VAMC_Manhattan___Kitchen_Equipment_CutsheetBook with high light.pdf

STAINLESS STEEL

REGALINE SINKS

One Compartment - Two Drainboards

Item #: Qty #:

Model #:

Project #:

www.advancetabco.com

Customer Service Available To Assist You 1-800-645-3166 8:30 am - 7:00 pm E.S.T.

For Orders & Customer Service:

Email: customer@advancetabco.com or Fax: 631-242-6900

For Smart Fabrication™ Quotes:

Email: smartfab@advancetabco.com or Fax: 631-586-2933

REF-C

93 & 9 SERIES

Adjustable Side Cross-Bracing

94 SERIES

Adjustable Side &

Front Cross-Bracing

Bowl Size O.A.

Length

DRBD.

Size

SPEC-LINE 94 Series STANDARD 93 Series SUPER SAVER 9 Series Cu.

Ft.Model # WT. Model # WT. Model # WT.

14 Ga. 304 S/S 14” Water Level

16 Ga. 304 S/S 12” Water Level

18 Ga. 304 S/S 12” Water Level

16” x 20” 54” 18” 94-1-24-18RL 97 lbs. 93-1-24-18RL 82 lbs. 9-1-24-18RL 71 lbs. 29

66” 24” 94-1-24-24RL 118 lbs. 93-1-24-24RL 95 lbs. 9-1-24-24RL 95 lbs. 33

90” 36”* 94-1-24-36RL 164 lbs. 93-1-24-36RL 134 lbs. 9-1-24-36RL 134 lbs. 48

20” x 20” 58” 18” 94-21-20-18RL 95 lbs. 93-21-20-18RL 78 lbs. 9-21-20-18RL 78 lbs. 26

70” 24” 94-21-20-24RL 117 lbs. 93-21-20-24RL 92 lbs. 9-21-20-24RL 92 lbs. 34

94” 36”* 94-21-20-36RL 168 lbs. 93-21-20-36RL 147 lbs. 9-21-20-36RL 147 lbs. 50

18” x 24” 56” 18” 94-61-18-18RL 160 lbs. 93-61-18-18RL 138 lbs. 9-61-18-18RL 138 lbs. 29

68” 24” 94-61-18-24RL 179 lbs. 93-61-18-24RL 150 lbs. 9-61-18-24RL 150 lbs. 43

92” 36”* 94-61-18-36RL 210 lbs. 93-61-18-36RL 180 lbs. 9-61-18-36RL 180 lbs. 67

24” x 24” 74” 24” 94-41-24-24RL 213 lbs. 93-41-24-24RL 185 lbs. 9-41-24-24RL 185 lbs. 48

98” 36”* 94-41-24-36RL 252 lbs. 93-41-24-36RL 210 lbs. 9-41-24-36RL 210 lbs. 64

20” x 28” 58” 18” 94-81-20-18RL 173 lbs. 93-81-20-18RL 150 lbs. 9-81-20-18RL 150 lbs. 46

70” 24” 94-81-20-24RL 186 lbs. 93-81-20-24RL 165 lbs. 9-81-20-24RL 165 lbs. 55

94” 36”* 94-81-20-36RL 225 lbs. 93-81-20-36RL 195 lbs. 9-81-20-36RL 195 lbs. 73

14” Water Level 18” Flood Level

12” Water Level 16” Flood Level

12” Water Level 16” Flood Level

* Regalines with 36” Drainboards are Supplied with Two Additional Legs (per drainboard) for Support.

Weights & Cubes Are Approximate

FEATURES:

Tile edge for ease of installation.

One piece Deep Drawn sink bowls with integral drainboards with splash.

Featuring the single bowl unit design.

All sink bowls have a large liberal 3” radius.

“94” Series is supplied with adjustable front and side cross braces featuring leg clamps.

“93” & “9” Series is supplied with adjustable side cross braces featuring leg clamps.

CONSTRUCTION:

All TIG welded.

Welded areas blended to match adjacent surfaces and to a satin finish.

MATERIALS:

Spec-Line (94 Series): 14 gauge type 304 stainless steel

11” High Splash.

Standard (93 Series): 16 gauge type 304 stainless steel 8” High Splash.

Super Saver (9 Series): 18 gauge type 304 stainless steel 8” High Splash.

LEGS: • 1 5/8” diameter tubular stainless steel.

• Stainless steel gussets.

• Stainless Steel 1” adjustable bullet feet.

YES! It's SeaM ess!

Recessed Bowl Surface Accommodates Poly-Vance

Cutting Boards & Sink Covers

93 & 9 Series Adjustable Side Cross-Bracing

94 Series Adjustable Side & Front Cross-Bracing

Advance Tabco 9‐21‐20‐18RL Item #1 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 1

VHABYNChowS Highlight

VHABYNChowS Underline

VHABYNChowS Highlight

325 Wireless Boulevard, Hauppauge, NY 11788

DIMENSIONS and SPECIFICATIONS

MECHANICAL:

• Supply is 1/2” IPS hot & cold.

• Faucet holes on 8” centers.

• Faucets are not included (see accessories).

• Waste drains are 1 1/2” IPS S/S basket type, located in center of sink bowl, and are included.

TOL Overall: ± .500” ALL DIMENSIONS ARE TYPICAL Interior: ± .250”

* Regalines with 36” Drainboards are Supplied with Two Sets of Legs for Support.

REF-C

ADVANCE TABCO is constantly engaged in a program of improving our products. Therefore, we reserve the right to change specifications without prior notice.

© ADVANCE TABCO, OCTOBER 2021

DESCRIPTION 94 SERIES 9 & 93 SERIES

BOWL

SIZE

Overall

Length

DRBD

SIZE

Recommended

Use A B C D V W X Y Z V W X Y Z

16”x20”

54” 66” 90”

18” 24”

*36”

DISH

SINKS

20” 16” 14 1/8” 28” 38” 11” 14” 19” 45” 38” 8” 12” 21” 42”

20”x20”

58” 70” 94”

18” 24”

*36”

DISH &

POT SINKS

20” 20” 14 1/8” 28” 38” 11” 14” 19” 45” 38” 8” 12” 21” 42”

18”x24”

56” 68” 92”

18” 24”

*36”

POT & PAN

SINKS

24” 18” 16 1/8” 32” 38” 11” 14” 19” 45” 38” 8” 12” 21” 42”

24”x24” 74” 98”

24” *36”

POT SINKS 24” 24” 16 1/8” 32” 38” 11” 14” 19” 45” 38” 8” 12” 21” 42”

20”x28”

58” 70” 94”

18” 24”

*36”

PAN SINKS 28” 20” 18 1/8” 36” 38” 11” 14” 19” 45” 38” 8” 12” 21” 42”

Finished Floor

Flood Level

X + 4"

37" Top Of

Rolled Rim

"X" Bowl

Depth

1"

34" Top Of

Drainboard

W

1" Adj S/S Bullet Feet

Wall

Z

4"

SECTION

3"

1"

Drain V

112" 2"

C

Y P-Trap

To Waste Line

Finished Floor

LC

LC

PLUMBING ROUGH-IN

Overall Length

D

B

A

Drainboard Size

Advance Tabco 9‐21‐20‐18RL Item #1 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 2

FAUCET AERATOR CONFORM TO

ASTM.A112.18.1M • 1.5 GPM/5.7 LPM

THREAD: 55/64 - 27 FEMALE

K-101

8” SWING SPOUT SPLASH MOUNT FAUCET

Conforms To NSF 61/9 Lead Free Requirements

REF-G

www.advancetabco.com

Customer Service Available To Assist You 1-800-645-3166 8:30 am - 7:00 pm E.S.T.

