Att 1_WBM Specification.pdf

Attachment 1 – WB DOCKING SPECIFICATION, Rev - N00024-21-R-2255

Attachment 1

WORK BOAT MEDIUM (WB-M)

COMMANDER, NAVY INSTALLATIONS

COMMAND (CNIC)

SPECIFICATION

REV -

30 March 2021

Attachment 1 – WB MEDIUM SPECIFICATION, Rev - N00024-21-R-2255 ii

REVISION HISTORY

Date Summary Of Change Hull

Applicability Version

30 March 2021 Initial Issue Hull 2101+ -iii

TABLE OF CONTENTS

SECTION 0: GENERAL GUIDANCE AND ADMINISTRATION

040 INTRODUCTION AND GENERAL DESCRIPTION

040-1 BACKGROUND

040-2 DEFINITIONS

042 GENERAL ADMINISTRATIVE REQUIREMENTS

042-1 GENERAL REQUIREMENTS

042-2 OPERATIONAL PROFILE

042-3 REFERENCED DOCUMENTS

042-4 ALTERNATE ITEMS

042-5 ORDER OF PRECEDENCE

042-6 STATEMENT OF WORK (SOW)

050 BOAT PERFORMANCE

050-1 BOAT PERFORMANCE

070 GENERAL REQUIREMENTS OF DESIGN AND CONSTRUCTION

070-1 BOAT CHARACTERISTICS

070-2 ENVIRONMENTAL CONDITIONS

070-3 LOAD CONDITIONS

070-4 ABYC STANDARDS

070-5 ALTERATIONS

070-6 SEAKEEPING, DYNAMIC STABILITY, AND MANEUVERABILITY

070-7 CONFIGURATION MANAGEMENT

070-8 INSTALLATION OF EQUIPMENT, MACHINERY, AND MATERIALS

071 ACCESS

071-1 ACCESSIBILITY

071-2 BILGE ACCESS

073 NOISE, VIBRATION, AND RESILIENT MOUNTINGS

073-1 NOISE LEVELS (EXTERIOR)

073-2 NOISE LEVELS (INTERIOR)

073-3 RESILIENT MOUNTS

074 WELDING AND ALLIED PROCESSES

074-1 GENERAL

074-2 VISUAL INSPECTIONS

074-3 DYE PENETRANT TESTING (PT)

074-4 RADIOGRAPHIC TESTING (RT) AND ULTRASONIC TESTING (UT)

075 FASTENERS

075-1 STAINLESS STEEL FASTENERS

iv

078 MATERIALS

078-1 STRUCTURAL MATERIAL

078-2 PIPING SYSTEM MATERIALS

078-3 CORROSION CONTROL

078-4 BEDDING COMPOUND

078-5 NON-BIODEGRADABLE MATERIALS

078-6 FABRIC MATERIAL

078-7 FIRE RETARDANT INTERIOR MATERIALS

079 STABILITY

079-1 INTACT STABILITY

084 TRANSPORTATION AND HANDLING

084-1 ROAD TRANSPORT

084-2 MARITIME TRANSPORT

084-3 BOAT TIEDOWN FITTINGS

084-4 WATER PROOF COVER

085 TECHNICAL DATA PACKAGE (TDP)

085-1 TECHNICAL DESIGN ANALYSES

085-2 DRAWINGS

085-3 BILL OF MATERIALS (BOM)

085-4 COMMERCIAL OFF THE SHELF TECHNICAL MANUALS AND DOCUMENTATION

085-5 BOAT TECHNICAL MANUAL

085-6 OEM CERTIFICATIONS

085-7 OEM WARRANTIES BOOKLET

085-8 ESSENTIAL CYBERSECURITY COMPONENTS (ECSC) DOCUMENTATION

085-9 TESTS AND TRIALS REPORTS

085-10 MASTER DATA INDEX

092 TESTING

092-1 GENERAL

092-2 TEST CERTIFICATIONS

094 TRIALS

094-1 BUILDER'S TRIALS

094-2 PRE-DELIVERY INSPECTION AND TRIALS (PDIT) [OPTION – IF ORDERED]

094-3 STEERING AND MANEUVERING TRIALS

099 PHOTOGRAPHS

099-1 PHOTOGRAPHS

SECTION 1: HULL STRUCTURE

100 GENERAL REQUIREMENTS FOR HULL STRUCTURE

v

100-1 GENERAL STRUCTURAL REQUIREMENTS

100-2 LIMBER HOLES

114 SKEGS

114-1 SKEGS

130 HULL DECKS

130-1 DECK DRAINAGE

150 DECK HOUSE STRUCTURES

150-1 HULL STYLE: CABIN

150-2 CABIN EMERGENCY EGRESS

167 HULL STRUCTURAL CLOSURES

167-1 DOORS AND HATCHES

167-2 ENGINE ROOM EMERGENCY EGRESS ROUTES

167-3 EQUIPMENT REMOVAL

169 SPECIAL PURPOSE CLOSURES AND STRUCTURES

169-1 BOW PUSHER KNEES

SECTION 2: PROPULSION

200 GENERAL REQUIREMENTS FOR PROPULSION PLANT

200-1 PROPULSION PLANT

233 INBOARD ENGINE

233-1 INBOARD DIESEL ENGINES

233-2 ENGINE DIAGNOSTICS [OPTION – IF ORDERED]

241 PROPULSION REDUCTION GEARS

241-1 MARINE GEAR

243 PROPULSION SHAFTING, SEALS AND BEARINGS

243-1 PROPULSION SHAFTING

245 PROPELLERS

245-1 PROPELLERS

252 PROPULSION CONTROL SYSTEM

252-1 PROPULSION INSTRUMENT MARINE PACKAGE (INTEGRATED)

256 ENGINE COOLING SYSTEM

256-1 ENGINE COOLING SYSTEM

256-2 ENGINE AUXILIARY FRESH WATER RUN AND FLUSH CONNECTION

259 EXHAUST SYSTEM

259-1 ENGINE EXHAUST (DRY)

262 MAIN PROPULSION LUBE OIL SYSTEM

262-1 ELECTRIC FAST LUBE OIL CHANGE SYSTEM (FLOCS)

