A00001_70Z04423RBOD62217 Attachment 3 Labor Definitions.pdf

70Z04423RBOD62217

Attachment 3 – Labor Definitions

ILMS II Labor Definitions Based on US DOL Wage and Hour Division Definitions (Fourth Edition)

23160 Electrician, Maintenance

Performs a variety of electrical trade functions such as the installation, maintenance, or repair of equipment for the generation, distribution, or utilization of electric energy. Work involves most of the following: Installing or repairing any of a variety of electrical equipment such as generators, transformers, switchboards, controllers, circuit breakers, motors, heating units, conduit systems, or other transmission equipment; working from blueprints, drawings, layouts, or other specifications; locating and diagnosing trouble in the electrical system or equipment; working standard computations relating to load requirements of wiring or electrical equipment; and using a variety of electrician's hand tools and measuring and testing instruments. In general, the work of the maintenance electrician requires rounded training and experience usually acquired through a formal apprenticeship or equivalent training and experience.

23181 Electronics Technician, Maintenance I

Applies technical knowledge to perform simple or routine tasks following detailed instructions.

Performs such tasks as replacing components and wiring circuits; repairing simple electronic equipment; and taking test readings using common instruments such as digital multimeters, signal generators, semiconductor testers, curve tracers, and oscilloscopes.

Receives technical guidance, as required, from supervisor or higher level technician. Work is spot-checked for accuracy.

23182 Electronics Technician, Maintenance II

Applies comprehensive technical knowledge to solve complex problems by interpreting manufacturers' manuals or similar documents. Work requires familiarity with the interrelationships of circuits and judgment in planning work sequence and in selecting tools and testing instruments.

Receives technical guidance, as required, from supervisor or higher level technician, and work is reviewed for compliance with accepted practices. May provide technical guidance to lower level technicians.

23183 Electronics Technician, Maintenance III

Applies advanced technical knowledge to solve unusually complex problems that typically cannot be solved solely by referencing manufacturers' manuals or similar documents. Examples of such problems include determining the location and density of circuitry, evaluating electromagnetic radiation, isolating malfunctions, and incorporating engineering changes.

Work typically requires a detailed understanding of the interrelationships of circuits. Exercises independent judgment in performing such tasks as making circuit analyses, calculating wave forms, and tracing relationships in signal flow. Uses complex test instruments such as high frequency pulse generators, frequency synthesizers, distortion analyzers, and complex computer control equipment. Work may be reviewed by supervisor for general compliance with accepted practices. May provide technical guidance to lower level technicians.

23931 Telecommunications Mechanic I

Installs, removes, maintains, modifies, troubleshoots, and repairs voice and/or nonvoice communications systems including intercom and public address systems; alarm systems; teletype equipment; and electronic and electromechanical telephone key systems/PBAXs; terminal and communications equipment, including line drivers. Runs cables, key cables, or house wire to all telephone sets, terminal connectors, lugs, pins, or screws, associated with key telephone equipment and/or terminating equipment for nonvoice circuits.

23932 Telecommunications Mechanic II

Installs, tests, troubleshoots, programs, maintains, and repairs digital switching equipment, attendant consoles, power and ringing relay racks, miscellaneous telephone, radio, fire alarms, intrusion alarms, and computer data circuits and related apparatus required in the central switching office. Analyzes system failures and other unusual system occurrences to isolate the source of the problem and determine whether the failure is caused by software, hardware, or other factors. They maintain manual and/or computerized central office records, including detail records, traffic analysis records, cable records, line records, subscriber service records and spare parts inventories.

23960 Welder, Combination, Maintenance

Welds metal components together to fabricate or repair products, such as machine parts, plant equipment, mobile homes, motors and generators, according to layouts, blueprints or work orders, using brazing and a variety of arc and gas welding equipment. Welds metal parts together, using both gas welding or brazing and any combination of arc welding processes.

Performs related tasks such as thermal cutting and grinding. Repairs broken or cracked parts, fills holes and increases size of metal parts. Positions and clamps together components of fabricated metal products preparatory to welding. May locate and repair cracks in industrial engine cylinder heads, using inspection equipment and gas torch. May perform repairs only. May be required to pass employer performance tests or standard tests to meet certification standards of governmental agencies or professional and technical associations.

