A-A-55077B 11.26.19 - PGC17632 - Duffle Bag.pdf

INCH-POUND

A-A-55077B

26 November 2019

SUPERSEDING

A-A-55077A 05 January 2000

COMMERCIAL ITEM DESCRIPTION

BAG, DUFFEL

The General Services Administration has authorized the use of this commercial item description for all federal agencies.

1 SCOPE.

This document covers a nylon duck, Camouflage Green 483 (see paragraph 6.4) duffel bag measuring 12-1/2 inches in diameter by 37 inches deep, having one handle, one closing strap with snap hook, and shoulder straps. The modified commercial type bag is designed to hold individual clothing and equipage allowance and is intended for use by members of the Department of Defense.

2 SALIENT CHARACTERISTICS.

2.1 Description. The bag is tubular in shape, constructed with a sewn on bottom piece and open top with a single ply flap, attached to the body of the bag as shown in figure 2. The bag is closed by inserting a keeper through the grommets located around the top and can be securely locked with the attached closing strap with snap hook or a padlock if desired. The keeper is held in place by the turndown self-facing at the top of bag, as shown in figure 1. A webbing handle and shoulder straps are attached to provide means for either hand or shoulder carrying. The shoulder straps shall each have an adjuster and shall be padded: the pad shall finish approximately 2-1/4 inches wide and 14 inches in length and shall be covered with nylon duck cloth and stitched securely to the shoulder strap webbing. The handle and shoulder straps are reinforced with webbing stitched to the body of the bag. A pocket with a snap closure on the flap is attached to accommodate shipping documents.

2.2 Manufacturing requirements. The construction of the duffel bag shall conform in all respects to Figures 1-4 and shall be as specified herein. The body joining seam shall be ASTM-D6193 seam type LSc-2, stitch type 401; all other seams shall be stitch type 301. All thread ends that are visible on the item shall be trimmed to a length of not more than 1/4 inch. Cut ends of nylon webbing shall be seared smooth. Repairs such as mends, darns, patches, or splices are not permitted on the duffel bag. Location marks shall not be drilled. Printed location marks shall not be more than 1/32 inch in width. After completion, the finished bag shall be thoroughly cleaned, and all loose thread, lint, and foreign matter removed.

2.2.1 Attachment of grommets and fasteners. Holes punched to receive the grommets shall be smaller than the outside diameter of the grommet barrel so that the barrel must be forced through the hole. The grommets shall be securely clinched without cutting the materials. All grommet washers shall be on the outside of the bag. Roll of the clinched grommet shall not contain more than three scores (splits) and no scores (splits) shall exceed 1/16 inch in length. A hole shall be prepunched through the material before inserting the stud eyelet tube or the socket eyelet tube.

The hole shall be smaller than the outside diameter of the applicable eyelet tube, so that the tube must be forced through the hole. Prepunched holes shall not be accomplished by using stud or socket eyelet tubes (as applicable). The fastener components shall be securely clinched without cutting the surrounding material. Roll of the clinched eyelet of the assembled fastener component shall not possess more than three scores (splits). All grommets shall be reinforced with a piece of nylon duck measuring approximately 3 inches square, placed inside the turn-down facing. The grommets shall be placed as shown in figures 1 through 3, evenly spaced and approximately 12 inches apart.

2.2.2 Identification marking. The "US" marking shall be applied in the size and location indicated on figure 2, and shall be black in color, made by marking, direct printing, stamping, or stenciling. The identification marking shall be made up of characters approximately 1/4-inch in height, black in color, made by marking, direct printing, stamping, or stenciling on the inside of the top hem of the duffel bag. The marking legibility shall last the expected life of the bag. The identification marking shall include the following information:

Item Description:

Contract Number:

National Stock Number (NSN):

Contractor's Name:

2.3 Materials.

2.3.1 Cloth, duck, nylon. The cloth for the duffel bag shall be nylon duck, plain weave, dyed Camouflage Green 483, water repellent treated and coated on the back with a suitable clear polyurethane coating compound. If plasticizers are used in the coating, only phosphate or phthalate ester type plasticizers shall be used. The color of the dyed cloth shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight and that have a correlated color temperature of 7500 ± 200 K, with illumination of 100 ± 20-foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 ± 200 K. The finished cloth shall not present a dermal health hazard when used as intended (see paragraph 2.3.1.1), and shall conform to the requirements in Table I.

TABLE I Physical requirements for nylon duck.