SECTION 3: ELECTRIC PLANT

vi

300 GENERAL REQUIREMENTS FOR ELECTRIC PLANT

300-1 SUITABLE FOR MARINE ENVIRONMENT

300-2 PANEL COVERS

300-3 BONDING SYSTEM

300-4 SWITCHES

300-5 ENCLOSURES

303 PROTECTIVE DEVICES

303-1 DC OVERCURRENT PROTECTION

303-2 AC OVERCURRENT PROTECTION

304 ELECTRICAL CABLE, WIRING, AND CONNECTIONS

304-1 WATERTIGHT CONNECTIONS

304-2 CABLE SUPPORTS

304-3 MARINE MULTI-CONDUCTOR CABLE

304-4 ELECTRICAL CONNECTIONS

304-5 WEATHERPROOFED CONNECTORS

304-6 WATERTIGHT CABLE PENETRATIONS

313 BATTERIES

313-1 BATTERIES

313-2 BATTERY CHARGING (24 VDC ALTERNATORS)

313-3 BATTERY VOLTMETER

313-4 SHORE POWER BATTERY CHARGER (120 VAC TO 24 VDC)

314 POWER CONVERSION EQUIPMENT

314-1 120 VAC INVERTER

320 POWER DISTRIBUTION SYSTEMS

320-1 DC POWER DISTRIBUTION SYSTEM

320-2 AC POWER DISTRIBUTION

320-3 SHORE POWER SYSTEM (120 VAC, 60 HZ)

320-4 OUTLETS (12 VDC)

320-5 WATERTIGHT OUTLETS

320-6 OUTLETS (120 VAC GFCI)

324 ELECTRICAL PANELS

324-1 ELECTRICAL CIRCUIT BREAKER PANELS

330 LIGHTING

330-1 ELECTRONIC DIMMER

330-2 INTERIOR LED LIGHTING (24 VDC)

330-3 DECK LOW LEVEL LIGHTING

330-4 DECK WORK LIGHTS

vii

330-5 ELECTROMAGNETIC COMPATIBILITY

SECTION 4: COMMAND AND CONTROL

400 GENERAL REQUIREMENTS FOR COMMAND AND CONTROL

400-1 FLUSH MOUNT EQUIPMENT SERVICE CLEARANCES

405 ANTENNA REQUIREMENTS

405-1 GENERAL REQUIREMENTS

421 NON-ELECTRICAL NAVIGATION AIDS

421-1 MAGNETIC COMPASS

421-2 STORAGE

421-3 NAVIGATIONAL WORK SURFACE

422 ELECTRICAL NAVIGATION AIDS

422-1 NAVIGATION LIGHTS

422-2 DAY SHAPE MAST

422-3 INTEGRATED ELECTRONIC NAVIGATION PACKAGE

422-4 SPOTLIGHT, HANDHELD

422-5 SPOTLIGHTS, FIXED MOUNT

422-6 ELECTRONIC HARBOR SECURITY SYSTEM (EHSS)

433 ANNOUNCING SYSTEMS

433-1 INTERCOM (SOUND POWERED)

436 ALARM, SAFETY, AND WARNING SYSTEMS

436-1 BILGE FLOODING ALARM SYSTEMS

436-2 CARBON MONOXIDE (CO) DETECTION SYSTEM

441 RADIO SYSTEMS

441-1 PRIMARY VHF RADIO

441-2 SECONDARY VHF RADIO

441-3 ENTERPRISE LAND MOBILE RADIO (ELMR)

443 VISUAL AND AUDIBLE COMMUNICATION SYSTEMS

443-1 NAVIGATION HORN

SECTION 5: AUXILIARY SYSTEMS

500 GENERAL REQUIREMENTS FOR AUXILIARY SYSTEMS

505 GENERAL REQUIREMENTS FOR FLUID SYSTEMS

505-1 FLUID SYSTEM CONNECTIONS

505-2 THROUGH-HULL FITTINGS AND VALVES

505-3 FLUID SYSTEMS

505-4 PIPING INSTALLATION

505-5 HOSE INSTALLATION

505-6 HOSE CLAMPS

viii

511 COMPARTMENT HEATING SYSTEMS

511-1 COLD WEATHER PACKAGE [OPTION – IF ORDERED]

512 MANNED COMPARTMENT VENTILATION SYSTEMS

512-1 MANNED COMPARTMENT FRESH AIR VENTILATION

512-2 DEFOGGING AND DEFROSTING SYSTEM

512-3 CABIN FANS

512-4 CONSOLE VENTILATION

513 MACHINERY SPACE VENTILATION SYSTEMS

513-1 ENGINE ROOM VENTILATION

514 HEATING, VENTILATION, AND AIR CONDITIONING (HVAC) SYSTEMS

514-1 CABIN HEATING AND AIR CONDITIONING

529 BILGE DRAINAGE SYSTEM

529-1 EMERGENCY ENGINE ROOM DEWATERING SYSTEM

529-2 FIXED MANUAL BILGE PUMP

529-3 ELECTRIC BILGE PUMP(S)

541 FUEL SYSTEM

541-1 FUEL TANK(S)

541-2 FUEL SOUNDING

541-3 FUEL LEVEL GAUGE

541-4 FUEL VALVES

541-5 REMOTE FUEL SHUTOFF

541-6 FUEL-WATER SEPARATOR AND FILTER

541-7 FUEL FILL AND VENT SYSTEM

541-8 FUEL STRIPPING SYSTEM

555 FIRE FIGHTING

555-1 ENGINE ROOM FIXED, CLEAN AGENT FIRE EXTINGUISHING SYSTEM

555-2 PORTABLE FIRE EXTINGUISHERS

556 HYDRAULIC SYSTEMS

556-1 HYDRAULIC SYSTEMS

561 STEERING CONTROL SYSTEMS

561-1 HYDRAULIC STEERING

561-2 EMERGENCY STEERING

562 RUDDERS

562-1 RUDDERS

581 ANCHOR HANDLING

581-1 ANCHOR FITTINGS

582 MOORING AND TOWING SYSTEMS

ix

582-1 FORWARD AND AFT TOWING BITTS

582-2 SHOULDER AND QUARTER H-BITTS

582-3 CHOCKS

582-4 DECK WINCH SYSTEM

589 SPECIAL PURPOSE SYSTEMS

589-1 DAVIT

592 SWIMMER AND DIVER SUPPORT SYSTEMS

592-1 REBOARDING LADDER

592-2 MAN OVERBOARD (MOB) RECOVERY

SECTION 6: OUTFIT AND FURNISHINGS

600 OUTFIT

600-1 BOAT HOOK

600-2 RING BUOYS

600-3 U.S. FLAG AND MAST

600-4 MOORING LINES

600-5 FIRST AID KIT

600-6 EMERGENCY POSITION INDICATING RADIO BEACON (EPRIB)

602 LABELING

602-1 HULL REGISTRY NUMBER (HRN)

602-2 LABEL PLATES (GENERAL)