For Orders & Customer Service:

Email: customer@advancetabco.com or Fax: 631-242-6900

For Smart Fabrication™ Quotes:

Email: smartfab@advancetabco.com or Fax: 631-586-2933

ADVANCE TABCO is constantly engaged in a program of improving our products. Therefore, we reserve the right to change specifications without prior notice. © ADVANCE TABCO, NOV. 2021

FEATURES:

8” swing spout.

8” O.C. water supply.

Quarter-turn wedge style handles.

Colored hot & cold Indexes.

1.5 GPM/5.7 LPM Aerator. 60 PSI.

MATERIAL:

Brass chrome plated body & spout.

Chrome plated handles.

DIMENSIONS and

SPECIFICATIONS

Item #: Qty #:

Model #:

Project #:

A Length

B Height C D

On Center Dimensions

8” 4 1/4” 2 1/4” 10” 8” O.C.

B

C

D A

CL

CL

Click This Link To View Assembly Sheet

Faucet(s) on this page may expose you to chemicals, including lead, that are known to the State of California to cause cancer or birth defects or other reproductive harm. For more Info.,visit www.p65warnings.ca.gov.

WARNING:

BACK VIEW

1/2” NPT(INSIDE THREAD)

Options & Accessories

Splash Mount Faucet Mounting Kit K-06

Wrist Handles* K-316-LU (Set of 2)

*Can Only Be Used On Faucets Purchased After January 2016.

For Older Faucets, Consult Customer Service.

Low Flow Aerator

K-08

.5 GPM

Replacement Spout For K-101 Faucet

K-101SP

8” Swing Spout Only.

For a Complete faucet with Wrist Handles, See our K-316 Spec Sheet.

Faucet Repair Kit* K-00B (Set of 2) Includes 2 Cartirdges and 2 Handles With Red & Blue Indexes

Advance Tabco K‐101 Item #1 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 3

DISHTABLE MODSDishtable Modifications & Accessories

DTA-95

DTA-87

DTA-82

DTA-45

K-475

K-454

K-452

DTA-84

K-460

DTA-81

REF-Q

K-23 Welded Set-Up/Crated

K-24 Shell Crating

K-37 Anti-Siphon Vacuum Breaker Hole

K-57 Welded Field Joint (Welded In Field By Others)

K-76 Paint On Sound Deadening

K-77 Splash Cut-Out (Pipe Chase)

K-440 Waste Trough Installation Welded Into Table And Furnished With A 2” Deep Removable Basket

K-452 Control Bracket 8” x 12”

K-453 Control Bracket 14” x 16”

K-454 Side Splash

K-456 Scrap Block Installed (Includes Rubber Scrap Block)

K-460 Disposal Cone Welded Into Table And Furnished With 8” x 12” Control Bracket & Faucet Holes (Supplied By Others)

K-460A Installation Of Disposal Cone With 14” x 16” Control Bracket, Faucet Holes (Cone Supplied By Others)

K-461 Disposal Collar Welded Into Sink Bowl And Furnished With 8” x 12” Control Bracket (Supplied By Others)

K-461A Disposal Collar Welded Into Sink Bowl And Furnished With 14” x 16” Control Bracket (Supplied By Others)

K-472 Special Faucet Hole Location

K-495 Turn Down Backsplash (Incl. 2 Brackets. See K-397 For Addt’l Sets)

K-508A Special Modification Charge

K-550 Stainless Steel Tubular Rack Storage

DTA-40 Drain Hole (For Sorting Table)

K-4 Lever Drain Bracket

K-5 Twist Handle Operated Drain

K-15 Twist Handle Operated Drain With Overflow

K-397 Wall Brackets (2 Each. Brackets Included With K-495)

K-455C Stainless Steel Sink Cover 16” x 20”

K-455E Stainless Steel Sink Cover 20” x 20”

K-457 Replacement Rubber Scrap Block (See K-456 For Install Cost)

K-475 Replacement S/S Leg With Stainless Steel Bullet Foot

K-478 Replacement Stainless Steel Bullet Foot

K-488 Flanged S/S Bullet Foot

K-550 Stainless Steel Tubular Rack Storage

K-610 Perforated Stainless Steel Sink Grid (Specify Bowl Size)

K-700D 12” High Removable Side Splash For Dishtables (Specify Model)

DTA-53 SPEC-LINE Heavy Duty Prerinse Faucet

DTA-51 Pre-Rinse Slide Bar for 18” x 24” Fab. Sink Bowls

DTA-45

Scrap Trough Welded To Dump Sink - Min. Scrap Trough Length Is 3’. Max. Length Is 8’. For 20” x 20” x 8” Bowl Spec-Line Soil S30 Series Only. - Consult Factory For Trough Lengths Exceeding 8 Feet

DTA-46 Inside Mitered Corner

DTA-66 Provision For Dishlanding On Straight Soil Table (Min 4’)

DTA-70 Install Booster Heater Brackets (Brackets By Others)

DTA-72 Provision For Side Loader

DTA-75 Provision For Limit Switch (Limit Switch By Others)

DTA-76 Move Prerinse Sink To Conform To Dishmachine Requirements. Please Specify Machine When Placing Order

DTA-78 Notch In Backsplash Return To Clear Handle Please Specify Machine When Placing Order

DTA-81 S/S Welded Leg Assembly with S/S Feet

DTA-82 15” x 20” x 8” Undercounter Dump Sink

DTA-84 Simple Pass-Thru (Specify Wall Thickness - Min. Length 36”)

DTA-87 Pass-Thru Wall Frame (Specify Wall Thickness - Min. Length 36”)

DTA-95 Install Scrapper Top

DTA-96 Install Trough Collector

DTA-99A 16” x 20” x 12” Sink Bowls

DTA-99B 20” x 20” x 12” Sink Bowls

DTA-99C 10” x 14” x 5” Dump Sink

DTA-99D 18” x 24” x 14” Sink

DTA-99E 24” x 24” x 14” Sink

DTA-106 Mirror Highlight To Dishtable Upgrade

MODIFICATIONS

ACCESSORIES

DTA-52 Pre-Rinse Slide Bar for 24” x 24” Fab. Sink Bowls

DTA-55 Column Notch (Includes Splash)

DTA-56 Addt’l Length On 59” Side Of Corner Or Straight Tables

DTA-58 Pre-Rinse Basket w/ Slide Bar for 18” x 24” Fab. Sink Bowls

DTA-59 Pre-Rinse Basket w/ Slide Bar for 24” x 24” Fab. Sink Bowls

DTA-60 Prerinse Slide Bar for 20” x 20” Fab. Sink Bowls

DTA-62 Prerinse Basket For 20” x 20” Deep Drawn Bowls

DTA-63 Prerinse Slide Bar For 20” x 20” Deep Drawn Bowls

DTA-64 Prerinse Slide Bar For 16” x 20” Fab. Sink Bowls

DTA-65 Prerinse Slide Bar For 16” x 20” Deep Drawn Bowls

DTA-67 Stainless Steel Rear Cross-Bracing (Factory Installed Only)

DTA-69 Prerinse Basket For 16” x 20” Deep Drawn Bowls

DTA-100 Prerinse Basket with Slide Bar for 20” x 20” Fab. Sink Bowls

DTA-125 Prerinse Basket with Slide Bar for 16” x 20” Fab. Sink Bowls

DTA-125A Perforated Basket for DTA-82 Dump Sink

Advance Tabco K‐5 Item #1 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 4 www.advancetabco.com

Customer Service Available To Assist You 1-800-645-3166 8:30 am - 8:00 pm E.S.T.

