B01 Attachment J01d IHS_SD Employee Housing-Crawl House_ARCH_R23_B04 RFI.pdf

RELEVANT CODES AND STANDARDS [LATEST SHALL APPLY]

• NATIONAL FIRE CODES (NFC)

• NFPA 101 – LIFE SAFETY CODE

• INTERNATIONAL RESIDENTIAL CODE (IRC)

• INTERNATIONAL BUILDING CODE (IBC)

• ARCHITECTURAL BARRIERS ACT (ABA) STANDARDS

• INTERNATIONAL ENERGY CONSERVATION CODE (IECC)

• IHS TECHNICAL HANDBOOK

• ASHRAE STANDARD 111 “PRACTICES FOR MEASUREMENT,

TESTING, ADJUSTING, AND BALANCING OF BUILDING HEATING,

VENTILATION, AIR-CONDITIONING AND REFRIGERATION

SYSTEMS.

• ALL APPLICABLE IEEE STANDARDS

• ASHRAE GUIDELINE 0, THE COMMISSIONING PROCESS

• INTERNATIONAL PLUMBING CODE (IPC)

BUILDING DATA

STORIES: 1 W/ CRAWL SPACE

BUILDING AREA:

UNIT A UNIT B TOTAL

LEVEL ONE 1176 1176 2352

TOTAL 2359 2359

OCCUPANCY: RESIDENTIAL - ONE AND TWO-FAMILY DWELLINGS

PER NFPA 101 - 6.1.8.1.1

IECC COMPLIANCE PATH: PRESCRIPTIVE

SPRINKLERED: YES

FIRE ALARM: YES

PARKING: INTERIOR GARAGE W/ DRIVEWAY

AUTHORITY HAVING JURISDICTION (AHJ): DIRECTOR, DIVISION OF

ENGINEERING SERVICES (DES), INDIAN HEALTH SERVICE.

2020 INTERNATIONAL RESIDENTIAL CODE (IRC)

(R101.2) SCOPE: APPLIES TO DETACHED ONE AND TWO-FAMILY DWELLINGS WITH

A SEPARATE MEANS OF EGRESS NO MORE THAN 3 STORIES ABOVE GRADE PLANE.

CHAPTER 3: BUILDING PLANNING

(R302) FIRE-RESISTANT CONSTRUCTION

TABLE R302.1(2) EXTERIOR WALLS (SPRINKLERED BLDGS LPER P2904)

WALL ELEMENT MIN FIRE-RATING MIN FIRE SEPARATION DIST

WALLS FIRE-RATED 1-HR PER IBC 703.3 0 FT

NOT FIRE-RATED 0 HOURS 3 FT

PROJECTIONS

FIRE-RATED 1-HR, HT, OR FRT WOOD 2 FT

NOT FIRE-RATED 0 HOUR 3 FT

OPENINGS

UNLIMITED 0 HOUR 3 FT

PENETRATIONS

ALL COMPLY WITH R302.4 < 3 FT

(R302.3) TWO-FAMILY DWELLINGS

A. DWELLING UNITS TO BE SEPARATED BY WALL AND FLOOR ASSEMBLIES

WITH FIRE RATING >/= 1/2-HR PER ASTM E119, UL 263 OR 703.3 OF IBC.

EXTEND TO EXT WALLS AND FROM FOUNDATION TO UNDERSIDE OF

ROOF SHEATHING.

B. WALL ASSEMBLIES NEED NOT EXTEND THROUGH ATTIC SPACES WHERE:

1. CEILING PROTECTED BY 5/8” TYPE ‘X’ GYPSUM BOARD

2. ATTIC DRAFT STOP PER R302.12.1 PROVIDED ABOVE AND ALONG

SEPARATION WALL AND

3. STRUCTURAL FRAMING SUPPORTING THE CEILING TO BE

PROTECTED BY ½” GYPSUM BOARD OR EQUAL.

a. SUPPORTING CONSTRUCTION OF RATED FLOOR ASSEMBLIES

TO HAVE EQUAL OR GREATER RATING.

(R302.4) DWELLING UNIT FIRE-RATED PENETRATIONS

(R302.4.1) THROUGH PENETRATIONS

(R302.4.2) MEMBRANE PENETRATIONS: COMPLY WITH R302.4.1.

(R302.5) DWELLING TO GARAGE:

(R302.5.1) OPENINGS

(R302.5.2) DUCT PENETRATIONS

TABLE R302.6 DWELLING TO GARAGE FIRE SEPARATION

SEPARATION MATERIAL

RESIDENCE AND ATTICS 1/2 INCH MIN GYPSUM BD

HABITABLE ROOMS ABOVE 5/8 INCH MIN TYPE ‘X’ GYPSUM BD

STRUCTURE FOR FLOOR/CEILING 1/2 INCH MIN GYPSUM BD

GARAGE LOCATED LESS THAN 1/2 INCH MIN GYPSUM BD INTERIOR SIDE

3 FT FROM DWELLING UNIT OF EXTERIOR WALLS.

(R302.7) UNDER-STAIR PROTECTION: PROTECT ENCLOSED SPACE WITH 1/2”

GYPSUM BOARD.

