662-23-105_Equipment Cutbook 1 of 2-min.pdf

NOMENCLATURE Extinguisher,Fire JSN A1000

Acq/Ins V / V - Government Furnished, Government Installed Weight (lbs) 19 Weight (kg) 9

Height (in) 22 Height (cm) 56

Width (in) 6 Width (cm) 15

Depth (in) 6 Depth (cm) 15

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description 10 pound dry chemical fire extinguisher with charging gauge. Other types and sizes are available.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop and coordinate the design/construction in accordance with actual equipment selection.

Kidde Residential and Commercial Division 1016 Corporate Park Drive, Mebane, NC 27302

(800) 880-6788 www.Kidde.com

Description

Suitable for use on Class A (trash, wood & paper), Class B (liquids & gases) and Class C fires (energized electrical equipment).

The Pro 10 MP unit is fitted with a pressure gauge that provides at-a-glance status, cylinder is manufactured from impact resistant steel and the valve assembly is all metal.

Pro 10 MP Fire Extinguisher

At a Glance

common fires

Multipurpose use

Net agent weight (Average) 10 lb.

Unit weight (Average) 16 lb.

Diameter 5.21 inches

Height 19.52 inches

Discharge time 19-21 seconds

Discharge range 20 feet

Operating pressure 195 psi

Cylinder Mild steel

Valve, handle, lever Metal

Strap Bracket (not supplied) U.S.C.G approved

For use on the following types of fire:

Rechargeable

Product Specification

Features

Packaging Options

Part number 466204

UL Rated 4-A, 60-B:C

Y

EAR LIMITED

W

A R R A N T

Y

F

IR

E EXTINGUIS

H E

R

R E C H A R G E A B L E

Depth Width Height

Carton 5.37 6.62 19.5

Packaging dimensions (inches)

SHIPPED IN CARTON

Pt # 466204 - 1 pack

UPC: 0-47871-66204-3

I2F - 20047871662047

A1000

NOMENCLATURE Telephone,Wall Mounted,1 Line,With Speaker JSN A1014

Weight (lbs) 0 Weight (kg) 0

Height (in) 0 Height (cm) 0

Width (in) 0 Width (cm) 0

Depth (in) 0 Depth (cm) 0

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc T | CAT 6 to nearest T-Comm Room

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description Telephone, wall mounted, 1 line, with speaker.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

NOMENCLATURE Telephone,Desk,Multiple Line JSN A1015

Weight (lbs) 0 Weight (kg) 0

Height (in) 0 Height (cm) 0

Width (in) 0 Width (cm) 0

Depth (in) 0 Depth (cm) 0

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc T | CAT 6 to nearest T-Comm Room

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description Telephone, desk, multiple line.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

NOMENCLATURE Mirror,Float Glass,ADA Accessible JSN A1067

Acq/Ins C / C - Contractor Furnished, Contractor Installed Weight (lbs) 20 Weight (kg) 9

Height (in) 37 Height (cm) 94

Width (in) 18 Width (cm) 46

Depth (in) 6 Depth (cm) 15

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description A high quality 1/4" polished float glass mirror with a stainless steel frame. Frame holds mirror in a tilted position for accessibility and compliance with ADA requirements. Mirror has a galvanized steel back secured to frame with concealed screws with integral horizontal hanging brackets. Mirror shall be approximately 18" wide and 36" high. Other sizes are available.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Fixed Tilt Mirror

© 2020 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

800 BRADLEY (800 272 3539) +1 262 251 6000

bradleycorp.com

Orders composed of products indicated as Bradex® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

Page 1 of 2 11/11/2020 This information is subject to change without notice.

Bradley_Mirror_740

View Latest Version

Fix tilt mirror with welded corners:

Standard Model 740-1830 (18" x 30") Bradex®

Standard Model 740-1836 (18" x 36") Bradex®

Standard Model 740-2436 (24" x 36") Bradex®

Model 740-XXXX (Specify width and height)

Product Materials FRAME: 20 gauge stainless steel, corners welded and ground smooth to satin finish. 20 gauge angle stiffeners welded to frame provide additional rigidity.

BACK: galvanized steel, secured to frame with concealed screws equipped with integral horizontal hanging brackets.

MIRROR: first quality ¼" float glass, thermosetting infrared-cured paint backing with Poly-Glaze protective finish. Manufactured in accordance with ASTM C 1036 and ASTM C 1503. The back of the mirror is protected by a wedge of extruded polystyrene, which is placed between the mirror and the galvanized steel.

WALL HANGER: 18 gauge cold-rolled steel, all welded construction to form rigid template.

Optional Features Features Suffix

¼" tempered glass mirror in lieu of polished float glass mirror* -2

Laminate glass -3

Highly polished No. 8 architectural finish, 20 gauge stainless steel in lieu of polished float glass mirror

-4

Bright annealed 20 gauge stainless steel in lieu of polished float glass mirror

-5

Plexiglas® -6

*�Either the Length (L) or the Width (W) must be greater than 25".

�An inherent characteristic of a manufacturing process for tempered glass is distortion which may vary from mirror to mirror.

�Stainless steel mirrors will differ in optic quality from glass mirrors.

�In larger sizes, stainless mirrors are subject to distortion and/or "oil canning" for which Bradley Corporation cannot accept responsibility.

Bradley mirrors are not field interchangeable from horizontal to vertical or vice versa.

Always specify width first.

Installation Verify all rough-in dimensions prior to installation. Secure concealed mounting bracket to wall with screws (not included) at holes provided. Provide in-wall backing at mounting screw locations. Position mirror over mounting bracket to engage hanger tabs. Slide mirror down and lock into position.

Guide Specification Fixed tilt mirror shall be framed with 20 gauge stainless steel with 20 gauge concealed stiffeners. Welded corners shall be polished to a uniform satin finish. Mirror shall be of first quality ¼" float glass guaranteed for 15 years against silver spoilage and protected by a shock-absorbing, waterproof foam filler with Poly-Glaze protective finish. Back of unit shall be galvanized steel secured to frame with concealed screws, equipped with integral horizontal hanging brackets and separate wall hanger for concealed mounting.

Fixed Tilt Framed Mirror shall be Bradley Model 740-______" W x______" H (specify width and height).