Characteristic Requirement Test Method Weight (oz./sq. yd.) 10.5 - 12.0 ASTM-D3776 Option C Yarns per inch (min.) ASTM-D3775 Warp 35 Filling 28 Breaking strength (lbs., min.) ASTM-D5034 Warp 500 Filling 300 Colorfastness to: (minimum) Accelerated weathering “good” AATCC-169, Option 41/ Crocking 3.5 2/ AATCC-8 Spray rating (min.)

Initially 100, 100, 90 AATCC-22 After 1 laundering 90,90,80 AATCC-96 Test VI, A and AATCC-22 Hydrostatic resistance no leakage ASTM-D751 pH 4.5 - 8.5 AATCC-81 Dimensional stability (min.) AATCC-96 Test VI, A Warp 3.5 Filling 2.5

2.3.1.1 Toxicity assessment. The finished product must be composed of materials, which have been safely used commercially during prolonged, direct skin contact. Test methods for toxicity are: Primary dermal irritation study in laboratory animals (see paragraph 6.1, Acute Dermal Toxicity 870.1200) and a repeated insult human patch test (Modified Draize Procedure) (see paragraph 6.2, Principles and Methods of Toxicology). The latter must be conducted under the supervision of a qualified dermatologist using at least 100 free living individuals.

2.3.2 Nylon webbing. The woven nylon webbing for the shoulder strap, closing strap, handle and reinforcements shall be 1-23/32 inches wide, Camouflage Green 483, and shall be resin impregnated for strength. The untreated weight shall be 1.60 ounces per linear yard maximum.

The weight after webbing is resin impregnated shall be the untreated weight plus a maximum of ten percent. The cut ends of the nylon webbing shall be fused so they are seared smooth.

2.3.3 Thread, polyester. The thread shall be polyester, Camouflage Green 483, constructed of twisted soft multiple cord or twisted bonded multiple cord, with a nonwicking finish, 4 ply, with a minimum breaking strength of 10.6 lbs. when tested as specified in ASTM D-2256 (testing speed shall be 12 ± 0.5 in./min. and a 10-inch gauge length shall be used). There shall be no lubrication of the thread by any means prior to or during sewing. As an alternative, nylon thread may be used conforming to Type I or II, Class B (non-wicking), Tex 90-101 (Government size F) for Type I and Tex 90-112 (Government Size F) for Type II, 3 or 4 ply of A-A-59826. The thread shall be treated with an approved water repellent finish. The color shall match Camouflage Green 483.

2.3.4 Grommets. The duffel bag shall have 4 plain grommets with plain washers. The grommets and washers shall be brass with a black chemical finish, and substitute size number 6. THE

GROMMETS SHALL BE MADE IN ACCORDANCE WITH NASM16491.

2.3.5 Keeper, steel. The keeper shall be steel. It shall be fabricated from 0.135-inch nominal diameter carbon steel wire. The finish of the keeper shall consist of phosphate-treated zinc plate conforming to Type IV, SC3 (severe) of ASTM B633, followed by baked enameling. The enamel shall be black. The coating shall level out to a uniform continuous dry film of uniform black color with no objectionable orange peel, wrinkles, drops, streaks, or areas of thin or no film. The keeper dimensions are as specified on Drawing 2-3-301.

2.3.6 Snap hook, 1-1/8-inch fixed loop, with spring closure. The snap hook with spring closure shall have a steel wire body conforming to ITW Waterbury Buckle Co., style no. 00833-23- 21883 or equal (see paragraphs 4.1.1 and 6.3). The finish of the steel keeper shall consist of phosphate-treated zinc plate conforming to type IV, SC3 (severe) of ASTM B633, followed by baked enameling. The enamel shall be black.

2.3.7 Fastener, snap. The snap fastener shall be brass, with a regular wire spring clamp, black in color with a commercial dark oxide finish.

2.3.8 Shoulder pad cushion. The shoulder pad cushions shall be olefin, with a minimum weight of 8.25 ounces per square yard and a maximum weight of 19.5 ounces per square yard, color optional. As an alternate, 1/4 inch thick closed-cell soft cellular rubber may be used. The size of the pad shall be 14 inches by 2-1/4 inches (± 1/4 inch).

2.3.9 Adapter. The shoulder strap adjuster shall conform to Waterbury Buckle Part No. 09273- 09-21883 (see 4.1.1, 6.3 and Drawing 2-3-0638) or equal. The buckle shall be 1-7/8 inches and meet a minimum tensile strength requirement of 250 pounds when tested at 20 inches per minute.

The color shall be black.

2.4 Label/tag. Each item shall be individually bar-coded with a paper tag for personal clothing items. The paper tag shall be standard bleached sulfate having a basis weight of 100 pounds. The paper used for the tags shall have a smooth finish to accept thermal transfer and direct printing.

