36C78618Q0292-008.pdf

07 46 33-1

SECTION 07 46 33

VINYL SIDING

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Vinyl siding.

B. Vinyl trim and accessories.

1.2 SUBMITTALS

A. Samples: Siding design, size, and color for approval.

B. Product Data: Manufacturer's catalog data, standard details and installation instructions.

C. Certificate: Manufacturer's certification that siding as supplied meets or exceeds the conditions specified herein.

1.3 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

B. Pack siding two squares per carton and clearly mark each carton with manufacturer's name, siding style, color, identifying lot number, and VSI Certification Stamp.

C. Store vinyl siding and accessories in clean, dry area, out of direct sunlight. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

D. Handle material to prevent damage. Do not allow cartons to crease.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Alside / Siding, which is located at: P. O. Box 2010 ;

Akron, OH 44309; Toll Free Tel: 800-922-6009; Tel: 330-922-5350; Fax: 330-922- 5387; Email: Dhouston@alside.com; Web: www.alside.com

B. Substitutions: Certain Teed or approved equal

2.2 MATERIALS

A. Vinyl Siding - General Requirements: Produced from polyvinyl chloride (PVC) compounds meeting ASTM D 3679 requirements for compound class number 2.

1. Vinyl Siding Institute Certified.

2. Average Impact Strength: 3.86 ft. lbs./in. (26.61 kPa) of notch at 73.4 degrees F (23 degrees C), per ASTM D 256.

3. Average Impact Strength: 2.4 ft. lbs./in. (16.55 kPa) of notch at 32 degrees F

(0 degrees C), per ASTM D 256.

mailto:Dhouston@alside.com http://www.alside.com/

07 46 33-2

4. Tensile Strength: 6,700 psi (46,195 kPa), per ASTM D 638.

5. Modulus of Elasticity: 410,000 psi (2,826,850 kPa), per ASTM D 638.

6. Deflection Temperature: 170 degrees F (77 degrees C), per ASTM D 648.

7. Fire Properties:

a. Average Time of Burning: Less than 5 seconds, when tested in accordance with ASTM D 635.

b. Average Extent of Burning: Less than 5 mm, when tested in accordance with ASTM D 635.

c. Flame Spread Index: 20 (Class A), when tested in accordance with

ASTM E 84.

d. Smoke Developed Index: Less than 450, when tested in accordance with ASTM E 84.

e. Ignition Temperature: When tested in accordance with ASTM D 1929, no self-ignition and no flaming; no smoldering at less than 680 degrees F (360 degrees C).

8. Typical Vinyl Siding Properties:

a. Camber: Alside sidings meet all requirements for camber per ASTM D

3679.

b. Heat Shrinkage: Alside sidings meet all requirements for heat shrinkage per ASTM D 3679.

c. Impact Resistance: 60 in-lbf, per ASTM D 4226, Procedure A, H.25.

d. Weatherability: No surface or structural defects such as peeling, cracking, or chipping when tested per ASTM D 3679.

e. Coefficient of Linear Expansion: 3.05 by 10-5 in/in F, per ASTM D 696.

f. Gloss: Alside sidings meet all requirements.

g. Surface Distortion: No distortion at 120 degrees F (40.5 degrees C), per ASTM D 3679.

9. Interlock: Post-form style lock with positive interlock; both ends of panels factory cut and notched for overlap.

10. Nail Slots: Elongated 1-inch (25 mm) slots spaced approximately 1/4 inch (6

mm) apart in nailing hem to allow for expansion and contraction.

11. Weep Holes: Small holes under the bottom butt of siding panels to prevent vapor build-up and allow accumulated moisture to escape.

12. Fasteners: Aluminum nails, alloy 5056 or 6110, having minimum tensile strength 63,000 pounds per square inch.

13. Vinyl Siding Critical Elements:

a. Thickness: 0.046 inch (Acrylic Capped Vinyl) that contains titanium dioxide.

b. Color throughout the panel with high-quality pigments.

c. Double-hem nailing area.

d. Extra-long panels to create smooth seamless look.

e. Color and profile to match Committal Shelter B.

2.3 ACCESSORIES

A. Standard Accessories:

1. Consistent with shape, size, and properties shown on the drawings and as required for complete installation.

2. Produced from the same compound materials and with comparable properties as the siding.

3. Color: Matching or color coordinated with siding.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared. Verify

07 46 33-3 dimensions and acceptability of substrate

B. Beginning installation indicates Installer's acceptance of substrate as suitable to accept siding.

3.2 PREPARATION

A. Repair substrate flaws or defects before applying siding.

B. Where necessary, fur surfaces to an even plane and free from obstructions before application.

C. Clean surfaces thoroughly prior to installation.

D. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install siding in accordance with the latest edition of "Vinyl Siding Installation Manual," published by the Vinyl Siding Institute (VSI) and in accordance with manufacturer's instructions.

B. Install vinyl siding and accessories in accordance with best practice, with all joint members plumb and true.

3.4 FIELD QUALITY CONTROL

A. After installation of siding, check entire surface for obvious flaws or defects.

B. Replace and repair any problem areas, paying close attention to the substrate for causes of the problem.

3.5 CLEANING

A. After application of siding, clean as necessary to remove all fingerprints and soiled areas.

B. Upon completion of siding application, clean entire area, removing all scrap, packaging, and unused materials related to this work.

END OF SECTION