Addendum One.pdf

COMMONWEALTH OF KENTUCKY

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

INVITATION TO BID NO: RFB-126-23

FOR: Mike Baker High Priority AML Project Letcher County, Kentucky

DATE: October 17, 2022

RFB-785-2300000220

ADDENDUM NO. One (1)

BIDDER SHALL CONFORM TO THE FOLLOWING CHANGES AS SAME SHALL BECOME BINDING

UPON THE CONTRACT TO BE ISSUED IN RESPONSE TO THIS INVITATION TO BID.

Item 1: Refer to addendum to be distributed by Lynn Imaging for all additions, deletions, and/or changes to specifications and/or drawings.

Item 2: Bidders must use Revised Unit Price Page in lieu of previously issued.

Item 3: Revised COR Documents

Item 4: Revised Engineers Estimate of Quantities Page

Item 5: Revised Plans

END OF ADDENDUM

Invitation to Bid No. RFB-126-23 For: Mike Baker High Priority AML Project Letcher County, Kentucky

Susan Ward, Statewide Procurement Analyst II Division of Engineering and Contract Administration

22AML017 - MIKE BAKER DRAINAGE HP (AML) RECLAMATION PROJECT

LETCHER COUNTY, KENTUCKY

ENGINEER'S ESTIMATE rev. 1

NO. ITEM QUANTITY UNIT

1 MOBILIZATION 1.0 L.S.

2 *UTILITY RELOCATION/REPLACEMENT 1.0 A.C.U.

3 TRAFFIC CONTROL 1.0 L.S.

4 *STRUCTURE REMOVAL/REPLACEMENT 1.0 A.C.U.

5 SITE PREPARATION 0.5 ACRE

6 SILT BARRIER - BALES & FENCE 250.0 LF

7 PIPE CLEANOUT / RE-INSTALL 160.0 LF

8 EARTHWORK (LUMP SUM) 1.0 L.S.

9 DROP BOX- CONCRETE 2.0 EACH

10 CONCRETE HEADWALL- PIPES ≤36" DIA. 1.0 EACH

11 RESIDENTIAL SEEDING 0.5 ACRE

12 DENSE GRADE AGGREGATE 200.0 TON

13 ROADWAY STONE 50.0 TON

NOTE: THE AUTHENTICATION OF BID AND STATEMENT OF NON-

COLLUSION AND NON-CONFLICT OF INTEREST PAGE MUST BE

PROPERLY EXECUTED FOR THE TOTAL BID AMOUNT TO BE VALID.

* Allowances included in the Contract Amount: The Contractor is required by Article ’30 of the General Conditions to include in the Contract Amount the following Allowances:

*UTILITY RELOCATION/REPLACEMENT $ 2,500.00

*LANDSCAPE ALLOWANCE $ -

*STRUCTURE REMOVAL/REPLACEMENT $ 1,000.00

*PLEASE NOTE: ALLOWANCE DOLLAR AMOUNTS STATED ABOVE MUST

BE THE EQUILVALENT DOLLAR AMOUNTS INCLUDED ON THE

SCHEDULE OF VALUES AS SUBMITTED BY THE CONTRACTOR.

*Allowances shall include all necessary materials, costs of delivery, installation labor, tools and equipment necessary to provide the item or services indicated in the Allowance. When the item of work or service is completed, the Contact Amount is modified by Change Order to reconcile the Allowance with the actual cost of the item or service provided. The contractor’s overhead, profit, insurance and bonds, and administrative costs are included in the prescribed markup permitted by Article ’14 of the General Conditions “Changes in the Work” and are not to be included in the Allowance.

Revised 2/2/2021

COR & BID & BMP 1

22AML017 MIKE BAKER DRAINAGE HP (AML) RECLAMATION PROJECT rev1

A. STANDARD DOCUMENTS

The AML Standard Details, Technical Specifications, and Bid Item Descriptions are posted on the Division’s website at https://eec.ky.gov/Natural-Resources/Mining/Abandoned-Mine- Lands/Pages/Standard_Details.aspx.

B. INCREASE AND/OR DECREASE OF QUANTITIES

The Contractor is required at time of submitting a bid proposal for this work to provide specific Unit Prices that will be used to add or deduct those specific work items or services by an established unit of measure and the stated price per unit. Unit prices include all necessary materials, costs of delivery, installation labor, tools and equipment necessary to provide the unit measured item. If a unit price is used in a change to the work by Change Order, the contractor’s overhead, profit, insurance and bonds, and administrative costs are included in the prescribed markup permitted by Article ’14 of the General Conditions “Changes in the Work” and are not to be included in the unit price. For a schedule of Unit Prices see the “Unit Prices” section of the Official Bid Document.