(R302.9) FLAME SPREAD AND SMOKE DEVELOPED INDEX FOR FINISHES.

• WALL AND CEILING FINISHES FLAME SPREAD INDEX </= 200.

• WALL AND CEILING FINISHES SMOKE DEVELOPED INDEX </= 450.

(R302.10.1) INSULATION SHALL HAVE FLAME SPREAD INDEX </= 25 AND SMOKE

DEVELOPED INDEX </= 450. INCLUDES FACINGS, VAPOR RETARDERS, ETC.

(R302.11) FIREBLOCKING: LOCATIONS:

1. STUD WALLS – VERTICALLY AT CEILING AND FLOOR LEVELS.

2. STUD WALLS – HORIZONTALLY AT INTERVALS </= 10 FEET.

3. CONCEALED VERTICAL AND HORIZONTAL SPACES AT SOFFITS, DROP

CEILINGS, ETC.

4. VENT, PIPE, DUCT, CABLES, WIRES AT CEILING AND FLOOR LEVEL WITH

APPROVED FIRE-STOPPING MATERIALS.

5. CHIMNEYS AND FIREPLACES.

(R302.12) DRAFTSTOPPING: INSTALL IN CONCEALED SPACES OF FLOOR-CEILING

ASSEMBLIES TO DIVIDE INTO EQUAL SPACES </= 1000 SF.

(R302.13) FIRE PROTECTION OF FLOORS: IF NOT REQUIRED TO BE FIRE-RATED,

PROTECT UNDERSIDE OF FLOOR FRAMING WITH ½” GYPSUM BOARD MEMBRANE,

5/8” WOOD STRUCTURAL PANEL MEMBRANE, OR EQUAL.

EXCEPTIONS:

1. FLOOR ASSEMBLY OVER SPACE PROTECTED BY SPRINKLERS

2. FLOOR ASSEMBLY OVER SPACE NOT INTENDED FOR STORAGE OR

FUEL-FIRED OR ELECTRIC-POWERED HEATING APPLIANCES.

3. FLOOR ASSEMBLIES PERMITTED TO BE UNPROTECTED IF

UNPROTECTED PORTION </= 80 SQUARE FEET PER STORY.

4. FIREBLOCKING PER R302.11.1 INSTALLED ALONG PERIMETER OF

UNPROTECTED PORTION.

5. WOOD FLOOR ASSEMBLIES USING 2X10 DIMENSION LUMBER OR

EQUAL OR OTHER ASSEMBLY OF EQUIVALENT FIRE PERFORMANCE.

(R302.14) COMBUSTIBLE INSULATION CLEARANCE: KEEP MIN 3 INCHES FROM

RECESSED LIGHTS, FAN MOTORS, ETC. (UNLESS LISTED OTHERWISE).

SECTION R303: LIGHT, VENTILATION, AND HEATING

(R303.5.1) INTAKE OPENINGS: LOCATE NOT LESS THAN 10 FEET FROM

HAZARDOUS OR NOXIOUS CONTAMINANTS.

(R303.5.2) EXHAUST OPENINGS: SHALL NOT BE DIRECTED ONTO WALKWAYS.

SECTION R304: MINIMUM ROOM AREAS

(R304.1) MINIMUM AREA: HABITABLE ROOMS MIN 70 SF.

(R304.2) MINIMUM DIMENSIONS: NOT LESS THAN 7 FEET IN ANY HORIZONTAL

DIRECTION.

(R304.3) HEIGHT EFFECT ON ROOM AREA: FLOOR AREA BELOW SLOPED CEILINGS

LESS THAN 5 FT AND FURRED CEILINGS LESS THAN 7 FT DOES NOT CONTRIBUTE

TO HABITABLE AREA OF ROOM.

SECTION R305: CEILING HEIGHT

(R305.1) MINIMUM HEIGHT: HABITABLE SPACE, HALLWAYS NOT LESS THAN 7 FEET.

BATHROOMS, TOILET ROOMS, LAUNDRY ROOMS NOT LESS THAN 6’-8”.

SECTION R306: SANITATION

(R306.1) TOILET FACILITIES: WATER CLOSET, LAVATORY, AND BATHTUB OR

SHOWER REQUIRED IN EVERY DWELLING UNIT.

SECTION R307: TOILET, BATH, AND SHOWER SPACES

(R307.1) SPACE REQUIRED: FIXTURES SPACED PER P2705.1.

(R307.1) SPACE REQUIRED: FIXTURES SPACED PER P2705.1.

