Attachment 2 - DRAFT Technical Specification_IC2PL2529.pdf

RFI 70Z04424IC2PL2529

Attachment 2, Technical Specification v1.1

LAST UPDATED: 04/16/2025 PAGE 1/8

TECHNICAL SPECIFICATION FOR

Global Navigation Satellite System (GNSS) Recapitalization

1.0 GENERAL

1.1 BACKGROUND

Global Navigation Satellite System (GNSS) receivers are utilized to provide accurate and secure Position, Navigation, and Timing (PNT) service to United States Coast Guard (USCG) cutters and boats. The USCG requires a new GNSS receiver and antenna set to support electronic navigation at sea and Aids to Navigation (AtoN) requirements. The existing GNSS receivers are unable to meet new PNT requirements and the hardware is obsolete and no longer supportable. A complete recapitalization is necessary to ensure the hardware is available to meet requirements. The GNSS recapitalization project seeks to replace the outdated equipment with newer, supportable components to sustain and improve PNT service for the USCG fleet.

1.2 OBJECTIVE

The objective of this specification is to identify and procure marine-grade, GNSS receivers and antennas for use on-board Coast Guard cutters and boats. This effort standardizes the GNSS hardware utilized by the USCG fleet. This specification identifies the requirements of the next generation GNSS receiver and antenna set that will replace legacy hardware.

1.3 APPLICABLE DOCUMENTS

1.3.1 Compliance Documents

The following documents provide specifications, standards, or guidelines that must be complied with in order to meet the requirements of this contract:

IEC 60945 Ed. 4.0 b Cor.1:2008

IEC 61108-1 Ed 2.0 b:2003

IACS E10 Test Specification for Type Approval

International Electrotechnical Commission (2013). IEC 60529 - Degrees of protection provided by enclosures (IP Code). International standard (2.2 ed.). p. 21. ISBN 9782832210864. OCLC 864643678

2.0 SPECIFICATIONS

The requirements contained herein are the Threshold (minimum) requirement. In addition, there are requirements identified as “Objective”, which is a preferred system capability, but not a threshold/minimum requirement.

LAST UPDATED: 04/16/2025 PAGE 2/8

2.1 GENERAL:

a. Must comply with IEC 60945 (Threshold)

b. Must comply with IEC 61108-1 (Threshold)

2.2 SIZE, WEIGHT, AND POWER (SWAP)

a. Size:

I. Maximum: 300 cubic inches (Threshold)

b. Operating Voltage:

I. 10 - 30 VDC (Threshold)

II. Dual input voltage source capable VDC OR 120V AC (Objective) III. Internal battery backup source (Objective)

2.3 ENVIRONMENT

a. Shock: (Threshold) I. 75 g (non-operating) II. 40 g (Operating)

b. Drop:

I. Survive a 1m drop on hard surface (Threshold) II. Survive a drop greater than 1m on hard surface (Objective)

c. Temperature (Operating and Storage):

I. – 40 degrees F to +140 degrees F (Threshold)

d. Waterproof rating:

I. IP rating of 67 (Threshold) II. IP rating of 68 or greater (Objective)

2.4 ELECTROMAGNETIC INTERFERENCE (EMI) AND ELECTROMAGNETIC

COMPATIBILITY (EMC)

a. Must comply to IEC 60945 and RTCM 13700.0 Standards (Threshold)

2.5 DETERMINATION OF POSITION

a. Accuracy:

I. Horizontal position variation less than 2m via WAAS (Threshold)

2.6 SECURITY

a. Wi-Fi & Bluetooth capabilities must be configurable (enabled/disabled) (Threshold)

b. Wi-Fi & Bluetooth capabilities must allow user configurable password protected

(Objective)

c. Web user interface must be password protect configuration access (Objective)

2.7 INTERFERENCE SUPPRESSION (ANTI-JAM)

a. Receiver must have the ability to detect jam and spoof threats. (Objective)

b. Receiver must notify user via alarm when jam and/or spoof threat is detected on both primary and secondary system(s) (Objective)

LAST UPDATED: 04/16/2025 PAGE 3/8

c. Anti-Jam antenna capable (Objective)

2.8 OPERATION

a. Automatic selection of satellite-transmitted signals for position determination (Threshold)

b. Receiver must acquire signal for first fix within 2 minutes from cold start (Threshold)

c. Receiver must reacquire signal for first fix within 30 seconds from hot start (Threshold)

d. Receiver must generate and output to a display and digital interface a new position no less than once per second (Threshold)

e. Receiver must provide alerts when jamming or spoofing is detected (Objective)

2.9 ANTENNA SPECIFICATIONS

a. Mountable on a standard 1 inch 14 NPT antenna mount (Objective)

b. Controlled Reception Pattern Antenna (CRPA) capable (Objective)

2.10 FEATURES

a. Provides Satellite Compass Heading: (Threshold) I. 0.75° RMS or greater accuracy (Threshold)

II. 0.25° RMS or greater accuracy (Objective)

b. Selectable Constellations: (Threshold)