30061 Drafter/CAD Operator I

Prepares drawings of simple, easily visualized structures, systems, parts or equipment from sketches or marked-up prints. Selects appropriate templates or uses a compass and other equipment needed to complete assignments. Drawings fit familiar patterns and present few technical problems. Supervisor provides detailed instructions on new assignments, gives guidance when questions arise, and reviews completed work for accuracy.

30062 Drafter/CAD Operator II

Prepares various drawings of such units as construction projects or parts and assemblies, including various views, sectional profiles, irregular or reverse curves, hidden lines, and small or intricate details. Work requires use of most of the conventional drafting techniques and a working knowledge of the terms and procedures of the occupation. Makes arithmetic computations using standard formulas. Familiar or recurring work is assigned in general terms. Unfamiliar assignments include information on methods, procedures, sources of information, and precedents to follow.

Simple revisions to existing drawings may be assigned with a verbal explanation of the desired results. More complex revisions are produced from sketches or specifications which clearly depict the desired product.

30063 Drafter/CAD Operator III

Prepares complete sets of complex drawings which include multiple views, detail drawings, and assembly drawings. Drawings include complex design features that require considerable drafting skill to visualize and portray. Assignments regularly require the use of mathematical formulas to draw land contours or to compute weights, center of gravity, load capacities, dimensions, quantities of material, etc. Works from sketches, models, and verbal information supplied by an engineer, architect, or designer to determine the most appropriate views, detail drawings, and supplementary information needed to complete assignments. Selects required information from precedents, manufacturers' catalogs, and technical guides. Independently resolves most of the problems encountered. Supervisor or design originator may suggest methods of approach or provide advice on unusually difficult problems.

30064 Drafter/CAD Operator IV

Works closely with design originators, preparing drawings of unusual, complex, or original designs which require a high degree of precision. Performs unusually difficult assignments requiring considerable initiative, resourcefulness, and drafting expertise. Assures that anticipated problems in manufacture, assembly, installation, and operation are resolved by the drawing produced. Exercises independent judgment in selecting and interpreting data based on a knowledge of the design intent. Although working primarily as a drafter, may occasionally interpret general designs prepared by others to complete minor details. May provide advice and guidance to lower level drafters or serve as coordinator and planner for large and complex drafting projects.

30081 Engineering Technician I

Performs simple routine tasks under close supervision or from detailed procedures. Work is checked in progress or on completion. Performs one or a combination of such typical duties as:

• Assembles or installs equipment or parts requiring simple wiring, soldering, or connecting.

• Performs simple or routine tasks or tests such as tensile or hardness tests; operates and adjusts simple test equipment; records test data.

• Gathers and maintains specified records of engineering data such as tests, drawings, etc.;

performs computations by substituting numbers in specified formulas; plots data and draws simple curves and graphs.

30082 Engineering Technician II

Performs standardized or prescribed assignments involving a sequence of related operations.

Follows standard work methods on recurring assignments but receives explicit instructions on unfamiliar assignments; technical adequacy of routine work is reviewed on completion;

nonroutine work may also be reviewed in progress. Performs at this level one or a combination of such typical duties as:

• Following specific instructions, assembles or constructs simple or standard equipment or parts; may service or repair simple instruments or equipment.

• Conducts a variety of tests using established methods. Prepares test specimens, adjusts and operates equipment, and records test data, pointing out deviations resulting from equipment malfunction or observational errors.

• Extracts engineering data from various prescribed but nonstandardized sources; processes the data following well-defined methods including elementary algebra and geometry;

presents the data in prescribed form.

30083 Engineering Technician III

Performs assignments that are not completely standardized or prescribed. Selects or adapts standard procedures or equipment, using fully applicable precedents. Receives initial instructions, equipment requirements, and advice from supervisor or engineer as needed;

performs recurring work independently; work is reviewed for technical adequacy or conformity with instructions. Performs at this level one or a combination of such typical duties as:

• Constructs components, subunits, or simple models or adapts standard equipment. May troubleshoot and correct malfunctions.

• Follows specific layout and scientific diagrams to construct and package simple devices and subunits of equipment.

• Conducts various tests or experiments which may require minor modifications in test setups or procedures as well as subjective judgments in measurement; selects, sets up, and operates standard test equipment and records test data.

