3.9.12 Weight 6.6 lbs.

3.9.13 Internet Protocol Pv6 Access Management

3.9.14 Support Jumbo Frame up to 9Kbytes

3.9.15 Terminal Access Controller Access-Control System

3.9.16 Dynamic Host Configuration Protocol Relay

3.9.17 Dynamic Host Configuration Protocol support

3.9.18 L2/L3/L4 Access Control Lists

3.9.19 Supports MAC

3.9.20 Supports Access Control List

3.9.21 Internet Protocol standard/extended Access Control List

3.9.22 Link Layer Discovery Protocol

3.9.23 Institute of Electrical and Electronics Engineers 802.3az Energy Efficiency

3.9.24 Internet Protocol Source Guard, Port Security

3.10 7,500 (FT) CAT6e plenum cable Bldg. 10800, 10802, 10806

Manufacturer: AIS

Part Number: CAT6e Plenum

3.10.1 Type Ethernet

3.10.2 Connectors RJ45s and Keystone Jacks

3.10.3 Specifications 23 American Wire Gauge

3.11 (121 EA) Indoor Camera Installation Kit Bldg. 10800, 10802, 10806

Manufacturer: AIS

Part Number: CKI-CAT6-G

3.11.1 Category 6E PDCC

3.11.2 23 AWG

3.11.3 Solid soft drawn bare copper conductor.

3.11.4 Low smoke plenum rated insulation.

3.11.5 Different lays and a central separator

3.11.6 Minimize for cross-talk interference.

3.11.7 Low smoke plenum rated jacket

3.11.8 Unshielded Cat6 RJ45

3.11.9 Plug with Load-Bar

3.11.10 Adaptable Solid or Stranded conductor

3.11.11 4-pair Cat6 cable

3.11.12 Staggered nose pattern

3.12 (121 EA) IP PoE Powered Video Balun- Bldg. 10800, 10802, 10806

Manufacturer: EverFocus

Security Camera System

Part Number: PALUN-II

3.12.1 Maximum connection distance of 1148ft / 350m

3.12.2 Automatic 802.3at & af PoE detection

3.12.3 Automatic Medium Dependent Interface (MDI) /MDI-X detection

3.12.4 Low network signal attenuation

3.13 (1 EA) Engineering, Installation and Commissioning Services – All buildings

3.13.1 The contractor shall use the existing locations of the previous cameras.

3.14. The cameras shall be located in the following areas in BLDG 10800.

3.15 Outdoor Cameras

3.15.1 Camera One, 4 MP Bullet camera, NW corner building.

3.15.2 Camera Two, 4 MP Bullet camera, NW corner of building.

3.15.3 Camera Three, 4 MP Bullet camera on the NE corner of building.

3.15.4 Camera Four, 4 MP Bullet camera East center of building.

3.15.5 Camera Five, 4 MP Bullet camera SE corner of building

3.15.6 Camera Six, 4 MP Bullet camera, SE corner of building.

3.15.7 Camera Seven, 4 MP Bullet camera, SW corner of building.

3.15.8 Camera Eight, 4 MP Bullet camera, West corner of building.

3.16 Indoor Cameras

3.16.1 Camera Nine, 4 MP Dome Camera, North exit of building,

3.16.2 Camera Ten, 4 MP Dome Camera, center of building, next to Rm B199D

3.16.3 Camera 11, 4 MP Dome Camera, center of building, next to men’s restroom.

3.16.4 Camera 12, 4 MP Dome Camera, NW corner of briefing room.

3.16.5 Camera 13, 4 MP Done Camera. NE corner of briefing room.

3.16.6 Camera 14, 4 MP Done Camera, SW corner of the briefing room.

3.16.7 Camera 15, 4 MP Done Camera, SE corner of the briefing room.

3.16.8 Camera 16, 4 MP Done Camera, SW corner of the monitor room.

3.17 The cameras shall be located in the following areas in BLDG 10802.

3.18 BLDG 10802, 1st Floor Outside Cameras

3.18.1 Camera One, 4 MP Bullet Camera, NW corner of building.

3.18.2 Camera Two, 4 MP Bullet Camera, NW corner of building.

3.18.3 Camera Three, 4 MP Bullet Camera, NW outside wall of stairs.

3.18.4 Camera Four, 4 MP Bullet Camera. NW outside wall of stairs.

3.18.5 Camera Five, 4 MP Bullet Camera. North outside exit door.

Security Camera System

3.18.6 Camera Seven 4 MP Bullet Camera, NE corner of building.

3.18.7 Camera Eight, 4 MP Bullet Camera, NE corner of building.

