Attachment 1 - Salient Characteristics.pdf

Attachment 1 ‐ Salient Characteristics

SALIENT CHARACTERISTICS

Salient characteristics means those particular characteristics that specifically describe the essential physical and functional features of the material or service required. List all the minimum specification, characteristics, capabilities, etc. required for this supply.

Specified Values are Worst Case for the Integrated Chassis‐Level Tuner System (i.e., not just internal tuner modules), unless otherwise noted

Category Sub‐

Category Parameter Value Units Notes

General See Notes See notes

Rackmountable 4‐channel microwave tuner system.

Each channel accepts an RF input and provides dual analog IF outputs (tuned to same RF frequency):

1 GHz center with 500 MHz IF Bandwidth, 160 MHz with 80 MHz IF Bandwidth. The term "system" does not necessary mandate a single chassis solution.

Format and Packaging

Turn‐Key See Notes See notes

The government requires a turn‐key chassis‐level solution, mostly independent of underlying tuner platform/technology. Quotes/bids shall address obsolescence and/or support over 20+ years: this renders VME‐based solutions as undesirable.

Regardless of technology platform, turn‐key solution and bid will include all necessary subsystems (e.g., single‐board computer, Ethernet switch, rackmountable chassis, internal cables, etc.).

Modularity See Notes See notes

The government is requiring at least 4 independent tuning channels (where a "channel" consists of an RF input and dual IF outputs) within the physical space constraints specified below. Additionally, tuner channels shall be modular with a granularity of two tuner channels maximum. That is, tuner channels shall be field‐replaceable at one‐channel or, at most, two‐channels at a time. Single‐channel granularity is preferred unless dual‐channel allows significant relative cost reductions. Vendors may provide quotes for both single‐ and dual‐channel granularity solutions if so desired. Note that each tuner‐channel

SALIENT CHARACTERISTICS

Attachment 1 ‐ Salient Characteristics

Category Sub‐

Category Parameter Value Units Notes in a "dual‐channel granularity" system shall be able to be tuned independently.

See Notes See Notes

Required number of chassis and configuration shall be in accordance with the included "Chassis Configuration", depending on proposed modularity.

For Configuration Options 1 and 2, all chassis will be "4‐Channel Ready", where each chassis only requires additional tuner modules to become a 4‐channel system. For example, the chassis will be plumbed with all the necessary cables for 4‐channels.

Size/Power

Power Voltage 90‐240 VAC

Freq 60 Hz

Size

Format Rackmountable 19" EIA Rack

Height ≤4 RU Total ‐ for at least 4 Independent functional channels

Depth ≤24 in.

Interfaces

RF input SMA

1 GHz IF output

SMA

160 MHz IF output

SMA

10 MHz REF SMA/BNC

Control (SW) Ethernet Single port for 4‐channels preferred, but individual ports (or single port for 2‐channels) acceptable

Control (HW Strobe/Trig)

See notes

Each tuner channel shall have independent strobe/trigger control. The physical connector choice is up to vendor, but the interface shall be compliant with RS‐422 (e.g., accepts differential inputs)

Max RF Input Power Level

≥ 20 dBm No damage

Attachment 1 ‐ Salient Characteristics

Category Sub‐

Category Parameter Value Units Notes

Impedance

Impedance 50 ohms nominal: RF In, IF Out, REF In

Input VSWR ≤ 3.0:1 RF Ins

Output

VSWR

≤ 2.0:1 IF Outs

RF, IF

Performance

Tuning

Input Frequency Range

0.1‐18 GHz

Minimum range of accessible frequencies, not necessarily the range of center‐tune frequency values. It is highly desirable that this full range of tuned frequencies is accessible with both IF outputs.

If fully accessible with both IF outputs, please describe tuning behavior. If not fully accessible with both IF outputs, clarify what frequency ranges are compliant on each IF output.

Tuning Resolution

≤ 1 MHz

Tuning Speed

≤ 100 us Settled to within 100 KHz after hardware strobe applied or software command received

Gain

1 GHz IF: RF‐ IF Gain

≥ 20 dB nominal

1 GHz IF Output Gain Adjustment

≥ 20 dB Steps of ≤ 1 dB

160 MHz IF:

RF‐IF Gain

≥ 20 dB

160 MHz IF Output Gain Adjustment

≥ 20 dB Steps of ≤ 1 dB

Gain Flatness within 4.0 dB peak‐peak

Linearity and

Spurious

Input P1dB:

1 GHz IF Output

≥ ‐17 dBm at Max Gain

Input P1dB:

160 MHz IF Output

≥ ‐17 dBm at Max Gain

Input IP2: Fc <= 1100 MHz

≥ 35 dBm at Max Gain

Attachment 1 ‐ Salient Characteristics

Category Sub‐

Category Parameter Value Units Notes

Input IP2: Fc > 1100 MHz

≥ 50 dBm at Max Gain

Input IP3 ≥ ‐5 dBm at Max Gain

Spurs (single‐tone, in‐band): Fc > 750 MHz

≤ ‐58 dBc at input powers up to at least ‐20 dBm, at max gain

Spurs (single‐tone, in‐band): Fc <= 750 MHz

≤ ‐50 dBc at input powers up to at least ‐20 dBm, at max gain

Spurs:

internally‐ generated

≤ ‐80 dBm Input Referred (worst case)

Noise Figure ≤ 20 dB at Max Gain

LO

Reradiation

≤ ‐70 dBm

Image Rejection

≥ 60 dB

IF Rejection ≥ 60 dB

Tuner Inter‐ Channel Isolation

≥ 58 dB

Any channel‐channel cross‐talk, under worse case conditions (e.g., leaking channel signal at Input P1dB and/or Output P1dB power levels): treated as single‐ tone in‐band spurs