I. GPS (L1 & L2): (Threshold) II. GPS (L5) (Objective)

III. Galileo: (Threshold) IV. GLONASS: (Threshold) V. BeiDou: (Threshold)

VI. QZSS: (Threshold) VII. NavIC: (Objective)

c. Selectable Satellite Based Augmentation System (SBAS): (Threshold) I. ASAL (Algeria) - (Threshold)

II. ASECNA (Africa/Indian Ocean) - (Threshold) III. BDSBAS (China) - (Threshold) IV. EGNOS (Europe) - (Threshold) V. GAGAN (India) - (Objective)

VI. KAAS (Korea) - (Threshold) VII. MSAS (Japan) - (Threshold)

VIII. SDCM (Russia) - (Threshold) IX. SPAN (Australia / New Zealand) - (Threshold) X. QZSS (Japan) - (Threshold)

2.11 DATA (I/O)

a. NMEA data standards:

I. NMEA 0183 (4.30 or greater) (Threshold)

II. NMEA 2000 (3.00 or greater) (Objective)

LAST UPDATED: 04/16/2025 PAGE 4/8

III. NMEA OneNet (1.00 or greater) (Objective)

b. Selectable (ON/OFF) output sentences (Threshold):

I. GGA

II. GNS

III. GLL

IV. HDT

V. VTG

VI. GST

VII. GRS

VIII. GSA

IX. DTM

X. ZDA

XI. RTE

XII. WPL

XIII. ROT

c. Selectable (ON/OFF) output sentences (Objective):

I. THS

II. RMC

III. GBS

IV. GDC

V. GFA

VI. GIR

VII. GRP

VIII. GGC

IX. GMP

d. Provide Network data interface via physical connection suitable for TCP/IP interface (Threshold)

I. Receiver must have the capability to be assigned an Internet Protocol Version 4 (IPv4) address and communicate over IPv4 schema. (Threshold)

II. Receiver must have the capability to be assigned an Internet Protocol Version 6 (IPv6) address and communicate over IPv6 schema. (Threshold)

III. Receiver TCP/IP interface must be configurable, allowing the operator to choose between an IPv4 or IPv6 schema for TCP/IP communication. (Threshold)

e. Selectable output frequency 1 – 10 Hz (Threshold):

I. GGA

II. GNS

III. GLL

IV. HDT

V. VTG

VI. GST

VII. GRS

VIII. GSA

LAST UPDATED: 04/16/2025 PAGE 5/8

IX. DTM

X. ZDA

XI. RTE

XII. WPL

XIII. ROT

f. Selectable output frequency 1 – 10 Hz (Objective):

I. THS

II. RMC

III. GBS

IV. GDC

V. GFA

VI. GIR

VII. GRP

VIII. GGC

IX. GMP

g. Selectable baud rates: (Threshold) I. 4800 (Threshold)

II. 9600 (Threshold) III. 19200 (Threshold) IV. 38400 (Threshold) V. 57600 (Objective)

VI. 115200 (Objective) VII. 230400 (Objective)

h. Provide two serial output ports (Threshold) I. Each serial outport port must be configurable for RS-422/232/485 (Threshold)

II. Provide three or more serial output ports (Objective)

2.12 RECEIVER CONFIGURATION MANAGEMENT

a. Configurable via a configuration file (Threshold) I. Configuration file must be exportable/importable (Threshold)

b. Configurable via web browser interface (Objective)

c. All configuration options available via the receiver interface directly (Objective)

2.13 LOGISTICS

a. Supportability I. For any software products, the contractor must provide all manufacturer software updates, and patches to correct defects, for the life of the product [i.e., until the “End of Life” (EoL) or “End of Support” (EoS)]. Software updates and patches must be made available to the government for all products procured under this Contract and replaced when End of Support (EoS) is reached. (Threshold)

II. For any hardware products (utilizing firmware), the contractor must provide all manufacturer firmware updates to correct defects, for the life of the product [i.e., LAST UPDATED: 04/16/2025 PAGE 6/8 until the “End of Life” (EoL) or “End of Support” (EoS)]. Firmware updates must be made available to the government for all products procured under this Contract and replaced when End of Support (EoS) is reached. (Threshold)

III. Contractor must provide notification timelines for software and/or firmware updates, product end of life, and reparability support. (Threshold)

b. Configuration Management I. Exact model number and capability of components must be available for order for the entirety of the contract period of performance (Threshold)

c. Reliability – Mean Time Between Failure (MTBF)

I. Each item must have a reliability of 16,000 hours MTBF (Threshold) II. Each item must have a reliability of 18,000 hours MTBF (Objective)

2.14 DELIVERY TERMS

a. The product must be delivered to the Government within 90 calendar days of delivery order award. (Threshold)

b. The product must be delivered to the Government within 45 calendar days of delivery order award. (Objective)

3.0 WARRANTY

The contractor must provide, at a minimum, a one-year standard commercial warranty, which commences on date of installation on a USCG asset. Product warranties must include a product return policy. Any Original Equipment Manufacturer (OEM) warranties associated with products delivered under this contract/order must be available directly to the USCG.

