567_Cooper_St._Asbestos_Containing_Materials_and_Hazardous_Materials_Report_092925.pdf

P.O. Box 13216

Lansing, MI 48901

Phone: 888.449.4566

Fax: 888.448.8739 www.redcedarconsulting.net

September 29, 2025

Mr. Brian Taylor

City of Jackson

Community Development Department

Jackson, MI 49202

RE: Asbestos Containing Material and Hazardous Materials Inspection

567 Cooper St. Jackson, MI 49201

Parcel ID: 7-066900000

Dear Mr. Taylor:

Red Cedar Consulting has completed an asbestos-containing material (ACM) and hazardous materials inspection at 567 Cooper St. Jackson, Michigan (Subject Property). This inspection was completed at the request of the City of Jackson to comply with the United States Environmental Protection Agency

(USEPA) requirements for demolition and renovation set forth under the National Emissions Standards for Hazardous Air Pollutants (NESHAP, 40 CFR Part 61). This inspection was also completed to comply with the Occupational Safety and Health Administration (OSHA) Asbestos Standards for Construction

(29 CFR 1926.1101) which limits employee exposure to asbestos.

SUBJECT PROPERTY

The Subject Property is comprised of a .10-acre residential parcel which contains a 396 sq. ft. detached garage and approximate 1,320 square foot residential building (the Building) constructed in 1890. The

Building was constructed on a concrete basement with two aboveground floors. The exterior walls of the

Building were finished with cedar and vinyl siding over wood lap while the roof was sealed with asphalt shingles. The Building can be further divided into a front entry, living room, dining room, kitchen, bathroom, bedroom and rear entry on the first floor while the second floor contains two bedrooms and a bathroom.

VISUAL INSPECTION AND SAMPLING

Asbestos Containing Materials Inspection

Jeff Cain of Red Cedar Consulting (Red Cedar), accredited State Of Michigan/EPA Asbestos Building

Inspector (Accreditation Number A14057) who completed training per the Michigan Asbestos Workers

Accreditation Act 440, completed an inspection of the Subject Property on September 25, 2025, for suspected asbestos containing building materials.

Project No.: 12-1027

Parcel ID: 567 Cooper St.

This inspection, and subsequent sample collection was completed in accordance with the USEPA

Asbestos Hazard Emergency Response Act (AHERA) (40 CFR Part 763) assessment and sampling protocol.

During the completion of the inspection, each area of the Subject Property was visually inspected for asbestos containing building materials (ACBM). Following the completion of the visual inspection, Red

Cedar staff identified each suspect area of friable and non-friable ACBM and sorted them into one of three homogenous categories for sampling purposes. AHERA defines friable as a material that when dry, may be crumbled, pulverized, or reduced to powder by hand pressure. A homogenous area is defined by

OSHA as an area of surfacing, thermal system insulation (TSI) or miscellaneous material that is uniform in color and texture. Surfacing materials are most commonly found in sprayed-on, troweled-on or otherwise applied to surfaces, such as acoustical plaster on ceilings and fireproofing materials on structural members. TSI refers to materials applied to pipes, fittings, boilers, ductwork, or other components to prevent heat loss or gain, or condensation. Any material that does not fall under the surfacing or TSI category, such as floor tile, drywall, and acoustical ceiling tile are placed into the miscellaneous materials category.

Following the completion of the visual inspection, Red Cedar staff identified the following materials as suspect ACBM:

• Asphalt Shingle

• Brick and Mortar

• Window Trim Caulk

• Glass Block Grout

• Tar Paper

• 12”x12” Floor Tile

• Ceramic Tile and Grout

• Plaster

Red Cedar staff collected twenty-nine samples of suspect ACBM separated into fourteen distinct homogenous groups for laboratory analysis. Samples were collected and submitted to APEX Research

Inc. Laboratories (APEX) (Accreditation Number 102118-0) for laboratory analysis. Analysis was completed utilizing polarized light microscopy (PLM) which is the Environmental Protection Agency

(EPA) approved method for analysis of bulk materials for asbestos. PLM analysis completed pursuant to method (EPA 600/M4-82-020) identifies asbestos fiber bundles by the visual properties displayed when the sample is treated with various dispersion staining liquids. The laboratory report completed following the sample analysis indicates if asbestos is present, and at what percentage along with a description and percentage of other fibrous and non-fibrous materials and sample color. Chain-of-custody documentation was followed from sample collection through shipping and receiving of the samples at the designated laboratory. The documentation assures that samples will meet the quality assurance/quality control measures defined by AHERA. The laboratory analytical report prepared by APEX for the twenty-nine samples is included as Attachment A.