602-3 PIPING SYSTEM LABEL PLATES

602-4 VALVE LABEL PLATES

602-5 INSTRUCTION LABEL PLATES

602-6 HOISTING LABEL PLATES

602-7 BOAT INFORMATION LABEL PLATE

602-8 BOAT ALTERATION LABEL PLATE

602-9 SHIPPING DATA LABEL PLATE

602-10 IN-SERVICE LABEL PLATE

602-11 SYSTEMS LABEL PLATES

602-12 STOWAGE LABEL PLATES

602-13 TOW FITTING LABEL PLATES

602-14 NOISE WARNING SIGNS

602-15 UNIQUE ITEM IDENTIFICATION (UID)

611 HULL FITTINGS

611-1 DECK TIEDOWNS

611-2 FENDERING

611-3 BOAT HOISTING FITTINGS

x

611-4 CABIN HOISTING FITTINGS

611-5 BOAT HOISTING SLING

611-6 BOAT HOISTING HARDWARE

612 RAILS, STANCHIONS, AND LIFELINES

612-1 GRAB RAILS

625 WINDOWS

625-1 WINDSHIELD WIPER AND WASHER SYSTEM

631 PAINTING

631-1 BOTTOM PAINT

631-2 TOPSIDE PAINT

631-3 INTERIOR PAINT

631-4 EXTERIOR NON-SKID

633 CATHODIC PROTECTION

633-1 ANODES

634 DECK COVERING

634-1 ANTI-FATIGUE MATTING (INTERIOR)

634-2 DIAMOND TREAD OR GRATING

635 HULL INSULATION

635-1 THERMAL INSULATION AND ACOUSTICAL TREATMENT (GENERAL)

635-2 THERMAL INSULATION

662 WORKING SPACES AND SEATING

662-1 CONSOLE ERGONOMICS

662-2 SEATING – CREW

670 STOWAGE SPACES

670-1 STOWAGE

670-2 DECK STOWAGE BOX

SECTION 0: GENERAL GUIDANCE AND ADMINISTRATION

040 INTRODUCTION AND GENERAL DESCRIPTION

040-1 Background

Commander, Navy Installations Command (CNIC) has overall shore installation management responsibility in support of Naval operations worldwide. The mission of the CNIC Work Boat Medium (WB-M) is to provide Naval shore installations with capability to meet various port operations and barrier tending requirements. This includes the ability to safely assist vessels, open and close security barriers, and to tow and push floating port operations support equipment. In order to meet these objectives, the boat must include propulsion equipment that is maximized for bollard pull, be highly maneuverable with low freeboard, be capable of maritime and road transport, and include a cabin that is climate controlled and that provides shelter for the operators from extreme weather. CNIC boats are centrally procured via the US Navy Boat and Craft Program Office, PEO SHIPS (PMS 325G).

040-2 Definitions

Accessible: Components are “accessible” if they are capable of being reached for inspection, removal, or maintenance without the removal of permanent boat structure.

Cruise Speed: Cruise speed shall be defined by the OEM, typically 200 RPM less than the maximum rated engine RPM.

Deep Water: a water depth of 0.8 (LOA) or greater.

Idle Speed: Idle speed shall be the speed of the boat at the idle RPM of the engines.

Maximum Rated Power: The boat in the bollard condition with 100% throttle setting (maximum engine load).

Readily Accessible: Components are “readily accessible” if they are capable of being reached quickly and safely for effective use under emergency conditions without the use of tools.

Significant Wave Height: the average wave height (measured from trough to crest) of the highest 1/3 of waves present.

Sprint Speed: Boat speed at 100% throttle setting (maximum engine RPM).

042 GENERAL ADMINISTRATIVE REQUIREMENTS

042-1 General Requirements

This Specification is for United States Navy (USN) WB-M that includes the following characteristics:

Steel hull.

Removable aluminum cabin with heating, ventilation, and air conditioning systems

(HVAC).

Twin diesel inboard engines with marine gear.

Nozzled propellers.

Forward and aft towing fittings.

Personnel capacity of 8 (coxswain, 2 deckhands, and 5 passengers), normal crew of 3 (coxswain and 2 deckhands).

Removable cabin and pusher knees for transportation and maintenance.

The nominal hull length (welded structure only) is 29-30 feet (ft).

The expected service life for the boats delivered under this Specification is a minimum of 20 years.

The service life may be extended with major overhauls including replacement of propulsion systems, mechanical systems, electrical systems and hull repair.

Specifications identified in this section provide the minimum required general system characteristics and requirements for the selection, installation, onboard performance, onboard inspection of machinery, equipment and outfit, and pre-installation handling and inspections of materials for construction.

042-2 Operational Profile

The CNIC WB-M will have an Operational Profile defined as follows:

Speed Operational Percentage

Idle: 70%

Cruise: 20%

Maximum Rated Power: 10%

042-3 Referenced Documents

The following standards and specifications are referenced in this Specification. Where reference is made to a voluntary compliance or best practice standard, the recommended standards and practices shall be considered mandatory under this Contract.

46 CFR Part 111.60, Wiring Materials and Methods

46 CFR Part 160.041, Kits, First-Aid, for Merchant Vessels

46 CFR Part 164.109, Non-combustible Materials

46 CFR 160.150, Specification for Lifebuoys, SOLAS

46 CFR Part 180.70, Ring Life Buoys

49 CFR Part 393.102, What are the Minimum Performance Criteria for Cargo Securement Devices and Systems?

ABS, Rules for Building and Classing Steel Vessels Under 90 Meters in Length, 2019

ABYC, Standards and Technical Information Reports for Small Craft

ASME Y14.100, Engineering Drawing Packages

ASTM A27, Standard Specification for Steel Castings, Carbon, for General Application

ASTM A36, Standard Specification for Carbon Structural Steel

ASTM A53, Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

ASTM A106, Standard Specification for Seamless Carbon Steel Pipe for High- Temperature Service

ASTM A182, Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

ASTM A213, Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

ASTM A276, Standard Specification for Stainless Steel Bars and Shapes

ASTM A312, Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

ASTM A351, Standard Specification for Castings, Austenitic, for Pressure-Containing Parts

ASTM A500, Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

ASTM A501, Standard Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

ASTM A607, Standard Specification for Steel, Sheet and Strip, High-Strength, Low-Alloy, Columbium or Vanadium, or Both, Hot-Rolled and Cold-Rolled (Withdrawn 2000)

ASTM A668, Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

ASTM B466, Standard Specification for Seamless Copper-Nickel Pipe and Tube

ASTM B467, Standard Specification for Welded Copper-Nickel Pipe

ASTM B584, Standard Specification for Copper Alloy Sand Castings for General Applications