For Orders & Customer Service:

Email: customer@advancetabco.com or Fax: 631-242-6900

For Smart Fabrication™ Quotes:

Email: smartfab@advancetabco.com or Fax: 631-586-2933

ADDITIONAL DISHTABLE

ACCESSORIES

For More Faucet Options & Faucet Specs, See Faucet Specifications

REF-Q

NEW YORK GEORGIA TEXAS NEVADA

Fax: (631) 242-6900 Fax: (770) 775-5625 Fax: (972) 932-4795 Fax: (775) 972-1578www.advancetabco.com

Customer Service Available To Assist You 1-800-645-3166 8:30 am - 8:00 pm E.S.T.

Email Orders To: customer@advancetabco.com. For Smart Fabrication™ Quotes, Email To: smartfab@advancetabco.com or Fax To: 631-586-2933

Lever Operated Drain

K-5

Lever Drain Support Bracket

K-4

INDIVIDUAL

Stainless Steel Legs with Stainless Steel

Adjustable Bullet Feet

K-475

Splash Mounted Faucet

EXTRA HEAVY DUTY

K-119 8” O.C.

16” Spout

Add-A-Faucet for DTA-53 Prerinse Faucet K-117

Add-A-Faucet for K-116 Prerinse Faucet

K-117-TS

Splash Mounted Faucet

K-101 8” O.C.

8” Spout

K-116 8”O.C.

Wall Bracket Included

Splash Mtd.

Prerinse Faucet

Twist Handle 2” IPS

Stainless Steel Sink Compartment Covers

K-455 16” x 20” Cover or 20” x 20” Specify Size

Interchangeable with T&S Brand Faucets

T&S Equivalent = B133-B

SPEC-LINE

EXTRA HEAVY DUTY

DTA-53

8”O.C.

Wall Bracket Included

Splash Mounted

Prerinse Faucet

ADVANCE TABCO is constantly engaged in a program of improving our products. Therefore, we reserve the right to change specifications without prior notice. © ADVANCE TABCO, OCT 2018

Prerinse Baskets with Welded Slide Bar For Fabricated Bowls

Prerinse Baskets with Welded Slide Bar For Deep Drawn Bowls

Prerinse Slide Bars For Fabricated Bowls Prerinse Slide Bars for Deep Drawn Bowls

Model # Fits Bowls Wt. Cu.

DTA-64 16” x 20” 7 lbs. 1 DTA-60 20” x 20” 9 lbs. 1

Large Size Prerinse Slide Bars DTA-51 18” x 24” 8 lbs. 1

DTA-52 24” x 24” 10 lbs. 1

Model # Fits Bowls Wt. Cu.

DTA-65 16” x 20” 7 lbs. 1 DTA-63 20” x 20” 9 lbs. 1

Model # Fits Bowls Wt. Cu.

DTA-125 16” x 20” x 4” 9 lbs. 1

DTA-100 20” x 20” x 4” 12 lbs. 1

Large Size Baskets

DTA-58 18” x 24” x 4” 11 lbs. 1

DTA-59 24” x 24” x 4” 20 lbs. 1

Model # Fits Bowls Wt. Cu.

DTA-69 16” x 20” x 4” 9 lbs. 1

DTA-62 20” x 20” x 4” 12 lbs. 1

DTA-100

Shown

DTA-62

Shown

Faucet(s) on this page may expose you to chemicals, including lead, that are known to the State of California to cause cancer or birth defects or other reproductive harm. For more Info.,visit www.p65warnings.ca.gov.

WARNING:

Advance Tabco K‐5 Item #1 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 5

S T E A M

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602 a division of ITW Food Equipment Group LLC

F37450 (12/20)

Item # C.S.I. Section 11420

KE SERIES

ELECTRIC COUNTER TILTING KETTLE

STANDARD FEATURES

■ 2⁄3 jacketed self-contained electric counter tilting steam kettle.

■ Ellipsoidal bottom kettle liner formed and fully welded type 316 and type 304 stainless steel exterior with 1⁄4 x 5⁄8 inch bar rim with butterfly shaped pouring lip and embossed gallon/liter markings, designed to operate at a maximum of 50 psi (3.4 kg/cm2).

■ Jacket contains water, rust inhibitor and antifreeze mixed to protect to 30° below zero.

■ Removable electric elements are field serviceable.

■ Stainless steel tilt handle can be mounted on either the right or left. Two position tilt lock, upright, 100° for emptying and cleaning.

■ Stainless steel water tight control housing located on the right. Controls include a power switch, indicator light, solid state temperature control, vacuum/pressure gauge, pressure relief valve, low water light and low water shut-off.

■ Faucet bracket.

■ Mounting base includes lugs for bolting to counter top or floor stand.

■ Shipped for 208/60-50/3 electrical service. Can be field converted to 208/60-50/1 and 240/60-50/3 and 240/60-50/1.

■ One year limited parts and labor warranty.

OPTIONS

■ Security facility package.

a. Security type tamper resistant fasteners with tack welds.

ACCESSORIES (Packaged & Sold Separately)

with backflow preventer.

SPECIFICATIONS

(6) (12) gallon capacity, 2⁄3 jacketed self-contained electric counter tilting kettle. Ellipsoidal bottom kettle liner formed and fully welded type 316 and type 304 stainless steel exterior with 1⁄4 x 5⁄8 inch bar rim with butterfly shaped pouring lip and embossed gallon/liter markings, designed to operate at a maximum of 50 psi (3.4 kg/cm2). Jacket contains water, rust inhibitor and antifreeze mixed to protect to 30° below zero.

Removable electric elements are field serviceable. Stainless steel tilt handle can be mounted on either the right or left.

Two position tilt lock, upright, 100° for emptying and cleaning.

Stainless steel water tight control housing located on the right.

Controls include a power switch, indicator light, solid state temperature control, vacuum/pressure gauge, pressure relief valve, low water light and low water shut-off. Mounting base includes lugs for bolting to counter top or floor stand. Shipped for 208/60-50/3 electrical service. Can be field converted to 208/60-50/1 and 240/60-50/3 and 240/60-50/1.

Exterior Dimensions:

K6ETT: 213⁄4"w x 151⁄2"d x 33"h.

K12ETT: 251⁄2"w x 191⁄2"d x 381⁄2"h.

UL listed. UL Classified for sanitation in accordance with ANSI/NSF Standard #4. Meets ASME code.

Model K12ETT shown with accessory stand

Vulcan K12ETT Item #2 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 6 http://vulcanequipment.com/ http://vulcanequipment.com/Products/2-3-Jacketed-Manual-(Hand)-Tilting-Counter-Kettles/

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

F37450 (12/20)

KE SERIES

ELECTRIC COUNTER TILTING KETTLE

NOTE: In line with its policy to continually improve its products, Vulcan reserves the right to change materials and specifications without notice.

NOTE:

• Plastic drains are not recommended due to limited temperatures of the plastic.

• This appliance is manufactured for commercial installation only and is not intended for home use.