Reference

Frequency 10 MHz

External/Int ernal

See notes Has internal reference. Can accept External (via management or autosense)

Internal 10 MHz Stability within +/‐1 ppm

External 10 MHz power level

0±5 dBm accepts this range, at a minimum

SSB

Integrated Phase noise

≤ 0.5 ° RMS 100 Hz ‐ 10 MHz

Control Remote Control (SW)

See notes Fully configurable over vendor‐provided software interface. Includes the ability to query parameters and settings

Attachment 1 ‐ Salient Characteristics

Category Sub‐

Category Parameter Value Units Notes

Hardware‐ Based Tuning

See notes

Users shall be able to control the tune frequency through an external hardware (HW) strobe/trigger (in addition to the SW interface). While HW‐controlled, the tuners shall be able to step through a predefined "tuner table" upon every receipt of a strobe. Via the SW interface, users shall be able to create a "tune table" of at least 256 entries. Each entry shall include center tuner frequency, RF attenuation and IF attenuation values.

Environmental

Operating Temp.

Range

0‐50 ° C Ambient: must operate over this range, at a minimum

Humidity 0‐95 % non‐condensing

Documentation See Notes See Notes

Vendor shall provide Operator/Maintenance Manual and Programming/SW Manual. Vendor shall provide documentation/procedures for replacing tuner channels in the field (if applicable).

GUI GUI See notes Vendor shall provide a working graphical user interface (e.g., stand‐alone application, web‐based, etc.)

Vendor Quality Control

See Notes See Notes ISO 9001 Certification

Unit Test/ Compliance

See Notes See Notes

At time of delivery, suppliers will provide test documentation verifying compliance with all performance requirements via factory acceptance tests. Noncompliant units may not be accepted.

Attachment 1 ‐ Salient Characteristics

Chassis Configuration Options

Spare Tuner Cards (no chassis)

Tuner Channel 16

Tuner Channel 17

Tuner Channel 18

Chassis 3

Tuner Channel 9

Tuner Channel 10

Tuner Channel 11

Tuner Channel 12

Chassis 4 Chassis 6

Tuner Channel 1

Tuner Channel 2

Tuner Channel 3

Tuner Channel 4

Chassis 1 Chassis 2

Tuner Channel 5

Tuner Channel 6

Tuner Channel 7

Tuner Channel 8

Tuner Channel 25

Tuner Channel 26

Tuner Channel 27

Tuner Channel 28

Solutions that are based on Chassis/Cards with Single Tuner Channel Granuality (e.g., VPX)

Tuner Channel 24

Tuner Channel 23

Tuner Channel 19

Tuner Channel 20

Tuner Channel 21

Chassis 7

Tuner Channel 22

Tuner Channel 13

Tuner Channel 14

Tuner Channel 15

Chassis 5

Attachment 1 ‐ Salient Characteristics

Spare Tuner Cards (no chassis)

Chassis 5 Chassis 6

Solutions that are based on Chassis/Cards with Dual Tuner Channel Granuality (e.g., VPX)

Chassis 1 Chassis 2 Chassis 3

Tuner Channels

22/26

Tuner Channels

27/28

Tuner Channels

15/23

Tuner Channels

16/17

Tuner Channels

18/24

Tuner Channels

19/20

Tuner Channels

21/25

Chassis 7

Tuner Channels

1/2

Tuner Channels

3/4

Tuner Channels

5/6

Tuner Channels

7/8

Tuner Channels

9/10

Tuner Channels

11/12

Tuner Channels

13/14

Chassis 4

Attachment 1 ‐ Salient Characteristics

Solutions that are based on Non‐Modular Chassis with Single Tuner Channel per Chassis

Chassis 1

Tuner Channel 1

Chassis 2

Tuner Channel 2

Chassis 3

Tuner Channel 3

Chassis 7 Chassis 8 Chassis 9

Tuner Channel 7 Tuner Channel 8 Tuner Channel 9

Chassis 4 Chassis 5 Chassis 6

Tuner Channel 4 Tuner Channel 5 Tuner Channel 6

Chassis 13 Chassis 14 Chassis 15

Tuner Channel 13 Tuner Channel 14 Tuner Channel 15

Chassis 10 Chassis 11 Chassis 12

Tuner Channel 10 Tuner Channel 11 Tuner Channel 12

Tuner Channel 19 Tuner Channel 20 Tuner Channel 21

Chassis 16 Chassis 17 Chassis 18

Tuner Channel 18 Tuner Channel 17 Tuner Channel 18

Chassis 28

Tuner Channel 28

Chassis 25 Chassis 26 Chassis 27

Tuner Channel 25 Tuner Channel 26 Tuner Channel 27

Chassis 22 Chassis 23 Chassis 24

Tuner Channel 22 Tuner Channel 23 Tuner Channel 24

Chassis 19 Chassis 20 Chassis 21

Attachment 1 ‐ Salient Characteristics

Solutions that are based on Non‐Modular Chassis

Dual Tuner Channels per Chassis

Chassis 1

Tuner Channels

1/2

Chassis 2 Chassis 3

Tuner Channels

3/4

Tuner Channels

5/6

Chassis 7 Chassis 8 Chassis 9

Tuner Channels

13/14

Tuner Channels

15/16

Tuner Channels

17/18

Chassis 4 Chassis 5 Chassis 6

Tuner Channels

7/8

Tuner Channels

9/10

Tuner Channels

11/12

Chassis 13 Chassis 14

Tuner Channels

25/26

Tuner Channels

27/28

Chassis 10 Chassis 11 Chassis 12

Tuner Channels

19/20

Tuner Channels

21/22

Tuner Channels

23/24