3.18.8 Camera Nine, 4 MP Bullet Camera, East corner center of building.

3.18.9 Camera Ten, 4 MP Bullet Camera, South corner center of building

3.18.10 Camera 13, 4 MP Bullet Camera. SW inner corner wall.

3.18.11 Camera 14, 4 MP Bullet Camera, outside East corner wall.

3.18.12 Camera 15, 4 MP Bullet Camera, outside SE corner.

3.18.13 Camera 16, 4 MP Bullet Camera, outside SE corner close to the front of the building

3.18.14 Camera 17, 4 MP Bullet Camera, outside SE corner close to the front of the building

3.18.15 Camera 21, 4 MP Bullet Camera, South indent of building next to entrance.

3.18.16 Camera 22, 4 MP Bullet Camera. SE corner indent of building next to entrance.

3.18.17 Camera 23, 4 MP Bullet Camera. SW corner wall.

3.18.18 Camera 24, 4 MP Bullet Camera, West corner wall.

3.18.19 Camera 25, 4 MP Bullet Camera, West corner wall.

3.18.20 Camera 26, 4 MP Bullet Camera. West wall,

3.18.21 Camera 27, 4 MP Bullet Camera, under West stairwell exit.

3.18.22 Camera 29, 4 MP Bullet Camera. West corner wall.

3.18.23 Camera 30, 4 MP Bullet Camera. SW inner corner wall.

3.19 BLDG 10802, Inside Cameras

3.19.1 Camera Six, 4 MP Dome Camera, North hallway.

3.19.2 Camera 11, 4 MP Dome Camera, South hallway.

3.19.3 Camera 12, 4 MP Dome Camera, North wall in break area.

3.19.4 Camera 18, 4 MP Dome Camera, inside West stairwell.

3.19.5 Camera 19, 4 MP Dome Camera, inside SW main entrance room.

3.19.6 Camera 20, 4 MP Dome Camera, inside East hallway.

3.19.7 Camera 28, 4 MP Dome Camera. Inside West hallway.

3.19.8 Camera 31, 4 MP Dome Camera inside Office SE corner of office.

3.20 BLDG 10802, 2nd Floor

3.21 Outside Cameras

3.21.1 Camera One, 4 MP Bullet Camera, North outdoor exit of building.

3.21.2 Camera 11, 4 MP Bullet Camera, West outdoor exit of building.

3.22 Inside Cameras

3.22.1 Camera two, 4 MP Dome Camera, north exit hallway

3.22.2 Camera three, 4 MP Dome Camera, south exit hallway.

3.22.3 Camera four, 4 MP Dome Camera, NE ceiling laundry room.

3.22.4 Camera five, 4 MP Dome Camera, inside NW hallway foyer.

Security Camera System

3.22.5 Camera six, 4 MP Dome Camera. East ceiling laundry room.

3.22.6 Camera seven, 4 MP Dome Camera, SE outside laundry room entrance.

3.22.7 Camera eight, 4 MP Dome Camera, above West stairwell entrance.

3.22.8 Camera nine, 4 MP Dome Camera, inside East hallway.

3.22.9 Camera ten, 4 MP Dome Camera, inside West hallway.

3.23 BLDG 10802, 3rd Floor

3.24 Outside Cameras

3.24.1 Camera One, 4 MP Bullet Camera, North outdoor exit of building.

3.24.2 Camera 11, 4 MP Bullet Camera, West outdoor exit of building.

3.25 Inside Cameras

3.25.1 Camera two, 4 MP Dome Camera, North exit hallway

3.25.2 Camera three, 4 MP Dome Camera, South exit hall wall.

3.25.3 Camera four, 4 MP Dome Camera, NE open area.

3.25.4 Camera five, 4 MP Dome Camera, NW corner hallway.

3.25.5 Camera six, 4 MP Dome Camera, above West stairwell entrance.

3.25.6 Camera seven, 4 MP Dome Camera, inside East hallway.

3.25.7 Camera eight, 4 MP, Dome Camera, inside NW hallway foyer.

3.25.8 Camera nine, 4 MP Dome Camera, inside West hallway.

3.26 The cameras shall be located in the following areas in BLDG 10806.

3.27 BLDG 10806, First Floor Outside Cameras

3.27.1 Camera One, 4 MP Bullet Camera, NW corner of building.

3.27.2 Camera Two, 4 MP Bullet Camera, NW corner of building.

3.27.3 Camera Three, 4 MP Bullet Camera, North wall of building.

3.27.4 Camera Five, 4 MP Bullet Camera. North outside exit door.

3.27.5 Camera Six, 4 MP Bullet Camera. North outer wall.

3.27.6 Camera Seven 4 MP Bullet Camera, NE corner of building.