ADA Compliant �Consult local and national accessibility codes for proper installation guidelines.

� �Conformity and compliance to local and national codes is the responsibility of the installer.

A1067 david.reid Highlight

Fixed Tilt Mirror

© 2020 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

800 BRADLEY (800 272 3539) +1 262 251 6000

bradleycorp.com

Orders composed of products indicated as Bradex® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

Page 2 of 2 11/11/2020 This information is subject to change without notice.

Bradley_Mirror_740

View Latest Version

6°

Dimensions

Dim. "A" to finished floor

Dim. "A" Key Surface:

For Dim. "A" Bottom of Unit

Mirror's bottom edge of the reflecting surface to finished floor

40" (1016mm) 39¼" (997mm)

37" (940mm) 36¼" (921mm)

34" (864mm) 33¼" (845mm)

Rough wall opening:

Surface Mount: No rough wall opening, see overall dimensions

Bradex® Models Width

(Inches) W

Height (Inches)

H

Overall Dimension (Inches)

Overall Dimensions (Millimeters)

Standard Model

Number

18" 30" 18 x 30 457 x 762 740-1830

18" 36" 18 x 36 457 x 914 740-1836

24" 36" 24 x 36 610 x 914 740-2436

Model 740 series angle framed mirrors can be fabricated to a maximum size of 48"W x 48"H.

“H”

1" (25mm)

“W”

“H” Hanger

Outer edge of mirror

4" (102mm)

2¼" (57mm)

Mounting Screw

Locations

3¹⁄₈" (79mm)

3¹⁄₈" (79mm)

A1067 david.reid Highlight

NOMENCLATURE Mirror,Posture,Wall Mounted JSN A1080

Weight (lbs) 60 Weight (kg) 27

Height (in) 72 Height (cm) 183

Width (in) 28 Width (cm) 71

Depth (in) 4 Depth (cm) 10

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description Wall mounted posture mirror. Consists of a 1/4" plate glass in a sturdy corrosion resistant frame with water proof back. For educational and therapy programs.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

THERAPY AND REHAB EQUIPMENT

C. Model

B. Model

A. Model

A. Model 1670 Portable Triple Mirror

MODEL WIDTH DEPTH HEIGHT

1670 60”(open) 24”(open) 69”

B. Model 1671 Portable Single Mirror

MODEL WIDTH DEPTH HEIGHT

1671 24” 18” 70”

C. Model 1672 Wall Mounted Mirror

MODEL WIDTH DEPTH HEIGHT

1672 24” 4” 66”

D. Model S-410 Front View

E. Model S-420 Reverse view

D. Model S-410 Econo Mirror

⁄2

MODEL WIDTH DEPTH HEIGHT

S-410 24” 18” 70”

E. Model S-420 Econo Mirror Rack

MODEL WIDTH DEPTH HEIGHT

S-420 24” 18” 70”

Model S-420-100 Accessorized Mirror Rack

MODEL CONSISTS OF

S-420-100 (1) S-420 mirror, (1) 5581 Set of

(16) Hugger Weights

All weights shown must be ordered as accessories

A1080 david.reid Rectangle

Line

NOMENCLATURE Counter,Cleanup,With 2 or 3 Sinks JSN A1195

Acq/Ins V / C - Government Furnished, Contractor Installed Weight (lbs) 490 Weight (kg) 222

Height (in) 53 Height (cm) 135

Width (in) 98 Width (cm) 249

Depth (in) 30 Depth (cm) 76

Utility 1: Plumbing F | Cold, hot and treated water and drain

Utility 2: Electrical B | 120 volt, special outlet

Utility 3: Med Gas C | Air, low pressure (30 PSIG) max

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 1

AMPS 3

VOLTS 120

HERTZ 0

BTU / HR 0

WATTS 0

Description Two or three sink cleanup counter. Unit is constructed of type 304 corrosion resistant stainless steel. It consists of three sinks 14"W X 16"H X 10"D, hot and cold water faucet, and pre-rinse spray hose. Equipped with channel reinforced drainboards, and backsplash, and supported by tubular stainless steel legs. Unit is designed for use in control sterile supply decontamination areas.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

One Integrated Approach to Healthcare.

Sterile Processing Services

AMSCO Reprocessing Sinks’ innovative designs promote best practices

– delivering an improved process, a streamlined workflow and consistent outcomes.

AMSCO® 30, 50 and 70 Series Reprocessing Sinks

COMPLIANT & CONSISTENT

FROM THE START

Meeting the evolving standards of healthcare does not have to mean compromising efficiency or complicating processes.

A1195

Give yourself enough room to properly clean large devices without damage with 30” bays**

Larger Bays

Make every drop of chemistry count through the AMSCO 70 Series Reprocessing Sink’s integrated temperature monitoring and automated dosing. Get peak performance from enzymatics and ensure the precise dose is delivered… every time.*

*Based on Regular PMs & Calibration Schedules **AMSCO 50 and 30 Series Reprocessing Sinks only

Manual cleaning can be one of the most cumbersome and variable steps in reprocessing. Helping to ensure you maintain compliance both through process and audit, the AMSCO Reprocessing Sinks make meeting the current ANSI/AAMI standards* seamless.

Start driving best practices from the beginning

COMPLIANCE

Automated Degas Cycle

Documentation

ANSI/AAMI

COMPLIANT

ST79

Encourages best practice after the manual washing process for consistent performance of ultrasonic activity

Temperature Monitoring and Automated Dosing

Instilling confidence, accuracy and safety, AMSCO Reprocessing Sinks help your CSSD run efficiently - allowing staff to focus on the critical step of manually cleaning instruments.

CONSISTENCY THAT

OPTIMIZES WORKFLOW

Making every space count – FlexPlates allow technicians to expand the surface area of their workspace

Maximizes Space

Counter height adjusts from 33-41”

Magnetized backsplash allows for organization and accessibility-allowing for placement anywhere on the backsplash - convenient for each technician

Convenient & Organized

Meeting the ergonomic challenges of a diverse workforce, and helping reduce the risk of work related injuries, the height adjustment feature makes the AMSCO 50 and 70 Series Reprocessing Sinks the ideal workstation.

Ergonomic

The intuitive icon-driven interface of the AMSCO 70 Series Reprocessing Sink provides confirmation of the current step being performed – while still allowing the flexibility to use other bays.