ASTM B928, Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments

ASTM C1338, Standard Test Method for Determining Fungi Resistance of Insulation materials and Facings

ASTM F593, Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

ASTM F594, Standard Specification for Stainless Steel Nuts

ASTM F1166, Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities

DOD-HDBK-743, Anthropometry of U.S. Military Personnel

FED-STD-595C, Colors Used in Government Procurement

IACS Publication No. 47, Shipbuilding and Repair Quality Standard

IEC 60529, Degrees of Protection Provided by Enclosures (IP Code)

IEEE 45, Recommended Practice for Electric Installations on Shipboard

IEEE 1580, Recommended Practice for Marine Cable for Use on Shipboard and Fixed or Floating Facilities

International Regulations for Preventing Collision at Sea, 1972 (72 COLREGS) which are contained in “USCG Navigation Rules and Regulations Handbook”, U.S. Coast Guard Navigation Standards Branch, U.S. Coast Guard Headquarters, Washington, DC

ISO 12215-6, Small Craft – Hull Construction and Scantlings - Part 6: Structural arrangements and details

ISO 2533:1975, Standard Atmosphere

MIL-DTL-24779D, Detail Specification for Anodes, Sacrificial, Aluminum Alloy

MIL-DTL-3950, General Specification for Switches, Toggle, Environmentally Sealed

MIL-PRF-23236, Coating Systems for Ship Structures

MIL-PRF-24635, Coating Systems, Weather-Resistant, Exterior Use

MIL-PRF-24647, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24667C, Coating System, Non-Skid, for Roll, Spray, or Self-Adhering Application

MIL-STD-1366E, Interface Standard for Transportability Criteria

MIL-STD-1474E, Design Criteria Standard Noise Limits

MIL-STD-2003-1A(SH), Electric Plant Installation Standard Methods for Surface Ships and Submarines (Cable)

MIL-STD-2035A, Nondestructive Testing Acceptance Criteria

MIL-STD-209K, Interface Standard for Lifting and Tiedown Provisions

MIL-STD-810H, Environmental Engineering Considerations and Laboratory Tests

NAVSEA 0900-LP-060-4010, Fabrication, Welding and Inspection of Metal Boat and Craft Hulls

NAVSEA S6430-AE-TED-010, Technical Manual for Piping Devices and Flexible Hose Assemblies

NAVSEA T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods

NAVSEA TO300-AU-SPN-010A, Fabrication, Welding and Inspection of Small Boats and Craft, Aluminum Hulls

NAVSEA Drawing no. 803 5184106, Standard Navy Docking Drawing

NAVSEACOMBATSYSENGSTA Report No. 6660-99 Rev. A, Procedures Manual for Stability Analysis of U.S. Navy Small Craft

NSWCCD-23-TM-2009/33 Rev B, Hoisting System Design and Certification Process Guidance

NSWCCD-23-TM-2009/58 Rev B, U.S. Navy Boat Electrical Practices

NSWCCD-23-TM-2009/61 Rev A, U.S. Navy Boat Example Data Package

NSWCCD-23-TM-2009/64 Rev C, Small Craft Transportability Design and Certification Process Guidance, NSWCCD-23-TM-2009/65 Rev C, Towing Fitting Design and Certification Process Guidance, NSWCCD-23-TM-2011/05 U.S. Navy Craft Mechanical Practices

NSWCCD-23-TM-2011/38 Rev A, Mooring Fitting Design and Verification Process Guidance

NSWCCD-23-TM-2011/39 Rev A, Anchoring System Design and Verification Process Guidance

NSWCCD-80-TR-2014/038, Weight Management Process Guidance for Boats and Craft

NSWCCD-83-TM-2020/10, Essential Cybersecurity Components (ECSC) Data Collection and Documentation

RR-C-271D, Chains and Attachments, Carbon and Alloy Steel

SAE J1508, Hose Clamp Specifications

SAE J1273, Recommended Practices for Hydraulic Hose Assemblies

SAE J1527, Marine Fuel Hoses

SAE J1942, Hose and Hose Assemblies for Marine Applications

SAE J20, Coolant System Hoses

SAE J516, Hydraulic Hose Fittings

SNAME T&R Bulletin 4-16, Recommended Practices for Ship Heating, Ventilation & Air Conditioning Design Calculations

UL 489, Molded-Case Circuit Breakers, Molded-Case Switches, and Circuit-Breaker Enclosures

UL 1426, Standard for Electrical Cables for Boats

UL 2034, Standard for Single and Multiple Station Carbon monoxide Alarms

042-4 Alternate Items

Where boat components and equipment are specified by brand name or manufacturer and model number or equal, such identification is intended to be descriptive, not restrictive, and is intended to indicate the required characteristics of the product.

Note: The Government will not accept alternate items for brand name or manufacturer and model specified in the following Sections:

233 Inboard Diesel Engine

241 Marine Gear

422 Integrated Electronic Navigation Package

441 Radio Systems

529 Electric Bilge Drainage Systems

600 Emergency Position Indicating Radio Beacon (EPIRB)

Except as listed directly above, the Contractor may propose the use of other products which are equal to the specified make and model products. The following general requirements shall form the basis for determining the equality of alternate products unless additional specific or alternate requirements are designated within the applicable sections of these specifications:

The major attributes of form, fit, function, interface, and material of an alternate item shall not degrade the performance of the system within which it is used; nor the boat as a whole.

The alternate item shall require no more space or volume than the designated item for installation, operation, or maintenance. The alternate item shall weigh no more than the designated item. The connection fittings required to incorporate the alternate item into a system shall be identical to those necessary to incorporate the specified item. The principles of operation of the alternate item shall be the same as those of the designated item (i.e., hydraulic cylinders shall not be used in lieu of springs, etc.). Input power, capacity, and other operating requirements for the alternate item shall be no greater than those required by the designated item. Output power, capacity, and other performance parameters of the alternate item shall be no less than those required for the designated item and not so much greater than those of the designated item as to require an increased capacity of the system within which the item is installed.

The materials of construction of the alternate item shall be the same as those of the designated item unless the Contractor can demonstrate to the Government that the proposed alternate material will not adversely affect performance or service life of the item, the system within which it is installed, or the boat as a whole.

The reliability and maintainability of an alternate item shall be equal to or better than the specified item. The Contractor shall provide evidence of the equality of the reliability and maintainability of the alternate item to the specified item. This evidence may include such things as results of testing, service histories, documentation of successful use in similar applications, planned maintenance requirements, etc. Where the reliability and maintainability of the specified item has been established by testing, the government may require that the alternate item undergo similar testing to demonstrate its reliability and maintainability. Such testing, if required, shall be at the Contractor's expense.