2021 INTERNATIONAL ENERGY CONSERVATION CODE (IECC)

IECC RESIDENTIAL PROVISIONS

CHAPTER 1 [RE]:

(R103.2) INFORMATION REQUIRED ON CONSTRUCTION DOCUMENTS

1. ENERGY COMPLIANCE PATH: PRESCRIPTIVE

(R103.2.1) THERMAL ENVELOPE: REPRESENT ON DOCUMENTS

(R105.2) REQUIRED INSPECTIONS

1. FOOTING AND FOUNDATIONS

2. FRAMING AND ROUGH-IN

3. PLUMBING ROUGH-IN

4. MECHANICAL ROUGH-IN

5. FINAL INSPECTION

SECTION R402: BUILDING THERMAL ENVELOPE

TABLE R402.1.2 MAX U-FACTORS BY COMPONENT (CLIMATE ZONE 6A)

FENESTRATION U-FACTOR 0.30

SKYLIGHT U-FACTOR 0.55

GLAZED FENETRATION SHGC NR

CEILING U-FACTOR 0.024

WOOD FRAME WALL U-FACTOR 0.045

MASS WALL U-FACTOR 0.060

FLOOR U-FACTOR 0.033

BASEMENT WALL U-FACTOR 0.050

CRAWL SPACE WALL U-FACTOR 0.055

TABLE R402.1.3 MIN R-VALUES BY COMPONENT (CLIMATE ZONE 6A)

FENESTRATION U-FACTOR 0.30

SKYLIGHT U-FACTOR 0.55

GLAZED FENETRATION SHGC NR

CEILING R-VALUE 0.060

WOOD FRAME WALL R-VALUE 20+5ci or 13+10ci or 0+20

MASS WALL R-VALUE 15/20

FLOOR R-VALUE 30

BASEMENT WALL R-VALUE 15ci or 19 or 13+5ci SLAB R-VALUE & DEPTH 10ci, 4 FT CRAWL SPACE WALL R-VALUE 15ci or 19 or 13+5ci

(R402.2.1) CEILINGS WITH ATTICS: EXTEND UNCOMPRESSED INSUL OVER WALL TOP

PLATE TO ALLOW LOWER R-VALUE INSUL TO BE USED.

(R402.2.2) CEILINGS WITHOUT ATTICS: WHERED REQUIRED INSULTATION > R-30,

BUT ROOF/CEILING ASSEMBLY DOES NOT ALLOW SUFFICIENT SPACE, MIN UNSUL

VALUE = R-30 FOR MAX 500 SF. INSUL SHALL EXTEND OVER WALL TOP PLATE.

(R402.2.4) ACCESS HATCHES AND DOORS FROM CONDITIONED TO UNCONDITIONED

SPACE – INSULATE TO LEVEL OF ADJACENT WALL.

(R402.2.8) BASEMENT WALLS: INSTALL INSUL FROM TOP OF WALL DOWN TO 10 FT

BELOW GRADE OR TO BASEMENT FLOOR.

(R402.2.9) SLAB-ON-GRADE FLOORS LOCATED LESS THAN 12 INCHES BELOW GRADE:

EXTEND INSULATION FROM TOP OF SLAB (INSIDE OR OUTSIDE OF FOUNDATION

WALL) VERTICALLY, HORIZONTALLY UNDER THE FLOOR SLAB, OR HORIZONTALLY

OUT FROM THE BUILDING (PROTECTED BY PAVEMENT OR 10+ INCHES OF SOIL).

(R402.2.10) INSULATED CRAWL SPACE WALLS: IF CRAWL SPACE NOT VENTED TO

OUTSIDE, INSUL TO EXTEND FROM UNDERSIDE OF FLOOR DOWNWARD TO FINISHED

GRADE AND THEN VERTICALLY OR HORIZONTALLY AN ADDITIONAL 24 INCHES.

EXPOSED EARTH IN UNVENTED CRAWL SPACE TO BE COVERED WITH CONTINUOUS

CLASS 1 VAPOR RETARDER. EXTEND UP FOUNDATION WALLS MIN 6 INCHES.

(R402.4.1) BUILDING THERMAL ENVELOPE: INSTALL PER MFR’S INSTRUCTIONS AND

PER TABLE R402.4.1.1.

(R402.4.3) FENESTRATION AIR LEAKAGE: </= 0.32 CFM PER SF FOR WINDOWS,

SKYLIGHTS, AND SLIDING DOORS, AND </= 0.5 CFM PER SF FOR SWINGING DOORS

PER NFRC 400. EXCEPTION: SITE-BUILT WINDOWS, SKYLIGHTS, AND DOORS.

(R402.5) MAX FENESTRATION U-FACTOR = 0.40 IN CLIMATE ZONE 6. AVERAGE MAX

SHGC = 0.50.

SECTION R308: GLAZING

(R308.1) IDENTIFICATION

(R308.3) HUMAN IMPACT LOADS

(R308.4) HAZARDOUS LOCATIONS:

1. DOORS: GLAZING IN FIXED OR OPERABLE PANELS IN SWINGING,

SLIDING, OR BI-FOLD DOORS.