The tags shall have a hole and shall be attached to each item by a fastener, clearly legible and readable by a scanner. The bar-coding element shall be a 13-digit national stock number (NSN).

The bar code type shall be a medium to high code density and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that it causes no damage to the item.

2.5 Finished measurements. The duffel bags shall conform to the finished measurements specified in Table II.

Table II. Finished Measurements (inches)

Length 1/ 37 (+1, -1/2) Width 2/ 12-1/2 (+1/2, -1/4) Top hem width 3/ 3 (+/- 1/8) Cover flap width 4/ 10-1/2 (+1/2, -1/4) Cover flap length 5/ 12-1/2 (+1/2, -1/4) Carrying handle length 6/ 11-1/4 (+/- 1/8) Shoulder adjustment strap length 7/ 26 (+/- 1) Shoulder strap assembly 8/ 21 (+/- 1/2) Pocket width 9/ 5 (+/- 1/4) Pocket height 10/ 7 (+/- 1/4) Pocket flap width 11/ 5-1/2 (+/- 1/4) Pocket flap height 12/ 2 (+/- 1/8)

1/ Body length shall be taken along the rear of the bag, from top of folded hem to seam connecting the bottom piece to the body of the bag. Measure the length in two locations 180 degrees apart.

2/ Body width shall be taken at bottom panel, near center, from seam to seam, in both directions.

3/ Top hem width shall be taken at top stitch line of bag to bottom stitch line of hem in several locations.

4/ Cover flap width shall be taken from edge to edge near center of flap.

5/ Cover flap length shall be taken from top to bottom edge near center of flap.

6/ Carrying Handle length shall be taken along center of handle, from edge of webbing reinforcement to edge of opposite reinforcement.

7/ Shoulder adjustment strap shall be taken from top of strap to bottom of strap at bottom seam.

8/ Shoulder strap assembly shall be taken along the center of shoulder strap, from fold line at strap assembly to fold line above fastener.

9/ Pocket width shall be taken across middle of pocket from edge to edge.

10/ Pocket length shall be taken at center of pocket from top to bottom edge.

11/ Pocket flap width shall be taken at middle of pocket flap from edge to edge.

12/ Pocket flap length shall be taken at center pocket flap from top to bottom edge

3 REGULATORY REQUIREMENTS.

3.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

4 PRODUCT CONFORMANCE PROVISIONS.

4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description and shall conform to the producer’s own higher level quality standards and quality assurance practices. The Government reserves the right to require proof of such conformance.

4.1.1 Equal items. Prior to the use of an “or equal” item, the supplier shall submit the item with supporting data to the contracting officer for subsequent approval or disapproval by the responsible military agency.

4.2 Visual examination. Bags shall be inspected in accordance with ASQ/ANSI Z1.4, published by The America Society for Quality Control. The sample unit is one bag. Each duffel bag shall be inspected for the defects listed below (see Paragraph 4.2.1).

4.2.1 Manufacturing defects. Any hole, cut, or tear; color not as specified, any part shaded, any spot or stain (outside). Any material defects clearly visible: any smash, weak place, broken or missing yarn, multiple floats, or open place, shade bar; coated side of cloth tacky, uncoated side of cloth not facing out. Raw edges (on edge required to be finished), open seams, thread ends not trimmed to 1/4-inch maximum length, distorted parts, more than 1/2 inch securely caught in stitching, needle chews, seams pleated or badly puckered, runoff, loose tension resulting in a loosely secured seam; tight tension (stitches break when normal strain is applied to seam or stitching). Measurement and dimensions of item not as specified, any component omitted, misplaced, or not as specified, bottom of bag not set to body as specified, i.e., center of bottom not aligned with center of handle and carrying strap assembly. Any mend, darn, patch, or splice, any drill hole in fabric, hems twisted or pleated, any part of stitching attaching handle and handle reinforcements to body not stitched through body reinforcement. Edges of grip section overlapped, ends of carrying strap not finished as specified, pocket and pocket flap not attached to body of bag as specified, snap fastener components misplaced or not properly aligned failing to effect a smooth and secure closure. Ends of strap not finished as specified; any part of stitching requiring attaching nylon webbing to body of bag not stitched through body and reinforcement, shoulder adjustment strap not caught in between bottom and body, finished length of closing strap is longer or shorter than specified dimension and applicable plus or minus tolerance.