• Extracts and compiles a variety of engineering data from field notes, manuals, lab reports, etc.; processes data, identifying errors or inconsistencies; selects methods of data presentation.

• Assists in design modification by compiling data related to design, specifications, and materials which are pertinent to specific items of equipment or component parts.

Develops information concerning previous operational failures and modifications. Uses judgment and initiative to recognize inconsistencies or gaps in data and seek sources to clarify information.

30084 Engineering Technician IV

Performs nonroutine assignments of substantial variety and complexity, using operational precedents which are not fully applicable. Such assignments, which are typically parts of broader assignments, are screened to eliminate unusual design problems. May also plan such assignments. Receives technical advice from supervisor or engineer; work is reviewed for technical adequacy (or conformity with instructions). May be assisted by lower level technicians and have frequent contact with professionals and others within the establishment.

Alone, or in a team environment, perform or support installation, testing, verification, repair, diagnostic analysis, and calibration of various systems. Provide organizational, intermediate, and depot level troubleshooting and support of fielded systems Performs at this level one or a combination of such typical duties as:

• Develops or reviews designs by extracting and analyzing a variety of engineering data.

Applies conventional engineering practices to develop, prepare, or recommend schematics, designs, specifications, electrical drawings and parts lists. Examples of designs include: detailed circuit diagrams; hardware fittings or test equipment involving a variety of mechanisms; conventional piping systems; and building site layouts.

• Conducts tests or experiments requiring selection and adaptation or modification of a wide variety of critical test equipment and test procedures; sets up and operates equipment; records data, measures and records problems of significant complexity that sometimes require resolution at a higher level; and analyzes data and prepares test reports.

• Applies methods outlined by others to limited segments of research and development projects; constructs experimental or prototype models to meet engineering requirements; conducts tests or experiments and redesigns as necessary; and records and evaluates data and reports findings.

30085 Engineering Technician V

Performs nonroutine and complex assignments involving responsibility for planning and conducting a complete project of relatively limited scope or a portion of a larger and more diverse project. Selects and adapts plans, techniques, designs, or layouts. Contacts personnel in related activities to resolve problems and coordinate the work; reviews, analyzes, and integrates the technical work of others. Supervisor or professional engineer outlines objectives, requirements, and design approaches; completed work is reviewed for technical adequacy and satisfaction of requirements. Alone, or in a team environment, perform or support installation, testing, verification, repair, diagnostic analysis, and calibration of various systems. Provide organizational, intermediate, and depot level troubleshooting and support of fielded systems.

May train and be assisted by lower level technicians. Performs at this level one or a combination of such typical duties as:

• Designs, develops, and constructs major units, devices, or equipment; conducts tests or experiments; analyzes results and redesigns or modifies equipment to improve performance; and reports results.

• From general guidelines and specifications (e.g., size or weight requirements), develops designs for equipment without critical performance requirements which are difficult to satisfy such as engine parts, research instruments, or special purpose circuitry. Analyzes technical data to determine applicability to design problems; selects from several possible design layouts; calculates design data; and prepares layouts, detailed specifications, parts lists, estimates, procedures, etc. May check and analyze drawings or equipment to determine adequacy of drawings and design.

• Plans or assists in planning tests to evaluate equipment performance. Determines test requirements, equipment modification, and test procedures; conducts tests using all types of instruments; analyzes and evaluates test results, and prepares reports on findings and recommendations.

30086 Engineering Technician VI

Independently plans and accomplishes complete projects or studies of broad scope and complexity. Or serves as an expert in a narrow aspect of a particular field of engineering, e.g., environmental factors affecting electronic engineering. Complexity of assignments typically requires considerable creativity and judgment to devise approaches to accomplish work, resolve design and operational problems, and make decisions in situations where standard engineering methods, procedures, and techniques may not be applicable. Alone, or in a team environment, perform or support installation, testing, verification, repair, diagnostic analysis, and calibration of various systems. Provide organizational, intermediate, and depot level troubleshooting and support of fielded systems. Supervisor or professional engineer provides advice on unusual or controversial problems or policy matters; completed work is reviewed for compliance with overall project objectives. May supervise or train and be assisted by lower level technicians.