2. GLAZING ADJACENT TO DOORS: WHERE BOTTOM EDGE OF GLASS < 60

INCHES ABOVE FLOOR OR WALKING SURFACE AND WITHIN 24 INCHES

EITHER SIDE OF THE DOOR IN THE CLOSED POSITION.

3. GLAZING IN WINDOWS: HAS TO MEET ALL THE FOLLOWING CONDITIONS:

• EXPOSED AREA OF INDIVIDUAL PANE LARGER THAN 9 SF.

• BOTTOM EDGE OF GLAZING < 18 INCHES ABOVE THE FLOOR.

• TOP EDGE OF GLAZING > 36 INCHES ABOVE FLOOR.

• WALKING SURFACE WITHIN 36 INCHES OF GLAZING.

(R308.4.5) GLAZING ADJACENT TO HOT TUBS, SPAS, SAUNAS, STEAM ROOMS,

BATHTUBS, SHOWERS, SWIMMING POOLS WHERE BOTTOM EDGE OF GLAZING

LESS THAN 60 INCHES ABOVE ANY STANDING OR WALKING SURFACES.

(R308.4.6) GLAZING ADJACENT TO STAIRS AND RAMPS

(R308.4.7) GLAZING ADJACENT TO BOTTOM LANDING OF STAIR.

SECTION R310: EMERGENCY ESCAPE AND RESCUE OPENINGS

(R301.1) LOCATIONS REQUIRED: BASEMENTS, HABITABLE ATTICS, EVERY

SLEEPING ROOM. TO OPEN DIRECTLY INTO A PUBLIC WAY, YARD OR COURT.

(R310.2.1) MINIMUM OPENING: NET CLEAR AREA >/= 5.7 SF. NET CLEAR MIN

HEIGHT 24 INCHES AND NET MIN CLEAR WIDTH 20 INCHES. MIN NET CLEAR

OPENING FOR AT-GRADE OR BELOW-GRADE OPENINGS >/= 5 SF.

(R310.2.2) WINDOWSILL HEIGHT: </= 44 INCHES ABOVE FLOOR OR IF BELOW

GRADE, PROVIDE A WINDOW WELL.

SECTION R311: MEANS OF EGRESS

(R311.2) EGRESS DOOR: NOT LESS THAN ONE, SIDE-HINGE, MIN WIDTH 32 INCHES,

CLEAR HEIGHT 78 INCHES MIN.

(R311.3) LANDING ON EACH SIDE OF EACH EXTERIOR DOOR REQD. MIN WIDTH >/=

WIDTH OF DOOR, MIN 36 INCHES LONG IN DIRECITON OF TRAVEL.

(R311.3.1) FLOOR ELEVATIONS AT REQUIRED EGRESS DOORS:

(R311.7) STAIRWAYS

(R311.7.1) WIDTH: NOT LESS THAN 36” CLEAR ABOVE HANDRAIL HEIGHT, MIN 31 1/2”

BELOW HANDRAIL. (31 1/2” WHERE HANDRAIL ON ONE SIDE)

(R311.7.2) HEADROOM: MIN 6’-8”.

(R311.7.3) VERTICAL RISE: MAX RISE FOR A FLIGHT OF STAIRS 151 INCHES

BETWEEN FLOORS OR LANDINGS.

(R311.7.8.1) HANDRAIL HEIGHT: >/= 34 INCHES NOR MORE THAN 38 INCHES

(R311.7.8.4) CONTINUITY: CONTINUOUS FOR FULL LENGTH OF THE FLIGHT.

(R311.8) RAMPS: MAX SLOPE FOR EGRESS DOORS 1:12. OTHER RAMPS MAX 1:8.

WHERE TECHNICALLY INFEASIBLE, RAMPS CAN HAVE MAX SLOPE 1:8.

(R311.8.2) LANDINGS REQUIRED AT TOP AND BOTTOM, AT DOORS, AT DIRECTION

CHANGES, MIN WIDTH 36”.

(R311.8.3) HANDRAILS REQUIRED ON MIN ONE SIDE WHERE SLOPE > 1:12.

(R311.8.3.1) HANDRAIL HEIGHT: >/= 34 INCHES OR MORE THAN 38 INCHES.

(R311.8.3.3) HANDRAILS: TO BE CONTINUOUS FOR FULL LENGTH OF RAMP.

SECITON R312: GUARDS AND WINDOW FALL PROTECTION:

(R312.1) GUARDS: PROVIDE AT OPEN SIDE OF WALKING SURFACES > 30 INCHES

ABOVE ADJACENT FLOOR OR GRADE. MIN HEIGHT 36 INCHES. INSECT SCREEN

NOT CONSIDERED A GUARD. NO OPENINGS TO ALLOW PASSAGE OF 4 INCH

SPHERE.