MODEL CAPACITY A B C D E F G H J K M

K6ETT

6 gallons inches 11.8 14.36 24.88 33.04 15.05 23.33 8.7 27 4 4 6.66 23 liters mm 300 365 632 839 382 593 221 686 102 102 169

K12ETT

12 gallons inches 17.80 13.6 24.37 38.53 20.68 29.34 5.8 27 6 4 6.2 45 liters mm 452 345 619 979 525 745 147 686 152 102 156

ELECTRICAL CHARACTERISTICS

MODEL KW

208V 230V 240V 480V

1 PH 3 PH 1 PH 3 PH 1 PH 3 PH 3 PH

K6ETT

7.5 36 22 N/A N/A N/A N/A 9 10 N/A N/A 40 23 42 26 N/A

K12ETT

12 58 33 N/A N/A N/A N/A 14 16 N/A N/A 64 37 67 39 N/A

2.250 (57,15)14.500

(368,3)

19.000 (482,6)

D

M

B

C

A ID

19.000 (482,6)

1.250 (31,75)

14.500 (368,3)

10.000

(254) 12.500

(317,5)

2.250 (57,15)

10.000 (254)

12.500 (317,5)

H

1.250 (31,75)

J

G K

ELEC CONNECTION

F

E

4.420 (112,27)

ELEC CONNECTION

• Dimensions which locate the connections have a tolerance of + or -3" (+ or -75 mm).

• Installation of backflow preventers, vacuum breakers and other specific code requirements is the responsibility of the owner and installer. It is the responsibility of the owner and installer to comply with local codes.

Vulcan K12ETT Item #2 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 7

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

F-32474 (04/10)

Item # C.S.I. Section 11420

VSKT30

STAND FOR COUNTER

BRAISING PANS & KETTLES

Model VSKT30

VSKT30 29.5" wide, stand for K6ETT & K12ETT self-contained kettles & VECTS12 & VECTS16 electric braising pans

STANDARD FEATURES

Stainless steel frame, utility tabs, drain basin, stationary ■ gutter and flanged feet on front and rear.

Drain basin slides on stainless steel roller and ball ■ bearings.

Integral splash shield/cover provides a work surface when ■ closed and splash containment when raised.

Complete with mounting hardware for Vulcan counter ■ braising pans and kettles.

One year limited parts and labor warranty. ■

OPTIONS

Direct kettle adapter for K6TTD and K12TTD direct steam kettles.

SPECIFICATIONS

Counter steam equipment stand, Vulcan-Hart Model VSKT30.

Stainless steel frame, utility tabs, drain basin, stationary gutter and flanged feet on the front and rear. Drain basin slides on stainless steel roller and ball bearings. Integral splash shield/ cover provides a work surface when closed and splash containment when raised. Complete with mounting hardware for Vulcan counter braising pans and kettles.

Exterior Dimensions:

29.5"w x 24"d x 18"h mounting height. (28.5"h with splash shield raised)

NSF listed.

Vulcan STAND VSKT30 Item #2 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 8

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

F-32474 (04/10)

VSKT30

STAND FOR COUNTER

BRAISING PANS & KETTLES

NOTE: In line with its policy to continually improve its products, Vulcan reserves the right to change materials and specifications without notice.

FRONT VIEW

TOP VIEW

SIDE VIEW

DRAIN BASIN - CLOSED

SIDE VIEW

DRAIN BASIN - OPEN

Vulcan STAND VSKT30 Item #2 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 9

C O M B I

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

F47104 (04/18)

Item # C.S.I. Section 11420

ABC SERIES

GAS BOILERLESS COMBI OVEN STEAMER

Model ABC7G (shown on stand)

ABC7G-NAT ABC7G-PRO

ABC7G-NATP ABC7G-PROP

STANDARD FEATURES

■ Engineered and assembled in Louisville, Kentucky, USA.

■ Just three knobs, no modes, only temperature, time and humidity.

■ Patent-pending humidity level control automatically adjusts after setting temperature.

■ Multiple cooking capabilities from one piece of equipment:

Baking, Steaming, Roasting, Air-Fry, Rethermalization, Proofing, Finishing, Poaching, Stewing, Low Temp and Defrosting results.

■ Boilerless combi uses direct steam creation optimizing cooking capability & production with minimal energy & water.

■ Auto-reversing fan with electronic braking system on fan motor.

■ Large LED displays for temperature, time and humidity controls.

- Temperature range: 80-450°F

- Timer range: continuous (--:--) up to 23:59 hours and minutes

- Humidity range: 0-100%

■ Visual recall display of actual temperature and humidity LED’s.

■ Timer reloads for batch cooking after completion of timed cycle.

■ Flashing door light & audible alarm system alert user when cook-ing cycle finished.

■ Halogen door light behind heat reflective inner glass.

■ (4) stainless steel Grab-n-Go Racks with 151⁄2" x 31⁄4" cutout design for easy access to pans.

■ Machine diagnostics accessed thru controls or via USB.

■ Cool to the touch & energy efficient heat reflective tempered glass door.

■ All stainless steel cavity, top, sides & fully insulated.

■ One year limited parts and labor warranty (two year K-12).

■ ABC-P models include food probe and fan speed control.

OPTIONS

Hollow Carbon Filter System - Good (Suggested Minimum):

- CB15K-SYSTEM – 15,000 gal. (carbon only treatment)

- CB30K-SYSTEM – 30,000 gal. (carbon only treatment)

Water Softening - Better (Carbon CBK System Required)

- WS-40 - 40 lb. capacity (hard water treatment)

Reverse Osmosis System – Best

- V3MRO-1 up to 100 gpd capacity, single unit

- V3MRO-2 up to 200 gpd capacity, double unit

Second year extended limited parts and labor warranty contract.

ACCESSORIES (Packaged & Sold Separately)

GASKIT-ABC – Propane & altitude kit (2,000-10,000 ft.)

ADDRACK-ABC1 – (1) One additional Grab-N-Go Rack ADDRACK-ABC3 – (3) Three additional Grab-N-Go Racks 1220-BASKET – Fry Basket 12" x 20" Stands & Stacking Kits include: (1) Spray Hose and Drip Tray Kit

- STACK-ABC/G – Gas stacking kit for two ABC7G combis.

- STACK-ABC/CONV – Stack kit for combi/convection.

- STAND-ABC/SS – Stainless steel open frame stand.

- ABC-BASE – Stainless steel base for STAND-ABC/SS.

HOSEWTR-3/4BBV - s/s flex water hose 72" length, ¾" female NSHT (2 per unit recommended).

SPECIFICATIONS

Vulcan Combi Oven, Gas, Boilerless, 7 level full size combi, Model ABC or ABC-P. Engineered and assembled in USA. Just three knobs, no modes, only temperature, time and humidity for ultimate ease of use. Humidity level control automatically adjusts after setting tem-perature. Multiple cooking capabilities from one piece of equipment:

Baking, Steaming, Roasting, Air-Fry, Rethermalization, Proofing, Fin-ishing, Poaching, Stewing, Low Temp and Defrosting results. Direct steam creation for optimized cooking capability and production with minimal energy and water consumption. Auto-reversing fan with elec-trical braking system on fan motor. Large LED displays for temperature, time and humidity controls. Visual recall display of actual temperature and humidity LED’s. Timer reloads for batch cooking after completion of timed cycle. Flashing door light & audible alarm system alert user when cooking cycle finished. Halogen door light behind heat reflec-tive inner glass. (4) stainless steel Grab-N-Go Racks with 151⁄2" x 31⁄4" cutout design for easy access to pans. Maximum capacity of (7) racks for a total of (7) 18" x 26" or (14) 12" x 20" pans. Machine diagnostics accessed thru controls or via USB. Cool to the touch & energy efficient heat reflective tempered glass door. All stainless steel interior cooking compartment, top, sides & fully insulated. One year limited parts and labor warranty.