Hazardous Materials Inspection

On September 25, 2025, the Subject Property was also inspected for the presence of hazardous materials which include but are not limited to polychlorinated biphenyls (PCBs) and potential mercury containing equipment and any items or containers that may contain or be classified as a hazardous or regulated material. Each material, if identified, was documented along with the approximate location. Any materials identified as hazardous are included in Table 1.

INSPECTION RESULTS AND RECOMMENDATIONS

During the completion of the asbestos inspection, twenty-nine samples of suspect ACM were collected and are documented in Table 2 along with the Red Cedar sample number, description, friability, material type, ACM classification, sample location, material quantity and laboratory analytical results. A Site

Diagram was prepared which provides the general building layout and sample locations and is included as

Attachment B.

ACM, as defined by the USEPA NESHAP is “any material containing more than 1 percent asbestos as determined using the method specified in appendix E, subpart E, 40 CFR part 763 Section 1, Polarized

Light Microscopy”.

Friable ACM is defined by NESHAP as any material containing more than 1 percent asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. Friable ACM is a concern due to the ease of unintentionally disturbing the ACM which may result in “visible emissions” which is known as a Fiber Release Episode.

Non-friable asbestos-containing material is defined as “material containing more than 1 percent asbestos that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure. Non-friable

ACMs are separated into Category I and Category II ACM. Category I ACM is any asbestos containing packing’s, gaskets, resilient floor coverings (vinyl floor tile and linoleum are examples of these) and asphalt roofing products. Category II ACM is stated by NESHAP as any material excluding Category I non-friable ACM such as drywall, plaster or fiberboard insulation.

Presumed Asbestos Containing Material

Presumed Asbestos Containing Materials (PACM) are suspect surfacing, TSI and miscellaneous materials found in buildings constructed prior to 1980 which are classified as and due to the age of the structure, are assumed to be ACM and do not require sample collection and analysis. OSHA dictates that PACM may be “rebutted” following a complete inspection pursuant to AHERA protocol.

The HVAC Duct Wrap located in the Building was classified as PACM due to the age of the structure and samples were not collected.

Table 3 lists the location, material description, friability, condition, material type (surfacing, thermal or miscellaneous) and approximate quantity of all PACM documented at the Subject Property.

Table 4 provides a summary of all ACM documented at the Subject Property which includes the material location, description, and approximate quantity.

Friable ACM’s

Duct Wrap identified in the building in conjunction with the forced air heating system is classified as friable ACM. The visual assessment to quantify the extent of this material identified HVAC Duct Wrap at the following locations within the basement, first and second floors:

• Basement (5 Register Boots 5 sq. ft. each, 25 sq. ft.)

• Basement (6 in. Misc. HVAC Wrap, 20 lin. ft.)

Category I ACM

No Category I ACM was identified during the completion of this inspection.

Category II ACM

Window trim caulk samples collected from windows in the Building were found to contain up to 5% asbestos following analysis. The assessment to quantify the extent of this material identified nine windows at the following locations that would fall into the same homogenous group. The locations of the windows are listed below:

• 1st Floor (1 window 30” wide x 34” tall)

• 1st Floor (2 windows 36” wide x 36” tall)

• 1st Floor (2 windows 30” wide x 52” tall)

• 1st Floor (1 window 52” wide x 60” tall)

• 2nd Floor (1window 44” wide x 62” tall)

• 2nd Floor (1 window 24” wide x 48” tall)

• 2nd Floor (1 window 44” wide x 80” tall)

RECOMMENDATIONS

Asbestos Containing Materials

HVAC material identified in the Building system and listed below is classified as friable ACM and should be removed prior to any renovation/demolition activities.

