SPECIFICATIONS_RFQ_no._70T05018Q9CPA4004_12.06.2017.pdf

RFQ no. 70T05018Q9CPA4004

MINIMUM EQUIPMENT, INSTALLATION AND TECHNICAL SPECIFICATIONS

REQUIREMENTS

a. GRAVITY ROLLER CONVEYOR

CLIN 00001 Gravity Roller Conveyor – Length 3 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00002 Gravity Roller Conveyor – Length 5 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00003 Gravity Roller Conveyor – Length 10 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00004 Kastalon Gravity Roller Conveyor – Length 3 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00005 Kastalon Gravity Roller Conveyor – Length 5 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00006 Kastalon Gravity Roller Conveyor – Length 10 Foot, Width (24, 26, 28, 30, 34, 36 Inches)

*Side frame is 3 ½” high, 10 gauge formed steel, gray powder coat finish, 1.9” diameter, 16-gauge Zinc rollers, 3” axle centers with 7/16” spring loaded hex shaft, sealed bearings (oiled or grease) and rollers set high. Minimum conveyor live load capacity of 300lbs per linear foot.

*Option: Rollers sleeved with Kastalon (or equivalent polyurethane) covers.

*Option: Pop Out Roller.

b. RIGID GRAVITY ROLLER CURVE CONVEYOR

CLIN 00007 Rigid Gravity Roller Conveyor 45o – Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00008 Rigid Gravity Roller Conveyor 90o – Width (24, 26, 28, 30, 34, 36 Inches)

*Same specifications for Gravity Roller Conveyor.

c. SUPPORT LEGS (MS2 - MS7) & GATE SUPPORT LEGS

CLIN 00009 thru 00014 Support Legs (MS-02 – MS07) – Width (24, 26, 28, 30, 34, 36 Inches)

CLIN 00015 thru 00020 Gate Support Legs (RS-02 – RS-07) – Width (24, 26, 28, 30, 34, 36 Inches)

*Heavy duty all bolted construction stationary “H” stand floor supports constructed of 11-gauge or better steel with gray powder coat finish, with support feet suitable for floor bolting or adhesive attachment.

*Support Legs must allow minimum 16” top of roller, maximum 40” top of roller. Leg height with eight 8” caster would be minimum 16” top of roller to 32” top of roller.

*Leg height adjustment: 16” to 40” including support feet.

d. GRAVITY ROLLER LIFT GATE

CLIN 00021 Gravity Roller Gate – Length 3 Foot, Width (24, 26, 28, 30, 34 and 36 Inches)

CLIN 00022 Gravity Roller Gate – Length 4 Foot, Width (24, 26, 28, 30, 34 and 36 Inches)

*Pneumatic or spring loaded assist lift gate with adjustable springs or gas charged weight compensating cylinders designed to be connected to a heavy-duty rigid gravity roller conveyor, frame 3 ½” deep, all bolted construction of 10-gauge steel with gray powder coat finish. Lift gate shall lock at vertical position and be releasable from either side. Handles shall be located on each side and be designed to avoid catching baggage straps. Pinch points shall be guarded and all metal edges rounded or installed with frame guards. Minimum conveyor live load capacity of 300lbs per linear foot.

e. FLEXIBLE ROLLER CONVEYOR

CLIN 00023 Flexible Roller Conveyor – Length 8 Foot, Width (24 and 30 Inches) CLIN 00024 Flexible Roller Conveyor – Length 14 Foot, Width (24 and 30 Inches)

*Heavy duty flexible roller conveyor with quick conveyor connector (connects to another flexible roller conveyor) and modular, all bolted construction.

*Minimum fully extended live load weight capacity of 200lbs per linear foot. Heavy-duty stainless steel, durable rubber or epoxy coated steel rollers suitable for application and load characteristics. Rollers to be 1 ⅜ to 2" in diameter with 3” axle centers (fully extended), sealed ball bearings, spring loaded axles and 16-gauge or better steel and installed set high.