Exterior Dimensions:

Combi: 35"H x 42.2"W x 43.5"D Stand & Combi: 63.1"H x 42.2"W x 43.5"D Stacked Combi: 75.2"H x 42.2"W x 43.5"D

ANS Z83.11 / CSA 1.8

NSF/ANSI 4

ABC ABC-P

Vulcan ABC7G‐NAT Item #3 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 10 http://vulcanequipment.com/ http://www.vulcanequipment.com/products/gas-boilerless-commercial-combi-oven-steamer/

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

C O M B I

F47104 (04/18)

ABC SERIES

GAS BOILERLESS COMBI OVEN STEAMER

NOTE: In line with its policy to continually improve its products, Vulcan reserves the right to change materials and specifications without notice.

WATER QUALITY STATEMENT:

The fact that a water supply is potable is no guarantee that it is suitable for steam generation. All steam equipment is subject to contamination and failure due to chemical and mineral content found in water. A suitable Hobart Water Treatment System and regular filter replacements coupled with routine deliming is the recommended minimum. Damage as a result of poor water quality or lack of required owner/operator maintenance is the responsibility of the owner/operator.

Your water supply must be within these general guidelines:

DYNAMIC WATER PRESSURE 30 - 60 psig HARDNESS* 1 - 3 grains SILICA less than 13 ppm TOTAL CHLORIDE less than 30 ppm pH RANGE 7-8 CHLORINE & CHLORAMINE 0 ppm ALKALINITY less than 20 ppm TDS less than 60 ppm UN-DISSOLVED SOLIDS less than 5 microns

* 17.1 ppm = 1 grain of hardness

Other factors affecting steam generation are iron content, amount of chlorination and dissolved gases. Water supplies vary from state to state and from locations within a state. Therefore it is necessary that the local water treatment specialist be consulted before the installation of any steam generating equipment.

USER RESPONSIBILITY:

The product must be installed, cleaned and maintained as described in the Manual furnished with the product. It is the responsibility of the owner and installer to comply with local codes.

SERVICE CONNECTIONS:

Water: 3⁄4" NSHT female split water line connections (filtered and unfiltered).

Drain: 1" NPT male connection piped to open drain, 60" maximum length before open air gap and not more than two bends or elbows.

Electrical: 120 Volt, 15 Amp,NEMA 5-15P plug and cord.

Gas: 80,000 BTU, 3⁄4" NPT female connection. Supply gas pressure should be: Natural gas 5" - 10.5" W.C.; Propane gas 11" - 13" W.C.

NOTE:

Clearance: Left 1", Back 4", Right 3" required, 18" recommended for service access on right side.

The spark ignition in this appliance can cause electrical noise that can false trigger the GFCI detection. Some GFCI’s are more sensitive than others. The use of a higher trip tolerance GFCI will reduce nuisance tripping. Contact Technical Support for more information.

MACHINE WEIGHT: 600 lbs.

Vulcan ABC7G‐NAT Item #3 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 11

Item # _____________________________________

Quantity ___________________________________

C.S.I. Section 11400

F40286 – Water Treatment Systems Steamer/Combi (Flash Type) Applications Page 1 of 2

WATER TREATMENT SYSTEMS

STEAMER/COMBI (FLASH TYPE)

APPLICATIONS701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com

W A

T E

R T

R E

A T

M E

N T

S Y

S T

E M

S S

T E

A M

E R

/C O

M B

I (FLA

S

H T

Y P

E ) A

P P

LIC

A

T

IO

N S

STANDARD FEATURES

■ Single cartridge hollow carbon filter system includes mounting bracket, 3⁄4" NPTF inlet and outlet, shut-off valve, test port, and gauge.

■ Reduce Chloramine, Chlorine, Sediment, Bad Tastes and Odors, Total Organic Compounds, Tannins and Trihalomethanes

■ Modular design is adaptable to accommodate changing water conditions

■ Simple to install and service

■ FOR COLD WATER USE ONLY

Min./Max. Pressure: 40 – 125 psi Min./Max. Temperature: 40º – 100º F

– CB15K-SYSTEM (00-847487-00001)

Rated Capacity (Gallons)*: 15,000 Flow Rate: 3.7 gpm Shipping Weight: 18 Lbs.

– CB30K-SYSTEM (00-847487-00002)

Rated Capacity (Gallons)*: 30,000 Flow Rate: 5 gpm Shipping Weight: 20 Lbs.

■ Quick-Change cartridge design for replacement without tools

■ Replacement Cartridge Filters:

CB15K-PMKIT - 15,000 Gallon Rated Capacity

(00-847487-1PMK)

CB30K-PMKIT - 30,000 Gallon Rated Capacity

(00-847487-2PMK)

■ Exterior dimensions:

CB15K-SYSTEM 14" w x 9" d x 237⁄8

CB30K-SYSTEM 14" w x 9" d x 287⁄8

MODELS

❑ CB15K-SYSTEM

❑ CB30K-SYSTEM

Specifications, Details and Dimensions on Reverse Side.

* Independently tested by an E.P.A. approved laboratory to ANSI/NSF Standard 42 & 53 specifications for the reduction of Cyst, Particulate Class I, Chlorine, Chloramine, Taste and Odor.

Vulcan CB30K‐SYSTEM Item #3 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 12

701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com

Page 2 of 2 F40286 – Water Treatment Systems Steamer/Combi (Flash Type) Applications

As continued product improvement is a policy of Hobart, specifications are subject to change without notice.

WATER TREATMENT SYSTEMS

STEAMER/COMBI (FLASH TYPE)

APPLICATIONS

F40286 (REV. 02/14) LITHO IN U.S.A. (H-01)

NOTICE:

• Failure to replace cartridge before end of capacity life can result in pitting, rusting and discoloration due to Chloramines and Chlorine in water supply.

• Routine filter replacement & deliming are required for warranty consideration.

• This filter does not remove scale build-up due to hardness or other contaminants that may be in water.

• Hardness will result in scale build-up. Deliming is required to remove scale build-up or use of an additional treatment such as a water softener is recom-mended.

• Gallon capacity will vary according to flow rate, inlet pressure and local water conditions.

• Replace cartridge if outlet pressure gauge is less than 20 psi. or before end of capacity life (Maximum car-tridge operating life 1 year.)

Water Quality Statement The fact that a water supply is potable is no guarantee that it is suitable for steam generation. Systems are not to be used where water is microbiologically unsafe or with water of unknown quality without adequate disinfections before and after use. Other factors affecting steam generation include iron content, amount & type of chlorination, and dissolved gasses. Water supplies vary from state to state and from locations within a state.

As with all steam related products, water filtration and regular filter replacements coupled with routine Deliming are required. Your local Hobart office can recommend a water treatment or filtration system to meet the needs of your local water conditions. Contact your local Hobart representative for water treatment offerings.

Note:

• Installation of backflow preventers, vacuum breakers and other specific code requirements is the responsibil-ity of the owner and installer in compliance with local codes.

Recommended filter clearance needed for access:

Front 13" Bottom 4"

This appliance is manufactured for commercial installation only and not intended for home use.

EXTERIOR DIMENSIONS:

MODEL WIDTH DEPTH HEIGHT

CB15K-SYSTEM 14" 9" 237⁄8

CB30K-SYSTEM 14" 9" 287⁄8

.6

(R4)

.2

.7

(2 3.