Performs, at this level, one or a combination of such typical duties as:

• Prepares designs and specifications for various complex equipment or systems (e.g., a heating system in an office building, or new electronic components such as solid state devices for instrumentation equipment).

• Plans approach to solve design problems; conceives and recommends new design techniques; resolves design problems with contract personnel, and assures compatibility of design with other parts of the system.

• Designs and coordinates test set ups and experiments to prove or disprove the feasibility of preliminary design; uses untried and untested measurement techniques; and improves the performance of the equipment. May advise equipment users on redesign to solve unique operational deficiencies.

• Plans approach and conducts various experiments to develop equipment or systems characterized by (a) difficult performance requirements because of conflicting attributes such as versatility, size, and ease of operation; or (b) unusual combination of techniques or components. Arranges for fabrication of pilot models and determines test procedures and design of special test equipment.

15090 Technical Instructor

Teaches courses in one or more subjects in commercial, governmental, industrial or service establishments. Prepares instructional program in accordance with training or other course requirements, assembling materials to be presented. Instructs students in the theoretical and practical aspects covering the subjects being taught. Utilizes such teaching methods as individual coaching, group discussions, lectures, demonstrations, seminars, and workshops. Selects or develops teaching aids such as wall charts, prepared notes, tape recordings, radio, television, films, film strips, and training handbooks. Supervises practical work carried out by students, and assists them at points of difficulty. Tests students to evaluate their learning progress and to evaluate effectiveness of instruction. Compiles assessment report regarding each student. May arrange visits to or periods of employment in real-work situations to reinforce instruction.

30461 Technical Writer I, 30462 Technical Writer II, and Technical Writer 30463 III

Develops, writes, and edits material for reports, manuals, briefs, proposals, instruction books, catalogs, and related technical and administrative publications concerned with work methods and procedures, and installation, operation, and maintenance of machinery and other equipment.

Receives assignment from supervisor. Observes production, developmental, and experimental activities to determine operating procedure and detail. Interviews production and engineering personnel and reads journals, reports, and other material to become familiar with product technologies and production methods. Reviews manufacturer's and trade catalogs, drawings and other data relative to operation, maintenance, and service of equipment. Studies blueprints, sketches, drawings, parts lists, specifications, mockups, and product samples to integrate and delineate technology, operating procedure, and production sequence and detail. Organizes material and completes writing assignment according to set standards regarding order, clarity, conciseness, style, and terminology. Reviews published materials and recommends revisions or changes in scope, format, content, and methods of reproduction and binding. May maintain records and files of work and revisions. May select photographs, drawings, sketches, diagrams, and charts to illustrate material. May assist in laying out material for publication. May arrange for typing, duplication and distribution of material. May write speeches, articles, and public or employee relations releases. May edit, standardize, or make changes to material prepared by other writers or plant personnel. May specialize in writing material regarding work methods and procedures.

01410 SUPPLY TECHNICIAN

Performs limited aspects of technical supply management work (e.g., inventory management, storage management, cataloging, property utilization) related to depot, local, or other supply activities. Work usually is segregated by commodity area or function, and controlled in terms of difficulty, complexity, or responsibility. Assignments usually relate to stable or standardized segments of technical supply management operations; or to functions or subjects that are narrow in scope or limited in difficulty. The work generally involves individual case problems or supply actions. This work may require consideration of program requirements, together with specific variations in or from standardized guidelines.

Assignments require

• a good working knowledge of the governing supply systems, programs, policies, nomenclature, work methods, manuals, or other established guidelines;

• an understanding of the needs of the organization serviced; and

• Analytical ability to define or recognize the dimension of the problems involved, to collect the necessary data, to establish the facts, and to take or recommend action based upon application or interpretation of established guidelines.

Illustrative Assignments:

1. Inventory management: Responsible for inventory management of decentralized and decontrolled items, including supplies, and equipment. Items managed typically are of low unit or annual demand value, involve short procurement lead time (less than 9 months), are obtained from standard or other readily available sources of supply, and reflect relatively stable patterns of demand. Items usually are of a general, common-use type, nonreparable and seldom require intensive investigation of atypical variations in their supply and demand patterns. Positions are located in local, regional, or headquarters offices for which the military supply management organization has overall inventory management responsibility. The work includes requirements determination and forecasting, distribution or redistribution of material, procurement authorization, limited funds management, or other related work.