(R312.2) WINDOW FALL PROTECTION: WHERE WINDOW SILL LESS THAN 24 INCHES

ABOVE FINISHED FLOOR AND MORE THAN 72 INCHES ABOVE GRADE:

• WINDOW OPENING SHALL NOT ALLOW PASSAGE OF 4 INCH SPHERE, OR

• WINDOW PROVIDED WITH FALL PROTECTION PER ASTM F2090, OR

• WINDOW PROVIDED WITH OPENING CONTROL DEVICES PER SECTION

R310.2.1.

(R312.2.2) WINDOW OPENING CONTROL DEVICES. WILL ALLOW WINDOW TO OPEN

FULLY AS REQUIRED PER SECTION R310.2.1.

SECTION R314: SMOKE ALARMS PER NFPA 72 AND SECTION R314: SHALL BE

PROVIDED IN DWELLING UNITS (OR COMBINATION SMOKE AND CARBON

MONOXIDE ALARM)

(R314.3) LOCATIONS:

• EACH SLEEPING ROOM

• OUTSIDE EACH SLEEPING AREA IN VICINITY OF BEDROOMS

• ON EACH ADDITIONAL STORY INCLUDING BASEMENTS AND HABITABLE

ATTICS

• NOT LESS THAN 3 FEET FROM DOOR OPENING IN BATHROOM HAVING

BATHTUB OR SHOWER

• NOT LESS THAN 20 FEET FROM COOKING APPLIANCE (10 FEET IF

IONIZATION TYPE OR 6 FEET IF PHOTOELECTRIC TYPE)

(R314.4) IF ONE ALARM IS ACTIVATED, ALL ALARMS SHALL BE ACTIVATED.

SECTION R315: CARBON MONOXIDE ALARMS: REQUIRED WHERE DWELLING UNIT

CONTAINS A FUEL-FIRED APPLIANCE OR HAS AN ATTACHED GARAGE WITH AN

OPENING THAT COMMUNICATES WITH THE DWELLING UNIT.

SECTION R316: FOAM PLASTIC TO HAVE FLAME SPREAD INDEX NOT MORE THAN

75 AND SMOKE DEVELOPED INDEX NOT MORE THAN 450.

(R316.4) THERMAL BARRIER: SEPARATE FOAM PLASTIC FROM INTERIOR OF

BUILDING BY A LAYER OF NOT LESS THAN ONE-HALF INCH GYPSUM BOARD, 23/32

INCH WOOD STRUCTURAL PANEL, OR OTHER MATERIAL APPROVED PER NFPA 275.

(R316.5.2) ROOFING: THERMAL BARRIER PER SECTION R316.4 NOT REQUIRED

WHERE FOAM PLASTIC UNDER ROOF COVERING IS SEPARATED FROM INTERIOR

BY T&G WOOD PLANKS OR WOOD STRUCTURAL SHEATHING NOT LESS THAN 15/32

INCHES THICK EXTERIOR GLUE.

(R316.5.5) FOAM-FILLED EXTERIOR DOORS: EXEMPT FROM REQUIREMENTS OF

R316.3 AND R316.4.

(R316.5.6) FOAM-FILLED GARAGE DOORS: EXEMPT FROM REQUIREMENTS OF

R316.3 AND R316.

B.O. STRUCTURE

CEILING LINE

FLOOR LINE

2 X 4 WOOD STUDS @ 16"

O.C. W/ SOUND BATT.

2 X 4 WOOD STUDS @ 16"

O.C. (NO SOUND BATT.)

5/8" TYPE "X"

GYPSUM BOARD

A1

A2

2 X 4 WOOD STUDS @ 16"

O.C. (NO SOUND BATT.)

5/8" TYPE "X"

GYPSUM BOARD

6" WOOD STUDS @ 16"

O.C. (NO SOUND BATT.)

5/8" TYPE "X"

GYPSUM BOARD

2 x 4 WOOD STUDS @ 16"

O.C. W/ SOUND BATT.

B1

B2

A1 B1 C1A2 B2 C2

2 X 6 WOOD STUDS @

16"O.C. W/ SOUND BATT.

C2

C1

TREATED SILL PLATE

WHEN IN CONTACT W/

CONCRETE FLOOR

TREATED SILL PLATE

WHEN IN CONTACT W/

CONCRETE FLOOR

5/8" TYPE "X"

GYPSUM BOARD

D1

2 X 4 WOOD STUDS @

16"O.C. W/ SOUND BATT.

1"

PLYWOOD SHEATHING

WOOD TRUSS, RE:

STRUCTURAL DRAWINGS

R1

STANDING SEAM METAL ROOF

UNDERLAYMENT

CORNER INTERSECTION

METAL CORNER BEAD - FORM TIGHT 90 DG.