( 14 ) w/ ball valve and connecting fittings when used

.6

(R4)

.2

.7

(2 9)

( 14 ) w/ ball valve and connecting fittings when used

CB15K CB30K

Vulcan CB30K‐SYSTEM Item #3 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 13

The Dormont Blue Hose®

Stainless Steel Construction Stainless Steel Braid Blue PVC Coating

(Cutaway shown)

Features SnapFast® One-Handed Quick-Disconnect Quick-Disconnect ........................ Brass body, aluminum collar Thermal Shut-off .......................... Shuts off gas when internal temperatures exceed 350°F (177ºC) Additional Components Restraining Device ....................... PVC coated, steel multi-strand cable and mount-ing hardware Valve ...........................................Full port, brass body Elbow ..........................................Malleable iron *Deluxe Kits Include ..................... The Dormont Blue Hose, valve, restraining device, elbows, SnapFast, display box

Specifications The Dormont Blue Hose®

Tubing .........................................Annealed, 304 stainless steel Braiding .......................................Multi-strand, stainless steel wire Coating ........................................ Blue antimicrobial PVC, melts at 350ºF (177ºC);

coating will not hold a flame End Fittings ..................................Carbon steel; zinc trivalent chromate Stress Guard® ..............................360º rotational end fitting at both ends

Stress Guard®

Rotation Technology Reduces Stress at Both Ends of the Hose

SnapFast® One-handed Quick-Disconnect

SnapFast® Quick-Disconnect Assemblies Sizes: ½" to 1¼" SnapFast Quick-Disconnect Assemblies feature flexible movement and the one-handed quick-disconnect fitting with a unique thermal shut-off design that automatically shuts off the gas when the internal temperature exceeds 350°F (177°C).

The Dormont Safety System™ is the first and only complete gas equipment connection system specifically engineered for the commercial kitchen. The Safety System consists of the famous Dormont Blue Hose and a variety of accessories designed for improved safety and performance in commercial kitchens. Because they are manufactured in the USA under an ISO qualified production process and to multiple design certifications, you can Connect with Confidence with the Dormont Safety System.

Stress Guard®

Rotation Technology Reduces Stress at Both Ends of the Hose

Job Name ________________________________________ Job Location ______________________________________ Engineer _________________________________________ Approval ___________________________________

Contractor ________________________________________ Approval _________________________________________ Contractor's P.O. No. _______________________________ Representative ____________________________________

SKU _____________________________________________

Engineering Specification

ES-D-SnapFastQD

Dormont product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Dormont Technical Service. Dormont reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Dormont products previously or subsequently sold. Refer to the owner's manual for warranty information.

The information contained herein is not intended to replace the full product installation and safety information available or the experience of a trained product installer. You are required to thoroughly read all installation instructions and product safety information before beginning the installation of this product.

NOTICE

Dormont 1675KIT48 Item #4 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 14

SnapFast® Quick-Disconnect Deluxe Kit Assembly

Ordering Information

CONFIGURATION SIZE I.D. 24" (607MM) 36" (914MM) 48" (1,219MM) 60" (1,524MM) 72" (1,829MM)

Deluxe Kit*

½"

1650KIT24 1650KIT36 1650KIT48 1650KIT60 1650KIT72

Basic Kit** 1650BPQR24 1650BPQR36 1650BPQR48 1650BPQR60 1650BPQR72

Hose Assembly*** 1650BPQ24 1650BPQ36 1650BPQ48 1650BPQ60 1650BPQ72

Deluxe Kit*

¾"

1675KIT24 1675KIT36 1675KIT48 1675KIT60 1675KIT72

Basic Kit** 1675BPQR24 1675BPQR36 1675BPQR48 1675BPQR60 1675BPQR72

Hose Assembly*** 1675BPQ24 1675BPQ36 1675BPQ48 1675BPQ60 1675BPQ72

Deluxe Kit*

1"

16100KIT24 16100KIT36 16100KIT48 16100KIT60 16100KIT72

Basic Kit** 16100BPQR24 16100BPQR36 16100BPQR48 16100BPQR60 16100BPQR72

Hose Assembly*** 16100BPQ24 16100BPQ36 16100BPQ48 16100BPQ60 16100BPQ72

Deluxe Kit*

1¼"

16125KIT24 16125KIT36 16125KIT48 16125KIT60 16125KIT72

Basic Kit** 16125BPQR24 16125BPQR36 16125BPQR48 16125BPQR60 16125BPQR72

Hose Assembly*** 16125BPQ24 16125BPQ36 16125BPQ48 16125BPQ60 16125BPQ72

BTU/hr Flow Capacity Natural Gas (Flow rating BTU/hr 0.64 SP. GR. @ 0.5 inch WC pressure drop)

LENGTH

MODEL SIZE I.D. 24" (607MM) 36" (914MM) 48" (1,219MM) 60" (1,524MM) 72" (1,829MM)

1650BPQ ½" 87,000 77,000 68,000 60,000 55,000

1675BPQ ¾" 232,000 218,000 180,000 158,000 139,000

16100BPQ 1" 414,000 379,000 334,000 294,000 279,000

16125BPQ 1¼" 699,000 615,000 541,000 476,000 419,000

* Deluxe Kits include: The Dormont Blue Hose and restraining device, full port valve and (2) street elbows **Basic Kits include: The Dormont Blue Hose and restraining device, street elbow and SnapFast ***Hose Assemblies include: The Dormont Blue Hose, SnapFast and street elbow

Approvals & Certifications

NSF/ANSI 169 – Special-purpose food equipment and devices ANSI Z21.69 / CSA 6.16 – Connectors for moveable gas appliances ANSI Z21.41 / CSA 6.9 – Quick-disconnect devices for use with gas fuel appliances ANSI Z21.15 / CSA 9.1 – Manually operated gas valves for appliances, appliance connectors Meets requirements of ANSI Z223.1 / NFPA 54 National Fuel Gas Code Not for use in temperatures less than 32°F (0°C). For indoor use only.

Max operating pressure 1/2 psi.

Refer to the catalog for additional approvals and certifications or go to www.dormont.com.

A restraining device is required for all moveable gas equipment.

ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 15

Ordering Information

CONFIGURATION SIZE I.D. 24" (607MM) 36" (914MM) 48" (1,219MM) 60" (1,524MM) 72" (1,829MM)

Deluxe Kit*

½"

1650KIT24 1650KIT36 1650KIT48 1650KIT60 1650KIT72

Basic Kit** 1650BPQR24 1650BPQR36 1650BPQR48 1650BPQR60 1650BPQR72

Hose Assembly*** 1650BPQ24 1650BPQ36 1650BPQ48 1650BPQ60 1650BPQ72

Deluxe Kit*

¾"

1675KIT24 1675KIT36 1675KIT48 1675KIT60 1675KIT72

Basic Kit** 1675BPQR24 1675BPQR36 1675BPQR48 1675BPQR60 1675BPQR72

Hose Assembly*** 1675BPQ24 1675BPQ36 1675BPQ48 1675BPQ60 1675BPQ72

Deluxe Kit*

1"

16100KIT24 16100KIT36 16100KIT48 16100KIT60 16100KIT72

Basic Kit** 16100BPQR24 16100BPQR36 16100BPQR48 16100BPQR60 16100BPQR72

Hose Assembly*** 16100BPQ24 16100BPQ36 16100BPQ48 16100BPQ60 16100BPQ72

Deluxe Kit*

1¼"

16125KIT24 16125KIT36 16125KIT48 16125KIT60 16125KIT72

Basic Kit** 16125BPQR24 16125BPQR36 16125BPQR48 16125BPQR60 16125BPQR72

Hose Assembly*** 16125BPQ24 16125BPQ36 16125BPQ48 16125BPQ60 16125BPQ72

The Dormont Blue Hose®

The Dormont Blue Hose is a commercial, moveable-grade gas connector designed for use with moveable equipment.

