36C24727Q0073_2.pdf
PDF 507 KB Posted
- Solicitation number
- 36C24727Q0073
About this file
Solicitation Summary: One-Time Chiller Tube Cleaning Services
This is a Request for Quotation (RFQ) issued by the Department of Veterans Affairs (VA), VISN 7 Network Contracting Office, for one-time chiller tube cleaning services at the WJB Dorn VA Medical Center in Columbia, South Carolina. The solicitation number is 36C24727Q0073, with an offer due date of November 27, 2026, at 8:00 a.m. EST. This is a service-disabled veteran-owned small business (SDVOSB) set-aside, with a maximum contract value of $47 million. The contractor must provide all labor, supervision, travel, equipment, tools, supplies, materials, and incidental services to clean two Trane CVHF770 chillers, including draining and disassembly, tube cleaning using appropriate methods, Eddy Current testing with written reports, replacement of condenser automatic tube brush system brushes and basket clips (up to 25 baskets per chiller, maximum 50 total), reassembly, operational checks, and debris removal. Work must be completed within two months from award, performed Monday through Friday, 8:00 a.m. to 4:00 p.m., excluding weekends and federally observed holidays. The contractor shall check in and out with the Engineering Control Center and submit a comprehensive service report within ten business days of completion, documenting all work performed, testing results, replaced components, and any deficiencies identified.
Quotations are evaluated on three factors: technical capability and quality, past performance, and price. Offerors must submit a firm-fixed-price proposal covering all work, provide a technical approach addressing work sequence and safety procedures, demonstrate personnel qualifications with at least one HVAC technician experienced in commercial water-cooled chillers, submit a minimum of three past-performance references involving similar chiller maintenance services, and provide a compliance statement. A non-mandatory site visit is scheduled for November 10, 2026, at 9:00 a.m. EST. Questions must be submitted by November 13, 2026, at 8:00 a.m. EST. Invoices are submitted electronically upon completion and approved inspection through Tungsten Network, with payment by electronic funds transfer. The Government intends to award without discussions; therefore, offerors should submit their most favorable terms in initial offers.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| 36C24727Q0073 0001- Amendment.pdf 2.pdf | ||
| 36C24727Q0073 0001- Amendment.pdf | ||
| 36C24727Q0073_2.pdf | ||
| 36C24727Q0073_1.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
PAGE 1 OF 1. REQUISITION NO.
2. CONTRACT NO. 3. AWARD/EFFECTIVE DATE 4. ORDER NO. 5. SOLICITATION NUMBER 6. SOLICITATION ISSUE DATE
a. NAME b. TELEPHONE NO. (No Collect Calls) 8. OFFER DUE DATE/LOCAL
TIME
9. ISSUED BY CODE 10. THIS ACQUISITION IS UNRESTRICTED OR SET ASIDE: % FOR:
SMALL BUSINESS
HUBZONE SMALL
BUSINESS
SERVICE-DISABLED
VETERAN-OWNED
SMALL BUSINESS
WOMEN-OWNED SMALL BUSINESS
(WOSB) ELIGIBLE UNDER THE WOMEN-OWNED
SMALL BUSINESS PROGRAM
EDWOSB
8(A)
NAICS:
SIZE STANDARD:
11. DELIVERY FOR FOB DESTINA-
TION UNLESS BLOCK IS
MARKED
SEE SCHEDULE
12. DISCOUNT TERMS
13a. THIS CONTRACT IS A
RATED ORDER UNDER
DPAS (15 CFR 700)
13b. RATING
14. METHOD OF SOLICITATION
RFQ IFB RFP
15. DELIVER TO CODE 16. ADMINISTERED BY CODE
17a. CONTRACTOR/OFFEROR CODE FACILITY CODE 18a. PAYMENT WILL BE MADE BY CODE
TELEPHONE NO. UEI: EFT:
PHONE: FAX:
17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER
18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW IS CHECKED
SEE ADDENDUM
19. 20. 21. 22. 23. 24.
ITEM NO. SCHEDULE OF SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT
(Use Reverse and/or Attach Additional Sheets as Necessary)
25. ACCOUNTING AND APPROPRIATION DATA 26. TOTAL AWARD AMOUNT (For Govt. Use Only)
27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA ARE ARE NOT ATTACHED.
27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED
28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN _______________ 29. AWARD OF CONTRACT: REF. ___________________________________ OFFER COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DATED ________________________________. YOUR OFFER ON SOLICITATION DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY (BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED SET FORTH HEREIN IS ACCEPTED AS TO ITEMS:
30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)
30b. NAME AND TITLE OF SIGNER (TYPE OR PRINT) 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (TYPE OR PRINT) 31c. DATE SIGNED
AUTHORIZED FOR LOCAL REPRODUCTION (REV. NOV 2021)
PREVIOUS EDITION IS NOT USABLE Prescribed by GSA - FAR (48 CFR) 53.212
7. FOR SOLICITATION
INFORMATION CALL:
STANDARD FORM 1449
SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES
OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30
36C24727Q0073
36C24727Q0073 10-30-2026
Joseph E. Horn 404-431-6148 11-27-2026
8AM EST
36C247 Department of Veterans Affairs VISN 7 Network Contracting Office LaVista Business Park - Bldg A 2008 Weems Road Tucker GA 30084
X 100
X
561210
$47 Million
Net 30
N/A
X
36C544
See Delivery Address
Department of Veterans Affairs VISN 7 Network Contracting Office LaVista Business Park - Bldg A
FMS-VA-2(101)
Financial Services Center PO Box 149971 Austin TX 78714-9971
See CONTINUATION Page
One Time Chiller Tube Cleaning Service
VISN-7 VA MEDICAL CENTER
Vendor shall provide all material, travel, labor, and supervision required to perform One Time Chiller Tube Cleaning Service for Columbia VAMC in accordancie with attached Performance Work Statement / Statement of Work.