CORNER AND SCREW TO STUD

3 COAT JOINT COMPOUND COVER BEAD AND

FEATHER FOR SMOOTH FINISH

TYP. WOOD STUD AND DRYWALL SCREWS

JOINT TAPE, TYP.

5 GWB AS NOTED

ELEVATION

WOOD STUDS; SPACING AS

SPECIFIED

SUB FLOOR

SHEAR WALL BLOCKING;

RE: STRUCT

NOTE:

INSTALL DBL. STUDS AT WALL

MOUNTED PLBG. & ELECT. FIXTURES,

COUNTERS, TOILET PARTITIONS AND

OTHER SIMILAR EQUIP. LOCATIONS.

DOUBLE TOP PLATE

LAP DOUBLE TOP PLATE MIN 4'-0"

TOP CRIPPLES

HEADER; RE: STRUCT.

KING STUD

SILL 21

BOTTOM CRIPPLES5

TRIMMER STUD6

BOTTOM PLATE9

ROUGH OPENING

WINDOW

ROUGH OPENING

DOOR

R O

U G

H O

P E

N

IN

G

D O

O R

R O

U G

H O

P E

N

IN

G

W

IN

D O

W

R

SEH Project

Checked By

Drawn By

Project Status Issue Date

This drawing is an instrument of service and shall remain the property of Short Elliott Hendrickson, Inc.

(SEH). This drawing, concepts and ideas contained herein shall not be used, reproduced, revised, or retained without the express written approval of SEH.

Submission or distribution of this drawing to meet official or regulatory requirements or for purposes in connection with the project is not be construed as publication in derogation of any of the rights of SEH.

Project Owner

S ho rt E lli ot t H en dr ic ks on

, I nc

A ll

R ig ht s

R es er ve d

C O

P Y

R

IG

H T

Indian Health Service (IHS) Department of Health and Human Services Division of Engineering Services 701 Fifth Avenue, MS 24, Suite 1600 Seattle, Washington 98104-7307

8/

/2

2:

:1

P

M

CODE INFORMATION AND

CONSTRUCTION

ASSEMBLIES

S

IT

E A

D A

P T

D U

P L

E X

F

O R

T Y

A T

E S

, N D

D U

P L

E X

P A

C K

A G

E

C R

A W

L S

P A

C E

F

IF

T H

A V

E N

U E

, M S

4, S U

IT

E

S

E A

T T

LE

, W

A S

H

IN

G T

O N

4-

177917

A. JAUCH

J. HEGG

IN

D

IA

N

H E

A

LT

H S

E R

V

IC

E

G R

E A

T P

LA

IN

S A

R E

A

CONSTRUCTION

DOCUMENTS

03.31.2025

A002

CODE ANALYSIS

1 1/2" = 1'-0"A002

1 PARTITION TYPES

1" = 1'-0"A002

2 ROOF ASSEMBLIES

3" = 1'-0"A002

4 GWB PARTITION DETAILS - WOOD STUDS

1" = 1'-0"A002

5 WOOD STUD FRAMING DETAIL

REVISION SCHEDULE

REV. # DESCRIPTION DATE

WH W

D

W D

WH

A202

A201

A201

A202

A411

'-6

26'-0" 3 1/2" 15'-5 1/2" 8" 15'-5 1/2" 3 1/2" 26'-0"

'-1

25'-0 1/2" 3 1/2" 2'-1" 3 1/2" 13'-7"

6' -2

5'

-0

3'-7"

3 1/2" 7'-9 1/2"

'-3

/4

1/ 2"

2' -1

1/ 2"

'-1

/4

5'-3" 5'-11 1/2"

15'-11"

4' -6

A411

BEDROOM 1

101A

BEDROOM 2

104A

BATHROOM

107A

HALLWAY

105A

LIVING/DINING

110A

MECH

113A

ENTRY

108A

GARAGE

115A

'-0

'-4

42'-1" 42'-1"

26'-0" 16'-1" 16'-1" 26'-0"

CLOSET

102A

LINEN

106A

CLOSET

109A

CLOSET

103A

101A

108B

104B

101B

107B

103B

102B

108A

104A

107A

103A

102A

115A

111B

106B106A 109A

110A

LIVING/DINING

110B

KITCHEN

111B

MECH

113B

CLOSET

109B

ENTRY

108B BATHROOM

107B

HALLWAY

105B

BEDROOM 1

101B

CLOSET

102B

BEDROOM 2

104B

CLOSET

103B

LINEN

106B

GARAGE

115B

115B

5'-8" 3'-0" 10'-3" 3'-0" 3" 5'-0" 3" 3'-0" 2'-1" 3'-2" 1'-7" 3'-0" 1'-6" 4"

4' -7

3'

-0

'-1

0" 3'

-0

4' -7

110B

4" 1'-6" 3'-0" 1'-7" 3'-2" 2'-1" 3'-0" 3" 5'-0" 3" 3'-0" 10'-3" 3'-0" 5'-8"

