36C26118B0301-A0003006.pdf

CONSTRUCT PSYCHOSOCIAL REHABILITATION AND RECOVERY CENTER 612-503

MARTINEZ, CA FINAL – REISSUE FOR BID

ADVANCE DESIGN CONSULTANTS INC.

04/27/2018 08 12 16 - 1

SECTION 08 12 16

ALUMINUM DOOR AND GLAZING FRAMES

PART 1 – GENERAL

1.1 SUMMARY

A. Section includes aluminum frames for interior doors and windows.

B. Related Sections:

1. Section 08 14 16 – Flush Wood Doors.

2. Section 08 71 00 – Door Hardware.

3. Section 08 80 00 – Glazing.

4. Section 09 21 16 – Gypsum Board Assemblies: Rough opening framing in compliance with frame manufacturer’s recommendations.

1.2 REFERENCES

A. Aluminum Association (AA)

1. AA DAF-45 – Designation System for Aluminum Finishes

B. American Architectural Manufacturers Association (AAMA)

1. AAMA 611 – Voluntary Specification for Anodized Architectural Aluminum.

C. ASTM International

1. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

D. National Fire Protection Association (NFPA):

1. NFPA 80 - Standard for Fire Doors and Fire Windows.

1.3 SUBMITTALS

A. Division 1 - Submittal Procedures: Submittal procedures.

B. Product Data: Include typical details, material descriptions, hardware reinforcements, profiles, anchors, fire-resistance rating, and finishes.

C. Manufacturer's Installation Instructions: Include rough opening framing recommendations.

D. Shop Drawings: Indicate frame elevations, reinforcement, anchorage and spacing, location of cut-outs for hardware, and finish.

ADVANCE DESIGN CONSULTANTS INC.

04/27/2018 08 12 16 - 2

E. Manufacturer's Certificate: Certify products meet or exceed specified requirements.

F. Samples:

1. Submit 12 x 12 inches in size illustrating each type of specified finished aluminum surface.

2. Submit 12-inch length of frame profile in any throat size and finish. Division 1 criteria for sample quantity do not apply: one sample required only.

1.4 QUALITY ASSURANCE

A. Manufacturer and Installer: Companies specializing in manufacturing and installing aluminum door and glazing frame systems with minimum five years’ experience.

B. Fire-Rated Assemblies: Whenever a fire-resistance classification is indicated, provide fire-rated frames investigated, tested, and labeled as part of a fire door or fire window assembly to certify compliance with the requirements of UL 10C Positive Pressure Test for specified exposure by an agency acceptable to governing authorities.

1. Labels: Provide labels permanently fastened on each fire rated frame that are within size limits established by NFPA and the testing authority.

2. Installation: Install assemblies in compliance with NFPA 80 and as specified herein.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Packing, Shipping, Handling, and Unloading: Package interior aluminum frames work in cardboard or other containers with separators, banding, spreaders, and paper wrappings to protect items during transit and Project site storage.

B. Identification: Mark frame, on a surface which will be hidden after installation, with designation of opening for which it is furnished.

1.6 COORDINATION

A. Hardware Suppliers: Furnish interior aluminum frame manufacturer with accepted hardware schedule, hardware templates, and samples of physical hardware where necessary to ensure correct fitting and installation.

1.7 WARRANTY

A. Division 1 - Execution and Closeout Requirements: Product warranties and product bonds. Warranties shall pay for all costs associated with repairs and replacement upon notification of defects.

B. Material Warranty: Provide material manufacturer’s product warranty for a minimum of two (2) years from date of Substantial Completion.

ADVANCE DESIGN CONSULTANTS INC.

04/27/2018 08 12 16 - 3

C. Material Warranty: Provide material manufacturer’s product warranty that finish will not contain defects including cracking, flaking, blistering, peeling and excessive fading, chalking and non-uniformity in color for a minimum of five (5) years from date of Substantial Completion.

PART 2 – PRODUCTS

2.1 ALUMINUM DOOR AND GLAZING FRAMES

A. Manufacturers: Provide compliant products of one of the following or approved equal.

1. Frameworks / Assa Abloy.

2. RACO Interior Products, Incorporated.

3. Wilson Partitions.

B. Product Description: Wilson Partitions’ “Series 200” is the Basis of the Specification.

Extruded aluminum frames, non-rated and rated, either fabricated to required throat sizes or furnished with expandable throat to required sizes. Snap-on rectilinear trim with 1-1/2 inch wide flush profile. Frame shall accept 1/4 inch or 3/8 inch glass.

2.2 COMPONENTS

A. Aluminum: ASTM B221; 6063 alloy, T5 temper. Not less than 25 percent pre-consumer recycled content.

B. Fasteners: Aluminum, nonmagnetic, stainless-steel or other noncorrosive metal fasteners compatible with frames, stops, panels, reinforcement plates, hardware, anchors, and other items being fastened.

C. Door Silencers: Manufacturer's standard continuous mohair, wool pile, or vinyl seals.

D. Glazing Gaskets: Manufacturer's standard extruded or molded plastic, to accommodate glazing thickness indicated.

E. Glass: As indicated on Drawings and specified in Section 08 80 00.

F. Hardware: As specified in Section 08 71 00.

2.3 FABRICATION

A. Pre-machine jambs and prepare for hardware, with concealed reinforcement plates, drilled and tapped as required, and fastened within the frame.

B. Provide corner reinforcements and alignment clips for precise butt or mitered connections.

C. Fabricate all components to allow secure installation without exposed fasteners.

ADVANCE DESIGN CONSULTANTS INC.

04/27/2018 08 12 16 - 4

D. Fabricate kits for glazing with removable stops to allow glazing replacement without dismantling.

E. Manufacturer shall pre-cut and ship all frame materials knock-down.

2.4 SHOP FINISHING

A. Clear Anodized Aluminum Surfaces: AAMA 611, AA-M12C22A31 non-specular as fabricated mechanical finish, medium matte chemical finish, and Architectural Class II clear anodized coating.

PART 3 – EXECUTION

3.1 EXAMINATION

A. Division 1 – Administrative Requirements: Coordination and project conditions.

B. Examine project conditions and verify that the work of this section may properly commence. Do not proceed with the installation until unsatisfactory conditions have been corrected.

C. Verify that the wall thickness does not exceed manufacturer’s recommended tolerances of specified frame throat size.

3.2 INSTALLATION

A. Comply with frame manufacturer’s printed installation instructions and approved shop drawings. Strictly adhere to maintaining specified wall thickness to insure dimension does not exceed frame throat size specified.

B. Install frames plumb and square, free from warp or twist. Securely anchor to substrates with fasteners recommended by frame manufacturer.

1. Use concealed installation clips to assure that splices and connections are tightly butted and properly aligned.

2. Secure clips to main structural extrusion components and not to snap-in or trim members.

3. Do not use screws or other fasteners that will be exposed to view when installation is complete.

4. Maintain dimensional tolerances and alignment with adjacent work. Ensure hairline joints and flush surfaces and with adjacent aluminum components.

3.3 CLEANING AND ADJUSTMENT

A. Division 1 – Execution and Closeout Requirements: Requirements for cleaning.

B. Clean work in accordance with manufacturer’s recommendations.

ADVANCE DESIGN CONSULTANTS INC.

04/27/2018 08 12 16 - 5

C. Touch up marred areas so that touch-up is not visible from a distance of 4 feet.

Remove and replace frames that cannot be satisfactorily adjusted.

3.4 PROTECTION

A. Protect installed work against damage from other construction work.

END OF SECTION