Moveable equipment is defined in ANSI Standard Z21.69/CSA 6.16 as gas utilization equipment that may be mounted on casters or otherwise be subject to movement.

• One-handed quick-disconnect fitting

• Thermal shut-off when internal temperature exceeds

350°F (177°C)

Restraining Device

• ANSI Z21.69 Standard section 1.7.4 states: Connectors when used on caster-mounted equipment shall be installed with a restraining device, which prevents transmission of the strain to the connector

We guarantee our commercial gas connectors for the life of the original appliance to which it is connected.

Typical Installation

ES-D-SnapFastQD 2110 © 2021 Dormont

USA: T: (800) 367-6668 • F: (724) 733-4808 • Dormont.com

Safety-Set®

Benefits

• Can be used with all caster-mounted equipment including cooking appli-ances, warming carts, salad bars, and refrigerators

• Crush Resistant

• Resistant to oils and greases

• Open-floor design allows appliance to rest level on the floor to ensure even cooking

Features

• Compatible with 4", 5", and 6" casters

• Certified to NSF/ANSI Standard 169 – Special Purpose Food

Equipment & Devices

• Flexible, tough injection molded Thermoplastic Polyurethane

(TPU)

• Able to withstand 1,000 PSI of crush pressure

Ordering Instructions:

The Saftey-Set wheel positioning product can be ordered individually or with the Blue Hose Kit.

The Safety-Set model name is "PS" and the ordering number is 0241002.

When ordering the Safety-Set with the Blue Hose kit, simply add the letters "PS" to the end of the model number.

Options ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 16

O V E N S

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

Item # C.S.I. Section 11420

F41030 (06/19)

VCH88

COOK AND HOLD OVEN

Model VCH88

R

UL listed. UL listed to Canadian safety standards.

Classified by UL to NSF Standard #4.

SPECIFICATIONS

Vulcan Model No. VCH88 Cook and Hold Oven with capacity for sixteen 18" x 26" sheet pans on 3" centers or thirty-two 12" x 20" x 2½" steam table pans. Solid state controls capable of cooking at temperatures up to 350ºF and holding at temperatures up to 250ºF. Unit can also be used to rethermalize products. Knob style controls set the cooking time, cooking temperature, and holding temperature. Digital display shows time in minutes, cooking temperature, holding temperature, and oven temperature. Controls may also be programmed with nine custom programs. The low speed fan provides even heat distribution and natural browning of meat products. Ovens come with 10 pairs of removable universal tray slides and 4 wire pan cooking grids. Unit comes with 20 gauge stainless steel inside and out, an integrated steel frame, full insulation, a removable control/power module, 5" heavy duty casters (2 swivel with brakes and 2 rigid), magnetic action door latch plus a 10-year warranty on heating elements. Dual voltage 208/240 volt, single phase, 50/60 Hz, complete with two cords and plugs (NEMA 6-30).

Exterior Dimensions:

271⁄4" W x 36" D x 81" H on 5" heavy duty casters (2 swivel with brakes, 2 rigid)

STANDARD FEATURES

■ Cook and hold oven with capacity for sixteen 18" x 26" sheet pans on 3" centers or thirty-two 12" x 20" x 2½" steam table pans

■ Cook at temperatures up to 350ºF (177ºC)

■ Hold at temperatures up to 250ºF (121ºC)

■ Unit can also be used to rethermalize products

■ Knob style controls set the cooking time, cooking temperature, and holding temperature

■ No ventilation hood required (in most areas)

■ Digital LED display shows: time in minutes, hold temperature, cook temperature, and cabinet temperature

■ Controls may also be programmed with nine custom programs

■ Low speed fan provides even heat distribution and natural browning of meat products

■ Removable control/power module

■ Provided with 10 pairs of removable universal tray slides adjustable on 1½" centers

■ Provided with 4 wire pan grid cooking racks

■ Interior and exterior are both constructed out of 20 gauge stainless steel

■ Integrated steel frame for maximum strength

■ Fully insulated 2" in top and 1" in sides and bottom

■ Magnetic action door latch and heavy duty hinges secured to internal frame

■ 5" Heavy duty casters (2 swivel with brakes and 2 rigid)

■ Dual voltage 208/240 volt, single phase, 50/60 hz

■ Complete with two cords and plugs (NEMA 6-30)

■ 10-year warranty on heating elements

OPTIONS

Left hand hinged door

Additional universal tray slides

Additional cooking racks

VENTILATION REQUIREMENTS

This cabinet passes the EPA Method 202 test and complies with Section 59 of UL710B for emission of grease-laden air. A ventilation hood is not required in most areas. Check local codes. Copies of the EPA 202 test procedure and results are available for inspector review.

Vulcan VCH88 Item #5 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 17 http://www.vulcanequipment.com http://www.vulcanequipment.com/Products/VCH-Institutional-Series/

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: 1-800-444-0602

O V E N S

NOTE: In line with its policy to continually improve its products, Vulcan reserves the right to change materials and specifications without notice.

F41030 (06/19)

PAN

CAPACITY

EXTERIOR

DIMENSIONS

ELECTRICAL

PER COMPARTMENT SHIPPING WEIGHTS

LBS / KG

VOLTS WATTS AMPS

16 Baking Pans:

18" x 26" x 1" or 32 Steam Table Pans:

12" x 20" x 21⁄2"

271⁄4" W x 36" D x 81" H

3,800 5,060

565 lbs. / 256 kg.

This appliance is manufactured for commercial use only and is not intended for home use.

VCH88

COOK AND HOLD OVEN

Allow 4" of clearance on each side for ventilation.

Vulcan VCH88 Item #5 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 18

SERVING THE FOOD INDUSTRY SINCE 1951

COOKING EQUIPMENT

COUNTERTOP DOUBLE TANK ELECTRIC

PASTA COOKER

Item: 41883 Model: CE-CN-0008-P

Authorized Dealer

Durable stainless steel construction

Front sliding door for water refill and waste outlet

Two 9L water tanks

Baskets included

Non-slip feet

Omcan USA 41883 Item #6 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 19

TECHNICAL SPECIFICATIONS

ITEM NUMBER 41883

MODEL CE-CN-0008-P

CAPACITY 9L (x2)

NUMBER OF BASKET 8 circular; 4 rectangular

MAX. TEMPERATURE 110°C/ 230°F

POWER 7200 watt

AMPERAGE 30A

ELECTRICAL 240v/60hz/1ph

NET

DIMENSIONS

28” x 21.75” x 19”/ 711 x 552.45 x 482.6 mm

GROSS

DIMENSIONS

47” x 36” x 24” /

1193.8 x 914.4 x 609.6 mm

NET WEIGHT 30 kg/ 66 lbs.

GROSS WEIGHT 49.4 kg/ 109 lbs.

13”

6”

3.5”

BARE WIRE

7”

9.8”

6”

4”

OMCAN INC.