• Basement (5 Register Boots 5 sq. ft. each, 25 sq. ft.)

• Basement (6 in. Misc. HVAC Wrap, 20 lin. ft.)

Non-Friable asbestos containing window trim caulk was identified on nine windows throughout the

Building. The locations of these windows that should be abated prior to demolition/renovation activities are listed below:

• 1st Floor (1 window 30” wide x 34” tall)

• 1st Floor (2 windows 36” wide x 36” tall)

• 1st Floor (2 windows 30” wide x 52” tall)

• 1st Floor (1 window 52” wide x 60” tall)

• 2nd Floor (1window 44” wide x 62” tall)

• 2nd Floor (1 window 24” wide x 48” tall)

• 2nd Floor (1 window 44” wide x 80” tall)

Please note: Other different sized windows are located throughout the Building but these windows were assessed and found to be constructed either without window glazing or were sampled and found to not contain asbestos and therefore are not required to be removed.

Please note: The location of samples obtained during this inspection were in a random fashion and areas that were not identified during this inspection may be damaged or have become damaged since the inspection was completed. If Category I or Category II friable materials are discovered prior to or during the demolition/renovation process, these materials must be abated prior to commencement of any demolition/renovation activities at the Subject Property.

Hazardous Materials

Hazardous Materials identified at the Subject Property and documented in Table 1 which require proper removal and disposal consist of the following items:

• 20 lb. Propane Tank (2)

REGULATORY REQUIREMENTS

A Notification of intent to Renovate/Demolish form must be filed with the Michigan Department of

Environmental Quality- Air Quality Division at least 10 working days prior to any renovation or demolition activities at a site.

The Notification of Intent to Renovate/Demolish form must also be completed and submitted to the

MIOSHA-Asbestos Program whenever demolition, encapsulation and/or renovation activities at a site involving greater than ten lineal feet and/or fifteen square feet of ACM will be completed.

Regulated asbestos containing materials per NESHAP (40 CFR Part 61) which falls into any of the following categories are ACM’s that must be removed prior to any renovation/demolition activities at the

Subject Property.

• Friable asbestos material.

• Category I non-friable ACM that has become friable.

• Category I non-friable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading.

• Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of renovation or demolition operations.

Asbestos abatement should only be performed by a certified asbestos abatement contractor licensed to complete abatement work. The contractor must also follow the standards and requirements set forth per the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR

Part 61).

Additional information regarding the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR Part 61) can be obtained by contacting the associated agency below.

NESHAP Asbestos Program MIOSHA-CSHD-Asbestos Program

Department of Environmental Quality State of Michigan

Phone: 517-284-6777 Phone: 517-284-7680

Email: asbestos@michigan.gov

DISCLAIMER

Red Cedar Consulting performed destructive testing methods in an attempt to access and inspect all areas of the Building. Unfortunately, due to the age of construction along with multiple additions/renovations that may have been completed on the Building, additional inspections may be required if suspect ACM material not documented within this report is encountered during renovation/demolition activities.

This report was prepared at the request and for exclusive use by the City of Jackson and may not be reproduced or sold without written permission from Red Cedar Consulting.

We appreciate the opportunity to provide the requested services. Please contact us at (888) 449-4566 with any questions or concerns.

Sincerely, Red Cedar Consulting

Aaron Paquet

Michigan/EPA Certified Asbestos Building Inspector

(A30955)

©2025 Red Cedar Consulting, LLC.

Attachment A

APEX Research Laboratory Analytical Results

Certificate of Laboratory Analysis Test Method, Polarized Light Microscopy (PLM)

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 01 Asbestos Present: NO Fiberglass - 30%

Cust. #: CS-HM-01A No Asbestos Observed Other - 70% Material: Roofing M/L Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 119928 - 01a Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-01A No Asbestos Observed Other - 70% Material: Black Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

Lab ID #: 119928 - 01b Asbestos Present: NO Cellulose - 40% Cust. #: CS-HM-01A No Asbestos Observed Other - 60% Material: Brown Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 3 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Project: 567 Cooper St.