Questions shall be submitted by 11/13/2026 by 12pm EST.
Answers will be posted Est by 11/27/2026
Quoter shall be registered and active at System for Award Management (SAM) at https://www.sam.gov at the time of
POC for this RFQ is Joseph E. Horn, Joseph.Horn@va.gov
See CONTINUATION Page
X X
Joseph E. Horn Contract Officer
Table of Contents
SECTION A
A.1 SF 1449 SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL PRODUCTS
AND COMMERCIAL SERVICES
SECTION B - CONTINUATION OF SF 1449 BLOCKS
B.1 CONTRACT ADMINISTRATION DATA
B.2 STATEMENT OF WORK / PERFORMANCE WORK STATEMENT
B.3 PRICE/COST SCHEDULE
ITEM INFORMATION
B.4 DELIVERY SCHEDULE
SECTION C - CONTRACT CLAUSES
C.1 52.212-4 CONTRACT TERMS AND CONDITIONS—COMMERCIAL PRODUCTS
AND COMMERCIAL SERVICES (OCT 2025) (DEVIATION)
C.2 52.219-27 NOTICE OF SET-ASIDE FOR, OR SOLE-SOURCE AWARD TO,
SERVICE-DISABLED VETERAN-OWNED SMALL BUSINESS (SDVOSB) CONCERNS
ELIGIBLE UNDER THE SDVOSB PROGRAM (NOV 2025) (DEVIATION)
C.3 52.222-42 STATEMENT OF EQUIVALENT RATES FOR FEDERAL HIRES (MAY
2014)
C.4 52.222-90 ADDRESSING DEI DISCRIMINATION BY FEDERAL CONTRACTORS
(DEVIATION APR 2026)
C.5 52.223-23 SUSTAINABLE PRODUCTS (NOV 2025) (DEVIATION)
C.6 52.240-91 SECURITY PROHIBITIONS AND EXCLUSIONS (NOV 2025)
(DEVIATION)
C.7 VAAR 852.219-73 VA NOTICE OF TOTAL SET-ASIDE FOR CERTIFIED
SERVICE-DISABLED VETERAN-OWNED SMALL BUSINESSES (JAN 2023)
(DEVIATION)
C.8 VAAR 852.219-75 VA NOTICE OF LIMITATIONS ON SUBCONTRACTING—
CERTIFICATE OF COMPLIANCE FOR SERVICES AND CONSTRUCTION (JAN 2023)
(DEVIATION)
C.9 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998)
SECTION D - CONTRACT DOCUMENTS, EXHIBITS, OR ATTACHMENTS
D.1 WAGE DETERMINATION 2015-4429
SECTION E - SOLICITATION PROVISIONS
E.1 ADDENDUM to FAR 52.212-1 INSTRUCTIONS TO OFFERORS—COMMERCIAL
PRODUCTS AND COMMERCIAL SERVICES (DEVIATION AUG 2025)
E.2 ADDENDUM to 52.212-2 EVALUATION—COMMERCIAL PRODUCTS AND
COMMERCIAL SERVICES (DEVIATION AUG 2025)
E.3 52.216-1 TYPE OF CONTRACT (NOV 2025) (DEVIATION)
E.4 52.240-90 SECURITY PROHIBITIONS AND EXCLUSIONS REPRESENTATIONS
AND CERTIFICATIONS (NOV 2025) (DEVIATION)
E.5 52.252-1 SOLICITATION PROVISIONS INCORPORATED BY REFERENCE (FEB
1998)
SECTION B - CONTINUATION OF SF 1449 BLOCKS
B.1 CONTRACT ADMINISTRATION DATA
1. Contract Administration: All contract administration matters will be handled by the following individuals:
a. CONTRACTOR:
b. GOVERNMENT: Contracting Officer 36C247 Joseph E. Horn
VISN 7 Network Contracting Office LaVista Business Park - Bldg A
2. CONTRACTOR REMITTANCE ADDRESS: All payments by the Government to the contractor will be made in accordance with:
[X] 52.232-33, Payment by Electronic Funds Transfer—System For Award Management, or
[] 52.232-36, Payment by Third Party
3. INVOICES: Invoices shall be submitted in arrears:
a. Quarterly []
b. Semi-Annually []
c. Other [x] Upon Completion and Approved Inspection
4. GOVERNMENT INVOICE ADDRESS: All Invoices from the contractor shall be submitted electronically in accordance with VAAR Clause 852.232-72 Electronic Submission of Payment Requests.
VA.Registration@Tungsten-Network.com https://www.fsc.va.gov/einvoice.asp
ACKNOWLEDGMENT OF AMENDMENTS: The offeror acknowledges receipt of amendments to the Solicitation numbered and dated as follows:
AMENDMENT NO DATE
https://www.fsc.va.gov/einvoice.asp
B.2 STATEMENT OF WORK / PERFORMANCE WORK STATEMENT
One-Time Chiller Tube Cleaning Services
1. General Information
1.1 Requirement
The Department of Veterans Affairs, Columbia Healthcare System, WJB Dorn VA Medical Center, requires one-time chiller tube cleaning services for two chillers located in the facility’s Chiller Plant.
The Contractor shall provide all labor, supervision, travel, equipment, tools, supplies, materials, and incidental services necessary to complete the work described in this Statement of Work/Performance Work Statement (SOW/PWS).
1.2 Facility Background
The WJB Dorn VA Medical Center is a 216-bed medical facility providing acute medical, surgical, psychiatric, and long-term care services. The facility is located in Columbia, South Carolina, and provides primary, secondary, and selected tertiary care.
2. Place of Performance
WJB Dorn VA Medical Center 6439 Garners Ferry Road Columbia, SC 29209
Work will be performed in the facility’s Chiller Plant.
3. Period and Hours of Performance
3.1 Period of Performance
The period of performance shall begin on the date of contract award and shall not exceed two months.