3.27.7 Camera Eight, 4 MP Bullet Camera, NE corner of building.

3.27.8 Camera Nine, 4 MP Bullet Camera, SE corner center of building.

3.27.9 Camera Ten, 4 MP Bullet Camera, SE corner center of building.

3.27.10 Camera 11, 4 MP Bullet Camera, East corner center of building.

3.27.11 Camera 12, 4 MP Bullet Camera, SE corner center of building.

3.27.12 Camera 17, 4 MP Bullet Camera, SW inner corner center of building.

3.27.13 Camera 18, 4 MP Bullet Camera, SW inner corner center of building.

3.27.14 Camera 20, 4 MP Bullet Camera, South indent of building next to entrance.

3.27.15 Camera 21, 4 MP Bullet Camera. SE corner indent of building next to entrance.

3.27.16 Camera 22, 4 MP Bullet Camera. SW corner indent of building next to entrance.

3.27.17 Camera 23, 4 MP Bullet Camera, SW corner of building.

Security Camera System

3.27.18 Camera 24, 4 MP Bullet Camera, SW corner of building.

3.27.19 Camera 25, 4 MP Bullet Camera. West outer wall.

3.27.20 Camera 27, 4 MP Bullet Camera. West stairwell, outside exit.

3.27.21 Camera 28, 4 MP Bullet Camera. West outer wall.

3.27.22 Camera 29, 4 MP Bullet Camera. West outer wall.

3.27.23 Camera 30, 4 MP Bullet Camera. NW outer corner of building.

3.27.24 Camera 31, 4 MP Bullet Camera. NE outer corner of building.

3.28 BLDG 10806, Inside Cameras

3.28.1 Camera four, 4 MP Dome Camera, North exit hallway

3.28.2 Camera 15, 4 MP Dome Camera, South exit hall wall.

3.28.3 Camera 16, 4 MP Dome Camera, North open foyer.

3.28.4 Camera 19, 4 MP Dome Camera. East hallway exit.

3.28.5 Camera 26, 4 MP Dome Camera, West hallway exit.

3.28.6 Camera 14, 4 MP Dome Camera, SW open foyer.

3.28.7 Camera 13, 4 MP Dome Camera, entrance to stairways.

3.28.8 Camera 32, 4 MP Dome Camera, NE corner of office.

3.29 BLDG 10806, 2nd Floor Outside Cameras

3.29.1 Camera One, 4 MP Bullet Camera, North outdoor exit of building.

3.29.2 Camera 11, 4 MP Bullet Camera, West outdoor exit of building.

3.30 BLDG 10806, Inside Cameras

3.30.1 Camera two, 4 MP Dome Camera, North exit hallway.

3.30.2 Camera three, 4 MP Dome Camera, South exit hallway.

3.30.3 Camera four, 4 MP Dome Camera, NE ceiling laundry room.

3.30.4 Camera five, 4 MP Dome Camera. East ceiling laundry room.

3.30.5 Camera six, 4 MP Dome Camera. South ceiling facing laundry room entrance.

3.30.6 Camera seven, 4 MP Dome Camera, above West stairwell entrance.

3.30.7 Camera eight, 4 MP Dome Camera, East hallway

3.30.8 Camera nine, 4 MP Dome Camera, inside NW hallway foyer.

3.30.9 Camera ten, 4 MP Dome Camera, West hallway.

3.31 BLDG 10806, 3rd Floor Outside Cameras

3.31.1 Camera One, 4 MP Bullet Camera, North outdoor exit of building.

3.31.2 Camera Nine, 4 MP Bullet Camera, West outdoor exit of building.

3.32 BLDG 10806, Inside Cameras

3.32.1 Camera two, 4 MP Dome Camera, North exit hallway

3.32.2 Camera three, 4 MP Dome Camera, South exit hall wall.

Security Camera System

3.32.3 Camera four, 4 MP Dome Camera, NW ceiling open hallway area.

3.32.4 Camera five, 4 MP Dome Camera. East exit hallway.

3.32.5 Camera seven, 4 MP Dome Camera, SW stairwell exit.

3.32.6 Camera eight, 4 MP Dome Camera, West hallway exit.

3.32.7 Camera six, 4 MP Dome Camera, South foyer hallway.

3.32.8 Camera ten, 4 MP Dome Camera, NE corner of office.

4. General Information for Building 10504

The work required includes the design, delivery and full installation of the security monitoring system. The contractor shall provide, install and configure all necessary equipment for a security monitoring system. The layout provided by the Government provides a tentative conceptual design but can be altered pending circumstances.