Ease of Use

AMSCO 50 Reprocessing Sink

AMSCO 30 and 50 Series Reprocessing Sinks

BIG PERFORMANCE, BIG VALUE

SKU Length Number of Bays

SINK3077 77" 2

SINK3096 96" 2

SINK3097 97.5" 3

SINK30106 106" 3

SINK30120 120" 3

SKU Length Number of Bays

SINK5077 77" 2

SINK5096 96" 2

SINK5097 97.5" 3

SINK50106 106" 3

SINK50120 120" 3

AMSCO 30 Reprocessing Sink AMSCO 50 Reprocessing Sink

The AMSCO 70 Series Reprocessing Sink can be configured to help comply with the latest standards while meeting your space, volume and budget demands.

AMSCO 70 Series Reprocessing Sink

SOLUTIONS TO FIT YOUR

WORKFLOW

Dual Bay

SKU Length Right to Left Workflow

SW01201 80" Wash, Aqua Klenz

SW01402 80" Rinse, Wash

SW01302 80" Sonic Klenz, Wash

SW02201 94" Wash, Aqua Klenz

SW02402 94" Rinse, Wash

SW02302 94" Sonic Klenz, Wash

SKU Length Left to Right Workflow

SW01102 80" Aqua Klenz, Wash

SW01204 80" Wash, Rinse

SW01203 80" Wash, Sonic Klenz

SW02102 94" Aqua Klenz, Wash

SW02204 94" Wash, Rinse

SW02203 94" Wash, Sonic Klenz

SKU Length Right to Left Workflow

SW03421 106" Rinse, Wash, Aqua Klenz

SW03422 106" Rinse, Wash, Wash

SW03342 106" Sonic Klenz, Rinse, Wash

SW04421 120" Rinse, Wash, Aqua Klenz

SW04422 120" Rinse, Wash, Wash

SW04342 120" Sonic Klenz, Rinse, Wash

Triple Bay

SKU Length Left to Right Workflow

SW03124 106" Aqua Klenz, Wash, Rinse

SW03224 106" Wash, Wash, Rinse

SW03243 106" Wash, Rinse, Sonic Klenz

SW04124 120" Aqua Klenz, Wash, Rinse

SW04224 120" Wash, Wash, Rinse

SW04243 120" Wash, Rinse, Sonic Klenz

A1195 cphillips Rectangle cphillips Line cphillips Line cphillips Line cphillips

M9466EN.2018-04 Rev. A ©2018 STERIS Corporation.

All rights reserved.

For more information please contact your STERIS representative or visit STERIS.com/DecontaminationSinks

SINK FEATURES COMPARISON

Temperature Monitoring

Automated Chemistry

Dosing

Sonic Klenz Bay

Flex Plates

Electric Height

Adjustment

Magnetic Back

Splash

30" Bays

Air Pistol

Water Pistol

Etched Gallon

Markings AMSCO 70 Series Reprocessing Sink

X X X X X X X X X

AMSCO 50 Series Reprocessing Sink

Optional X X X X X X

AMSCO 30 Series Reprocessing Sink

Optional X X X X X

3X 30 [762]

BASIN

17 [432]

BASIN

97-1/2 [2477]

UNIT WIDTH

33 [838]

MINIMUM

WORKING

HEIGHT

41 [1041]

MAXIMUM

WORKING

HEIGHT

28-1/16 [712]

UNIT DEPTH

7/8 [22]MIN

SEE NOTE #2

23-1/16 [585]

DRAIN BOARD 3/4 MAX

[19]

28-15/16 [734]

MINIMUM

52-9/16 [1335]

MAXIMUM

HEIGHT

4 [102]

BACKSPLASH

11-9/16 [293]

BACKSPLASH

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.022 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

REVISION: ECN #:

REVISION HISTORY DEPICTS CHANGES FROM

PRIOR REVISIONF 106432

INDEX DESCRIPTION OF CHANGE

1 ADD 2" COPPER P-TRAP AS ACCESSORY UNDER UTILITY REQUIREMENTS ALONG WITH ESTIMATED DRAIN RATE 2 SHEET 3- CHANGED UTILITY REQUIREMENTS FROM 1/2" NPSM TO 3/8" COMPRESSION (2 PLACES) 3 SHEET 3- CHANGED UTILITY REQUIREMENTS FROM QUICK CONNECTOR FLEX COIL TO 3/8" COMPRESSION 4 SHEET 3- CHANGED UTILITY REQUIREMENTS FROM 1/2" NPSM WITH ...ADAPTER (INCLUDED)C TO 1/2" NPT

5 SHEET 3- CHANGED UTILITY REQUIREMENTS FROM 1/4" NPFT HOSE INCLUDED TO 1/4" NPT

6 SHEET 3- CHANGED NOTE 5 FROM "PREVENTED" TO "PREVENTION"

7 SHEET 4- CHANGED WALL AND FLOOR VIEW DRAIN DETAILS AND NOTES

8 SHEET 4- MOVED SEISMIC ANCHOR VIEW TO SHEET 6

9 SHEET 6- ADDED NOTE 2

DETAIL A

NOTES:

1. UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE IN INCHES [MM].

2. INSTALLER MUST MAINTAIN A MINIMUM GAP OF .875" TO ALL ADJACENT WALLS AS PINCH POINT PROTECTION.

3. UNIT TO BE INSTALLED AGAINST A WALL, FOR BACK TO BACK INSTALLATION A PONY WALL IS REQUIRED.

4. 304 SERIES STAINLESS STEEL CONSTRUCTION.