3.2 Normal Working Hours
Work shall be performed Monday through Friday, between 8:00 a.m. and 4:00 p.m., excluding weekends and federally observed holidays.
Overtime is not authorized unless approved in writing by the Contracting Officer.
3.3 Federal Holidays
The following federally observed holidays shall be excluded from the normal hours of performance:
• New Year’s Day — January 1
• Birthday of Martin Luther King, Jr. — Third Monday in January
• Washington’s Birthday — Third Monday in February
• Memorial Day — Last Monday in May
• Juneteenth National Independence Day — June 19
• Independence Day — July 4
• Labor Day — First Monday in September
• Columbus Day — Second Monday in October
• Veterans Day — November 11
• Thanksgiving Day — Fourth Thursday in November
• Christmas Day — December 25
When a holiday falls on a weekend, the federally observed holiday will apply.
4. Government Points of Contact
A Contracting Officer’s Representative (COR) and/or Alternate Contracting Officer’s Representative (ACOR) will be designated for this requirement. Written notification of the designated COR/ACOR will be provided to the Contractor after award.
The Contractor shall coordinate all scheduling and access requirements through the designated
COR/ACOR.
The Contractor shall not make changes to the scope, schedule, equipment requirements, or other contract terms without written authorization from the Contracting Officer.
5. Equipment Covered by This Requirement
The Contractor shall provide cleaning and related services for the following Trane chillers:
Chiller Manufacturer Model Serial Number Chiller No. 1 Trane CVHF770 L03M08208 Chiller No. 2 Trane CVHF770 L08L05174
6. Scope of Work
The Contractor shall complete a one-time service for each chiller. The work shall include, at a minimum, the following:
6.1 Safety and Preparation
a. Coordinate the work schedule with the COR/ACOR.
b. Perform all required lockout/tagout procedures before beginning work.
c. Clearly barricade or block off the work area before work begins and maintain the barricades throughout the work as necessary to prevent unauthorized personnel from entering or disrupting the work area.
d. Protect Government property and surrounding equipment from damage, contamination, or other adverse conditions resulting from the work.
e. Secure all tools, equipment, materials, and work areas during breaks, lunch periods, and at the end of each workday.
6.2 Draining and Disassembly
For each chiller, the Contractor shall:
a. Drain the evaporator and condenser as required to perform the work.
b. Remove the heads from both ends of the condenser.
c. Remove piping as necessary to facilitate access and cleaning.
d. Remove only one head from the evaporator.
e. Properly protect, store, and preserve removed components during the work.
6.3 Tube Cleaning and Testing
The Contractor shall:
a. Clean the condenser and evaporator tubes using methods appropriate for the equipment and consistent with applicable industry standards and manufacturer recommendations.
b. Perform Eddy Current testing of the tubes.
c. Provide the Government with a written Eddy Current testing report identifying the equipment tested, test results, deficiencies, and any tubes or areas requiring attention.
d. Notify the COR/ACOR of any condition that may affect safe operation, reliability, or continued service of either chiller.
6.4 Automatic Tube Brush System
For each chiller, the Contractor shall:
a. Replace the brushes in the condenser automatic tube brush system.
b. Provide brushes compatible with the automatic tube brushing systems manufactured by Water Technology of Pensacola, Inc.
c. Replace the basket clips on each condenser basket.
d. Replace up to 25 baskets per chiller, for a maximum total of 50 baskets for both chillers.
e. Provide replacement components that are compatible with the existing automatic tube brush systems.
6.5 Reassembly and Operational Check
The Contractor shall:
a. Reinstall the condenser and evaporator heads.
b. Reinstall all piping removed during the work.
c. Ensure that components are properly aligned, secured, and sealed.
d. Remove all tools, materials, packaging, and debris from the work area.
e. Check the operation of each chiller after completing the work.
f. Report any abnormal operating condition, leak, damage, deficiency, or other area of concern to the COR/ACOR before demobilization.
7. Contractor Responsibilities
The Contractor shall furnish all labor, supervision, transportation, travel, equipment, tools, supplies, materials, replacement components, and incidental services required to perform the work.
The Contractor shall:
• Perform the work in a professional and workmanlike manner.
• Comply with applicable federal, state, and local safety requirements.
• Use qualified personnel experienced in servicing commercial water-cooled chillers.
• Protect the facility, equipment, and occupants during performance.
• Maintain a clean and orderly work area.
• Remove all debris generated by the work from the facility at the end of each workday.
• Promptly notify the COR/ACOR of conditions that prevent or delay performance.
• Obtain approval from the COR/ACOR before proceeding with work that is outside the stated scope.
8. Check-In and Check-Out Requirements
The Contractor and all Contractor service personnel shall check in and out with the Engineering Control Center (ECC), Building 100, before beginning and upon completion of required services.
This requirement is necessary to establish the location and contact information of Contractor personnel while they are working at the facility and to support emergency communications during normal working hours.
9. Safety and Site Requirements
9.1 Lockout/Tagout
The Contractor shall perform all required lockout/tagout procedures before beginning work.
Lockout/tagout activities shall be conducted by trained and authorized personnel in accordance with applicable requirements.
9.2 Work Area Control
The Contractor shall clearly identify and barricade the work area. Tools, equipment, and materials shall not be left unsecured in open or accessible areas.
9.3 Tools and Equipment
Tools and equipment shall be removed from open areas or stored in a secure location during breaks, lunch periods, and at the end of each workday.
9.4 Debris and Housekeeping
The Contractor shall maintain the work area in a clean and orderly condition. All debris, waste, removed materials, and packaging generated by the Contractor shall be removed from the facility upon completion of service each day, unless otherwise directed by the COR/ACOR.
9.5 Smoking
The WJB Dorn VA Medical Center is a smoke-free campus. Smoking is prohibited on the campus.