All cameras shall be of sufficient quality to be able to see in low/no light. The outside cameras shall be protected in an all-weather, wind, rain, and hail protective shell. The system shall include an NVR recorder located in Rm 125, with the capability of recording 24/7/365 days a year, and shall store video feeds for no less than 30 days with a capability to store to an external hard drive or DVD/CD.

The LED monitors shall be located in the Admin Office, Rm 105 mounted against the west wall where the previous monitors were located. The cameras shall have a clear view at night, and zoom in options.

The contractor shall provide and install all necessary conduit, cabling, boxes, conversion, equipment, and programming labor required for a complete and fully operational system.

Cabling shall be installed neatly, out of view when possible, and not produce any avoidable safety hazards. Any and all installation not limited to the cameras shall be mounted securely.

The audio video control system requires display/playback capabilities. In addition, upon completion, vendor shall provide training and instructions of proper use of system, backup, and camera usage. The contractor shall remove the previous cameras. The cameras shall be turned into the squadron. The system shall consist of the following; however, it is not limited to the following based on the contractor proposed design.

5. The cameras for bldg. 10504 shall be located in the following areas:

Item needed and quantity (as applicable):

123 (EA) ACC 7 Enterprise Camera License

2 (EA) Premium 64TB 2U Rack Mnt, Network Video Recorder

108 (EA) 2.0 MP Indoor Dome Camera

15 (EA) 2.0 Outdoor Megapixel (1080p) WDR Day/Night Dome Camera

15 (EA) Corner Mount Adapter

4 (EA) 42.5'' Premium Wide LED Monitor

2 (EA) UPS 3000

12 (EA) UPS XL 48V Battery Pack

15 (EA) Outdoor Camera Installation Kit

108 (EA) Indoor Camera Installation Kit

5.1 Outside of Building 10504

5.1.1 South End of Building level with the 2nd floor.

5.1.2 1 (EA) Southwest Outer Corner C38

5.1.3 1 (EA) South Center C18

5.1.4 1 (EA) Southeast Outer Corner C39

5.1.5 West End of Building level with the 2nd floor.

5.1.6 1 (EA) Southwest Outer Corner C41

5.1.7 1 (EA) West Center C21

5.1.8 1 (EA) Northwest Outer Corner C40

5.1.9 North Front of Building level with the 1st floor.

5.1.10 1 (EA) Northwest Corner C32

5.1.11 1 (EA) North Left Entrance C10

5.1.12 1 (EA) South Right Entrance C11

5.1.13 1 (EA) Northeast Corner C33

5.1.14 East End of Building level with the 2nd floor.

5.1.15 1 (EA) Northeast Corner C36

5.1.16 1 (EA) Southeast Corner C37

5.1.17 East Outside internal corner of building level with the 1st floor.

5.1.18 1 (EA) Southeast Corner C34

5.1.19 West Outside internal corner of building level with the 1st floor.

5.1.20 1 (EA) Southwest Corner near air condition units C12

5.1.21 1 (EA) Southwest Corner internal wall C35

5.2 1st Floor (inside) Building 10504

5.2.1 South Hall cameras shall be located outside the following rooms.

5.2.2 1 (EA) C68

5.2.3 1 (EA) C69

5.2.4 1 (EA) C16

5.2.5 1 (EA) C17

5.2.6 1 (EA) C70

5.2.7 West Hall cameras shall be located outside the following rooms.

5.2.8 1 (EA) C73

5.2.9 1 (EA) C72

5.2.10 1 (EA) C19

5.2.11 1 (EA) C20

5.2.12 1 (EA) C71

5.2.13 East Hall cameras shall be located outside the following rooms.

5.2.14 1 (EA) C65

5.2.15 1 (EA) C68

Security Camera System

5.2.16 1 (EA) C13