5. PONY WALL HEIGHT MUST BE 53"[1346].

6. WALL MUST BE FREE OF OBSTRUCTIONS TO 54"[1372].

TOP VIEW

BASIN DEPTH 10" [254]

ADJUSTABLE HEIGHT FEET (4)

FRONT VIEW

DETAIL A RIGHT SIDE VIEW

SHOWN AT

MAX HEIGHTF

17-3/4 [451]PW

29-1/4 [743]HW

37-1/4 [946]CW

45 [1143]A

52-1/2 [1334]WG

60-1/4 [1530]HW

68-1/4 [1734]CW

79-3/4 [2026]PW

27 [686]

6-3/8 [162]

13-1/2 [343]

75 [1905]

SUPPLY CONNECTIONS

TO BE IN THIS ZONE

11-1/8 [282]

MAXIMUM

80-3/4 [2051]

MINIMUM

72-3/4 [1848]

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.016 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

HW HOT WATER

CW COLD WATER

PW PURE WATER

WG WATER GUN

A COMPRESSED AIR

DB DRAIN BASKET (BASIN)

D DRAIN

NOTE: WORKFLOW CAN BE REVERSED BY MOVING PURE WATER FAUCET

FROM RIGHT SIDE TO HOLE ON LEFT THAT IS CAPPED.

ADDITIONALLY THE COMPRESSED AIR AND WATER GUN FIXTURES SHOULD BE SWAPPED.

RIGHT SIDE VIEW

SHOWN AT

MAX HEIGHT

FRONT VIEW

DB

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.016 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

ADJ. HEIGHT PROCESSING TRIPLE SINK 97.5" X 28" X 33"-41"

UTILITY REQUIREMENTS CHART (PLUMBING)

UTILITY PARAMETER REQUIREMENT NOTES

HOT WATER

(HW)

CONNECTION TYPE/SIZE 3/8" COMPRESSION

PRESSURE RANGE 15 TO 125 PSI

OPERATING FLOW RATE 1.6 GPM @ MAX PSI

TEMPERATURE RANGE 40 TO 180 F

WATER QUALITY SEE NOTE #2

COLD WATER

(CW)

CONNECTION TYPE/SIZE 3/8" COMPRESSION

PRESSURE RANGE 15 TO 125 PSI

OPERATING FLOW RATE 1.6 GPM @ MAX PSI

TEMPERATURE RANGE 70 F MAX

WATER QUALITY SEE NOTE #2

PURE WATER

(PW)

CONNECTION TYPE/SIZE 1/2" NPT

PRESSURE RANGE 20 TO 125 PSI

OPERATING FLOW RATE .25 TO 2.00 GPM ±15%

TEMPERATURE RANGE 40° F TO 140°F

WATER QUALITY

WATER GUN

(WG)

CONNECTION TYPE/SIZE 3/8" COMPRESSION

PRESSURE RANGE 0 TO 44 PSI

OPERATING FLOW RATE

TEMPERATURE RANGE 40° F TO 125°F

WATER QUALITY SEE NOTE #2

AIR GUN

(A)

CONNECTION TYPE/SIZE 1/4" NPT CONNECTION MUST BE MADE

PER LOCAL CODE

PRESSURE 30 PSI MAX

TIP 1

CONSUMPTION AT 30 PSI 2 SCFM

TIP 2

TIP 3

TIP 4

TIP 5

TIPS 4 & 5 MUST BE OPERATED AT 30 PSI OR LESS TO COMPLY WITH OSHA DIRECTIVE

BASIN DRAIN

(BD) CONNECTION TYPE

1-1/2" ABS P-TRAP (INCLUDED)

2" COPPER P-TRAP (ACCESSORY)

DRAIN RATE AT 20 GPM

EACH BASIN (ESTIMATED)

NOTES:

1. SUPPLY LINES FOR EACH CONNECTION ARE SHIPPED WITH EACH SINK.

2. STERIS RECOMMENDS THE FOLLOWING WATER QUALITY PARAMETERS:

1. 100-200 PPM (500PPM MAX) TOTAL DISOLVED SOLIDS.

2. 70-120 PPM (180PPM MAX) TOTAL ALKALINITY.

3. 6.8-7.0PH (7.5 MAX).

4. 0.1-0.5PPM (1.0PPM MAX) TOTAL SILICA.

3. STERIS DOES NOT SUPPLY A PRESSURE REGULATOR FOR USE WITH AIR GUN.

4. STERIS DOES NOT SUPPLY A PRESSURE REDUCING VALVE FOR USE WITH WATER GUN.

5. BACK FLOW PREVENTION BY CUSTOMER AGAINST BACK SIPHONAGE MAY BE REQUIRED (CHECK LOCAL PLUMBING CODE).

6. FLOOR SINK OUTLET NEEDS TO BE ABLE TO ACCOMODATE WASTE FROM ALL BAYS (CHECK LOCAL PLUMBING CODE).

7. REFERENCES FOR PARAMETERS ARE TO MANUFACTURER'S RECOMMENDATION AND SHOULD BE FOLLOWED ACCORDINGLY.

F

F

F

F

F

17-15/16 [455]

17-15/16 [455]

[787]

CENTER TO CENTER

DRAIN LOCATION

[787]

CENTER TO CENTER

DRAIN LOCATION

9-3/8 [238]

WALL CONNECTION

HEIGHT FROM FLOOR

[152]

65-3/8 [1662]

[153]

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.016 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

FLOOR NOTES:

1. FLOOR DRAIN IS PREFERED.

2. DRAIN CANNOT BE LOCATED WITHIN 6" OF LEGS.

FRONT VIEW

FRONT VIEW

DRAIN LOCATION, (FLOOR)

FLOOR DRAIN CONNECTIONS

TO BE IN THIS ZONE

DRAIN ℄

RIGHT SIDE VIEW

SHOWN AT

MAX HEIGHT

WALL NOTES:

1. EACH DRAIN INDIVIDUALLY TRAPPED.

2. WHEN TRAPS ARE NOT REQUIRED, ELBOWS CAN BE PURCHASED LOCALLY.

3. ROUGH-IN TOLERANCE ±3/8"

DRAIN LOCATION, (WALL)

RIGHT SIDE VIEW

SHOWN AT

MAX HEIGHT

DRAIN ℄

F

F

F

[483]

[152]

[76]

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.022 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

ADJ. HEIGHT REPROCESSING TRIPLE SINK 97.5" X 28" X 33" TO 41"

UTILITY SPECIFICATIONS CHART (ELECTRICAL)

ELECTRICITY

UTILITY PARAMETER REQUIREMENT NOTES

ELECTRICITY 120V 15A GFCI PROTECTED OUTLET

LINAK DL2 LIFT SYSTEM

LINAK DL2

LIFT SYSTEM

WEIGHT CAPACITY 562LBS [2500 N] EACH

ADJUSTMENT RANGE 8.0" [203,2]