C. CONTRACT LENGTH

All work shall be completed within FORTY FIVE (45) calendar days from the effective date of the Award of Contract. Within the bounds of prudent project performance, it shall be the responsibility of the CONTRACTOR to plan and implement construction sequences which follow the intent of these CONTRACT DOCUMENTS, particularly as, reflected in the Drawings and Special Conditions and to protect any portion of the contract which may be completed before others.

D. CONTRACTOR’S INFORMATION SHEET

The AML CONTRACTOR/SUBCONTRACTOR INFORMATION FORM sheet must be filled out and submitted with the bid. Failure to submit the AML Contractor/SubContractor Information Form sheet with the bid will be the basis for declaring the bid “Non-Responsive”

E. SPECIAL CONDITIONS & PROJECT NOTES

- On occasion, a property owner may require a CONTRACTOR to add them on their General Liability and/or Automobile Insurance as an “Additional Insured.” AML will inform the CONTRACTOR when this requirement is being made by the property owner. In these cases, the CONTRACTOR must submit to AML copies of their certificate of insurance documenting the “Additional Insured” before they will be allowed to mobilize equipment and forces on to said properties. Any fees, rate increases, or other costs incurred by the CONTRACTOR for this requirement, if any, will be considered incidental to mobilization and as such no compensation will be made by AML. The “Additional Insured” must remain on the CONTRACTOR’s policy(s) for the full length of the contract.

COR & BID & BMP 2

- Add any special conditions, notes, exceptions to standard documents or write “None”.

- Add Bid Item descriptions that are contrary to standards notes.

F. PERMITS & FEES – AML will be responsible for obtaining any permits that are checked below.

(check all that apply)

☐KYTC Encroachment Permit

☐KY DOW Water Permits

☐USACE Permit

The CONTRACTOR is responsible for all other permits and/or fees necessary to begin the project. The CONTRACTOR is advised that on occasion, other permits and/or fees may be required by federal, state, and local government(s). Other types of permits and/or fees are not the responsibility of AML and as such, these will be the complete and total responsibility of the CONTRACTOR to obtain. These must be obtained before AML will allow mobilization of equipment and forces on to said properties. All costs associated with other permits or fees will be the responsibility of the CONTRACTOR. Please refer to “General Provisions” in the AML Technical Specifications.

COR & BID & BMP 3

BID ITEM DESCRIPTION

22AML017 MIKE BAKER DRAINAGE HP AML RECLAMATION PROJECT

NO ITEM DESCRIPTION

1. MOBILIZATION This item consists of the mobilization and demobilization of the CONTRACTOR’S forces and equipment in accordance with the “Mobilization/Demobilization” AML Standard Technical Specification. The amount of this bid item is not to exceed 5 percent of the sum of the lump sum bid price.

Measurement: Not Applicable.

2. UTILITY

RELOCATION /

REPLACEMENT

This consists of furnishing all materials, equipment, and labor necessary to replace utilities damaged by construction or relocate any utilities that are in the construction area in accordance with the “Utility Relocation” AML Standard Technical Specification. The CONTRACTOR is required to supply the ENGINEER with all documentation to support cost incurred to qualify for reimbursement.

Special Considerations: None Major Incidentals: These will be listed in writing by the ENGINEER prior to beginning the work.

3. TRAFFIC CONTROL This item consists of maintaining and controlling traffic on existing roads

(public and private) affected by this project as depicted on the Drawings and as directed by the ENGINEER in accordance with the “Traffic Control” AML Standard Technical Specification. Appropriate signs shall be erected at the project limits and flag persons shall be used as needed.

Special Considerations: None Major Incidentals: Signs, flaggers, steel plates, immediately clearing debris from roadway.

COR & BID & BMP 4

4. STRUCTURE

REMOVAL/

REPLACEMENT

This item represents the ENGINEER'S best estimate of removal/replacement cost of designated qualifying structural features “in kind” to facilitate normal construction activities as depicted on the Drawings and as directed by the ENGINEER in accordance with the “Structure Removal / Replacement” AML Standard Technical Specification. The CONTRACTOR is required to supply the ENGINEER with all documentation to support cost incurred to qualify for reimbursement.

Special Considerations: None Inspector Notes: Inventory of structures, pictures, and dimensions, before construction starts. Any structures that are removed shall be accompanied by pictures.