5.2.17 1 (EA) C14

5.2.18 1 (EA) C67

5.2.19 Open Area cameras shall be located outside the following rooms.

5.2.20 1 (EA) Rm 138 Classroom C8

5.2.21 2 (EA) Laundry Rm C7, C9

5.2.22 1 (EA) Inside Stairwell C6

5.2.23 1 (EA) Outside Stairwell Entrance C63

5.2.24 1 (EA) Outside Rm 123 C64

5.2.25 3 (EA) Open area above CQ desk in center of building C3, C5, C2,

5.2.26 1 (EA) Outside Rm 125 COMM Rm C4

5.2.27 1 (EA) Outside Admin Office Rm 105 C54

5.2.28 1 (EA) Outside West student hallway C62

5.3 2nd Floor (inside) Building 10504

5.3.1 South Hall cameras shall be located outside the following rooms.

5.3.2 1 (EA) C85

5.3.3 1 (EA) C86

5.3.4 1 (EA) C28

5.3.5 1 (EA) C29

5.3.6 1 (EA) C8

5.3.7 West Hall cameras shall be located outside the following rooms.

5.3.8 1 (EA) C90

5.3.9 1 (EA) C89

5.3.10 1 (EA) C30

5.3.11 1 (EA) C31

5.3.12 1 (EA) C88

5.3.13 East Hall cameras shall be located outside the following rooms.

5.3.14 1 (EA) C82

5.3.15 1 (EA) C83

5.3.16 1 (EA) C26

5.3.17 1 (EA) C27

5.3.18 1 (EA) C84

5.3.19 Open Area cameras shall be located outside the following rooms.

5.3.20 3 (EA) Open Hallway outside Laundry Rm C78, C81, C80

5.3.21 2 (EA) Laundry Rm 206 C25, C24

5.3.22 1 (EA) Inside Stairwell Entrance C79

5.3.23 2 (EA) Conference Rm 202 C22, C23

5.3.24 1 (EA) Outside Conference Rm 202 C77

5.3.25 2 (EA) Open hallway area C74, C76

5.3.26 1 (EA) Outside hallway going to East dorm rooms C75

5.4 3rd Floor (inside) Building 10504

Security Camera System

5.4.1 South Hall cameras shall be located outside the following rooms.

5.4.2 1 (EA) C102

5.4.3 1 (EA) C103

5.4.4 1 (EA) C48

5.4.5 1 (EA) C49

5.4.6 1 (EA) C104

5.4.7 West Hall cameras shall be located outside the following rooms.

5.4.8 1 (EA) C107

5.4.9 1 (EA) C108

5.4.10 1 (EA) C50

5.4.11 1 (EA) C51

5.4.12 1 (EA) C105

5.4.13 East Hall cameras shall be located outside the following rooms.

5.4.14 1 (EA) C99

5.4.15 1 (EA) C109

5.4.16 1 (EA) C46

5.4.17 1 (EA) C47

5.4.18 1 (EA) C48

5.4.19 Open Area cameras shall be located outside the following rooms.

5.4.20 2 (EA) Laundry Rm C45, C44

5.4.21 1 (EA) Open Hallway outside Laundry C98

5.4.22 1 (EA) Inside Stairwell Entrance C96

5.4.23 1 (EA) Outside COMM Rm C93

5.4.24 2 (EA) Conference C42, C43

5.4.25 1 (EA) Outside CE room C91

5.4.26 4 (EA) Open area outside Conference Rm C92, C87, C94, C97

5.5 4th Floor (inside) Building 10504

5.5.1 South Hall cameras shall be located outside the following rooms.

5.5.2 1 (EA) C119

5.5.3 1 (EA) C120

5.5.4 1 (EA) C58

5.5.5 1 (EA) C59

5.5.6 1 (EA) C121

5.5.7 West Hall cameras shall be located outside the following rooms.

5.5.8 1 (EA) C124

5.5.9 1 (EA) C123

5.5.10 1 (EA) C57

5.5.11 1 (EA) C56

5.5.12 1 (EA) C122

5.5.13 East Hall cameras shall be located outside the following rooms.

5.5.14 1 (EA) C116

5.5.15 1 (EA) C117

5.5.16 1 (EA) C61

5.5.17 1 (EA) C60

5.5.18 1 (EA) C118

Security Camera System

5.5.19 Open Area cameras shall be located outside the following rooms.

5.5.20 2 (EA) Laundry Rm C55, C54

5.5.21 2 (EA) Outside Rm 404 COMM Rm C114, C115

5.5.22 1 (EA) Inside Stairwell Entrance C113

5.5.23 1 (EA) Inside Rm 402 Day Rm C52, C53

5.5.24 1 (EA) Rm Day Rm 404 C112

5.5.25 3 (EA) Open area outside Conference Rm 408 C108, C110, C111

5.5.26 1 (EA) Outside RM 407 C109

5.6 (123 EA) ACC 7 Enterprise Camera License shall have the following specifications, Building 10504

Manufacturer: Avigilon

Part Number: ACC7-ENT

5.6.1 Focus of Attention Interface

5.6.2 Facial Recognition Technology

5.6.3 Appearance Search Technology

5.6.4 Self-Learning Video Analytics

5.6.5 Detect Unusual Activity

5.6.6 Detect Unusual Motion Detection

5.6.7 Maintain Video Archive

5.7 (2 EA) Premium 64TB 2U Rack Mnt, Network Video Recorder shall have the following specifications. Building 10504

Manufacturer: Avigilon

Part Number: NVR4X-PRM-64TB-NA

5.7.1 Recording Mode Real Time

5.7.2 Software solution

5.7.3 Hardware solution

5.7.4 Inbuilt multiplexer

5.7.5 Simultaneous Live

5.7.6 Recording, Playback

5.7.7 Recording system Hard Disk Drive (HDD

5.7.8 Storage capacity 64 Terabyte (TB)

5.7.9 Resolution 7K (30 MP)

5.7.10 Expandable to multi network video recorder (NVR)

5.7.11 Multiple NVR support

5.7.12 Voltage 100 ~ 240 V Alternate Current (AC)

5.7.13 Power consumption (W) 429 ~ 750

5.7.14 Weight 102 lbs.

5.7.15 Operating temperature 50 ~ 95 F

5.7.16 Operating humidity 10 ~ 80

5.7.17 Configured for and preloaded with video management software (VMS)

5.7.18 Simultaneous recording, playback and live streaming

5.7.19 Hot-swappable components

5.8 (108 EA) 2.0 MP Indoor Dome Camera shall have the following specifications Building

10504

Manufacturer: Avigilon

Part Number: 2.0C-H5A-D1-IR

5.8.1 Chip Inch Size 1/3

5.8.2 Color Type Color / Monochrome

5.8.3 Resolution TV LINES 2 Megapixel (MP)

5.8.4 Indoor/Outdoor capabilities

5.8.5 Mount Type Surface

5.8.6 Electrical Specifications Voltage: 12 V Direct Current (DC) / 24 V AC /

5.8.7 Power Over Ethernet (PoE)

5.8.8 Power Consumption: 13 W

5.8.9 Focal length 3.3 ~ 9 mm

5.8.10 Compression H.264 High-Definition System Management (HDSM) Smart Codec

5.8.11 Back Light Compensation

5.8.12 White Balance

5.8.13 Electronic Shutter range Automatic, Manual (1/7 to 1/8196 sec)

5.8.14 Network Properties Interface: 100BASE-TX, RJ45 Connector, CAT6e Cabling

5.8.15 Network Protocols: Internet Protocol (IP) v6, IPv4, Web Interface Connections

5.8.16 Image Frame Rate: 25 frames per second (fps) /30

5.8.17 Dimensions mm: 163 x 163 x 118

5.8.18 Weight 2.18 Lbs.

5.8.19 Operating Temp (-40 ~ +149 F)

5.8.20 Operating Humidity %: 0 ~ 95

5.8.21 Protection: IP66, IP67, IK10

5.9 (15 EA) 2.0 Outdoor Megapixel (1080p) WDR Day/Night Dome Camera shall have the following specifications Building 10504

Manufacturer: Avigilon

Part Number: 2.0C-H4PTZ-DP30

5.9.1 Image Sensor Wide Dynamic Range 1/2.8” progressive scan

5.9.2 Active Pixels 1280 (H) × 720 (V) 1920 (H) × 1080 (V)

5.9.3 Imaging Area 4.8 mm (H) × 2.7 mm (V); 0.189” (H) × 0.106” (V)

5.9.4 Dynamic Range 120+ decibel (dB)

5.9.5 Image Rate Up to 60 fps

5.9.6 3D Noise Reduction Filter (NRF)