2. Material coordination: Performs material coordination duties for special programs, maintenance, or production shops. Duties are performed on the basis of practical experience in processing and expediting supply transactions related to the particular organizations serviced.

3. Cataloging: Writes item descriptions for a range of new items entering the supply channels of a particular agency or field establishment. Applies requirements selecting the appropriate description pattern and answering the requirements contained in the pattern.

Reviews existing stock catalogs, manufacturers' catalogs, drawings, or other resource materials, for the purpose of matching characteristics or part numbers to identify duplicate items already catalogued or otherwise recorded in the supply system.

Level of Responsibility:

1. Works within a framework of established supply regulations, policies, and procedures, or other governing supply management guidelines.

2. Deals with a variety of operating officials regarding limited aspects of program needs of the organization serviced. Contacts may relate to inventory requirements in a stable or standardized organization and to the adequate description or identification of less complex items which are new to the system. May contact representatives of commercial firms to obtain information regarding new items of supply, item characteristics, or procurement lead time; or representatives of government agencies (Federal, State or local) regarding the utilization of property.

14160 PERSONAL COMPUTER SUPPORT TECHNICIAN

The Personal Computer Support Technician provides support to distributed PC/networking environment including installation, testing, repair, and troubleshooting for stand-alone PCs, PCs linked to networks, printers, and other computer peripherals. Support responsibilities include software installation, and configurations. This technician performs technical, operational, and training support to users of personal computers either by telephone, or on-site for PC desktop hardware and software packages. Job duties require the technician to install and test personal computers, printers, and other peripherals, configure operating system, load shrink-wrap programs and other application software programs. In this position, the incumbent troubleshoots computer problems, performs hardware and software diagnostics, coordinates needed repairs, resolves computer system problems, including coordination between users and components of a local area network, and participates in the evaluation of system configuration and software.

14170 SYSTEM SUPPORT SPECIALIST

This position provides troubleshooting assistance and problem resolution for computer systems in a variety of environments. Such assistance and resolution is provided for personal computers, mini/mainframe computers, client-servers as well Local Area Networks (LANs), Wide Area Networks (WANs), and web pages.

Specific ILMS Definitions (non-SCA)

SUBJECT MATTER EXPERT - Provides advanced technical knowledge and analysis of highly specialized applications and operational environment, high-level functional systems analysis, design, integration, documentation, and training. Also provides implementation advice on complex problems that require expert level knowledge of the subject matter for effective implementation. From a computer systems standpoint, participates as needed in all phases of software and hardware development with emphasis on the planning, analysis, testing, integration, documentation, training, and presentation phases.

Education: Baccalaureate Degree in the field of Engineering, Computer Science, or a related discipline, e.g. marine engineering, ship design, from an accredited University. General Experience: Five (5) years C4ISR experience in contract and project management, planning and execution of integrated logistics support management. Specialized Experience: Eight (8) years specialized C4ISR technical experience obtained concurrently with C4ISR Systems requirements development and management.

PROGRAM MANAGER–The Contractor shall provide a Program Manager who shall be responsible for all Contractor work performed under this contract. The Program Manager is further designated as Key Personnel by the Government.

Education: Project Management Professional (PMP) Certified. Specialized Experience: Five

(5) years’ experience in the C4ISR engineering and/or computer industry.

PROJECT TASK MANAGER– Provides project management professional services for smaller projects, providing leadership and is responsible for project direction through successful performance of a variety of detailed, diverse elements of project management tasks. Directs task to completion, ensuring task orders are completed on time and within budget. Schedules and assigns duties to subordinates and ensures assignments are completed as directed. Interfaces with Government representatives and reports to the Program Manager on project progress/status and various issues or problems.

Duties include:

• Program/contract management

• Technical guidance and oversight

• Supervision of design

• Project planning

• Coordination of resources (including subcontractor management)

• Project status reporting

• Document preparation and submission

• Performance measurement and reporting

• Provides product review and quality assurance

Education: Baccalaureate Degree in the field of Business Administration, Engineering, Computer Science, or a related discipline, e.g., marine engineering, ship design, from an accredited University or an advanced technical/trade school degree or certification. Specialized Experience: Four (4) years of maritime and /or facilities project management experience.