Project #: Jackson, MI

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Liability limited to cost of analysis.

NVLAP Lab Code 102118-0

APEX Research Inc., 7717 Kensington Ct., Brighton, MI 48116

(734) 449-9990, Fax (734) 449-9991 Page 1 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 01c Asbestos Present: NO Cellulose - 40%

Cust. #: CS-HM-01A No Asbestos Observed Other - 60% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 119928 - 02 Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-01B No Asbestos Observed Other - 70% Material: Roofing M/L Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 119928 - 02a Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-01B No Asbestos Observed Other - 70% Material: Black Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 2 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 02b Asbestos Present: NO Cellulose - 40%

Cust. #: CS-HM-01B No Asbestos Observed Other - 60% Material: Brown Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 3 of 4

Lab ID #: 119928 - 02c Asbestos Present: NO Cellulose - 60% Cust. #: CS-HM-01B No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 119928 - 03 Asbestos Present: NO Other - 100% Cust. #: CS-HM-02A No Asbestos Observed Material: Brick Location:

Appearance: red,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 3 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 03a Asbestos Present: NO Other - 100%

Cust. #: CS-HM-02A No Asbestos Observed Material: Mortar Location:

Appearance: grey,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119928 - 04 Asbestos Present: NO Other - 100% Cust. #: CS-HM-02B No Asbestos Observed Material: Brick Location:

Appearance: red,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 04a Asbestos Present: NO Other - 100% Cust. #: CS-HM-02B No Asbestos Observed Material: Mortar Location:

Appearance: grey,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 4 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 05 Asbestos Present: NO Other - 100%

Cust. #: CS-HM-03A No Asbestos Observed Material: 1st Floor Vinyl Window Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 06 Asbestos Present: NO Other - 100% Cust. #: CS-HM-03B No Asbestos Observed Material: 1st Floor Vinyl Window Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 07 Asbestos Present: NO Other - 100% Cust. #: CS-HM-04A No Asbestos Observed Material: 2nd Floor Vinyl Window Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 5 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 08 Asbestos Present: NO Other - 100%

Cust. #: CS-HM-04B No Asbestos Observed Material: 2nd Floor Vinyl Window Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 09 Asbestos Present: YES Other - 95% Cust. #: CS-HM-05A Chrysotile - 5% Material: 1st Floor Wood Trim Caulk Window Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 10 Asbestos Present:

Cust. #: CS-HM-05B Material: 1st Floor Wood Trim Caulk Window Location: NOT ANALYZED Appearance:

Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 6 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 11 Asbestos Present: YES Other - 95%

Cust. #: CS-HM-06A Chrysotile - 5% Material: 2nd Floor Wood Trim Caulk Window Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 12 Asbestos Present:

Cust. #: CS-HM-06B Material: 2nd Floor Wood Trim Caulk Window Location: NOT ANALYZED Appearance:

Layer: 1 of 1

Lab ID #: 119928 - 13 Asbestos Present: NO Other - 100% Cust. #: CS-HM-07A No Asbestos Observed Material: Basement Glass Block Grout Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 7 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 14 Asbestos Present: NO Other - 100%

Cust. #: CS-HM-07B No Asbestos Observed Material: Basement Glass Block Grout Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 15 Asbestos Present: NO Cellulose - 60% Cust. #: CS-HM-08A No Asbestos Observed Other - 40% Material: Tar Paper Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119928 - 16 Asbestos Present: NO Cellulose - 60% Cust. #: CS-HM-08B No Asbestos Observed Other - 40% Material: Tar Paper Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 8 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 17 Asbestos Present: NO Fiberglass - 30%

Cust. #: CS-HM-09A No Asbestos Observed Other - 70% Material: Roofing M/L Garage Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 119928 - 17a Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-09A No Asbestos Observed Other - 70% Material: Black Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

Lab ID #: 119928 - 17b Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-09A No Asbestos Observed Other - 70% Material: Green Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 3 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 9 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 17c Asbestos Present: NO Cellulose - 60%