An alternate item shall conform to the same industry or government specifications or standards as the specified item. Where a specified item has been approved or certified by a regulatory or testing agency, such as USCG or Underwriters' Laboratories, the alternate item shall also be approved or certified. The cost of demonstrating compliance with specifications or standards, or of obtaining approval or certification, shall be borne by the Contractor.

If the specified item is one with established Government logistic support, any alternative item shall have equivalent logistic support. If equivalent logistic support has not been established for the alternate item, the Contractor shall bear the expense of establishing equivalent support. Logistic support shall include, as applicable: maintenance planning and analysis; training and training support, including training equipment, curricula, and instruction materials; supply support; support equipment such as special tools and test equipment; technical documentation including technical manuals, Product Technical Description (PTD), Planned Maintenance System (PMS), Technical Repair Standards (TRS), and software documentation; computer resource support; facilities for maintenance and training; unique packaging, handling, storage, and transportation requirements; and human engineering considerations.

042-5 Order of Precedence

In case of inconsistency between the requirements of the Contract, this Specification, and the documents referenced in this Specification, the following order of precedence applies:

1. Contract requirements,

2. Specification requirements,

3. Other Government specifications and standards, industry standards, and similar referenced documents.

The following are not considered inconsistencies subject to an order of precedence determination:

a. Silence of one document with respect to details shown in another.

b. Broad boat requirements compared to detailed system or component requirements.

042-6 Statement of Work (SOW)

This Specification is written to be used in conjunction with the SOW. Additional requirements such as warranty, packaging, delivery, training, et cetera are defined in the SOW.

050 BOAT PERFORMANCE

050-1 Boat Performance

Unless otherwise specified, boat performance requirements shall be met in calm, deep water, Full Load condition (Section 070), International Standards Organization (ISO) Standard 2533:1975 “Standard Atmosphere” conditions. Performance requirements shall be as follows:

Bollard Thrust in the forward direction in Minimum Operating (Min Op) Condition: 16,000 pounds (lbs) (minimum)

Bollard Thrust in the reverse direction in Min Op Condition: 10,000 lbs (minimum)

Sprint Speed: 6.5 knots (minimum)

070 GENERAL REQUIREMENTS OF DESIGN AND CONSTRUCTION

070-1 Boat Characteristics

Offeror to provide all parameters below in Attachment 2.

Length Overall (LOA) including fendering and appendages: {{xx.xx}} ft

Hull Length (welded structure only): {{xx.xx}} ft o [Shall be no less than 29 ft and no greater than 30 ft]

Beam Overall (BOA) including fendering: {{xx.xx}} ft o [Shall not exceed 15 ft per Section 084]

Maximum Beam (welded structure only): {{xx.xx}} ft

Height, Lowest appendage (skeg) to Fixed Structure: {{xx.xx}} ft

Height, Lowest appendage to Moveable Structure (highest mast or antenna): {{xx.xx}} ft

Air Draft, Min Op Condition waterline to fixed Structure: {{xx.xx}} ft o [Shall not exceed 13 ft]

Height when rigged for transport (cabin and pusher knees removed): {{xx.xx}} ft o [Shall not exceed 11 ft per Section 084]

Width when rigged for transport: {{xx.xx}} ft o [Shall not exceed 15 ft per Section 084]

Total Installed Fuel Capacity: {{xxx}} gallons o [Shall be minimum of 400 gallons per Section 541]

Full Load Displacement: {{xx,xxx}} lbs including {{x}}% construction or build margin or both

Longitudinal Center of Gravity (LCG) in Full Load: {{xx.xx}} ft forward of transom and keel intersect.

Static Full Load Draft (hull): {{x.xx}} ft

Static Full Load Draft (to skegs): {{xx.xx}} ft o [Shall not exceed 8 ft]

Static Full Load Freeboard at the transom in the Min Op Condition: {{xx.xx}} ft o [Shall not exceed 25 inches]

Bollard Thrust in the forward direction in Min Op Condition: {{x,xxx}} o [Shall be minimum of 16,000 lbs per Section 050]

Bollard Thrust in the aft direction in Min Op Condition: {{x,xxx}} o [Shall be minimum of 10,000 lbs per Section 050]

Sprint Speed {{xx.x}} at Full Load in calm water o [Shall be minimum of 6.5 knots per Section 050]

070-2 Environmental Conditions

The boat shall be capable of operating in ambient air temperatures between 0°F and 105°F and water temperatures between 28°F and 95°F.

The boat shall be capable of full operation in conditions up to 2.9 ft significant wave height. The boat shall be capable of full operation in sheltered and coastal waters with wind speed of up to 40 knots.

The boat shall survive conditions up to 6.9 ft significant wave height with at minimum headway speed. Survive means remain upright and intact and make headway, but heading is driven completely by sea conditions.

070-3 Load Conditions

The following load conditions are defined for reference throughout this Specification. These definitions apply to the engineering design values for weight and moments of the boat in the described condition. Weight Management Process Guidance for Boats and Craft, NSWCCD-80- TR-2014/038 shall be used for guidance.

Service Life Allowance (SLA): The SLA shall be 800 lbs. For hoisting design purposes, 200 lbs of the SLA shall be applied to the cabin weight.

Light Ship: The boat is complete in all respects including all outfit and ready for service with liquids in machinery at operating levels, but no personnel, fuel, or other variable loads.

Minimum Payload Capacity: Boat shall be capable of supporting a minimum of 2,260 lbs total payload, including personnel and mission gear. The notional breakdown of payload is 8 personnel at 220 lbs each and 500 lbs of mission gear. Mission gear is defined as a combination of miscellaneous mission gear and cargo tied down on the deck.

Full Load Condition: Light Ship plus Minimum Payload, full fuel, and SLA. Diesel fuel weight shall be calculated using a density of 7.1 lbs/gallon.

Min Op Condition: Light Ship plus Minimum Payload less 5 personnel (220 lbs each) with 10% fuel. Diesel fuel weight shall be calculated using a density of 7.1 lbs/gallon.

PDIT (Pre-Delivery Inspection and Trials) Load Conditions:

o PDIT Load Condition 1: Same as Full Load Condition.

o PDIT Load Condition 2: Same as Min Op Condition.

Boat Design Hoisting: Full Load less 8 personnel (220 lbs each).

Cabin Design Hoisting: Cabin is complete in all respects including all outfit and ready for service plus 200 lbs of SLA.