LIFT SPEED UP TO 3/8"[10] PER SECOND

VOLTAGE 120VAC, 3A WITH OVERLOAD

PROTECTION

PARTIAL FRONT VIEW

UTILITY (ELECTRICITY)

CONNECTION POSITION

RECOMMENDED

INCLUDES 10'[3048] CORD

15A 120VAC GFCI

PROTECTED OUTLET

1-1/2 [38]

14 [356]

SEE NOTE BELOW

⌀9/16 [14]

FOR 1/2-13

SEISMIC ANCHORS

102-7/16 [2602]

SEE NOTE BELOW

95-1/16 [2415]

6-13/16 [173]

[406]

[762]

TOLERANCES: +/- INCH (MM) IF NOT INDICATED OTHERWISE MATERIAL / NOTES

DIMENSION 0-48 48+ DIMENSION 0-4 4-24 24+

NA

FINISH: NA

MACHINING FRAC.

DEC.

1/64 0.005

1/32 0.015

PLASTIC FRAC.

DEC.

1/64 0.005

1/32 0.020

1/16 N/A

SHEET METAL / SAWING 1/32 1/16 DIMENSION 0-12 12-60 60+ COMPONENT/ASSEMBLY MUST BE RoHS COMPLIANT

DIMENSION 0-1 1+ WELDED ASSEMBLY 1/32 1/16 3/32 DIMENSION 0-3/8 3/8-3/4 3/4 +

BORING 0.001 0.002 SPOT WELD 1/16 3/32 HOLE DIAMETER 0.005 0.015 1/32

SURFACE FINISH 63 machined surface (Visual) SQUARENESS 1/16 total 1/8 total ANGLE 1° WEIGHT: [.2] LBS.

T I T L E

3 BASIN 97.5" ADJUSTABLE HEIGHT REPROCESS SINK

Corporation

SIZE: SCALE: DRAWN BY: DRAWING NUMBER: PART NUMBER: REVISION:

A 0.022 Kosir, Joe SINK5097 F.3 11002999 F

This document contains confidential and proprietary information of STERIS Corporation. Neither this document nor the information herein are to be reproduced, either in part or in whole, except as specifically authorized by STERIS Corporation.

SHEET

PHYSICAL SPECIFICATIONS

SHIPPING DIMENSIONS L X W X H 132L X 36W X 48H

SHIPPING WEIGHT 580 LBS

OPERATING DIMENSIONS L X W X H 97.5" X 28" X 44-9/16" TO 52-9/16"

[2477 X 711 X 1132 TO 1412]

OPERATING WEIGHT EMPTY 380 LBS

WORKING HEIGHT 33"[838] TO 41"[1041]

NOTE:

1. CONCRETE FLOOR MUST REMAIN FREE OF DEFECTS IN THESE AREAS FOR

INSTALLATION OF SEISMIC ANCHORS (NOT PROVIDED BY STERIS).

2. REFER TO EQUIPMENT SPECIFIC SEISMIC DRAWING FOR MORE INFORMATION.

SEISMIC ANCHOR HOLE POSITIONS

SCALE 0.050

BACK WALL

NOMENCLATURE Bench,Locker Room,Portable JSN A5025

Weight (lbs) 45 Weight (kg) 20

Height (in) 18 Height (cm) 46

Width (in) 96 Width (cm) 244

Depth (in) 15 Depth (cm) 38

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description Portable locker room bench. Approximately 1-1/2" thick. Benches shall be laminated hardwood with a moisture resistant sealer or anodized aluminum Units are mounted on strong pedestals.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Locker Bench Hardwood Top w/Steel Trapezoid Pedestals, Bolt Down Style, 72"W x 9-1/2"D x 17"H

Item #: WG184992

Product Information

Locker Bench Hardwood Top w/Steel Trapezoid Pedestals, Bolt Down Style, 72"W x 9-1/2"D x 17"H

Extra convenience in the locker room. 1-1/4" thick hardwood bench features a heavily varnished top and sturdy stainless steel base.

Trapezoid stainless steel 14"W base. Must be anchored to floor for maximum stability. Bench has two pedestals.

A5025 https://www.globalindustrial.com/

Product Specifications

WIDTH INCHES 72

DEPTH INCHES 9-1/2

HEIGHT INCHES 17

ASSEMBLY Unassembled BRAND Global Industrial COLOR FAMILY Tan COLOR FINISH Maple Top/Gray Pedestals CONSTRUCTION Hardwood Maple Top/Stainless Steel Pedestals PRODUCT FAMILY Accessories STYLE Trapezoid

THICKNESS INCHES 1-1/4

TYPE Locker Bench LIMITED WARRANTY 1 Year accessory_type Locker Bench

Photo Gallery

Customer Reviews

Avg. Review Rating: 1 reviews

Reviewed On: August 24, 2016

NOMENCLATURE Bench,Stall,Shower,Built In JSN A5030

Weight (lbs) 26 Weight (kg) 12

Height (in) 12 Height (cm) 30

Width (in) 35 Width (cm) 89

Depth (in) 22 Depth (cm) 56

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description Shower bench; built-in. Eighteen (18) gauge stainless steel frame with anchors built-in into the wall.

Size and shape as required.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

1-877-947-7769 FreedomShowers.com

APF

APF

A5030

A5030

NOMENCLATURE Dispenser,Soap,Disposable JSN A5075

Weight (lbs) 2 Weight (kg) 1

Height (in) 11 Height (cm) 28

Width (in) 5 Width (cm) 13

Depth (in) 4 Depth (cm) 10

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ

BTU / HR 0

WATTS 0

Description Disposable soap dispenser. One-handed dispensing operation. Designed to accommodate disposable soap cartridge and valve.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Skin Care Dispenser

Scott® Essential Manual Skin Care Dispenser, 1.0 Liter

Product Codes:

92144 White

92145 Black

®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses sociétés affiliées. © KCWW. T9EFD9

• Made of ABS plastic with view window on front

• Accommodates a 1.0-liter sealed skin cleanser, hand sanitizer, body wash, or lotion manual cassette that easily snaps into place

• Easy loading

• Compatibility with universal mounting brackets and wall and floor protectors

• Push-button latch

• Hardware included for mounting

• One per case

Form # 034128

Suggested mounting height is 48” from the floor or 12” above a counter to the bottom of the dispenser.