4.0 SECTION 508 COMPLIANCE

4.1. Section 508 Requirements (include in the SOW, PWS, or SOO) Section 508 of the Rehabilitation Act (classified to 29 U.S.C. § 794d) requires that when Federal agencies develop, procure, maintain, or use information and communications technology (ICT), it shall be accessible to people with disabilities. Federal employees and members of the public with disabilities must be afforded access to and use of information and data comparable to that of Federal employees and members of the public without disabilities.

All products, platforms and services delivered as part of this work statement that, by definition, are deemed ICT shall conform to the revised regulatory implementation of Section 508 Standards, which are located at 36 C.F.R. § 1194.1 & Appendixes A, C & D, and available at https://www.ecfr.gov/cgi-bin/text-idx?SID=e1c6735e25593339a9db63534259d8ec&mc=true&node=pt36.3.1194&rgn=div5. In the revised regulation, ICT replaced the term electronic and information technology (EIT) used in the original 508 standards. ICT includes IT and other equipment.

Exceptions for this work statement have been determined by DHS and only the exceptions described herein may be applied. Any request for additional exceptions shall be sent to the Contracting Officer and a determination will be made according to DHS Directive 139-05, Office https://uscode.house.gov/view.xhtml?req=(title:29%20section:794d%20edition:prelim)%20OR%20(granuleid:USC-prelim-title29-section794d)&f=treesort&edition=prelim&num=0&jumpTo=true https://www.ecfr.gov/cgi-bin/text-idx?SID=e1c6735e25593339a9db63534259d8ec&mc=true&node=pt36.3.1194&rgn=div5 https://www.ecfr.gov/cgi-bin/text-idx?SID=e1c6735e25593339a9db63534259d8ec&mc=true&node=pt36.3.1194&rgn=div5

LAST UPDATED: 04/16/2025 PAGE 7/8

of Accessible Systems and Technology, dated November 12, 2018 and DHS Instruction 139-05- 001, Managing the Accessible Systems and Technology Program, dated November 20, 2018, or any successor publication.

4.2 Section 508 Requirements for Technology Products (include in the SOW, PWS, or

SOO)

Section 508 applicability to Information and Communications Technology (ICT): C5ISC GNSS Receiver Applicable Exception: ICT Functions Located in Maintenance and Monitoring Spaces Authorization #: EXC0001533

5.0 DELIVERABLES

The contractor must reference the applicable CDRL for all applicable deliverable requirements, submission due dates, and distribution.

CDRL

NUMBER DELIVERABLE NAME

TECHNICAL

SPECIFICATION

SECTION

A001 Standard commercial Operation, Maintenance, Service and User manuals 5.0

6.0 DHS GEOSPATIAL INFORMATION SYSTEM COMPLIANCE

All implementations including geospatial data, information, and services shall comply with the policies and requirements set forth in the DHS Geospatial Information Infrastructure (Gil), including (but not limited to) the following:

a. All data built to the GII whether adopted or developed, shall be submitted to the government for review and insertion into the DHS Data Reference Model.

b. All software built to the GII, whether adopted or developed, shall be submitted to the government for review and insertion into the DHS Technical Reference Model.

7.0 INTERNET PROTOCOL VERSION 6 (IPV6) COMPLIANCE

The Contractor solution shall support the latest Internet Protocol Version 6 (IPv6) based upon the directives issued by the Office of Management and Budget (OMB) on August 2, 2005 (http://www.whitehouse.gov/sites/default/files/omb/assets/omb/memoranda/fy2005/m05-22.pdf), September 28, 2010 (https://cio.gov/wp-content/uploads/downloads/2012/09/Transition-to- IPv6.pdf), and the DHS Enterprise Architecture (per OMB Memorandum M-21-07, November 19, 2020).

IPv6 technology, in accordance with the USGv6 Profile (NIST Special Publication (SP) 500-267 (http://www-x.antd.nist.gov/usgv6/index.html), the Technical Infrastructure for USGv6 Adoption (http://www.nist.gov/itl/antd/usgv6.cfm), and the NIST SP 800 series applicable

LAST UPDATED: 04/16/2025 PAGE 8/8

compliance (http://csrc.nist.gov/publications/PubsSPs.html) shall be included in all IT infrastructures, application designs, application development, operational systems and sub-systems, and their integration.

In addition to the above requirements, all devices shall support native IPv6 and/or dual stack IPv6 IPv4 connectivity without additional memory or other resources being provided by the Government so that they can function in a mixed environment. All public/external facing servers and services (e.g., web, email, DNS, ISP services, etc.) shall support native IPv6 and/or dual stack IPv6 IPv4 users, and all internal infrastructure and applications shall communicate using native IPv6 and/or dual stack IPv6 IPv4 operations.

8.0 USCG CYBERSECURITY COMPLIANCE

The Contractor must comply with all applicable cybersecurity requirements set forth in Attachment 5.