Hull Design Hoisting: Full Load less 8 personnel (220 lbs each) and Cabin Design Hoisting weight.

070-4 ABYC Standards

As a minimum, the boat in all respects shall meet American Boat and Yacht Council (ABYC) standards and recommended practices.

070-5 Alterations

Alterations to Original Equipment Manufacturers’ (OEM) products by the Contractor or distributor are highly discouraged. If alterations are necessary, documentation of the change shall be submitted for Government approval and shall be provided with the Technical Data Package (TDP).

070-6 Seakeeping, Dynamic Stability, and Maneuverability

The boat shall be able to operate safely in the specified environmental conditions and shall be safe and controllable at all speeds and under all loading conditions specified herein. Safe and controllable includes operation where boat orientation, motions, and accelerations do not pose a hazard to the crew or passengers that is not otherwise controllable by good seamanship and boat handling.

The boat shall be able to maintain a straight course in the forward direction in calm, flat conditions at all speeds and loading conditions. Without coxswain action for 10 seconds, the boat shall not deviate course by more than 5 degrees.

The astern performance shall be such that the boat can be maneuvered in reverse at speeds of up to 3 knots (minimum) in calm, flat conditions at all loading conditions. The boat shall be capable of performing backing turns to port and starboard.

070-7 Configuration Management

The contractor shall maintain configuration management of the boat per the SOW Section C.

070-8 Installation of Equipment, Machinery, and Materials

Components or part of equipment and machinery shall be new. Unless otherwise specified, OEM recommendations for design and installation of their products into the boat shall be followed.

Systems and components shall be selected for durability, longevity, safety, and ruggedness.

Components shall be selected to maximize the use of Commercial-Off-The-Shelf (COTS) products and to maximize commonality between hulls. Systems and components shall be installed with proper tools.

All systems shall be free from leaks and safety hazards. Equipment, components, wiring, and piping shall be supported clear of the bilge to the maximum extent practicable.

All piping shall be cleaned to a degree of cleanliness that results in a surface that is reasonably free of contamination and where any remaining residue on the surface does not interfere with system operation or damage system components.

Foundations and brackets for equipment shall be configured to provide access for cleaning, painting, preservation, and maintenance, and to prevent accumulation of water, dirt, and foreign material.

Connecting piping or hose and wiring shall be run to minimize exposure to weather. Bulkhead and deck penetrations shall be as close as practicable to the equipment being served, preferably by direct connection through the adjacent deck or bulkhead.

Systems, equipment, and components shall be installed to facilitate accessibility for operating efficiency and for inspection, adjustment, and repair. Permanent fittings and structure shall be kept clear of routes required for the removal of machinery and equipment. The space behind equipment may be inaccessible after installation; this factor shall be considered in providing proper preservation in way of such equipment and in selecting the location of pipes, ducts, wireways, and other permanent fittings behind such equipment. Nooks, cracks, and openings where water, dirt, dust, or foreign material can accumulate shall be avoided.

Protection of personnel against operating hazards shall be provided. Shafting, couplings, gears, flexible shafts, and similar items shall have adequate guards installed for protection of personnel.

Such protective guards shall be removable without dismantling the machinery surrounded.

Guards shall be as lightweight as is practical and consistent with required protection and strength.

Guards shall be of sufficient strength to be used as steps or hand holds if located where such use may be anticipated.

Protective guards or insulation shall be installed to prevent contact with equipment where surface temperatures exceed 200°F. If surfaces exceed 140°F in the proximity of controls or manual actuators requiring manipulation by personnel during normal operation, protective guards or insulation shall be installed to prevent contact. For other surfaces exceeding 140°F, caution signs shall be installed.

Protective guards shall also be installed as barriers to prevent personnel from inadvertently contacting energized and exposed electrical circuits, components, and terminals.

Equipment shall be protected against the hazard of personnel brushing against or being thrown against the equipment, particularly under heavy sea conditions, and inadvertently causing damage to exposed components or resulting in maladjustment of exposed functional controls such as push buttons, knobs, and switches. Protection shall be provided by equipment arrangement or design or by installation of enclosures, screens, or guard rails. All sharp edges exposed to personnel shall be dressed, ground or radiused to avoid injury to personnel.

071 ACCESS

071-1 Accessibility

Electrical and mechanical components shall be accessible for maintenance and repair. All items requiring operation or maintenance (e.g. switches, valves, filters, strainers, seacocks, bilge pumps, mufflers, etc.) shall be readily accessible while at the dock or underway. Stowage and securing of arches, antennas, masts or other items shall not prevent access to critical items such as battery switches, fuel shut off valves or other items that need to be checked, secured or operated, including any of the required transport modes.

071-2 Bilge Access

All bilges and voids shall have removable plates or hatches for bilge access and inspection. The access and inspection openings shall be of sufficient size and locations to allow personnel visual access to the entire bilge and void areas.

073 NOISE, VIBRATION, AND RESILIENT MOUNTINGS

073-1 Noise Levels (Exterior)

Noise levels on the aft deck shall not exceed 84 dBA during all operating conditions.

See Section 092 for certification requirements

073-2 Noise Levels (Interior)

Noise levels inside the cabin shall not exceed 84 dBA during all operating conditions. Insulation shall be provided as required to achieve required noise levels.

The engine room shall be equipped with appropriate noise warning signs advising personnel of the noise hazard and the need for hearing protection (Section 602).

073-3 Resilient Mounts

Mounts for removable components and accessories subject to vibration, including items moved for towing or transport, shall be provided with resilient material as necessary to prevent rattling.

074 WELDING AND ALLIED PROCESSES

074-1 General

Welder and weld procedure qualification – weld procedures and welder qualification, including the associated record keeping requirements, shall be in accordance with American Bureau of Shipping (ABS), American Society of Mechanical Engineers (ASME), American Welding Society (AWS), NAVSEA TO300-AU-SPN-010A dated 5 October, 1992 (NAVSEA SPN-10) or NAVSEA 0900-

LP-060-4010 (NAVSEA 4010).

The Contractor shall select one of these welding codes and adhere to all requirements of the selected document for each welding procedure specification. The Contractor may select different regulating codes for different weld procedures; however, all documentation, welding and welder requirements for each procedure (for example the Welding Procedure Specifications (WPSs), the Procedure Qualification Records (PQRs) and the welder qualification and testing of the welds) must follow the same code.

All documentation pertaining to welder and weld procedure qualification shall be maintained by the Contractor and shall be available for inspection by the Government.

074-2 Visual Inspections

All welds shall be visually inspected.

Welds shall be free of slag, weld splatter, cracks, sharp irregularities, craters and incomplete fusion.

