Attachment_8_-_First_Article_Inspection_Form_1_V3_(Fit_Test_Part_1).pdf

First Article Inspection Report Form 1: Characteristic Accountability, Verification and Compatibility Evaluation

1. Part Number

N-WMT04X50802001606-00 AKMA or Equivalent Constructed Enclosure

2. Part Name

Enclosure, With-Out Back Panel & Studs, NEMA 4X, Wall Mount, 5086-H32 Aluminum, .80 Thick, 20" H x 16" Width x 6" Depth

3. Serial/Lot Number

N/A

4. FAI Report

FAI-001

Characteristic Accountability Inspection / Test Results Other Fields (Insert columns, as required by organization or customer.

5. Char No.

6. Reference Location 7. Characteristic Designator (Critical, Key)

8.

Requirement

(Dimension, Performance)

8a. UoM 8b.

Upper Limit

8c.

Lower Limit

9. Results (e.g. Pass/1.4 in.

or Failed/1.5 in.

10. Designed Tooling

11. Non- Conformance Number

14. Inspect Device

15. Notes

PC # 1 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 1

Critical 20” Height Inches 0 0 N/A Tape Measure Horizontal measurement of overall exterior enclosure height, top view. Piece # 1 - Enclosure, PC # 1 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 3

Critical 16” Width Inches 0 0 N/A Tape Measure Vertical measurement of overall exterior enclosure width, side view. Piece # 1 - Enclosure.

PC # 1 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 3

Critical 6” Depth

Inches 0 0 N/A Tape Measure Horizontal measure of overall exterior enclosure depth. Piece # 1 - Enclosure.

PC # 2 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 4 and Page 11

Critical 11” Centered Inches 0 0 N/A Calipers/Tape Vertical measurement of 4 exterior aluminum weld pad placements for enclosure mounting.

Piece # 2 – Weld Pad Tap, 3/8”-16 Tap, ¾” DIA x 1-1/2 L.

PC # 2 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 1 and Page 11

Critical 14.625” Centered Inches 0 0 N/A Calipers Horizontal measurement of 4 exterior aluminum weld pad placements for enclosure mounting.

Piece 2 – Weld Pad Tap, 3/8”-16 Tap, ¾” DIA x 1-1/2 L.

PC # 2 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 11

Critical 2.5” Centered

Inches 0 0 N/A Calipers/Tape Vertical measurement of exterior aluminum welds pad placements to top-bottom side wall;

Piece # 2 – Weld Pad Tap, 3/8” – 16 Tap, ¾” DIA x 1-1/2 L.

PC # 2 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 1 and Page 11

Critical 2.6875” Centered Inches 0 0 N/A Calipers Horizontal measurement of exterior aluminum weld pad placements to right-left side wall;

Piece # 2 – Weld Pad Tap, 3/8” – 16 Tap, ¾” DIA x 1-1/2 L.

PC#23 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 10

Key 3” W ide Inches 0 0 N/A Tape Measure Horizontal measurement of overall width of aluminum plate. Piece # 23.

PC#23 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 10

Key 3” Length Inches 0 0 N/A Tape Measure Vertical measurement of overall length of aluminum plate. Piece #23.

PC#23 RFP Attachment 3, Enclosure Requirement – Detailed Drawing, Page 10

Key 1/4 ” Thick Inches 0 0 N/A Tape Measure Thickness measurement of aluminum plate, Piece # 23.

A USCG customer signature and acceptance indicates that all first article characteristics demonstrate the requirements for enclosure full-rate production.

12. Prepared By: 13. Date

14. Report Reviewed by (Quality Representative):

15. Date

16. Customer Approval and Stamp (if applicable):

17. Date

FAI Status:

FAI Acceptable FAI Pending FAI Rejected