Telephone: 1-800-465-0234 Fax: (905) 607-0234 Email: sales@omcan.com Website: www.omcan.com

OMCAN INC. Follow us to keep up to date with the latest news and offers

2019.E.O.E

COOKING EQUIPMENT

COUNTERTOP DOUBLE TANK ELECTRIC

PASTA COOKER

19.5”

9.5” 12”5”

21.5”

2”

4”4”

28”

21.75”

.5

Omcan USA 41883 Item #6 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 20

3601 S. Banker St. Effingham, IL 62401 • P.O. BOX 609 • Ph: (888) 431-2667 • Fax: (800) 433-2667

ITEM #: QTY:

MODEL #:

PROJECT NAME:

FEATURES:

• 16GA TYPE 300 STAINLESS STEEL TOP WITH #4 POLISH,

SATIN FINISH

• 1-1/2" STALLION EDGE ON FRONT. TURNED UP BACK AND

BOTH SIDES

• TOP FRAME IS REINFORCED BY A FULL FRAME FABRICATED

OF 1-1/2" SQUARE O.D. TUBE 16GA STAINLESS STEEL

• STAINLESS STEEL BASE

• SHIPPED KNOCKED-DOWN, EASY - TO - ASSEMBLE

CONSTRUCTION:

• TOP: STAINLESS STEEL TOPS

ARE TIG WELDED, EXPOSED WELDS ARE

POLISHED TO MATCH ADJACENT SURFACE

MATERIAL:

• TOP: 16GA STAINLESS STEEL TYPE 300

STAINLESS STEEL WITH #4 POLISH, SATIN

FINISH

• SHELF: 18GA STAINLESS STEEL

• LEGS: 1-5/8" ROUND O.D. 16 GA

TUBULAR STAINLESS STEEL

• GUSSETS: STAINLESS STEEL

• FEET: 1" ADJUSTABLE STAINLESS BULLET

FEET

"GS6-SSK" EQUIPMENT STANDS W/ STAINLESS SHELF BASE

24" WIDE QTY 30" WIDE QTY 36" WIDE QTY

GS6-2415SSK GS6-3015SSK GS6-3615SSK

GS6-2418SSK GS6-3018SSK GS6-3618SSK

GS6-2424SSK GS6-3024SSK GS6-3624SSK

GS6-2430SSK GS6-3030SSK GS6-3630SSK

GS6-2436SSK GS6-3036SSK GS6-3636SSK

GS6-2448SSK GS6-3048SSK GS6-3648SSK

GS6-2460SSK GS6-3060SSK GS6-3660SSK

GS6-2472SSK GS6-3072SSK GS6-3672SSK

OPTIONAL ACCESSORIES

DESCRIPTION QTY

MAPLE CUTTING BOARDS

WELDED SET-UP

"GS6-SSK" EQUIPMENT STANDS

STAINLESS STEEL BASE

070919

John Boos GS6‐2430SSK Item #7 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 21

VHABYNChowS Highlight

3601 S. Banker St. • Effingham, IL 62401 • PO BOX 609 • quotes@johnboos.com www.johnboos.com

John Boos & Co. is constantly engaged in a program of improving products and therefore reserves the right to change specifications without prior notice.

SOME UNITS SHIP UNASSEMBLED FOR REDUCED SHIPPING COST. ALL DIMENSIONS ARE TYPICAL. TOLERANCE +/- .500"

DETAILED SPECIFICATIONS

"GS6-SSK" EQUIPMENT STANDS W/ STAINLESS STEEL SHELF BASE

LENGTH 24" WIDE WT. (LBS) 30" WIDE WT. (LBS) 36" WIDE WT. (LBS)

15" GS6-2415SSK 30 GS6-3015SSK 36 GS6-3615SSK 38

18" GS6-2418SSK 36 GS6-3018SSK 40 GS6-3618SSK 44

24" GS6-2424SSK 47 GS6-3024SSK 51 GS6-3624SSK 55

30" GS6-2430SSK 60 GS6-3030SSK 63 GS6-3630SSK 80

36" GS6-2436SSK 65 GS6-3036SSK 69 GS6-3636SSK 73

48" GS6-2448SSK 80 GS6-3048SSK 90 GS6-3648SSK 100

60" GS6-2460SSK 95 GS6-3060SSK 111 GS6-3660SSK 127

72" GS6-2472SSK * 111 GS6-3072SSK * 132 GS6-3672SSK * 154

112020

*NOTE: 3 SETS OF LEGS

John Boos GS6‐2430SSK Item #7 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 22

ITEM #: QTY:

MODEL #:

PROJECT NAME:

John Boos & Co. is constantly engaged in a program of improving products and therefore reserves the right to change specifications without prior notice.

SOME UNITS SHIP UNASSEMBLED FOR REDUCED SHIPPING COST. ALL DIMENSIONS ARE TYPICAL. TOLERANCE +/- .500"

3601 S. Banker St. • Effingham, IL 62401 • PO BOX 609 • quotes@johnboos.com www.johnboos.com378

3601 S. Banker St. Effingham, IL 62401 • P.O. BOX 609 • Ph: (888) 431-2667 • Fax: (800) 433-2667

CASTERS & FEET

MODEL # QTY ITEM DESCRIPTION SET OF

CAS01-R CASTERS 5", HEAVY DUTY, LOCKING, FOR 1-5/8"

DIAMETER LEGS 4

CAS02-R CASTERS 5", HEAVY DUTY, LOCKING, FOR 1-5/8"

DIAMETER LEGS 6

CAS03 CASTERS 2-1/2", HEAVY DUTY, LOCKING 4

CAS-RN CASTERS 3", BLACK, LOCKING 4

CAS23-R CASTERS 5", HEAVY DUTY, LOCKING,

FOR 2" SQUARE TUBE 4

CUCCAS-DLGS CASTERS 5", SWIVEL LOCKING PLATE CASTER 4

CAS05 FLANGE FEET ADJUSTABLE, STAINLESS STEEL 4

CAS05H FLANGE FEET ADJUSTABLE WITH HOLES FOR

ATTACHMENT TO FLOOR, STAINLESS STEEL 4

CASWS05-4 CASTERS LOCKING W/ BUMPERS 4

CAS06 FLANGE FEET ADJUSTABLE, STAINLESS STEEL 6

CAS06H FLANGE FEET ADJUSTABLE WITH HOLES FOR

ATTACHMENT TO FLOOR, STAINLESS STEEL 6

CAS07 BULLET FOOT ADJUSTABLE, STAINLESS STEEL EACH

CAS07-4 BULLET FOOT ADJUSTABLE, STAINLESS STEEL, ONE (1)

EACH PER LEG OF TABLE 4

CAS07-6 BULLET FOOT ADJUSTABLE, STAINLESS STEEL, FOR

1-5/8" DIA. LEG 6

CAS08 BULLET FOOT ADJUSTABLE, STAINLESS STEEL, FOR 1-1/2"

SQUARE LEG EACH

CAS08-4 BULLET FOOT ADJUSTABLE, STAINLESS STEEL, FOR 1-1/2"

SQUARE LEG 4

CAS08-6 BULLET FOOT ADJUSTABLE, STAINLESS STEEL, FOR 1-1/2"

SQUARE LEG 6

CAS12-1 FLANGE FEET ADJUSTABLE, STAINLESS STEEL, (W/

MOUNTING HOLES) EACH

CAS14 CASTERS 5", HEAVY DUTY, LOCKING 4

CAS14-6 CASTERS 5", HEAVY DUTY, LOCKING 6

CAS15 FLANGE FEET ADJUSTABLE, STAINLESS STEEL EACH

CAS16 FLANGE FEET ADJUSTABLE, STAINLESS STEEL, 3-1/2" DIA. 4

CAS17 FLANGE FEET ADJUSTABLE, STAINLESS STEEL, 3-1/2"

DIA., (TABLES 84" & LONGER WITH 6 LEGS) 6

"CAS" CASTERS & FEET

021521

CAS01-R

CASWS05-4

CAS07

CAS03

CAS-RN

John Boos CAS01‐R Item #7 ebuy # 1558396 ‐ VAMC Manha an ‐ Kitchen Government Sales LLC Page: 23

G R I D D L E S & B R O I L E R S

P.O.