The weld edge shall not form a reentrant angle with the base metal less than 90 degrees due to lack of fusion, undercut or excessive convexity.

Fillet welds dimensioned 3/8 inch or less shall not vary below the specified size by more than 1/16 inch for a total distance greater than 25 percent of the joint length. Fillet welds dimensioned 7/16 inch and larger shall not be less than the specified size. Fillet welds in excess of the required dimensions shall be avoided; however, oversized welds will be acceptable provided they meet the contour requirements and do not interfere with proper operation of the boat or its components. Fillet weld root openings shall not be greater than 1/16 inch.

Undercut shall not reduce the base metal thickness by more than 1/32 inch.

Welds shall not exhibit porosity or worm holes in excess of two indications 1/16 inch or larger in any 6 inch length of weld, exclusive of weld crater porosity.

Grinding to correct the weld profile shall not reduce the base metal thickness by more than 1/32 inch.

074-3 Dye Penetrant Testing (PT)

Cabin hoisting fittings are aluminum critical welded assemblies. Aluminum critical welded assemblies shall be visually inspected and PT tested per Section 092 as follows:

1. Visually inspect completed critical welded assembly per Section 074-2. If passing, proceed to step 2.

2. Before load testing, PT welds and 1/2 inch of base metal on either side of the weld for linear indications greater than 1/16 inch. If passing, proceed to step 3.

3. Pull test the installed assembly to the load per Section 092.

4. After load testing, PT welds and 1/2 inch of base metal on either side of the weld for linear indications greater than 1/16 inch. If passing proceed to step 5.

5. Visual inspection of fittings and boat structure for signs of failure or permanent deformation.

074-4 Radiographic Testing (RT) and Ultrasonic Testing (UT)

The forward and aft towing bitts, shoulder and quarter H-bitts, chocks, winch foundations, self-aligning roller chocks, winch deck padeyes, and boat hoisting fittings are steel critical welded assemblies. Steel critical welded assemblies shall be visually inspected and RT or UT per Section 092.

Inspection and non-destructive test requirements for production welds shall be as specified in NAVSEA 4010, Section 6. UT shall be considered an equivalent substitute to RT in meeting the non-destructive test requirements of NAVSEA 4010.

Acceptance criteria for production welds shall be as specified in NAVSEA 4010, Section 8, except for UT acceptance criteria which shall be in accordance with MIL-STD-2035A.

Acceptance criteria for distortion shall be as specified in NAVSEA 4010, Section 12.

075 FASTENERS

075-1 Stainless Steel Fasteners

Fasteners throughout shall be type 316 Stainless Steel (UNS S31600). Fasteners used for structural applications shall be ASTM F593, Alloy Group 2 (type 316 stainless steel), Condition A or CW.

For bolts with high strength requirements, non-stainless steel bolts may be used with Government approval.

Self-locking hardware shall be used unless otherwise specified. Component mounting shall be through-bolted with ASTM F594 (type 316 stainless steel) nylon insert lock nuts and flat washers wherever practicable to suit fastener reinstallation during maintenance and repair. Threaded fasteners shall fully engage nuts with one to five threads protruding. Excessive thread protrusion that poses personnel hazard shall be avoided. Fasteners may be threaded into structural or non-structural materials only with Government approval.

Any pins used for folding, removable, or stowable features shall be secured with stainless steel lanyard to prevent loss. Pin handles may be aluminum. Spring loaded ball bearing type pins shall not be used.

078 MATERIALS

Components or parts of equipment and machinery shall be new. When materials are referred to in this Specification without further identification, they shall be as specified in this section. Other materials for specific applications are defined in the specific sections of this Specification, or on the drawings or referenced documents that require their use.

No plastic (without explicit Government approval), high density polyethylene (HDPE), polyvinyl chloride (PVC) or Chlorinated polyvinyl chloride (CPVC) shall be used except OEM components (e.g. electric bilge pump, National Electrical Manufacturers Association (NEMA) Boxes).

078-1 Structural Material

Except as otherwise specified or approved by the Government, structural steel materials shall conform to the following specifications:

Cast: ASTM A27, Grade 60 30, Class 1

Forgings: ASTM A668, Class B

Plate, shapes and bars: ASTM A36 or ABS Hull A

Sheet: ASTM A607 or ABS Hull A

Pipe: ASTM A53, types E or S, grade B or ASTM A106, grade B

Tubing: ASTM A500, Grade B or ASTM A501

Except as otherwise specified or approved by the Government, structural aluminum materials shall be used and conform to the following specifications:

Sand cast: 3560 T6

Plate and sheet: 5086 H116 or 5086-H117 both ASTM B928

Extrusions: 5086 H111; for non welded applications 6061 T6 or 6061 T52 may be substituted.

Drawn tube: 5086 H32; for non welded applications 6061 T6 may be substituted.

Non-structural components such as handrails, small component brackets, and wire ways may include extruded 6061 materials. Non-structural 6061 components in welded applications shall be approved by the Government prior to fabrication.

Stainless Steel (if used) shall be:

Cast for general applications: J92800 or J92500; for non-welded applications UNS J92900 or J92600 may be substituted.

Cast for underwater applications: J92800; for non-welded applications UNS J92900 may be substituted.

Plate, sheet, bars, shapes, tubing, pipe: S31603; for non-welded applications S31600 may be substituted.

078-2 Piping System Materials

When materials for piping systems are referred to in this Specification without further identification, they shall be as specified in this section. Other materials for specific applications are defined in the specific sections of this Specification, or referenced documents that require their use.

Valves, strainers, and fittings shall be stainless steel or bronze as specified:

Stainless Steel: Grade F 316, UNS S31600 – ASTM A182; or Type 316, UNS S31600 – ASTM A276; or Grade TP316, UNS S31600 – ASTM A312; or Grade CF8M, UNS J92900

– ASTM A351,

Bronze: UNS C92200 – ASTM B61; or UNS C83600 – ASTM B62; or UNS C84400 –

ASTM B584.

Piping and tubing shall be stainless steel, copper, or copper-nickel (CuNi) as specified:

Stainless Steel: Grade TP316 or TP316L, UNS S31600 or S31603 – ASTM A312 or

ASTM A213

Copper-Nickel (CuNi): seamless Pipe and Tube: ASTM B466; or Welded Pipe: ASTM B467.

078-3 Corrosion Control

All parts and fittings required for disassembly of systems shall be of Monel, stainless steel type 316L (or 316 if not welded), or copper alloy containing no more than 10% zinc (except manganese bronze), whichever is compatible with the basic material of the equipment. Stainless steel type 316L shall be used where it is likely to be submerged in seawater.