Cust. #: CS-HM-09A No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 119928 - 18 Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-09B No Asbestos Observed Other - 70% Material: Roofing M/L Garage Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 119928 - 18a Asbestos Present: NO Fiberglass - 30% Cust. #: CS-HM-09B No Asbestos Observed Other - 70% Material: Black Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 10 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 18b Asbestos Present: NO Fiberglass - 30%

Cust. #: CS-HM-09B No Asbestos Observed Other - 70% Material: Green Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 3 of 4

Lab ID #: 119928 - 18c Asbestos Present: NO Cellulose - 60% Cust. #: CS-HM-09B No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 119928 - 19 Asbestos Present: NO Other - 100% Cust. #: CS-HM-10A No Asbestos Observed Material: 12"x12" Floor Tile Location:

Appearance: brown,nonfibrous,homogenous Layer: 1 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 11 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 19a Asbestos Present: NO Other - 100%

Cust. #: CS-HM-10A No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 4

Lab ID #: 119928 - 19b Asbestos Present: NO Other - 100% Cust. #: CS-HM-10A No Asbestos Observed Material: Ceramic Tile Location:

Appearance: white,nonfibrous,homogenous Layer: 3 of 4

Lab ID #: 119928 - 19c Asbestos Present: NO Other - 100% Cust. #: CS-HM-10A No Asbestos Observed Material: Grout Location:

Appearance: grey,nonfibrous,homogenous Layer: 4 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 12 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 20 Asbestos Present: NO Other - 100%

Cust. #: CS-HM-10B No Asbestos Observed Material: 12"x12" Floor Tile Location:

Appearance: brown,nonfibrous,homogenous Layer: 1 of 4

Lab ID #: 119928 - 20a Asbestos Present: NO Other - 100% Cust. #: CS-HM-10B No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 4

Lab ID #: 119928 - 20b Asbestos Present: NO Other - 100% Cust. #: CS-HM-10B No Asbestos Observed Material: Ceramic Tile Location:

Appearance: white,nonfibrous,homogenous Layer: 3 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 13 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 20c Asbestos Present: NO Other - 100%

Cust. #: CS-HM-10B No Asbestos Observed Material: Grout Location:

Appearance: grey,nonfibrous,homogenous Layer: 4 of 4

Lab ID #: 119928 - 21 Asbestos Present: NO Other - 100% Cust. #: CS-HM-11A No Asbestos Observed Material: 12"x12" Floor Tile M/L Location:

Appearance: beige,nonfibrous,homogenous Layer: 1 of 6

Lab ID #: 119928 - 21a Asbestos Present: NO Other - 100% Cust. #: CS-HM-11A No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 6

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 14 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 21b Asbestos Present: NO Other - 100%

Cust. #: CS-HM-11A No Asbestos Observed Material: White Floor Tile Location:

Appearance: white,nonfibrous,homogenous Layer: 3 of 6

Lab ID #: 119928 - 21c Asbestos Present: NO Other - 100% Cust. #: CS-HM-11A No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 4 of 6

Lab ID #: 119928 - 21d Asbestos Present: NO Other - 100% Cust. #: CS-HM-11A No Asbestos Observed Material: Brown Floor Tile Location:

Appearance: brown,nonfibrous,homogenous Layer: 5 of 6

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 15 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 21e Asbestos Present: NO Other - 100%

Cust. #: CS-HM-11A No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 6 of 6

Lab ID #: 119928 - 22 Asbestos Present: NO Other - 100% Cust. #: CS-HM-11B No Asbestos Observed Material: 12"x12" Floor Tile M/L Location:

Appearance: beige,nonfibrous,homogenous Layer: 1 of 6

Lab ID #: 119928 - 22a Asbestos Present: NO Other - 100% Cust. #: CS-HM-11B No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 6

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 16 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 22b Asbestos Present: NO Other - 100%

Cust. #: CS-HM-11B No Asbestos Observed Material: White Floor Tile Location:

Appearance: white,nonfibrous,homogenous Layer: 3 of 6

Lab ID #: 119928 - 22c Asbestos Present: NO Other - 100% Cust. #: CS-HM-11B No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 4 of 6

Lab ID #: 119928 - 22d Asbestos Present: NO Other - 100% Cust. #: CS-HM-11B No Asbestos Observed Material: Brown Floor Tile Location:

Appearance: brown,nonfibrous,homogenous Layer: 5 of 6

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 17 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 22e Asbestos Present: NO Other - 100%

Cust. #: CS-HM-11B No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 6 of 6

Lab ID #: 119928 - 23 Asbestos Present: NO Other - 100% Cust. #: CS-HM-12A No Asbestos Observed Material: Ceramic Tile Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 23a Asbestos Present: NO Other - 100% Cust. #: CS-HM-12A No Asbestos Observed Material: Grout Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 18 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 24 Asbestos Present: NO Other - 100%

Cust. #: CS-HM-12B No Asbestos Observed Material: Ceramic Tile Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 24a Asbestos Present: NO Other - 100% Cust. #: CS-HM-12B No Asbestos Observed Material: Grout Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119928 - 25 Asbestos Present: NO Other - 100% Cust. #: CS-HM-13A No Asbestos Observed Material: 12"x12" Vinyl Floor Tile Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 19 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 25a Asbestos Present: NO Other - 100%

Cust. #: CS-HM-13A No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119928 - 26 Asbestos Present: NO Other - 100% Cust. #: CS-HM-13B No Asbestos Observed Material: 12"x12" Vinyl Floor Tile Location:

Appearance: grey,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 26a Asbestos Present: NO Other - 100% Cust. #: CS-HM-13B No Asbestos Observed Material: Glue Location:

Appearance: clear,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 20 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 27 Asbestos Present: NO Other - 100%

Cust. #: CS-HS-01A No Asbestos Observed Material: Plaster Finish Coat on Lathe Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 27a Asbestos Present: NO Cellulose - 2% Cust. #: CS-HS-01A No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119928 - 28 Asbestos Present: NO Other - 100% Cust. #: CS-HS-01B No Asbestos Observed Material: Plaster Finish Coat on Lathe Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 21 of 22

Report To: ARI Report # 25-119928 Mr. Aaron Paquet Date Collected: 09/25/25 Red Cedar Consulting Date Received: 09/25/25 P.O. Box 13216 Date Analyzed: 09/29/25 Lansing, MI 48901 Date Reported: 09/29/25

Project: 567 Cooper St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119928 - 28a Asbestos Present: NO Cellulose - 1%

Cust. #: CS-HS-01B No Asbestos Observed Other - 99% Material: Plaster Base Coat Location:

Appearance: grey,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119928 - 29 Asbestos Present: NO Other - 100% Cust. #: CS-HS-01C No Asbestos Observed Material: Plaster Finish Coat on Lathe Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119928 - 29a Asbestos Present: NO Cellulose - 2% Cust. #: CS-HS-01C No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 22 of 22

Attachment B Figure 1 Site Diagram

Figure 1a Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations 567 Cooper St.

-Not To Scale- Jackson, MI

Figure 1b Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations

Figure 1c Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations

Tables

Table 1 - Summary of Hazardous Materials, 567 Cooper St. Jackson, Michigan

Hazardous Materials Description and Location

Location Material Description Quantity

Garage 20 lb. Propane Tank 1

Basement 20 lb. Propane Tank 1

Table 2 - Summary of Sample Descriptions and Asbestos Laboratory Results, 567 Cooper St. Jackson, Michigan

Sample

Number Sample Description Friable

Material

Type

Material

Classification

% Asbestos

Laboratory

Result

Sample Location Approx. Material

Quantity

CS-HM-01A Roofing Multilayer No M Category I ND/ND/ND/ND Building Exterior NA

CS-HM-01B Roofing Multilayer No M Category I ND/ND/ND/ND Building Exterior NA

CS-HM-02A Brick and Mortar No M Category I ND/ND Building Exterior NA

CS-HM-02B Brick and Mortar No M Category I ND/ND Building Exterior NA

CS-HM-03A 1st Fl.