'-0

5'-8" 3'-0" 11'-7 1/2" 5'-0" 8 1/2" 8 1/2" 5'-0" 11'-7 1/2" 3'-0" 5'-8"

84'-2"

2'-11" 9'-2" 4'-0" 4'-0" 9'-2" 2'-11"

4' -7

3'

-0

'-1

0" 3'

-0

4' -7

A301

A301

LAUNDRY

114B

KITCHEN

111A

113A 111A

LAUNDRY

114A

4'-9 1/2" 3'-1"

5' -7

PANTRY

112A

109B

PANTRY

112B

A411 45

113B

114B114A

A311

A311

112B112A

DW DW

W1

W1

W1

W1W1W2W1

W1

W1

W1

W1 W1 W2 W1 W1 W1

1 HOUR FIRE

PARTITION

1 HOUR FIRE

PARTITION

ATTIC ACCESS

HATCH 20"x30"

MIN CLEAR

ATTIC ACCESS

HATCH 20"X30"

MIN CLEAR

B1

1' -5

W1 W1

B2

7' -1

0" 3'

-0

9' -6

7' -1

0" 3'

-0

9' -6

CRAWL SPACE

ACCESS HATCH

18"x24" MIN CLEAR

CRAWL SPACE

ACCESS HATCH

18"x24" MIN .CLEAR

TOP OF CONCRETE STOOP 7" MAX

BELOW TOP OF FINISHED FLOOR

4'-0"

3' -0

4'-0"

3' -0

A2

A2

A1

A1A1 A2

A2

A1

A2

A1A1

A1

A1 A2

A2

A1

A1

A1

A1

A2

B1

D1

ATTIC ACCESS

HATCH 20"X30"

MIN CLEAR

ATTIC ACCESS

HATCH 20"X30"

MIN CLEAR

R

SEH Project

Checked By

Drawn By

Project Status Issue Date

This drawing is an instrument of service and shall remain the property of Short Elliott Hendrickson, Inc.

(SEH). This drawing, concepts and ideas contained herein shall not be used, reproduced, revised, or retained without the express written approval of SEH.

Submission or distribution of this drawing to meet official or regulatory requirements or for purposes in connection with the project is not be construed as publication in derogation of any of the rights of SEH.

Project Owner

S ho rt E lli ot t H en dr ic ks on

, I nc

A ll

R ig ht s

R es er ve d

C O

P Y

R

IG

H T

Indian Health Service (IHS) Department of Health and Human Services Division of Engineering Services 701 Fifth Avenue, MS 24, Suite 1600 Seattle, Washington 98104-7307

8/

/2

2:

:1

P

M

FLOOR PLAN - GROUND

FLOOR

S

IT

E A

D A

P T

D U

P L

E X

F

O R

T Y

A T

E S

, N D

D U

P L

E X

P A

C K

A G

E

C R

A W

L S

P A

C E

F

IF

T H

A V

E N

U E

, M S

4, S U

IT

E

S

E A

T T

LE

, W

A S

H

IN

G T

O N

4-

177917

A. JAUCH

J. HEGG

IN

D

IA

N

H E

A

LT

H S

E R

V

IC

E

G R

E A

T P

LA

IN

S A

R E

A

CONSTRUCTION

DOCUMENTS

03.31.2025

A102

PROJECT

NORTH

1/4" = 1'-0"A102

1 FLOOR PLAN - GROUND FLOOR

GENERAL NOTES

1. FIELD VERIFY ALL DIMENSIONS. NOTIFY OWNER IF DIMENSIONS VARY SIGNIFICANTLY.

2. ALL DIMENSIONS TO FACE OF WOOD STUD UNLESS NOTED OTHERWISE.

3. ALL INTERIOR WALLS TO BE WALL TYPE A-1 UNLESS NOTED OTHERWISE

W D

WH

A411

A411 45

KITCHEN

111B

PANTRY

112B

CLOSET

109B

LAUNDRY

114B

MECH

113B

DW

3' -3

3'

-1

1/ 2"

6' -1

/4

2'

-5

/2

3'-4 1/2"

4' -2

/4

3'

-3

/4

3'-3 1/4" 2'-7 1/2" 2'-1 1/4"

42" CLEAR

5' -7

9'

-1

1/ 4"

4'-7 3/4"

09.02

09.02

09.01

22.04

09.02 22.06

09.02

09.02

09.01

3' -0

3' -7

/2

09.02

11.03

09.01

09.02 11.01

11.02

09.02

08.0108.01 08.01

09.02

09.01

09.02

11.01

11.02

1 1/2"1'-6" 2'-6" 1'-6"1 1/2"

08.01

11.03 09.02 22.06

09.01

3' -0

09.02

1 1/2" 2'-9" 3'-0" 3'-0"

1'-6" 3'-0"

3' -0

09.02

09.01

09.02

A411 8

4'-9 3/4"