5.9.7 Lens 4.3 to 129 mm autofocus

5.9.8 Angle of View 2.3° - 63.7°

5.9.9 Optical Zoom 30x

Security Camera System

5.9.10 Video Compression H.264 (MPEG-4 Part 10/Advance Video Coding)

5.9.11 Electronic Shutter Control Automatic, Manual (1/1 to 1/10,000 sec)

5.9.12 Iris Control Automatic, Manual

5.9.13 Day/Night Control Automatic, Manual

5.9.14 Flicker Control 50 Hz, 60 Hz

5.9.15 White Balance Automatic, Manual

5.9.16 Backlight Compensation Manual

5.9.17 Privacy Zones Up to 64 zones, 3D privacy mask supported

5.9.18 500 named presets

5.9.19 Electronic Image Stabilization On/Off

5.9.20 Digital Defog Adjustable/Off

5.9.21 Network 100BASE-TX

5.9.22 Cabling Type CAT6 and 5e

5.9.23 Security Password protection

5.9.24 Multiple Secured Protocols

5.9.25 Multiple Streaming Protocols

5.9.26 Audio Input/ Output Line level input and output

5.9.27 External I/O Terminals Alarm In, Alarm Out

5.9.28 Weight 8.6 lbs.

5.9.29 Dome Bubble Nylon

5.9.30 Body Plastic Aluminum

5.9.31 Finish: Powder coat

5.9.32 Body: Aluminum, stainless steel, silicone rubber

5.9.33 Female 1-1/2 camera mount

5.9.34 3/4“National Pipe Tapered (NTP) conduit entry

5.10 (15 EA) Corner Mount Adapter shall have the following specifications Building 10504

Part Number: CM-MT-WALL 1

5.10.1 Type of Mount: Dome Mounts

5.10.2 Mount Position: Pendant, Wall

5.10.3 Mount Material: Aluminum

5.10.4 Stainless steel

5.10.5 Silicone rubber

5.10.6 Finish: Powder coat

5.10.7 Female 1-1/2 camera mount

5.10.8 3/4“conduit

5.11 (4 EA) 42.5'' Premium Wide LED Monitor shall have the following specifications

Building 10504

Manufacturer: Orion

Part Number: 43REDP

Security Camera System

5.11.1 Screen Size 42.51"

5.11.2 Backlight LED

5.11.3 Maximum Resolution 1920 x 1080 at 60 Hz

5.11.4 Pixel Pitch 0.4902 x 0.4902 mm

5.11.5 Brightness 450 cd/m²

5.11.6 Contrast Ratio 1100:1

5.11.7 Aspect Ratio 16:9

5.11.8 Viewing Angle (H/V) 178/178°

5.11.9 Display Color 16.7 million (8-bit)

5.11.10 Video System NTSC, PAL

5.11.11 Video In/Out 2/2 Bayonet Neil Concelman (BNC)

5.11.12 S-Video In/Out 1/1

5.11.13 DVI-D In 1, HDMI In 2

5.11.14 Video Graphic Array (15-pin D-sub)

5.11.15 Audio In (L/R) 2 (RCA)

5.11.16 PC Stereo In 1

5.11.17 Transmitter Remote Control

5.11.18 Audio Built-In Speakers 2 x 10 W

5.11.19 Multi-Display Function, Picture in Picture.

5.11.20 Auto Power Recover

5.11.21 Noise Reduction

5.11.22 Light-Emitting Diode Protection Glass

5.11.23 Auto Pixel Shift

5.11.24 Auto Source Sequencing

5.11.25 Dimensions (W x H x D) 38.16 x 24.62 x 9.44"

5.11.26 Weight 48.06 lb.

5.12 (2 EA) (UPS) 3000 shall have the following specifications Building 10504

Manufacturer: APC

Part Number: SUA3000RM2U

5.12.1 Max Configurable Power (Watts) 2.7kWatts / 2.88kVA

5.12.2 Output Voltage Distortion Less than 5 %

5.12.3 Topology Line interactive

5.12.4 Waveform type Sine wave

5.12.5 Transfer Time 4 milliseconds typical: 8 m maximum

5.12.6 Input frequency 50/60 Hz +/- 3 Hz Auto-sensing

5.12.7 Number of Power Cords 1

5.12.8 Battery type Lead-acid battery

5.12.9 Typical recharge time 3hour(s)

5.12.10 Expected Battery Life (years) 3 - 5

5.12.11 Battery Charge Power 188 Watts

5.12.12 RJ-45 Serial, Smart-Slot, Universal Serial Bus

5.12.13 Control panel Light Emitting Diode status display

5.12.14 Control console

Security Camera System

5.12.15 Audible Alarm

5.12.16 Alarm when on battery

5.12.17 Distinctive low battery alarm

5.12.18 Overload continuous tone alarm

5.12.19 Surge energy rating 459Joules

5.12.20 Physical Maximum Height 3.4inches

5.12.21 Maximum Width 18.9inches

5.12.22 Maximum Depth 26.9inches

5.12.23 Net Weight 97.62lbs

5.13 (12 EA) UPS XL 48V Battery Pack shall have the following specifications Building

Manufacturer: APC

Part Number: SUA48XLBD

5.13.1 Input Number of Power Cords 1

5.13.2 Battery type Lead-acid battery

5.13.3 Replacement Battery Charge: Quantity 2

5.13.4 Battery Charge Power 163.2k Watts

5.13.5 Maximum Height 17.48 inches

5.13.6 Maximum Width 8.7 inches

5.13.7 Maximum Depth 19.49 inches

5.13.8 Net Weight 146.3 lbs

5.14 (15 EA) Outdoor Camera Connection Kit shall have the following specifications Building

Manufacturer: AIS

Part Number: CKO-CAT6

5.14.1 Data Transfer Speed: 10 Gbps

5.14.2 Connector Type: RJ45 cat7

5.14.3 Conductors: 26 American Wire Gauge (AWG)

5.14.4 Support bandwidth up to 350Mhz

5.14.5 Support speed up to 10 Gigabit Per Second

5.14.6 26 AWG /PAIRS, Outside Diameter:6.3 mm

5.14.7 Gold Plated RJ45 connectors

5.14.8 4 Pair Unshielded Twisted Pair copper strands

5.14.9 Strange heavy-duty cable, flexible polyvinyl chloride jacket

5.15 (108 EA) Indoor Camera Connection Kit shall have the following specifications Building

Manufacturer: AIS

Part Number: CKI-CAT6

5.15.1 1 Gigabits (Gbps) data transfer and 250MHz bandwidth

5.15.2 Unshielded twisted pair (UTP) patch cable

5.15.3 Bare copper wire and gold-plated contacts

6. GENERAL INFORMATION

All Outside Plant (OSP) and Inside Plant (ISP) cabling projects installed on Lackland AFB, Medina Annex, or Camp Bullis as part of any MILCON, SABER, or other project shall meet commercial industry and Telecommunications Systems Cabling Standards. Please reference

13A Standards and UFC 3-580-1 Telecommunication Interior Infrastructure Planning and Design with Change.

7. WORK HOURS AND SPECIAL CONDITIONS

Work hours shall begin at 7:30 p.m. through 4:30 p.m., Monday through Friday, exclusive of

Federal holidays. At the option of the Government and with approval of the Contracting Officer, work may be permitted on Federal holidays, weekends, or after 4:30 p.m. at no additional cost to the Government.

New Year's Day

Martin Luther King Jr's

Birthday

President’s Day

Memorial Day

Juneteenth

Independence Day

Labor Day

Columbus Day

Veterans' Day

Thanksgiving Day

Christmas Day

8. BASE FIRE REGULATIONS

The contractor shall comply with all JBSA-Lackland AFB Post Fire Regulations. Contractor shall have all permits needed to perform job.

9. SITE MAINTENANCE AND CLEANUP

Site Maintenance: The contractor shall maintain work areas in a neat, clean, and safe condition.

The contractor shall be responsible for providing, installing, and the removal of any temporary signage, barriers, barricade tape, etc. which may be required to control pedestrian in the work area. The contractor shall collect all trash, debris, refuse, garbage, etc., which is. The aforementioned materials shall be removed from the site by appropriate means daily. Contractor

Security Camera System shall not work or store materials in a manner that would hinder or otherwise block pedestrian circulation to exit corridors and exit doors in the event of an emergency or fire. Storage of materials shall be coordinated with the customer. The contractor shall be responsible for freight, unpacking, delivery and inside installation.

10. ENERGY CONSERVATION

The contractor shall use good judgment in the conservation of Government utilities. The contractor shall adhere to and enforce prevailing energy conservation practices.

11. CONTRACT MANAGEMENT

No changes in or deviation from the scope of service shall be affected without a modification executed by the Contracting Officer authorizing such changes.

12. RECORDS MANAGEMENT

"The Contractor shall manage all data created for Government use or legally controlled by the

Government, in support of the functional activity or required by AF publication, IAW with the

AF Records Management procedures in Air Force Instruction (AFI) 33-322, Air Force Manual

(AFMAN) 33-363 and Air Force Instruction (AFI) 33-364 (or their subsequent replacements)".

13. INSPECTION AND ACCEPTANCE

Mr. Don Walborn, 37 TRSS/671-2164 will conduct the final inspection with the Contractor and the Contracting Office to determine whether the project can be accepted or corrections required prior to acceptance.