�When installed properly and used with the corresponding product, this dispenser meets ADA Standard 28 CFR Part 36, local rules may vary.

5.43”

4.85”

8.36”

3.62” 2.50”

8.36”

4.85” 2.50”

6.38”

.38”

.50”

.50”

A5075

NOMENCLATURE Dispenser,Hand Sanitizer,Hands-Free JSN A5077

Weight (lbs) 2 Weight (kg) 1

Height (in) 15 Height (cm) 38

Width (in) 7 Width (cm) 18

Depth (in) 6 Depth (cm) 15

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description A touch free wall-mounted hand sanitizer dispenser. For use throughout a healthcare facility. Unit does not include the sanitizing liquid. Units are battery operated.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Skin Care Dispensers

Scott® Essential Electronic Skin Care Dispenser,

1.2 Liter

92147 White

92148 Black

®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses sociétés affiliées. © KCWW. T9EFD9

• Made of ABS plastic with translucent sides and opaque black back

• Dispenses a one-shot volume of skin cleanser or hand sanitizer when activated by placing hand under unit

• Accommodates a sealed 1.2-liter skin cleanser or hand sanitizer cassette that easily snaps into place

• Lights for low battery and low product for easier maintenance

• Choice of key-activated spring lock or push-button operation

• 3 D-Cell Batteries included

• Hardware included for mounting

• One per case

Form # 034128

Suggested mounting height is 48” from the floor or 12” above a counter to the bottom of the dispenser.

�When installed properly and used with the corresponding product, this dispenser meets ADA Standard 28 CFR Part 36, local rules may vary.

7.25”

11.5”

4”

A5077

NOMENCLATURE Dispenser,Paper Towel,SS,Surface Mounted JSN A5080

Weight (lbs) 4 Weight (kg) 2

Height (in) 9 Height (cm) 23

Width (in) 13 Width (cm) 33

Depth (in) 7 Depth (cm) 18

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ

BTU / HR 0

WATTS 0

Description A surface mounted, satin finish stainless steel, single-fold, paper towel dispenser. Dispenser features:

tumbler lock; front hinged at bottom; and refill indicator slot. Minimum capacity 400 single-fold paper towels. For general purpose use throughout the facility.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Technical Data

S

10-13/16" 275mm

7-1/2" 190mm

Lock & Key

Door S

S

S

3-15/16" 100mm

Finish Face of Wall

14-1/16" 355mm

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r to

0" to

0m m

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r

F o r A cc es si b le D es ig n

0m m10-7/16"

265mm

S S

MATERIALS:

Cabinet — 18-8, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish. Towel tray has hemmed opening to dispense paper towels without tearing.

Door — 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Secured to cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom accessories.

Optional: Order Bobrick Part No. 262-130 TowelMate® available as an optional accessory. TowelMate accessory allows for paper towels to dispense one at a time without bulging, sagging or falling through the towel tray opening. TowelMate fits Gamco and most manufacturers' similar models.

OPERATION:

Unit dispenses C-fold and multifold paper towels 3-1/8" to 3-13/16" (79–97mm) deep. Slots in sides of cabinet indicate refill time. Capacity: 400 C-fold or 525 multifold paper towels. To dispense narrower towels 2-1/2" to 3-1/8" (64–79mm) deep, order optional TowelMate accessory Bobrick Part No. 262-130.

INSTALLATION:

Mount unit on wall with four #10 x 1-1/4" (4.8 x 32mm) sheet-metal screws (not furnished) at four of the eight mounting holes indicated by an S (top slots and bottom holes preferable). For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure with sheet-metal screws. For other wall surfaces, provide fiber plugs or expansion shields for use with sheet-metal screws, or provide 1/8" (3mm) toggle bolts or expansion bolts.

SPECIFICATION:

Surface-mounted paper towel dispenser shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Door shall be secured to cabinet with a full-length stainless steel piano-hinge and equipped with a tumbler lock keyed like other Bobrick washroom accessories. Paper towel tray shall have hemmed opening to dispense paper towels without tearing. Unit shall be capable of dispensing 400 C-fold or 525 multifold paper towels measuring 3-1/8" to 3-13/16" (79 to 97mm) deep. Narrower paper towels 2-1/2" to 3-1/8" (65 to 79mm) deep may be efficiently dispensed with the use of an optional TowelMate accessory, Bobrick Part No. 262-130. TowelMate accessory allows for paper towels to dispense one at a time without bulging, sagging or falling through the towel tray opening.

Surface-Mounted Paper Towel Dispenser shall be Model B-262 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

ClassicSeries®

SURFACE-MOUnTED

PAPER TOWEL DISPENSER

B-262 A5080

NOMENCLATURE Dispenser,Paper Towel,Sensor,Hands Free JSN A5082

Weight (lbs) 8 Weight (kg) 4

Height (in) 18 Height (cm) 46

Width (in) 15 Width (cm) 38

Depth (in) 11 Depth (cm) 28

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ 0

BTU / HR 0

WATTS 0

Description A surface mounted, sensor activated, automatic, roll paper towel dispenser. The unit dispenses a paper towel automatically only when hands are place in position below the dispenser for maximum sanitation and hygiene. May include adjustable settings for sheet length, time delay, and sensor range. Unit is battery operated or with optional AC power adapter.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Specification Sheet: 59466A enMotion® 8” Recessed Automated Touchless Roll Paper Towel Dispenser, Stainless

1 If installing directly into a wall, a rough cut-out of 15.5” high x 10.6” wide x 4” deep will be required. Mounting should comply with ADA guidelines.

Compliance is the responsibility of the installer.

2 Screw holes on the inside of the unit are provided to secure the unit to wall studs.

The dispenser door comes mounted on the left side of the housing. If there is not enough clearance for the door on that side of your space the door can be reversed to hinge on the right side.