10. Personnel Qualifications and Training
All personnel assigned to perform the work shall meet the following minimum requirements:
a. Possess current 10-hour Occupational Safety and Health Administration (OSHA) training applicable to the work performed.
b. Be qualified to perform the assigned duties.
c. Include at least one qualified HVAC technician with experience servicing commercial water-cooled chillers.
d. Be capable of performing required lockout/tagout procedures and other applicable safety practices.
The Contractor shall provide evidence of qualifications or training upon request by the Contracting Officer or COR.
11. Deliverables and Reporting Requirements
11.1 Service Report
The Contractor shall provide a written service report after all work has been completed. The report shall be submitted to the COR no later than ten business days after completion of the applicable inspection or service activity.
The service report shall include, at a minimum:
• Date or dates work was performed
• Chiller numbers
• Manufacturer, model, and serial number of each chiller serviced
• Description of work performed on each chiller
• Tube-cleaning methods used
• Eddy Current testing results
• Identification of replaced brushes, basket clips, and baskets
• Any areas of concern, deficiencies, leaks, damage, or recommended follow-up work
• Operational-check results
• Names of the technicians who performed the work
• Date the report was prepared
• Contractor’s name and contact information
11.2 Eddy Current Testing Report
The Eddy Current testing report shall be submitted with the service report and shall identify:
• Chiller and heat exchanger tested
• Date of testing
• Testing method and equipment used
• Test results
• Tube or location identification, where applicable
• Deficiencies or indications detected
• Recommendations for corrective action, if applicable
11.3 Government Review
Submission of a report does not relieve the Contractor of responsibility for completing the work in accordance with the contract. The Government may request clarification or additional supporting information when necessary to evaluate the completed services.
12. Site Visit
Although attendance is not mandatory, a site visit may be offered, and prospective Contractors are strongly encouraged to attend.
The date and time of any site visit will be coordinated by the Contracting Officer and COR and identified in the solicitation.
Questions will not be answered during the site visit. All questions must be submitted in writing to the Contracting Point of Contact identified in the solicitation. Questions and Government responses may be issued through an amendment to the solicitation.
13. Past Performance
The Contractor shall submit a minimum of three past-performance references for projects involving a similar scope of work. The references should demonstrate experience with commercial water-cooled chiller tube cleaning, Eddy Current testing, automatic tube brush systems, or comparable chiller maintenance services.
Each past-performance submission should include, at a minimum:
• Customer or agency name
• Contract or purchase order number, if applicable
• Brief description of the work performed
• Contract or project value
• Period of performance
• Customer point of contact
• Telephone number and email address
• Description of the Contractor’s role and responsibilities
14. Invoicing and Payment
14.1 Electronic Invoicing
Payment will be made upon receipt and acceptance of a properly prepared, detailed invoice submitted through Tungsten Network, formerly known as OB10:
https://www.tungsten-network.com/customer-campaigns/veteransaffairs/
The Contractor shall submit invoices in accordance with applicable contract provisions and instructions provided by the Department of Veterans Affairs.
14.2 Invoice Requirements
A properly prepared invoice shall include:
• Invoice number and date
• Contractor’s legal name and address
• Accurate purchase order or contract number
• Description of the supplies or services provided
• Period during which the services were provided
• Total amount due
• Any additional information required by the contract or Tungsten Network
14.3 Tungsten Network Contacts
• Tungsten e-Invoice Setup Information: 1-877-489-6135
• Tungsten e-Invoice Email: VA.Registration@Tungsten-Network.com
• Financial Services Center e-Invoice Contact: 1-877-353-9791
• Financial Services Center Email: vafsccshd@va.gov
• Website: https://www.fsc.va.gov/einvoice.asp
15. Records Management
The Contractor shall comply with applicable federal records-management requirements and Department of Veterans Affairs policies concerning records created, received, maintained, or delivered under this contract.
Applicable authorities include, but are not limited to:
• 44 U.S.C. Chapters 21, 29, 31, and 33
• Freedom of Information Act, 5 U.S.C. § 552
• Privacy Act of 1974, 5 U.S.C. § 552a
• 36 C.F.R. Parts 1222 and 1228
The following requirements apply:
https://www.tungsten-network.com/customer-campaigns/veteransaffairs/ mailto:VA.Registration@Tungsten-Network.com mailto:vafsccshd@va.gov https://www.fsc.va.gov/einvoice.asp
a. All deliverables produced under the contract shall be treated as Government property. The Government shall have unlimited rights to use, dispose of, or disclose the data contained in the deliverables as determined to be in the public interest.
b. The Contractor shall not create or maintain records using Government information technology equipment or Government records unless the records are specifically authorized by or directly related to performance of the contract.
c. The Contractor shall not retain, use, sell, disseminate, or otherwise distribute copies of deliverables containing information protected by the Privacy Act or information generally protected from disclosure under the Freedom of Information Act.
d. The Government owns the rights to all data and records produced as part of this contract, including electronic data, electronic information systems, electronic databases, and supporting documentation created under the contract.
e. The Contractor shall provide sufficient technical documentation with electronic data deliverables to permit the Government to access and use the data.
f. The Contractor shall comply with applicable federal and agency records-management policies, including policies concerning the safeguarding and preservation of records covered by the Privacy Act.
g. The Contractor shall preserve records created or received in connection with the contract regardless of format, including paper and electronic records, mode of transmission, or state of completion, including drafts and final versions.
h. The Contractor shall not dispose of, destroy, alter, remove, or otherwise alienate contract records without the prior written approval of the Contracting Officer.
i. Records shall not be removed from the legal custody of the Government or destroyed except in accordance with applicable federal records schedules and written authorization from the Contracting Officer.
Willful and unlawful destruction, damage, or alienation of federal records may be subject to applicable fines and penalties, including those referenced in 18 U.S.C. § 2701.
16. Termination for Convenience
In accordance with Federal Acquisition Regulation (FAR) 52.212-4(l), the Government reserves the right to terminate this contract, or any part of the contract, for its sole convenience.