CL22.09

22.08

22.01

12.02

22.02

12.03 2' -6

/4

22.03

8' -1

/2

2'

-6

'-7

/2

1' -6

6' -6

1'-3 1/4"

CL

12.01

12.02

22.01

22.03

12.03

22.02

09.01

09.02

6' -6

22.10

22.09

22.03

22.01

12.01

06.09

1' -0

2'

-6

1' -8

2'

-1 0"

8' -0

1/

2" 2'

-4

/2

4"

2'-1"

1'-2 1/2"

1'-8" 4"

WHITE MELAMINE ADJUSTABLE

SHELVES

OAK DOORS

STAINLESS STEEL WIRE PULLS

OAK CABINET

SOLID SURFACE (SS-1)

COUNTERTOP W/ 4" BACK &

SIDE SPLASH

OAK CABINET

STAINLESS STEEL WIRE PULLS

BASE - REFER TO SCHEDULE

WHITE MELAMINE

ADJUSTABLE SHELVES

R

SEH Project

Checked By

Drawn By

Project Status Issue Date

This drawing is an instrument of service and shall remain the property of Short Elliott Hendrickson, Inc.

(SEH). This drawing, concepts and ideas contained herein shall not be used, reproduced, revised, or retained without the express written approval of SEH.

Submission or distribution of this drawing to meet official or regulatory requirements or for purposes in connection with the project is not be construed as publication in derogation of any of the rights of SEH.

Project Owner

S ho rt E lli ot t H en dr ic ks on

, I nc

A ll

R ig ht s

R es er ve d

C O

P Y

R

IG

H T

Indian Health Service (IHS) Department of Health and Human Services Division of Engineering Services 701 Fifth Avenue, MS 24, Suite 1600 Seattle, Washington 98104-7307

8/

/2

2:

:1

P

M

ENLARGED KITCHEN AND

BATHROOM PLANS AND

INTERIOR ELEVATIONS

S

IT

E A

D A

P T

D U

P L

E X

F

O R

T Y

A T

E S

, N D

D U

P L

E X

P A

C K

A G

E

C R

A W

L S

P A

C E

F

IF

T H

A V

E N

U E

, M S

4, S U

IT

E

S

E A

T T

LE

, W

A S

H

IN

G T

O N

4-

177917

A. JAUCH

J. HEGG

IN

D

IA

N

H E

A

LT

H S

E R

V

IC

E

G R

E A

T P

LA

IN

S A

R E

A

CONSTRUCTION

DOCUMENTS

03.31.2025

A411

1/2" = 1'-0"A411

1 ENLARGED PLAN - KITCHEN

1/4" = 1'-0"A411

2 KITCHEN - NOTRH

1/4" = 1'-0"A411

3 KITCHEN - SOUTH

1/4" = 1'-0"A411

4 KITCHEN - EAST

1/4" = 1'-0"A411

5 KITCHEN - WEST

1/4" = 1'-0"A411

6 BUFFET

KEYNOTE LEGEND

06.09 LAMINATE SHELFING W/ SUPPORT BRACKETS

08.01 WOOD DOOR, RE: DOOR SCHEDULE

09.01 PLAM COUNTERTOP W/3 MIL EDGE AND SET ON BACKSPLASH

09.02 OAK FINISH CABINET

11.01 RANGE, SPEC: TBD

11.02 MICROWAVE, SPEC: TBD

11.03 FRIDGE, SPEC: TBD

12.01 CURTAIN ROD, SPEC: TBD

12.02 TOILET PAPER DISPENSER, SPEC: TBD

12.03 VANITY MIRROR, SPEC: TBD

22.01 FLOOR MOUNTED WATER CLOSET, RE:PLUMB.

22.02 LAVATORY, RE: PLUMB.

22.03 ONE PIECE FIBERGLASS SHOWER SURROUND WITH TUB, SPEC: TBD

22.04 KITCHEN SINK, RE: PLUMB.

22.06 DISHWASHER, SPEC: TBD

22.08 CURTAIN ROD, SPEC: TBD

22.09 TOWEL HOOK, SPEC: TBD

22.10 SHOWER HEAD, RE: SPEC.

GENERAL NOTES

1. FIELD VERIFY ALL DIMENSIONS. NOTIFY OWNER IF DIMENSIONS VARY SIGNIFICANTLY.

2. ALL DIMENSIONS TO FACE OF WOOD STUD UNLESS NOTED OTHERWISE.

3. ALL INTERIOR WALLS TO BE WALL TYPE A-1 UNLESS NOTED OTHERWISE

1/2" = 1'-0"A411

7 ENLARGED PLAN - LEVEL 1

1/4" = 1'-0"A411

8 BATHROOM ELEV. - WEST

1/4" = 1'-0"A411

9 BATHROOM ELEV. - SOUTH

3/4" = 1'-0"A411

11 STANDARD HT. CASEWORK, TYP.