Components using ferrous metals other than stainless steel shall not be used except where specifically required by this Specification or with prior Government approval. Where ferrous metals other than stainless steel are required by this Specification, they shall be hot-dip galvanized or coated (zinc plating and electro-galvanizing is not be considered an acceptable coating). The protective coating shall be applied after fabrication. Alternatively, ferrous metal items may be replaced with stainless steel items, or items of other non-corroding materials.

Boat mechanical components and subcomponents shall be suitable for a marine environment (corrosion resistant). Joined components shall be galvanically compatible with each other wherever possible, or shall be isolated to prevent galvanic corrosion. Components not available in a corrosion resistant material shall be protected or coated to reduce or eliminate corrosion (e.g. paint, corrosion inhibitor, etc.).

Where it is necessary to join dissimilar metals, faying surfaces of the galvanically dissimilar metals shall be electrically isolated including fasteners, using non-water absorbent dielectric barrier(s), (e.g. gaskets, washers, sleeves, bushings, pipe or hose hangers, etc.), and hose of insulating material.

In order to exclude moisture from the joint, faying surfaces between mechanically fastened metal components, except machinery foundation shims, shall be protected by the use of bedding compound or gaskets, as applicable. Unless otherwise specified, gaskets for mechanically attached fitting shall be neoprene.

See Section 633 for cathodic protection requirements.

Use U.S. Navy Craft Mechanical Practices NSWCCD-23-TM-2011/05 for guidance.

078-4 Bedding Compound

Bedding compound shall be highly elastic, non-corrosive, paintable, solvent-free, with high adhesion properties and be suitable to the intended environment.

Polysulfide and polyurethane sealants may be used above and below the waterline. Where waterproof adhesive bonds are required, a polyurethane compound shall be used.

078-5 Non-Biodegradable Materials

Use of wood and other hygroscopic or biodegradable materials anywhere on the boat is prohibited.

All materials shall be marine grade and resistant to corrosion and Ultraviolet (UV) exposure.

078-6 Fabric Material

All boat fabric shall be marine grade as well as fade-, stain- and mildew-resistant and a near match in color as the surface it is mounted to or covering unless otherwise noted. Fabrics shall be easy to maintain and waterproof and/or breathable where required. All seams, edges, grommets, fastening points and areas of chafe shall be reinforced. Venting is acceptable to ventilate covers, but must minimize or eliminate the intrusion of water. Seats, seat fabric and foam shall be durable, provide comfort and be flame retardant. Foam shall not retain or absorb water.

078-7 Fire Retardant Interior Materials

Unless otherwise specified, all interior materials shall be fire retardant.

Thermal and acoustic insulating materials, with the exception of mass barriers, (Section 635) shall be non-combustible in accordance with 46 CFR Part 164.109.

079 STABILITY

079-1 Intact Stability

Stability shall meet NAVSEACOMBATSYSENGSTA Report No. 6660-99 Rev. A, Procedures Manual for Stability Analysis of U.S. Navy Small Craft for intact stability in the Full Load and Min Op conditions for:

Beam winds combined with rolling for Harbor Service (wind speed of 60 knots at 10m height).

Lifting heavy weights over the side (see Section 589 for Davit requirements)

Crowding of passengers to one side

Topside icing (3 inch thickness)

In addition, the intact stability at the Full Load and Min Op conditions shall meet the requirements of ABS, Rules for Building and Classing Steel Vessels Under 90 Meters in Length, Part 5 Chapter 11 Appendix 1, Intact Stability Guidelines for Towing Vessels.

A VCG margin (increase to calculated VCG) of 0.3 ft shall be used for stability calculations.. Any gunwale tops, vents, or openings that allow water to enter into the cabin or below deck shall be used as the down flooding points. All windows, hatches, and openings in deck that do not meet ABYC H-3.7.3 test for watertight devices or structures shall be treated as potential down flooding points.

See Section 085 for technical analysis requirements.

084 TRANSPORTATION AND HANDLING

084-1 Road Transport

Boat, with cabin and upper portion of pusher knees removed, shall meet all requirements for road transport (wide load with restrictions) via low-boy trailer on Continental United States (CONUS) Highways. Maximum boat dimensions when disassembled for transport shall not exceed:

Beam: 15 ft (including installed fendering)

Height: 11 ft (measured from lowest appendage to highest fixed structure)

084-2 Maritime Transport

Boat shall be designed for marine transport in accordance with NSWCCD-23-TM-2009/64 Rev C, to include onboard stowage.

Boat shall be designed for maritime transport and logistical launch and recovery (e.g. crane, deck cargo) from decks of USN, Military Sealift Command (MSC), and commercial shipping.

084-3 Boat Tiedown Fittings

Boat shall have tiedown fittings incorporated into existing structure, e.g. towing bitts (Section 582), deck chocks (Section 582). Labeling of the fittings shall include load ratings of the fittings in lbs. Tiedown fitting and adjacent structure shall be sized for maximum applicable load, as follows:

1. OTR Transport: Restraint of boat using Full load condition weight (see Section 070), shall be designed per MIL-STD-1366E Section 5.1.6 and 49 CFR Part 393.102, to provide a minimum safety factor of 1.5 on yield strength, or

2. Marine Transport: Restraint of boat using Full condition weight (see Section 070), per MIL-STD-1366E Section 5.1.6 shall provide a minimum safety factor of 1.5 on yield strength. Fittings’ design limit loads are as follow: 0.5 times the load in the longitudinal direction and 1.0 time the loads in the lateral direction. For calculations, bunk loads can be assumed to restrain the boat in the lateral direction.

See Sections 085 and 092 for technical analysis and testing requirements.

084-4 Water Proof Cover

An aluminum reusable water proof cover shall be provided for protection from the elements while the cabin is removed for transport, maintenance, or long term storage. Cover design shall prevent pooling of water and shall be vented.

085 TECHNICAL DATA PACKAGE (TDP)

The TDP shall include all information essential for acceptance, operation, training, maintenance, repair, modification and supply support for the delivered boat. The TDP shall include, but not be limited to:

1. Technical Design Analyses;

2. Construction (“As-built”) boat drawings including or cross referenced to:

3. a Bill of Materials (BOM) to the line replaceable unit (LRU) level;

4. COTS manuals;

5. Boat Technical Manual;

6. OEM certifications;

7. OEM warranty coverage for major systems;

8. Test and Trials Reports;

9. A Master Data Index.

085-1 Technical Design Analyses

Technical Design Analyses shall be clear…