17. Completion and Acceptance
The services will be considered complete when the Contractor has:
• Completed the required work on both identified chillers;
• Completed required tube cleaning and Eddy Current testing;
• Installed the required brushes, basket clips, and baskets;
• Reinstalled removed heads and piping;
• Completed operational checks;
• Removed tools, materials, and debris from the work area;
• Submitted the required service and Eddy Current testing reports; and
• Corrected deficiencies identified by the Government that are within the scope of the contract.
Final acceptance is subject to Government inspection and approval by the authorized Government representative.
B.3 PRICE/COST SCHEDULE
ITEM INFORMATION
ITEM
NUMBER
DESCRIPTION OF
SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT
1.00 JB __________________ __________________
Provide all labor, supervision, equipment, materials, parts, and incidental services necessary to perform a one-time service for cleaning the chiller plant chiller tubes at the Columbia Healthcare System, WJB Dorn VA Medical Center, Columbia, South Carolina. The work shall include:
Furnishing parts and materials required for condensate/chiller cleaning.
Furnishing tube brushes, clips, baskets, and related accessories.
Performing eddy current testing of the chiller tubes.
Providing labor to clean the chiller tubes and remove and replace parts as required.
Cleaning the work area and disposing of waste and removed materials in accordance with applicable federal, state, and local requirements.
Providing a service report documenting work performed, parts replaced, eddy current testing results, deficiencies identified, and recommendations in accordance with PWS/SOW
GRAND TOTAL
B.4 DELIVERY SCHEDULE
ITEM
NUMBER PLACE OF PERFORMANCE QUANTITY
DELIVERY
DATE
1.00 60 Days ARO
SECTION C - CONTRACT CLAUSES
C.1 52.212-4 CONTRACT TERMS AND CONDITIONS—COMMERCIAL
PRODUCTS AND COMMERCIAL SERVICES (OCT 2025) (DEVIATION)
(a) Definitions. The clause at Federal Acquisition Regulation (FAR) 52.202-1, Definitions, is incorporated by reference.
(b) Inspection/Acceptance. The Contractor shall only tender for acceptance those items that conform to the requirements of this contract. The Government reserves the right to inspect or test any supplies or services that have been tendered for acceptance. The Government may require repair or replacement of nonconforming supplies or reperformance of nonconforming services at no increase in contract price. If repair/replacement or reperformance will not correct the defects or is not possible, the Government may seek an equitable price reduction or adequate consideration for acceptance of nonconforming supplies or services. The Government must exercise its post acceptance rights—
(1) Within a reasonable time after the defect was discovered or should have been discovered;
and
(2) Before any substantial change occurs in the condition of the item, unless the change is due to the defect in the item.
(c) Assignment. The Contractor or its assignee may assign its rights to receive payment due as a result of performance of this contract to a bank, trust company, or other financing institution, including any Federal lending agency in accordance with the Assignment of Claims Act (31 U.S.C. 3727). However, when a third party makes payment (e.g., use of the Governmentwide commercial purchase card), the Contractor may not assign its rights to receive payment under this contract.
(d) Changes. Changes in the terms and conditions of this contract may be made only by written agreement of the parties.
(e) Disputes. This contract is subject to 41 U.S.C. chapter 71, Contract Disputes. Failure of the parties to this contract to reach agreement on any request for equitable adjustment, claim, appeal or action arising under or relating to this contract shall be a dispute to be resolved in accordance with the clause FAR 52.233-1, Disputes, which is incorporated in this contract by reference. The Contractor shall proceed diligently with performance of this contract, pending final resolution of any dispute arising under the contract.
(f) Excusable delays. The Contractor shall be liable for default unless nonperformance is caused by an occurrence beyond the reasonable control of the Contractor and without its fault or negligence. Examples of occurrences include acts of God or the public enemy, acts of the Government in either its sovereign or contractual capacity, fires, floods, epidemics, quarantine restrictions, strikes, unusually severe weather, and delays of common carriers. When an excusable delay occurs, the Contractor shall—
(1) Notify the Contracting Officer in writing as soon as possible;
(2) Remedy the delay as quickly as possible; and
(3) Notify the Contracting Officer when the occurrence is over.
(g) Invoice. The Government will handle invoices according to the Prompt Payment Act (31 U.S.C. 3903) and 5 CFR part 1315. The Contractor shall submit invoices to the address designated in the contract to receive invoices. An invoice must include the information required by 5 CFR part 1315.9(b).
(h) Patent indemnity. The Contractor shall indemnify the Government and its officers, employees, and agents against liability, including costs, for actual or alleged direct or contributory infringement of, or inducement to infringe, any United States or foreign patent, trademark, or copyright, arising out of the performance of this contract, provided the Contractor is reasonably notified of such claims and proceedings.
(i) Payment—
(1) Items accepted. Payment shall be made for items accepted by the Government that have been delivered to the delivery destinations set forth in this contract.
(2) Prompt payment. The Government will make payment in accordance with the Prompt Payment Act (31 U.S.C. 3903) and prompt payment regulations at 5 CFR part 1315.
(3) Discount. In connection with any discount offered for early payment, time shall be computed from the date of the invoice. For the purpose of computing the discount earned, payment shall be considered to have been made on the date that appears on the payment check or the specified payment date if an electronic funds transfer payment is made.
(4) Overpayments. If the Contractor becomes aware of a duplicate contract financing or invoice payment or that the Government has otherwise overpaid on a contract financing or invoice payment, the Contractor shall—
(i) Remit the overpayment amount to the payment office cited in the contract along with a description of the overpayment including the—
(A) Circumstances of the overpayment (e.g., duplicate payment, erroneous payment, liquidation errors, date(s) of overpayment);
(B) Affected contract number and delivery order number, if applicable;
(C) Affected line item or subline item, if applicable;
(D) Contractor point of contact; and
(ii) Provide a copy of the remittance and supporting documentation to the Contracting Officer.