4”

16.7”

13.6” 8”

10.6”

15.5” 4”

Installation

Operation

Specifications

This automated towel dispenser utilizes an 8” wide towel roll available at GPPRO.com (89415, 89430, 89420, 89410 and 89440). A blue light will illuminate on the front of the dispenser lens when a towel is successfully dispensed. In the event of a jam three lights will flash behind the sensor lens. When batteries are low a red light will illuminate behind the battery icon on the sensor lens. When paper is low a red light will illuminate behind the low paper icon on the sensor lens. Additionally, the dispenser is equipped with settings that allow adjustment of sheet length, dispenser delay, and choosing between auto supply and motion mode. Instructions on how to adjust these settings are included on the inside of the dispenser cover. The dispenser’s cover hinges at the side and cab be swapped to open left or right. For questions regarding this dispenser or for replacement parts, please call: 1-866-HELLOGP (1-866-435-5647). www.gppro.com

COLOR Stainless Steel

FINISH Stainless Steel #4 Brush

DIMENSIONS 13.6”W x 16.7”H x 4/8”D

WEIGHT 6lbs 4oz

ACCESS

MANUFACTURER GP PRO

MODEL/ SKU NUMBER 59466A

POWER Option 1: Four D-cell alkaline batteries (included)

COMPATABLE TRASH

RECEPTACLES

59491, 59451, 59453, 59471

Keyed at cover side (key included). Replacement key: 50504. Key bypass twist-to-open insert available: 50429

Option 2: AC adapter - 120V Plug (59479A) or 24VAC-6V DC (59477A)

© 2018 GP PRO. All rights reserved.D-100362 REV A

A5082

NOMENCLATURE Disposal,Sanitary Napkin,SS,Surface Mounted JSN A5090

Weight (lbs) 4 Weight (kg) 2

Height (in) 12 Height (cm) 30

Width (in) 9 Width (cm) 23

Depth (in) 5 Depth (cm) 13

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ

BTU / HR 0

WATTS 0

Description A surface mounted, satin finish stainless steel, sanitary napkin disposal. Disposal features a flip-up cover, secured to the container by a heavy duty stainless steel piano-hinge. Disposal may be secured to wall or toilet partition. For general purpose use in female toilet stalls or rooms and uni-sex toilet rooms.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Technical Data continued . . .

MATERIALS:

Flanges (2) — 18-8, Type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction.

Radius on corners and return edges complement corners and edges of door. One flange has four mounting screw holes for through-panel mounting. Other flange has four stainless steel weld-nuts to accept mounting screw threads.

Doors (2) — 18-8, Type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction.

Front of doors have same degree of arc as other Bobrick Contura Series washroom accessories. Radius on corners and edges of door match other Contura Series accessories. Self-closing door is secured to flange with a full-length stainless steel piano-hinge at bottom. Each door is equipped with two stainless steel cable door-swing limiters, a finger-pull recess at top for easy opening, and an international graphic symbol identifying sanitary napkin disposal.

Receptacle — Leak-proof molded polyethylene. Removable for servicing. Capacity: 0.7-gal. (2.7-L).

Sight-Barrier — 1/8" (3mm) thick stainless steel. Attached to flange with two stainless steel piano-hinges.

B-4354 ConturaSeries®

PARTITION-MOUNTED

SANITARY NAPKIN DISPOSAL

(FOR TWO TOILET COMPARTMENTS)

Rough Wall Opening 11" (280mm) wide

9-3/8" (240mm) high 1/2" to 1-1/4" (13 to 32mm) partition thickness

11-11/16'' Typ.

295mm

10-13/16'' 275mm

(Flange Outside)

11'' 279mm

17/32'' Typ.

13mm

12-3/4'' 324mm

Flange Return Typ.

Plastic Receptacle

S

1-5/16'' Typ.

33mm

Stainless Steel Door

9'' Typ.

230mm

1'' Typ.

25mm

S

1/8'' Typ.

3mm

Weld Nut Typ.

Finish Face of Panel 1/4'' Typ.

6mm

1/2'' min. to 1-1/4'' max.

13 to 32mm

Partition Thickness

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r

U ni ve rs al

A cc es si bl e

D es ig n m m

A5090

OPERATION:

Serves two toilet compartments. Self-closing doors pull down for access to disposal with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Receptacle is removable from either side of unit for servicing. Cable door-swing limiters prevent damage to washroom accessories and walls. Hanging sight-barrier swings out of the way when waste is deposited in receptacle and when removing receptacle from unit for servicing.

INSTALLATION:

Mount unit in toilet partition 1/2" to 1-1/4" (13 to 32mm) thick, centered through a cutout specially ordered from partition manufacturer or field cut. Dimensions of cutout are to be 11" wide x 9-3/8" high (280 x 240mm). For factory-made cutouts,location and size details must be furnished to partition manufacturer.

Note: Cutouts in Bobrick laminated plastic toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and size of cutouts are specified and order for both partitions and accessories are received together.

For installation with machine screws furnished by manufacturer, place the door assembly with four mounting holes in the flange firmly in one side of the partition cutout. Use the flange as a template to mark mounting hole locations, indicated by an S, then drill (4) 5/16" (7.9mm) diameter holes through the partition. Place the door assembly with four weld-nuts on the rear of the flange on the opposite side of partition, making sure the weld-nuts go into the mounting holes in partition. Secure the door assemblies together, back-to-back, using screws furnished, tightening screws until flanges are flush with and tight against partition surface. For installation in 1/2" (13mm) thick partitions, use short screws furnished. For installation in 1" (25mm) thick partitions, use long screws furnished. For other panel thicknesses, provide screws as needed. Screw length to be the same as the panel thickness. Attach loose ends of cable door-swing limiters to opposite weld-studs in second door using two hex lock-nuts furnished by manufacturer. Ends of door-swing limiters must rotate freely around weld-studs. Attach door-return springs to spring-retainer brackets at inside bottom of doors, both left and right sides. Place end of spring wire through hole in spring-retainer bracket with end of spring wire facing toward the outside of the unit. Attach the other end of the spring to the spring-retainer bracket of the door on the opposite side of the panel in the same manner. Repeat this procedure for the second spring on the other side of the unit.