*Heavy duty casters 5" by one and 1 ¼" with swivel and wheel lock pedal brakes on all casters and steel axles appropriate for roller bed weight capacity. Height adjustment from 16" to 40" including caster height. Connecting brackets constructed of 11-gauge steel or better with hand knob sets and lock washers to allow secure and permanent connection without the use of tools. Both sides of the conveyor are to operate independently across the connections.

*Heavy-duty upper leg and inner legs constructed of at least 14-gauge or better steel, with cross braces and connections to roller axles suitable for application and load characteristics.

*Handles or knobs for adjusting heights at conveyor ends shall be attached such that they do not prevent the conveyor from being installed close to other equipment.

*8’ Flexible conveyor shall be nominally 4' compressed and 8' extended.

*14’ Flexible conveyor shall be nominally 8' compressed and 14' extended.

f. BALL TRANSFER TABLE (BTT) WITH COVER PLATE

CLIN 00025 Ball Transfer Table – 30 Inches x 30 Inches

CLIN 00026 Ball Transfer Table – 36 Inches x 36 Inches

*Frame shall be 3 ½” high with 10-gauge steel with gray powder coat finish. Bolt on couplers are required at each connecting point with rigid conveyor. Therefore, ball transfer table must have the capability to bolt to connecting conveyors on all four sides. Bolt-on couplers must be compatible with rigid gravity roller conveyors.

*Ball diameter is 1”, square pattern with 2” centers. Ball and housing profile to be low profile with working height of ball (top of ball to table top) no more than one 1”. Ball exposure to be a minimum of 1/4”.

*Steel or aluminum cover plate providing working height of ball no more than one inch (1”) and ball exposure to be at least one quarter (1/4”) above the cover plate.

PERIPHERALS:

g. HAND OPERATED BLADE/ROLLER STOP

CLIN 00027

*Heavy duty, hand operated, 2” high stop, constructed of 12-gauge or better steel, extending across the full width between conveyor frames which can be installed at the end of the last continuous conveyor section and folds down when not in use.

h. RECTANGLE CONVEYOR GUARDS

CLIN 00028 *3 Foot section to fit gravity roller conveyor side frame.

CLIN 00029 *5 Foot section to fit gravity roller conveyor side frame.

*Gray, padded polystyrene rail guard that snaps on the conveyor steel side frame.

i. STRAIGHT GUARD RAIL

CLIN 00030 *3-Foot-High Straight Guard Rail Long CLIN 00031 *5-Foot-High Straight Guard Rail Long CLIN 00032 *10-Foot-High Straight Guard Rail Long

*Removable, 3 ½” high, fixed, 12-gauge, gray powder coat finish, “C” channel in 3’, 5’ and 10’ lengths with rounded corners and edges or padding to protect personnel and baggage.

j. CURVED GUARD RAIL

CLIN 00033 3-Foot-High Curved Guard Rail 45 Deg-Outside CLIN 00034 3-Foot-High Curved Guard Rail 90 Deg-Outside

*Removable, 3 ½” high, fixed, 12-gauge, gray powder coat finish to match length of outer curves of 45 and 90 degree curved roller conveyors with rounded corners and edges or padding to protect personnel and baggage.

k. TERMINATING END STOP

CLIN 00035 *Bolts to top flange of conveyor channels at the end of conveyor. Width (24, 26, 28, 30, 34, 36 Inches).

l. EDGE TRIM

CLIN 00036 *10’, Single Gripping Finger, Black, PVC/Metal Edge Trim.

Overall Height: 0.50” Overall Width: 0.375” Leg Length: 0.438

Fits Edge: 0.188”

m. 6” TURNING WHEEL

CLIN 00037 *6” wheel mounted on adjustable bracket on side channels of gravity conveyors.

n. END CAPS

CLIN 00038 *Flexible, black rubber, 3 ½” x 1 ½” x 1” rectangular cap to fit over sharp edges at the end of conveyor rail.

o. Pop Out Roller Option

CLIN 00039 Fitted roller shaft that rests in notches on either side of the conveyor framework as a safety feature.

p. SHIPPING

CLIN 00040 Special Shipping