(5) Interest.
(i) All amounts that become payable by the Contractor to the Government under this contract shall bear simple interest from the date due until paid unless paid within 30 days of becoming due. The interest rate shall be the interest rate established by the Secretary of the
Treasury as provided in 41 U.S.C. 7109, which is applicable to the period in which the amount becomes due, as provided in (i)(6)(v) of this clause, and then at the rate applicable for each six-month period as fixed by the Secretary until the amount is paid.
(ii) The Government may issue a demand for payment to the Contractor upon finding a debt is due under the contract.
(iii) Final decisions. The Contracting Officer will issue a final decision as required by FAR part 33 if—
(A) The Contracting Officer and the Contractor are unable to reach agreement on the existence or amount of a debt within 30 days;
(B) The Contractor fails to liquidate a debt previously demanded by the Contracting Officer within the timeline specified in the demand for payment unless the amounts were not repaid because the Contractor has requested an installment payment agreement; or
(C) The Contractor requests a deferment of collection on a debt previously demanded by the Contracting Officer (see FAR part 32).
(iv) If a demand for payment was previously issued for the debt, the demand for payment included in the final decision shall identify the same due date as the original demand for payment.
(v) Amounts shall be due at the earliest of the following dates:
(A) The date fixed under this contract.
(B) The date of the first written demand for payment, including any demand for payment resulting from a termination for cause.
(vi) The interest charge shall be computed for the actual number of calendar days involved beginning on the due date and ending on-
(A) The date on which the designated office receives payment from the Contractor;
(B) The date of issuance of a Government check to the Contractor from which an amount otherwise payable has been withheld as a credit against the contract debt; or
(C) The date on which an amount withheld and applied to the contract debt would otherwise have become payable to the Contractor.
(vii) The interest charge made under this clause may be reduced under the procedures for interest credits prescribed in FAR part 32 in effect on the date of this contract.
(j) Risk of loss. Unless the contract specifically provides otherwise, risk of loss or damage to the supplies provided under this contract shall remain with the Contractor until, and shall pass to the Government upon—
(1) Delivery of the supplies to a carrier, if transportation is f.o.b. origin; or
(2) Delivery of the supplies to the Government at the destination specified in the contract, if transportation is f.o.b. destination.
(k) Taxes. The contract price includes all applicable Federal, State, and local taxes and duties.
(l) Termination for the Government's convenience. The Government reserves the right to terminate this contract, or any part hereof, for its sole convenience. In the event of such termination, the Contractor shall immediately stop all work and shall immediately cause any and all of its suppliers and subcontractors to cease work. Subject to the terms of this contract, the Contractor shall be paid a percentage of the contract price reflecting the percentage of the work performed prior to the notice of termination, plus reasonable charges the Contractor can demonstrate to the satisfaction of the Government using its standard record keeping system, have resulted from the termination. The Contractor shall not be required to comply with the cost accounting standards or contract cost principles for this purpose. This paragraph does not give the Government any right to audit the Contractor's records. The Contractor shall not be paid for any work performed or costs incurred which reasonably could have been avoided.
(m) Termination for cause. The Government may terminate this contract, or any part hereof, for cause in the event of any default by the Contractor, or if the Contractor fails to comply with any contract terms and conditions, or fails to provide the Government, upon request, with adequate assurances of future performance. The Government will send a cure notice to the Contractor, unless the reason for the termination is late delivery. In the event of termination for cause, the Government shall not be liable to the Contractor for any amount for supplies or services not accepted, and the Contractor shall be liable to the Government for any and all rights and remedies provided by law. If it is determined that the Government improperly terminated this contract for default, such termination shall be deemed a termination for convenience.
(n) Title. Unless specified elsewhere in this contract, title to items furnished under this contract shall pass to the Government upon acceptance, regardless of when or where the Government takes physical possession.
(o) Warranty. The Contractor warrants and implies that the items delivered under this contract are merchantable and fit for use for the particular purpose described in this contract.
(p) Limitation of liability. Except as otherwise provided by an express warranty, the Contractor will not be liable to the Government for consequential damages resulting from any defect or deficiencies in accepted items.
(q) Compliance with laws unique to Government contracts. The Contractor agrees to comply with 31 U.S.C. 1352 relating to limitations on the use of appropriated funds to influence certain Federal contracts; 40 U.S.C. chapter 37, Contract Work Hours and Safety Standards; 41 U.S.C.
chapter 87, Kickbacks; 49 U.S.C. 40118, Government-financed air transportation; and 41 U.S.C.
chapter 21 relating to procurement integrity.
(r) Order of precedence. Any inconsistencies in this solicitation or contract shall be resolved by giving precedence in the following order:
(1) The schedule of supplies/services.
(2) The Disputes, Payments, Invoice, Compliance with Laws Unique to Government Contracts, and Unauthorized Obligations paragraphs of this clause;
(3) Other contract clauses incorporated in the solicitation or contract;
(4) Addenda to this solicitation or contract,
(5) Solicitation provisions incorporated in the solicitation.
(6) Other paragraphs of this clause.
(7) Other documents, exhibits, and attachments; and
(8) The specification.
(s) Unauthorized obligations.
(1) Except as stated in paragraph (s)(2) of this clause, when any supply or service acquired under this contract is subject to any End User License Agreement (EULA), Terms of Service (TOS), or similar legal instrument or agreement, that includes any clause requiring the Government to indemnify the Contractor or any person or entity for damages, costs, fees, or any other loss or liability that would create an Anti-Deficiency Act violation (31 U.S.C. 1341), the following shall govern:
(i) Any such clause is unenforceable against the Government.
