attachment_2_bid_207_24.pdf

I

2023 or newer John Deere 130P Excavator

Engine:

Rated Net Power shall be no less than 98HP @ 2000 RPM

Engine must be certified to EPA Final Tier 4/EU Stage IV.

Engine shall have 4 cylinders and a displacement of no less than 275 cu in (4.SL).

Engine shall have auto-idle mode to reduce engine speed when hydraulics are not in use to reduce fuel consumption and noise.

Engine shall be capable of auto-shutdown with adjustable delay periods to conserve fuel.

Engine must come standard with oil sampling valve.

Engine oil interval shall have a scheduled 500 hr interval for reduced operating costs.

Off-level capacity shall be no less than 35 degrees.

The engine oil and fuel filters will be remotely mounted for ease of access.

The engine will have a cold-start aid, such as glow-plug or equivalent.

The engine accessory drive belt will have an automatic tension device to reduce maintenance cost.

Cooling:

The cooling system shall be cool-on demand, using an electronically controlled fan that operates at a variable speed to reduce fuel consumption and noise.

The hydraulic coolers shall have no more than 10 fins per inch rating to resist plugging and for easier clean-out.

Cooling system shall be protected from debris by a pre-screen side shield.

Power Train:

The excavator will have two speed propel with auto-shift for smooth and fast operation.

The propel motor will be protected with a shield or guard.

There will be three power modes and one work mode to simplify a variety of applications.

Drawbar pull shall be at least 24,729 lb (11,217kg).

Brakes:

The propel brake will be spring applied, hydraulically released.

The swing brake will be spring applied, hydraulically released.

Hydraulic System:

2 Variable-Displacement Axial-Piston Hydraulic Pumps at 28 GPM, Each with a combination valve for high flow attachment through monitor.

Pilot pump w 8.7 GPM flow.

Factory auxiliary high flow lines w/ auxiliary relief pressure adjustment with electronic proportional auxiliary control.

The excavator will come equipped with a reduce-drift valve for boom down, arm in for full control.

Factory auxiliary hydraulic valve section to accommodate attachments.

Hydraulic sight gauge shall be provide for quick daily checks to reduce operating costs.

The auxiliary hydraulic flow will be adjusted through the monitor.

The excavator will be capable of boosting power to increase digging forces on the fly when needed.

The hydraulic system will have an oil-sampling valve will be provided as standard equipment.

Hydraulic return filter shall be positioned inside the hydraulic tank to protect form contamination when hydraulic oil is changed.

Swing speed shall be capable of 13.3 rpm for maximum productivity.

Swing torque shall be no less than 24,265 lb-ft (33 000 Nm)

Maximum system operating pressure for implement circuit shall be no more than 4980 psi (34 336 kPa) to minimize fatigue of the hydraulic components.

Maximum system operating pressure for travel circuits shall be no more than 4,980 psi {34 336 kPa).

Maximum system operating pressure for swing circuits shall be no more than 4685 psi {32 300 kPa).

The right joystick controller shall be pre-wired form the factory for auxiliary Proportional hydraulics.

The boom and arm shall be equipped with standard welded bosses or attachment luas for auxiliary high flow lines.

Hydraulic oil change interval shall be 5000 hours for reduced operating costs and increased productivity.

The excavator hydraulic tank will be cylindrical in shape to promote oil mix on return am minimize potential for leaks.

Case Drain hydraulic line to accommodate mulching head.

Factory Auxiliary Hydraulic oil cooler to accommodate HI-FLOW attachments.

Electrical:

The electrical system shall be 24 volt with 100 amp alternator.

The circuits shall be blade type multi-fused.

The battery shall have a positive battery cover.

Two LED (or equivalent) work lights shall be provided;

one mounted on the boom, one mounted on the frame.

Fuses shall be identified and color coded for correct amperage for fast replacement.

The machine performance and utilization data will be captured and stored by a data-acquisition system with software that can produce graphs showing machine utilization and performance history.

Right rear & Left rear camera system with right & left LED lighting.

Operator Station:

The operator station shall be mounted on four silicone-filled cab mounts or equivalent to reduce noise, vibration and operator fatigue.

The cab shall have an openable roof hatch to provide additional emergency escape path and clear visibility to overhead obstacles with a sunshade for operator comfort.

The operator will be provided with a conveniently located tool to break the window in case of an emergency.

The cab fresh air filter mut be accessible from the from the ground and outside of the cab and not require any tools for removal - other than the key to open door.

Cab shall have a 12-volt, 60 watt, 5 amp cell phone power outlet.

Seat shall be deluxe, adjustable, with suspension, headrest and adjustable lumbar support and 4-in (100 mm) adjustable armrests.

The control positions and the seat can be adjusted independently of each other for greater operator comfort.

The cab shall have auto-climate control, NC with heater and pressurizer.

System shall retain and display active fault codes and incidents related to machine operating outside of the specified parameter.

The monitor shall be capable of displaying information in a minimum of 10 different languages.

The monitor shall be capable of storing maintenance/ service interval information on items like engine oil, engine oil filter, hydraulic oil, hydraulic oil filter and air cleaner filter.

The monitor shall be capable of showing machine’s diagnostic information including error messages, fault codes and system operating information. Examples of operating information include, engine rpm, pump pressure, hydraulic oil temperatures and pilot pump pressures.

The horn and travel alarm shall be operable while the machine is moving forward and in reverse.

The AC filters shall be easy to replace with no special tools required and shall have extended replacement intervals.

Cab shall have a large beverage holder, and a hot/cold beverage box, installed at factory.

Engine air cleaner restriction light shall be standard on monitor.

The cab shall have auto climate control to maintain a comfortable, programmable temperature for AC and Heat.

The windshield washer/wiper will have constant and intermittent speed.

The right window of the cab must be glass.

The cab will have an AM/FM/radio installed from factory.

Undercarriage:

24" 600mm steel track with triple semi-grouser shoes & 8'6" wide backfill blade.

The undercarriage will have one upper carrier roller per side and seven lower roller per side.

The chain shall be sealed with lubricated and the track adjustment shall be hydraulic.

Upper structure:

The bucket-to-arm joint shall be coated with an extremely wear resistant surface like Tungsten-Carbide thermal coating.

Booms, arms and mainframes shall be warranted for 3 years or 10,000 hours.

The machine shall have oil-impregnated bushings to enhance durability and extend grease intervals to 500 hrs on the arm-and-boom joint and 100 hrs on the bucket joint.

The boom shall be reinforced with three welded bulkhead plates to deliver maximum strength and durability.

The outer mainframe of the house shall be constructed with reinforced O-channel for durability.

The cab door, fuel cap and service doors and tool box shall be lockable.

Right hand, left hand and counterweight mounted mirrors shall be standard.

The batteries must be located in sperate area other than the designated storage area or tool box and must have a battery shut off switch.

9'11" Long dig arm w Bucket cylinder & linkage

The machine will have dirt seals on all bucket pins.

Overall Machine Specs:

Standard minimum operating weight with blade shall be no less than 30,000 lbs.

Overall height to top of cab shall be no more than 9 ft O in .

Counterweight clearance shall be 2 ft 9in.

Operating Specifications:

The ISO arm digging force with a 9 ft 11 in arm shall be no less than 12,521 lb.

The ISO bucket digging force with a 9 ft 11 in arm shall be no less than 21.480 lb.

Lifting capacity over the side (al around level 15 ft reach with 9 ft 11 in arm, 913 lb bucket and 28 in triple semi-arouser shoes shall be no less than 6,750 lb.

Maximum digging depth with 9 ft 11 in arm shall not be less than 19 ft 11 in.

Attachments/options:

36" wide 0.75 cubic yard heaped capacity w liner:

severe duty digging bucket w 5 ESCO Ultra Lock Teeth and 1 set of bolt on ESCO style wear shrouds w wedge lock lugging.

Hydraulic wedge lock coupler.

Hydraulic Direct link 4 tine thumb with Hardox tines thumb, pivots on main stick pin.

60" 1.250 Cubic yard heaped capacity hydraulic tilt clean-up bucket with bolt on edge with wedge lock lugging & Stucchi quick couplers.

Hydraulics set up so equipment operator can switch from operating hydraulic thumb to operating hydraulic tilt clean up bucket without leaving the operator seat.

Under frame HD removable center guard.

Front removable window guard.

spare set of ESCO Ultra lock teeth U25S including a complete set of locks.

Hard copy of Parts and manuals

Stucchi couplers installed on excavator and attachments

Excavator slant top rub rails installed on both sides of excavator.

Warranty:

5 Year 2,500 hr manufactures full machine coverage

2024 INDECO IMH•10 36" Mulching Head

Craig Wedge Lock Lugging Adapter

1 Replacement knife kit with hardware

Stucchi Couplers