SPECIFICATION:

Partition-mounted sanitary napkin disposal shall be Type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Unit shall mount in partition and serve two toilet compartments. Front of sanitary napkin disposal doors shall have same degree of arc and match other Bobrick ConturaSeries accessories in the washroom. Radius on corners and edges of flanges and doors shall complement other Bobrick ConturaSeries washroom accessories. Flanges shall be drawn, one-piece, seamless construction. Each self-closing door shall be drawn, one-piece, seamless construction; secured to flange with a full-length stainless steel piano-hinge; and equipped with two stainless steel cable door-swing limiters, a finger-pull recess at top for easy opening, and an international graphic symbol identifying sanitary napkin disposal. Doors shall pull down with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Unit shall be furnished with a removable, leak-proof, molded polyethylene receptacle that is serviced from either side of unit. Receptacle shall have a capacity of 0.7-gal. (2.7-L). Unit is furnished with a hanging sight-barrier, secured to flange with two stainless steel piano-hinges, which swings out of the way when waste is deposited in receptacle and when removing receptacle from unit for servicing.

Partition-Mounted Sanitary Napkin Disposal shall be Model B-4354 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

A5090

NOMENCLATURE Waste Disposal Unit,Sharps JSN A5108

Weight (lbs) 2 Weight (kg) 1

Height (in) 27 Height (cm) 69

Width (in) 20 Width (cm) 51

Depth (in) 15 Depth (cm) 38

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ

BTU / HR 0

WATTS 0

Description A container for collecting and transporting syringes and other sharps for decontamination and disposal. Available in 2 gallon and 8 gallon with locking rotor. Complies with OSHA regulations for handling sharps.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

B D

D is p o sa l S o lu ti o n s

305616

305610

Key product features include:

• �Temporary and final closure features

• �Visual, audible, tactile (VAT) perimeter locks to ensure that the lid is securely attached to the base and to provide security against tampering

• �Double-wall handles for safe transportation

• �Clear tops to ensure visibility of collector fill level

• �Easy accessibility for disposal of large and bulky waste

• �Dual-opening hinge top designed so that the small or the large side can remain open and the other locked based on the size of access opening desired

BD Large and Extra Large Collectors are fully compatible with trolleys to provide stability and mobility (see page 16 for details).

Large and Extra-Large Sharps Collectors

DUAL OPENSLIDE TOPHANDS FREE

ABSORBENT

SECURITY HANDS FREE

HIGH TEMP

INCINERATOR

LOW TEMP

INCINERATOR

DUAL OPENSLIDE TOPHANDS FREE

ABSORBENT

SECURITY HANDS FREE

HIGH TEMP

INCINERATOR

LOW TEMP

INCINERATOR

* Meets or exceeds US DOT packaging requirements 49 CFR 173.24, 49 CFR 173.24a, and 49 CFR 173.134.

See Trolleys on page 15.

Large and Extra-Large Sharps

Reference # Product Size Product Dimensions ( H x W x D inches )

Qty Case

Compatible with

305615 9 gal Hinge Top 18.5 x 17.75 x 11.75 8 305090

305601* 9 gal Hinge Top with Gasket 18.5 x 17.75 x 11.75 8

305616 9 gal Slide Top 18.5 x 17.75 x 11.75 8 305090, 305091

305602* 9 gal Slide Top with Gasket 18.5 x 17.75 x 11.75 8

305610 17 gal Hinge Top 23.5 x 20 x 14.75 5 305092

305665* 17 gal Hinge Top with Gasket 23.5 x 20 x 14.75 5

305609 19 gal Slide Top 26.25 x 20 x 14.75 5 305092, 305093

305666* 19 gal Slide Top with Gasket 26.25 x 20 x 14.75 5

A5108 cphillips Rectangle cphillips Line

B D

D isp o sal So lu tio n s

305090

305092

305091

305093

Collectors not included.

Key product features include:

• �A design that helps minimize the risk of collectors tipping over

• �Wheels that enable the collector to be conveniently placed where it will be most used

• �Locking wheels, ensuring the product is mobile only when you want it to be

• �The ability to open and close the collector for hands-free disposal (foot-operated trolleys only)

• �A two-year warranty providing product replacement in case of manufacturer defects

Trolleys Our full line of BD Recykleen™ Trolleys are available in basic and foot-operated versions for use with large and extra-large collectors. Trolleys provide stability and mobility for large and extra-large collectors.

DUAL OPENSLIDE TOPHANDS FREE

ABSORBENT

SECURITY HANDS FREE

HIGH TEMP

INCINERATOR

LOW TEMP

INCINERATOR

25%

Product made from a minimum of 25% recycled materials

BD Recykleen™ Trolleys

Reference # Product Size Product Dimensions ( H x W x D inches )

Qty Case Compatible with

305090 9 gal BD Recykleen™ Basic Trolley 23.5 x 16.3 x 28.6 1 All 9 gal

305091 9 gal BD Recykleen™ Foot-operated Trolley 23.5 x 16.3 x 28.6 1 All 9 gal Slide Top

305092 17 and 19 gal BD Recykleen™ Basic Trolley 24.1 x 18 x 27.5 1 All 17 and 19 gal

305093 19 gal BD Recykleen™ Foot-operated Trolley 24.3 x 17.7 x 35.2 1 All 19 gal Slide Top

A5108 cphillips Rectangle

NOMENCLATURE Grab Bar,ABA Compliant,SS,2-Wall,W/C Accessible JSN A5109

Weight (lbs) 7 Weight (kg) 3

Height (in) 3 Height (cm) 8

Width (in) 57 Width (cm) 145

Depth (in) 3 Depth (cm) 8

Utility 1: Plumbing . |

Utility 2: Electrical . |

Utility 3: Med Gas . |

Utility 4: Misc Gas . |

Utility 5: Non-Med Gas . |

Utility 6: Misc . |

PHASE 0

AMPS 0

VOLTS 0

HERTZ

BTU / HR

WATTS 0

Description A 1-1/4" diameter, satin finish stainless steel, peened gripping surface, 2 wall toilet stall/ room, grab bar with concealed mounting flanges. Snap over flanges are provided to conceal mounting screws. A selection of mounting kits and concealed anchor devices are available from the manufacturers for different types of installations. Grab bar shall comply with barrier-free accessibility guidelines for structural strength. For typical water closet applications in toilet stalls and rooms where ADA (American's With Disabilities Act) requirements must be met.

Weights and Measures (Typical Only)

Utilities NOTE: Values shown are based on standard typicals used for programming purposes. The contractor remains responsible to develop

Grab Bar Series

© 2021 Bradley P.O.