(ii) Neither the Government nor any Government-authorized end user shall be deemed to have agreed to such clause by virtue of it appearing in the EULA, TOS, or similar legal instrument or agreement. If the EULA, TOS, or similar legal instrument or agreement is invoked through an “I agree” click box or other comparable mechanism (e.g., “click-wrap” or “browse-wrap” agreements), execution does not bind the Government or any Government authorized end user to such clause.
(iii) Any such clause is deemed to be stricken from the EULA, TOS, or similar legal instrument or agreement.
(2) Paragraph (s)(1) of this clause does not apply to indemnification by the Government that is expressly authorized by statute and specifically authorized under applicable agency regulations and procedures.
(t) Comptroller General examination of record. This paragraph applies if this contract was awarded using other than sealed bid procedures and is in excess of the simplified acquisition threshold on the date of award of this contract.
(1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor’s directly pertinent records involving transactions related to this contract.
(2) The Contractor shall make available at its offices, at all reasonable times, the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR part 4, longer period required by statute, or periods specified in other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved.
(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This clause does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.
(u) Incorporation by reference. The Contractor’s representations and certifications, including those completed electronically via the System for Award Management (SAM), are incorporated by reference into the contract.
(End of Clause)
C.2 52.219-27 NOTICE OF SET-ASIDE FOR, OR SOLE-SOURCE AWARD
TO, SERVICE-DISABLED VETERAN-OWNED SMALL BUSINESS (SDVOSB)
CONCERNS ELIGIBLE UNDER THE SDVOSB PROGRAM (NOV 2025)
(DEVIATION)
(a) Definition.
Service-disabled veteran-owned small business (SDVOSB) concern means a small business concern—
(1)(i) Not less than 51 percent of which is owned and controlled by one or more service-disabled veterans or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more service-disabled veterans; and
(ii) The management and daily business operations of which are controlled by one or more service-disabled veterans or, in the case of a service-disabled veteran with permanent and severe disability, the spouse or permanent caregiver of such veteran; or
(2) A small business concern eligible under the SDVOSB Program in accordance with 13 CFR part 128 (see FAR 19.106).
(3) Service-disabled veteran, as used in this definition, means a veteran as defined in 38 U.S.C. 101(2), with a disability that is service-connected, as defined in 38 U.S.C. 101(16) and who is registered in the Beneficiary Identification and Records Locator Subsystem, or successor system that is maintained by the Department of Veterans Affairs’ Veterans Benefits Administration, as a service-disabled veteran.
Service-disabled veteran-owned small business (SDVOSB) concern eligible under the SDVOSB Program means an SDVOSB concern that is designated in the System for Award Management (SAM) as certified by the Small Business Administration (SBA) in accordance with
13 CFR 128.300.
Service-disabled veteran-owned small business (SDVOSB) Program means a program that authorizes contracting officers to limit competition, including award on a sole-source basis, to SDVOSB concerns eligible under the SDVOSB Program.
(b) Applicability. This clause applies only to—
(1) Contracts that have been set aside for, or awarded on a sole-source basis to, SDVOSB concerns eligible under the SDVOSB Program;
(2) Part or parts of a multiple-award contract that have been set aside for SDVOSB concerns eligible under the SDVOSB Program; and
(3) Orders set aside for SDVOSB concerns eligible under the SDVOSB Program, under multiple-award contracts as described in 8.4 and 16.5.
(c) General.
(1) Offers are solicited only from concerns designated in SAM as SDVOSB concerns certified by SBA. Offers received from concerns that are not SDVOSB concerns certified by SBA will not be considered.
(2) Any award resulting from this solicitation will be made only to a concern designated in SAM as an SDVOSB certified by SBA.
(d) A joint venture may be considered an SDVOSB concern if the managing partner of the joint venture complies with the criteria defined in paragraph (a) of this clause and 13 CFR 128.402.
(e) In a joint venture that complies with paragraph (d) of this clause, the SDVOSB party or parties to the joint venture shall perform at least 40 percent of the work performed by the joint venture. Work performed by the SDVOSB party or parties to the joint venture must be more than administrative functions.
(End of Clause)
C.3 52.222-42 STATEMENT OF EQUIVALENT RATES FOR FEDERAL HIRES
(MAY 2014)
In compliance with the Service Contract Labor Standards statute and the regulations of the Secretary of Labor (29 CFR Part 4), this clause identifies the classes of service employees expected to be employed under the contract and states the wages and fringe benefits payable to each if they were employed by the contracting agency subject to the provisions of 5 U.S.C.5341 or 5332.
This Statement is for Information Only:
It is not a Wage Determination
Employee Class Monetary Wage-Fringe Benefits HVAC Mechanic / Chiller Mechanic 29.33
Maintenance Mechanic, WG 22.53
General Laborer, WG 18.07
C.4 52.222-90 ADDRESSING DEI DISCRIMINATION BY FEDERAL
CONTRACTORS (DEVIATION APR 2026)
(a)Definitions. As used in this clause—
Program participation means membership or participation in, or access or admission to:
training, mentoring, or leadership development programs; educational opportunities; clubs;
associations; or similar opportunities that are sponsored or established by the contractor or subcontractor.
Racially discriminatory diversity, equity, and inclusion (DEI) activities means disparate treatment based on race or ethnicity in the recruitment, employment (e.g., hiring, promotions), contracting (e.g., vendor agreements), program participation, or allocation or deployment of an entity's resources.
(b) In connection with the performance of work under this contract, the Contractor agrees as follows:
(1) The Contractor will not engage in any racially discriminatory DEI activities;
(2) The Contractor will furnish all information and reports, including providing access to books, records, and accounts, as required by the Contracting Officer, for purposes of ascertaining compliance with this clause;
(3) In the event of the Contractor's or a subcontractor's noncompliance with this clause, this contract may be canceled, terminated, or suspended in whole or in part, and the Contractor or subcontractor may be declared ineligible for further Government contracts;
(4) The Contractor will report any subcontractor's known or reasonably knowable conduct that may violate this clause to the Contracting Officer and take any appropriate remedial actions directed by the Contracting Officer; and
(5) The Contractor will inform the Contracting Officer if a subcontractor sues the Contractor and the suit puts at issue, in any way, the validity of this clause.