4.2.2 Attachment of grommets and fasteners defects. Adapter improperly set or fails to function properly; grommets improperly set with washer on inside of bag; holes not punched to receive grommets or fasteners; grommet fails to accommodate keeper; clinched excessively tight cutting fabric or insecurely clinched, i.e., grommet or washer becomes disengaged; clinched loosely, allowing grommet to rotate in hole; roll of grommet contains more than three scores (splits);

grommet not completely surrounded by grommet reinforcement patch; grommet set off center of hem by more than 1/4 inch; any score (splits) exceeding 1/16 inch in length; keeper improperly set or located; snap fastener has improper or insecure clinching; clinched excessively tight, cutting adjacent material; clinched loosely, permitting components to rotate freely in the hole of the material; incorrect style of snap fastener; roll of clinched eyelet fastener assembly contains more than three scores (splits).

4.2.3 Label and marking defects. Bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item. Marking omitted, incorrect, illegible, misplaced, or size of characters not as specified.

4.2.4 Webbing defects. Any hole, cut, tear or smash in webbing, webbing not firmly and tightly woven, edges frayed or scalloped; cut ends of nylon webbing not fused.

4.2.5 Hardware defects. Hardware broken or malformed, finish omitted, burrs, sharp edges, corroded areas; area of thin or no film, i.e., bare metal exposed; enamel finish (where applicable) is not uniform and adherent, i.e., objectionable orange peel, wrinkles, drops or streaks. Keeper fails to function or engage with snap hook; any fastener not functioning properly, i.e., fails to snap closed, provide a secure closure, or open freely.

4.2.6 Packaging defects. Any containers not packaged as specified and in accordance with the contract or purchase order.

4.3 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order.

5 PACKAGING

5.1 Preservation, packing, and marking. Preservation, packing, and marking shall be as specified in the contract or purchase order.

6 NOTES.

6.1 Source of Government documents. Copies of military and Federal documents are available from:

Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Environmental Protection Agency Office of Prevention, Pesticides and Toxic Substances

870.1200 (Acute Dermal Toxicity)

(Copies may be obtained from the U.S. Government Printing Office, Washington, DC 20402, or from the Environmental Protection Agency at 800 490-9198.)

6.2 Source of non-Government documents

ASTM B-633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel

ASTM D-751 - Standard Test Methods for Coated Fabrics ASTM D-2256 - Tensile Properties of Yarns by the Single-Strand Method ASTM D-3775 - Standard Test Method for Fabric Count of Woven Fabric ASTM D-3776 - Standard Test Method for Mass Per Unit Area (Weight) of Fabric ASTM D-5034 - Breaking Force and Elongation of Textile Fabrics (Grab Test) ASTM D-6193 - Standard Practice for Stitches and Seams

(Applications for copies should be addressed to American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428.)

AATCC 8 - Colorfastness to Crocking: AATCC Crockmeter Method AATCC 22 - Water Repellency: Spray Test AATCC 81 - pH of the Water-Extract from Wet Processed Textiles AATCC 96 - Dimensional Changes in Commercial Laundering of Woven and Knitted

Fabrics Except Wool AATCC 169, Opt 4 - Weather Resistance of Textiles: Xenon Lamp Exposure

(Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Research Triangle Park, NC 27709-2215.)

Principles and Methods of Toxicology, A. Wallace Hayes (editor), 1989, pp. 394-396.

(Applications for copies should be addressed to Raven Press, 1185 Avenue of the Americas, New York, NY 10036.)

ASQ/ANSI Z1.4 -Sampling Procedures and Tables for Inspection by Attributes

(ASQ/ANSI standards are available online at http://www.asq.org or from the American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203.)

6.3 Ordering data. Purchasers should select the preferred options permitted herein and include the following information in procurement documents (if applicable).

a. Title, number, and date of this document.

b. Label requirement (see 2.4)

c. Toxicity requirement (see 2.3.1)

d. Acceptance Criteria (see 4.2)

e. Packaging requirements (see 5.1).

6.4 Key words.

Duffel Bag Camouflage 483

6.3 Source for snap hook and adapter. A suggested source for the duffel bag snap hook specified in 2.3.6 and the adjuster (Waterbury Buckle Part No 09273-09-21883) specified in 2.3.9 is ITW Nexus, 952 S. Main Street, Waterbury, CT 06706, Telephone Number (203) 240-7110.

6.4 Source for standard samples. Contact the contracting agency for information on obtaining a standard sample for Camouflage Green 483.

Figure I Bag, Duffel

Figure II Bag, Duffel

Figure III Bag, Duffel

MILITARY INTERESTS:

Custodians: Civil Agency Coordinating Activity:

Army-GL GSA-FSS Navy-NU Preparing Activity:

DLA – CT

(Project Number 8465-2020-003)

NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.dla.mil/.