Major Incidentals: These will be listed in writing by the ENGINEER prior to beginning the work.

Measurement: None

5. SITE PREPARATION This item of work shall consist of furnishing all materials, equipment, and labor as depicted on the Drawings and as directed by the ENGINEER in accordance with the “Site Preparation” AML Standard Technical Specification.

Special Considerations: None Major Incidentals: Clearing, grubbing, windrowing, burning, pipe removal and disposal, pipe cleanout, temporary diversion ditch construction, domestic debris removal and disposal, concrete & bituminous asphalt debris removal and disposal, access improvement/construction, in-kind fence repair/replacement, and temporary stream diversion.

Measurement: Actual Quantities shall be measured with a handheld GPS and rounded up to the next whole 0.5 acre actually cleared and grubbed (excludes slurry and refuse areas.

6. SILT BARRIER–

BALES & FENCE

This item consists of furnishing all materials, equipment, and labor necessary to maintain silt control as depicted on the Drawings, AML Standard Details, and as directed by the ENGINEER in accordance with the “Silt Control” AML Standard Technical Specification. Hay/straw bales shall be placed with an overlap equal to 0.4 bales per linear foot of silt control fencing. Silt fence shall be trenched and removed at the end of the project. Failure to remove silt control fence (geotextile fabrics) shall result in forfeiture of demobilization.

Special Considerations: None Major Incidentals: Maintenance, silt fence trenching and removal Measurement: Actual Quantities shall be measured as the next whole linear foot installed and accepted by the ENGINEER.

COR & BID & BMP 5

7. PIPE CLEANOUT /

RE-INSTALL

This item shall consist of furnishing all materials, equipment, and labor for completely extracting all sediment / rock deposited in the existing HDPE pipe. All rock and sediment removed from the pipe shall be transported to the waste and graded as called for in the EARTHWORK BID ITEM.

Special Considerations: ANY RE-INSTALL IS CONSIDERED

INCIDENTAL

Measurement: Actual Quantities shall be measured as next whole linear foot FOR PIPE COMPLETELY CLEARED OF ALL DEBRIS and accepted by the

ENGINEER.

8. EARTHWORK

(LUMP SUM)

This item consist of furnishing all materials, equipment, and labor necessary for excavation of materials as required, and to remove all of the rock / sediment deposited in the project, and transport it the off-site waste area. It shall be placed and graded at the waste area as directed by the ENGINEER in accordance with the “Earthwork” AML Standard Technical Specification.

Special Considerations: None Major Incidentals: Excavation, transportation, placement, compaction of all excavated materials including rock ditches constructed without hoe ram.

Measurement: Not applicable.

9. DROP BOX-

CONCRETE

This item consists of furnishing all materials, equipment, and labor, necessary to construct concrete drop boxes as depicted on the Drawings, AML Standard Details, and as directed by the ENGINEER in accordance with the “Drop / Junction Boxes” AML Standard Technical Specifications up to a depth of 8’.

Special Considerations: None Major Incidentals: Concrete, steel reinforcement, grout, formwork, aggregate backfill Measurement: Actual Quantities shall be measured as “EACH” unit installed and accepted by the ENGINEER.

10. CONCRETE

HEADWALL- PIPES

≤36” DIA.

This item consists of furnishing all materials, equipment, and labor, necessary to construct the headwalls as depicted on the Drawings, AML Standard Details, and as directed by the ENGINEER in accordance with the “Concrete Headwalls” AML Standard Technical Specification. Units cast in the field require fiber, pre-cast units require manufacturer certification that concrete meets or exceeds required strength.

Special Considerations: None Inspector Notes: For pre-cast units collect manufacturer certificate (includes strength of concrete used).

Major Incidentals: Concrete, steel reinforcement, fiber, grout, formwork, dissipaters, backfill Measurement: Actual Quantities shall be measured as “EACH” unit installed and accepted by the ENGINEER.

COR & BID & BMP 6

11. RESIDENTIAL

SEEDING

This item shall consist of furnishing all materials, equipment, and labor for the purpose of revegetation of the disturbed areas as depicted on the Drawings and as directed by the ENGINEER in accordance with the “Revegetation” AML Standard Technical Specification.

Special Considerations: None Major Incidentals: Seedbed preparation, agriculture limestone, fertilizer, seed, and mulch Measurement: Actual Quantities shall be measurement as the next tenth of an acre seeded as approved by the ENGINEER.

12. DENSE GRADE

AGGREGATE

This item shall consist of furnishing all materials, equipment, and labor necessary to place, and compact dense grade aggregate (DGA) as depicted on the Drawings and as directed by the ENGINEER in accordance with “Crushed Aggregate and Channel Lining” AML Standard Technical Specification.

Special Considerations: This item is for temporary paved roadway repairs and base preparation prior to bituminous repair. DGA USED for pipe RE-

INSTALLATION WILL BE PART OF THIS BID ITEM

Measurement: Actual Quantities shall be measured based on weigh tickets supplied to the ENGINEER as ton(s) of aggregate installed and accepted by the

ENGINEER.

13. ROADWAY STONE This item shall consist furnishing all materials, equipment, and labor necessary to place and compact as necessary the various gradations of stone as depicted on the Drawings and as directed by the ENGINEER in accordance with the “Crushed Aggregate and Channel Lining” AML Standard Technical Specification.

Special Considerations: None Measurement: Actual Quantities shall be measured based on weigh tickets supplied to the ENGINEER as ton(s) of each type of channel lining, and/or aggregate installed and accepted by the ENGINEER.

Erosion and Sediment Control Best Management Practices (BMP) Plan

COR & BID & BMP 7

January 2017

COR & BID & BMP 8

OVERVIEW

This Best Management Practices (BMP) plan is a guide for Kentucky Division of Abandoned Mine Lands (DAML) projects. It contains information regarding preventing, reducing and controlling erosion, sediment, and pollutant runoff from Abandoned Mine Land (AML) Reclamation and Acid Mine Drainage (AMD) Abatement project construction sites. The information in this BMP will aid DAML staff and contractors in selecting, installing, and maintaining erosion prevention and sediment control measures during the different stages of construction. This BMP plan, in accordance with DAML Technical Specifications and Standard Drawings, is intended to protect Kentucky’s streams from potential water quality impacts resulting from DAML projects.

This general BMP document is to outline the various pollution prevention measures used on AML Reclamation or AMD Abatement Projects. The primary sources of pollutants are solids mobilized during storm events and precipitants from mineralized mine drainage. Other sources of pollutants include oil/fuel/grease from servicing and operating construction equipment, concrete washout water, sanitary wastes, and trash/debris.

EROSION PREVENTION AND SEDIMENT CONTROL MEASURES

Plans for Reclamation and AMD abatement construction projects will include erosion control measures on the planview sheets when possible, and will depict Disturbed Drainage Areas (DDAs) and related information. The construction notes and project description may describe other control measures. The Contractor and Engineer may select an additional BMP for the project as the project changes and construction progresses. Projects that do not have DDAs annotated in the plans will employ the same concepts selecting and implementing this general BMP plan.

Address disturbed areas or sources of sediments by the most effective means in the specific work area. Direct non-storm water discharges to sediment basins/traps or to a filter fence enclosure in a flat vegetated infiltration area or filtered via another approved commercial product. All deep mine and surface impoundment water will be tested and treated, when as necessary, to meet the DAML Water-Treatment and Disposal Technical Specification unless stricter limitations are listed in an existing Total Daily Maximum Load (TMDL) limit.

PERMITS

The DAML shall review each project during project development to determine whether any permits are required to implement the project work. When a permit is required, DAML will make every effort to obtain the permit prior to letting the project for bidding. Permit specific conditions shall trump any standard conditions and/or practices. All permits must be maintained onsite and produced when requested by regulatory authorizes inducing representative of the permitting authority.

Common permits types for DAML projects:

COR & BID & BMP 9

401 Water Quality Certification (WQC) o Issued by the KY Division of Water

402 KY Pollution Discharge Elimination System (KPDES) o DAML activities are covered under the AML KPDES General Permit

404 US Army Corps of Engineers (USACE) o Issued by the US Army Corps of Engineers- Nashville District, Louisville District, or Huntington District (Depending upon major drainage basin) KY Stream Construction (Floodplain) o Issued by the KY Division of Water Local Floodplain Permit o Issued by the County/Municipality Local Storm Water Construction o Issued by the County/Municipality

A) Field Review Walk-Thru:

The DAML will conduct a project review between the Project Engineer, Construction Branch Personnel, Project Design Technician, and Field Office Staff, to review the construction plans and identify any changes needed prior to letting the project for bidding. The group will evaluate the locations and types of site specific BMP and any other erosion prevention and sediment control measures chosen for incorporation into the final design plans.

B) Pre-Bid Conference

DAML will present the project specific BMP and permit requirements/conditions to the potential contractors during the pre-bid conference meeting.

C) Pre-Construction Conference

Prior to the actual beginning of the project, DAML will hold a pre-construction conference between representatives of the DAML, the Contractor, including any Subcontractors, as well as other interested agencies and parties. Items discussed will include the time and sequence for construction, planned methods of operation, payment, and other relevant questions including any permit requirements and the erosion and sediment control plan.

D) Construction Access

This is the first land-disturbing activity. Construction entrances shall be a minimum of twenty

(20) feet wide by fifty (50) feet long, measured from the shoulder of the public road, and consist of No. 2 aggregate over a heavy weight non-woven filter fabric base. As soon as construction begins, stabilize bare areas with gravel and temporary mulch and/or vegetation.

E) Clearing and Grubbing

Use the following techniques for clearing and grubbing activities:

COR & BID & BMP 10

1) Leave areas undisturbed when possible.

2) Construct silt basins to provide silt volume for large areas.

3) Construct Silt Trap(s) Type A for small areas.

4) Construct Type B silt traps for areas with rapid runoff and sediment-laden runoff.

5) All silt traps should have a 3:1 flow length to width ratio. Add spreader bars, baffles, or turbidity curtains to maintain the flow path ratio when site conditions require traps sizes smaller than the standard detail dimensions.

6) Install geotextile bags and/or rock checks in front of existing drop inlets.

7) Construct diversion ditches to catch sheet runoff and carry it to basins or traps or to divert it around areas to be disturbed.

8) Maintain brush and/or other barriers to slow and/or divert runoff.

9) Construct silt fences/hay bales to catch sheet runoff on short slopes. For longer slopes, multiple rows of silt fence/hay bales may be considered.

10) Apply temporarily mulch to area not actively being disturbed or for any area left undisturbed for fourteen (14) days.

11) Employ non-standard or innovative methods.

F) Stream Crossings / Work Along Streams

1) Temporary low-water stream crossings follow the guidelines included in the DAML

Technical Specifications and those established by the KY Division of Water Floodplain Management Section. Removal of a temporary crossing may be required to accommodate large storm events.

2) Do not completely block stream flow (even temporary). Instead, utilize some form of pass thru mechanism during all AML projects.

3) Work within a stream channel shall not cause flooding of properties upstream, downstream or within the project area or cause downstream water quality degradation. Minimize equipment contact time with the stream water by diverting water around equipment working in or along streams.

4) No flowing water will interact with any uncured concrete placed in the stream channel.

5) Divert all stream water around the work areas in accordance to methods listed in the DAML

Stream Protection & Relocation technical specification, AML Standard Details Section 60, and as by the appropriate permit guidelines.

6) Temporary out of channel stream diversion must use one of the three approved methods:

pipe diversion, sandbag/stone channel diversion, and/or fabric-based channel diversion.

Do not construct any temporarily diverted channel on bare, erodible soil. No temporary diversion shall be permanent without a 401, 404, and other appropriate permits.

COR & BID & BMP 11

G) Deep Mine and Surface Water Impoundments

The DAML Resident Inspector will test the mine water from deep mines and surface impoundments on the project area to determine the pH and total iron content. Treat the water until it meets the DAML Water-Treatment and Disposal Technical Specification or an existing TMDL, whichever is stricter, before release through a silt control structure(s).

Monitoring & Recording

The DAML Inspector will maintain a log of the pH and total iron content results prior to releasing and during each release day. Perform a minimum of two (2) tests downstream each day to ensure the maintenance of water quality during release and is not degrading the receiving stream.

Types of structures/facilities include:

1) Silt Traps Type A (20’L x 5’W x 2’D min dugout)

2) Silt Traps Type B (20’L x 5’W x 2’D min dugout with rock berm)

3) Silt Check - Rock checks with filter fabric core lining installed in channels and in front of pipes

4) Temporary silt control fence with Class II filter berm

5) Sediment collection bags

H) Cut and Fill and Placement of Drainage Structures

Areas at final grade will be seeded and mulched within five (5) days. Soil stock piles and areas that are not at final grade but where construction will cease for a period of fourteen (14) days or longer, shall receive temporary mulch no later than fourteen (14) days from the last construction activity in that area.

Types of structures/facilities include:

1) Silt Traps Type B (20’L x 5’W x 2’D min dugout with rock berm)

2) Silt Checks - Bags in front of pipes after they are placed

3) Channel lining

4) Erosion control blanket

5) Temporary mulch and/or seeding for areas where construction activities will be ceased for

14 days or more

6) Non-standard or innovative methods

I) Temporary Shutdown

Items to be completed prior to shutdown include:

1) Clean out behind, repair or replace silt fence and/or hay bales

2) Clean out all silt traps

COR & BID & BMP 12

3) Apply temporary mulch and track into the soil

4) Sow cover crop (weather permitting)

J) Finish Work

1) Establish permanent seeding and protection

2) Remove non-permanent silt checks from ditches and drains if protected with other BMPs sufficient to control erosion and vegetation is established.

3) Remove non-permanent silt traps and basins.

4) Remove geotextile silt fence.

5) Planting trees and/or shrubs where they are included in the project.

6) Clean out behind, repair, and/or replace bale silt barriers

7) Clean out all permanent silt traps and basins

K) Post-Construction

The Contractor shall assume responsibility for all workmanship and materials for a period of one year from the date of final payment, as directed by the Contract Documents. Any work found to be defective due to failure to comply with the provisions and intent of the Contract Documents shall be corrected at the Contractor's expense. Problems determined not to be created by the landowner or due to the Contractor will be addressed by the DAML for a period of up to three years, pending available funding.

OTHER CONTROL MEASURES

L) Solid Materials

No solid materials, including rock and building materials, shall be discharged into waters of the U.S. except as authorized by the Clean Water Act (CWA) Section 401 and Section 404 permits.

M) Waste Materials

Collect and store waste materials that may leach pollutants (paint and paint containers, caulk tubes, oil/grease containers, liquids of any kind, soluble materials, etc.) in appropriate covered waste containers. Remove waste containers from the project site frequently as to not allow wastes to become a source of pollution. Instruct all personnel regarding the correct procedure for waste disposal and dispose of wastes in accordance with appropriate regulations.

N) Hazardous Waste

Manage and dispose of hazardous waste materials in the manner specified by local or state regulation. Notify the Resident Inspector if there are any hazardous wastes generated, and provide a plan for the management and disposal of such materials. Instruct site personnel with regard to proper storage and handling of hazardous wastes when required and use the practices to reduce the risks associated with all hazardous materials. Keep products in original containers

COR & BID & BMP 13

unless they are not re-sealable with the original labels and material safety data sheets (MSDS) will be reviewed and retained.

O) Spill Prevention

Use good housekeeping and material management practices to reduce the risk of spills or other exposure of materials and substances to the weather and/or runoff. Manufacturers' recommended methods for spill cleanup will be maintained on site and readily available upon request. Make personnel aware of procedures and the location of the information and cleanup supplies.

Equipment and materials will include as appropriate, brooms, dust pans, mops, rags, gloves, oil absorbents, sand, sawdust, and plastic and metal trash containers.

Clean up all spills immediately after discovery. Keep the spill area well ventilated. Personnel will wear appropriate protective clothing to prevent injury from contract with a hazardous substance. Report spills of toxic or hazardous material to the appropriate state/local agency as required by KRS 224 and applicable federal law. Wastes from spill cleanup will be disposed of in accordance with appropriate regulations. The spill prevention plan will be adjusted, as needed, to prevent spills from reoccurring and improve spill response and cleanup.

P) Petroleum Products

Monitor vehicles and equipment fueled and maintained on site for leaks, and receive regular preventative maintenance to reduce the chance of leakage. Protect petroleum products onsite will be stored in tightly sealed, clearly labeled containers from exposure to weather. The CONTRACTOR shall not have a total of over 1,300 gallons of petroleum products on site at any given time.

Q) Fertilizers

Store fertilizers in a covered area away from water. Transfer the contents of any partially used bag of fertilizer to a sealable plastic bin to avoid spills. Once applied, work into the soil and apply mulch to limit exposure to storm water.

R) Concrete Truck Washout

Concrete truck mixers and chutes will not be washed on pavement, near storm drain inlets, or within seventy (75) feet of any ditch, stream, wetland, lake, or sinkhole. Where possible, discharge excess concrete and wash water to areas prepared for pouring new concrete, flat areas to be paved that are away from ditches or drainage system features, or other locations that will not drain off site. Where this approach is not possible, excavate a shallow earthen washbasin away from ditches to receive the wash water.

INSPECTIONS

Use inspection and maintenance practices to maintain erosion and sediment controls:

COR & BID & BMP 14

1) The Contractor and DAML Resident Inspector will inspect all erosion prevention and sediment control measures at least once each week and following any rain of 0.1 inch or more.

2) The DAML Resident Inspector will record the silt control inspections by in their daily report.

3) Silt fences/hay bales will be inspected for bypassing, overtopping, undercutting, depth of sediment, tears, and to ensure attachment to secure posts.

4) Inspect silt traps and basins for depth of sediment, and built-up sediment and clean out when it reaches 50% of the design capacity and at the end of the job.

5) Inspect diversion dikes and berms and promptly repaired any breaches. Repair areas that are eroding or scouring and re-seeded / mulched as needed.

6) Inspect temporary and permanent seeding and mulching for bare spots, washouts, and healthy growth. Repair bare or eroded areas as needed.

7) Inspect all material storage and equipment servicing areas that involve the management of bulk liquids fuels and bulk solids weekly for conditions that represent a release or possible release of pollutants to the environment.

MAINTENANCE

Maintain all measures in good working order; initiate corrective actions within twenty-four (24) hours of being reported and completed with five (5) days, address critical failures immediately unless site conditions are too dangerous. Remove Built-up sediment from behind the silt fence/hay bales before it has reached halfway up the height of the fence.

ENFORCEMENT

At all times, representatives from DAML and enforcement agencies will have access to the project site. The ENGINEER reserves right to stop work until erosion prevention and sediment control problems are addressed to his/her satisfaction.

10-14-2022

AutoCAD SHX Text

COMMONWEALTH OF KENTUCKY

AutoCAD SHX Text Index of Sheets

AutoCAD SHX Text F:\Projects\AML\22AML017 (Mike Baker)\1 Design Phase\1 Drawings\Planset - Mike Baker HP.dwg

AutoCAD SHX Text

PLANVIEW W/ PHOTO PLANVIEW WASTE AREA

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

22AML017 - MIKE BAKER HP AML RECLAMATION PROJECT

AutoCAD SHX Text

LETCHER COUNTY, KENTUCKY

AutoCAD SHX Text

22AML017 - MIKE BAKER AML RECLAMATION PROJECT LETCHER COUNTY

AutoCAD SHX Text 10/14/2022 3:10:37 PM bob.jones bob.jonesbob.jones

AutoCAD SHX Text

DRIVING DIRECTIONS: LATITUDE: LONGITUDE: LONGITUDE: DIRECTIONS

AutoCAD SHX Text FINANCE AND ADMINISTRATION CABINET DEPARTMENT FOR FACILITIES & SUPPORT SERVICES DIVISION OF ENGINEERING & CONTRACT ADMINISTRATION FRANKFORT, KENTUCKY

AutoCAD SHX Text ENERGY AND ENVIRONMENT CABINET DEPARTMENT FOR NATURAL RESOURCES DIVISION OF ABANDONED MINE LANDS

AutoCAD SHX Text THE AML STANDARD DETAILS AND TECHNICAL SPECIFICATIONS ARE AVAILABLE ON OUR WEBSITE AT: WWW.AML.KY.GOV UNDER "STANDARD DETAILS AND SPECIFICATIONS". BY BIDDING ON THIS PROJECT THE UNDER "STANDARD DETAILS AND SPECIFICATIONS". BY BIDDING ON THIS PROJECT THE CONTRACTOR ACKNOWLEDGES THEY HAVE REVIEWED AND UNDERSTAND THE STANDARD DETAILS AND TECHNICAL SPECIFICATIONS AS THEY APPLY TO THIS PROJECT. UTILITY NOTE PRIOR TO ANY EXCAVATION OR THE PLACEMENT OF FILL, THE CONTRACTOR IS REQUIRED TO CALL “KENTUCKY KENTUCKY 811” TWO (2) BUSINESS DAYS PRIOR TO ANY EXCAVATION / EXCAVATION ACTIVITIES. IF THERE ARE UTILITIES TWO (2) BUSINESS DAYS PRIOR TO ANY EXCAVATION / EXCAVATION ACTIVITIES. IF THERE ARE UTILITIES IN THE WORK AREAS THAT ARE NOT MEMBERS OF “KENTUCKY 811”, EACH UTILITY HAS TO BE CONTACTED KENTUCKY 811”, EACH UTILITY HAS TO BE CONTACTED , EACH UTILITY HAS TO BE CONTACTED DIRECTLY TO HAVE THEIR FACILITIES MARKED. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO ABIDE BY THE "UTILITY RELOCATION" TECHNICAL SPECIFICATION AND SECTION 22.3 OF THE "GENERAL PROVISIONS" TECHNICAL SPECIFICATION. DEPICTION OF THE UTILITIES ON THE PLANS ARE APPROXIMATE AND MAY NOT INCLUDE ALL EXISTING UTILITIES.

AutoCAD SHX Text

WASTE AREA

AutoCAD SHX Text

SITE

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text F:\Projects\AML\22AML017 (Mike Baker)\1 Design Phase\1 Drawings\Planset - Mike Baker HP.dwg

AutoCAD SHX Text

COMMONWEALTH OF KENTUCKY

AutoCAD SHX Text

DRAWN BY

AutoCAD SHX Text

DATE

AutoCAD SHX Text

CHECKED BY

AutoCAD SHX Text

PLANVIEW

AutoCAD SHX Text

BJ

AutoCAD SHX Text

RDJ

AutoCAD SHX Text

22AML017 - MIKE BAKER SLIDE HP (AML) RECLAMATION PROJECT LETCHER COUNTY

AutoCAD SHX Text ENERGY AND ENVIRONMENT CABINET DEPARTMENT OF NATURAL RESOURCES DIVISION OF ABANDONED MINE LANDS FRANKFORT, KY

AutoCAD SHX Text

LETCHER

AutoCAD SHX Text

COUNTY OF

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

TOTAL SHEETS

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

SEPT 2022

AutoCAD SHX Text FINANCE & ADMINISTRATION CABINET DEPARTMENT FOR FACILITIES & SUPPORT SERVICES DIVISION OF ENGINEERING & CONTRACT ADMINISTRATION FRANKFORT, KY

AutoCAD SHX Text Ex. 30" Dia HDPE Pipe Clean Out Entire 160 ft length

AutoCAD SHX Text Install/Construct Concrete Headwall (AML 23-10-7)

AutoCAD SHX Text Install/Construct Concrete Dropbox Inlet KYTC TYPE 7 RDB-007-03

AutoCAD SHX Text Maintain Access

AutoCAD SHX Text Remove all sediment load from yard area and dispose of it in the waste area (0.5 Acres Total)

AutoCAD SHX Text Access to Site

AutoCAD SHX Text

HWY 805

AutoCAD SHX Text Ebb Wright Hollow Road

AutoCAD SHX Text Ex Bridge No Access Do Not Disturb

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text Janet Baker 606-855-4905

AutoCAD SHX Text Mike Wright 606-821-7800 Gerald Holbrook Bus. Partener

AutoCAD SHX Text 37°11'3.03"N 82°42'13.40"W

37°11'0.52"N 82°42'12.00"W

F:\Projects\AML\22AML017 (Mike Baker)\1 Design Phase\1 Drawings\Planset - Mike Baker HP.dwg

AutoCAD SHX Text

COMMONWEALTH OF KENTUCKY

AutoCAD SHX Text

DRAWN BY

AutoCAD SHX Text

DATE

AutoCAD SHX Text

CHECKED BY

AutoCAD SHX Text

PLANVIEW

AutoCAD SHX Text

BJ

AutoCAD SHX Text

RDJ

AutoCAD SHX Text

22AML017 - MIKE BAKER SLIDE HP (AML) RECLAMATION PROJECT LETCHER COUNTY

AutoCAD SHX Text ENERGY AND ENVIRONMENT CABINET DEPARTMENT OF NATURAL RESOURCES DIVISION OF ABANDONED MINE LANDS FRANKFORT, KY

AutoCAD SHX Text

LETCHER

AutoCAD SHX Text

COUNTY OF

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

TOTAL SHEETS

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

SEPT 2022

AutoCAD SHX Text FINANCE & ADMINISTRATION CABINET DEPARTMENT FOR FACILITIES & SUPPORT SERVICES DIVISION OF ENGINEERING & CONTRACT ADMINISTRATION FRANKFORT, KY

AutoCAD SHX Text

HWY 3410

AutoCAD SHX Text

MAYKING FD TONY FUGATE 606-633-2697

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

HWY 119

AutoCAD SHX Text PLACE WASTE MATERIAL NEAR BACK OF PROPERTY (PREVIOUSLY DISTURBED AREA) (0.5 Acre)

AutoCAD SHX Text

DOLLAR GENERAL STORE

AutoCAD SHX Text

TO SITE (6.0 MILES ONE-WAY)

AutoCAD SHX Text

HWY 119

AutoCAD SHX Text

TO WHITESBURG

AutoCAD SHX Text 37° 8'18.06"N 82°45'39.25"W

37° 8'17.76"N 82°45'32.68"W