(6) The Contractor recognizes that compliance with the requirements of this clause are material to the Government's payment decisions for purposes of 31 U.S.C. 3729(b)(4).
(c) The Contractor must include the substance of this clause, including this paragraph (c), in subcontracts at any tier, including those for commercial products and commercial services, except those where the place of delivery or performance is outside the United States.
C.5 52.223-23 SUSTAINABLE PRODUCTS (NOV 2025) (DEVIATION)
(a) Definitions. As used in this clause—
Sustainable products means—
(1) A product that contains recovered material designated by the EPA under the Comprehensive Procurement Guidelines (42 U.S.C. 6962) (40 CFR part 247) (https://www.epa.gov/smm/comprehensive-procurement-guideline-cpg-program#products).
(2) An energy-efficient product or low standby power device (42 U.S.C. 8259b) (10 CFR part 436, subpart C) (https://www.energy.gov/femp/search-energy-efficient-products, https://www.energystar.gov/products?s=mega, and https://www.energy.gov/femp/low-standby-power-product-list).
(3) A biobased product that meets the content requirements of the USDA under the BioPreferred® program (7 U.S.C. 8102) (7 CFR Part 4270) (https://www.biopreferred.gov/)
(4) A substance identified in the EPA’s Significant New Alternatives Policy (SNAP) program as a safe alternative to an ozone-depleting substance (42 U.S.C. 7671l) (40 CFR part 82, subpart G) (https://www.epa.gov/snap/unacceptable-and-acceptable-substitutes-tables).
(b) Requirements. The Government has identified in the statement of work or elsewhere in the contract the sustainable products that are required during the performance of this contract. The Contractor shall ensure that it provides sustainable products as required by this contract, when the products are—
(1) Delivered to the Government;
(2)Furnished for use by the Government;
(3) Incorporated into the construction of a public building or public work; or
(c) Furnished for use in performing services under this contract, where the cost of the products is a direct cost to this contract.
(End of Clause)
C.6 52.240-91 SECURITY PROHIBITIONS AND EXCLUSIONS (NOV 2025)
(DEVIATION)
(a) Definitions. As used in this clause—
American Security Drone Act-covered foreign entity means an entity included on a list that the Federal Acquisition Security Council (FASC) develops and maintains and publishes in the System for Award Management (SAM) at https://www.sam.gov (section 1822 of Pub. L. 118-31, 41 U.S.C. 3901 note prec.).
Backhaul means intermediate links between the core network, or backbone network, and the small subnetworks at the edge of the network (e.g., connecting cell phones/towers to the core telephone network). Backhaul can be wireless (e.g., microwave) or wired (e.g., fiber optic, coaxial cable, Ethernet).
https://www.epa.gov/smm/comprehensive-procurement-guideline-cpg-program#products https://www.energy.gov/femp/search-energy-efficient-products https://www.energystar.gov/products?s=mega https://www.energy.gov/femp/low-standby-power-product-list https://www.energy.gov/femp/low-standby-power-product-list https://www.biopreferred.gov/ https://www.epa.gov/snap/unacceptable-and-acceptable-substitutes-tables https://www.sam.gov
Covered application means the social networking service TikTok or any successor application or service developed or provided by ByteDance Limited or an entity owned by ByteDance Limited.
Covered article, as defined in 41 U.S.C. 4713(k), means:
(1) Information technology, as defined in 40 U.S.C. 11101, including cloud computing services of all types;
(2) Telecommunications equipment or telecommunications service, as those terms are defined in section 3 of the Communications Act of 1934 (47 U.S.C. 153);
(3) The processing of information on a Federal or non-Federal information system, subject to the requirements of the Controlled Unclassified Information program (see 32 CFR part 2002); or
(4) Hardware, systems, devices, software, or services that include embedded or incidental information technology.
Covered foreign country means The People’s Republic of China.
Covered telecommunications equipment or services means—
(1) Telecommunications equipment produced by Huawei Technologies Company or ZTE Corporation (or any subsidiary or affiliate of such entities);
(2) For the purpose of public safety, security of Government facilities, physical security surveillance of critical infrastructure, and other national security purposes, video surveillance and telecommunications equipment produced by Hytera Communications Corporation, Hangzhou Hikvision Digital Technology Company, or Dahua Technology Company (or any subsidiary or affiliate of such entities);
(3) Telecommunications or video surveillance services provided by such entities or using such equipment; or
(4) Telecommunications or video surveillance equipment or services produced or provided by an entity that the Secretary of Defense, in consultation with the Director of National Intelligence or the Director of the Federal Bureau of Investigation, reasonably believes to be an entity owned or controlled by, or otherwise connected to, the government of a covered foreign country.
Critical technology means—
(1) Defense articles or defense services included on the United States Munitions List set forth in the International Traffic in Arms Regulations under subchapter M of chapter I of title 22, Code of Federal Regulations;
(2) Items included on the Commerce Control List set forth in Supplement No. 1 to part 774 of the Export Administration Regulations under subchapter C of chapter VII of title 15, Code of Federal Regulations, and controlled—
(i) Pursuant to multilateral regimes, including for reasons relating to national security, chemical and biological weapons proliferation, nuclear nonproliferation, or missile technology; or
(ii) For reasons relating to regional stability or surreptitious listening;
(3) Specially designed and prepared nuclear equipment, parts and components, materials, software, and technology covered by part 810 of title 10, Code of Federal Regulations (relating to assistance to foreign atomic energy activities);
(4) Nuclear facilities, equipment, and material covered by part 110 of title 10, Code of Federal Regulations (relating to export and import of nuclear equipment and material);
(5) Select agents and toxins covered by part 331 of title 7,…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .