2169_SpecialPackaging.pdf

Statement of Work June 2020

PRESERVATION, PACKAGING & MARKING REQUIREMENTS

The contractor shall develop, implement and maintain the preservation, packaging and packing of all items to be delivered under the terms of this contract. Packaging procedures will be established in accordance with AFMCI 24- 201, specifically Paragraph 3.7 and MIL-STD-2073-1, Standard Practice for Military Packaging, Packaging requirements are identified in the AFMC Form 158, Packaging Requirements submitted by the responsible packaging specialist. All “markings and labeling” of shipments shall conform to MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage. The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

(ISPM 15) REQUIREMENTS

The contractor shall use the wood packaging material regulation for international trade which describes Phytosanitary (including treatments) that have been approved for wood packaging material and provides for the approval of new or revised treatments. Use the latest revision of (ISPM 15), and the following statement complies with the United Nations-implemented restrictions on wood packaging material (WPM).

“This requirement is specifically concerned with invasive species such as pinewood nematode. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frames, and cleats. The statement below cites the requirements in detail and covers lumber for building containers and pallets used for deliveries resulting in worldwide shipments (direct vendor deliveries, Air Logistics complex (ALC), Container Consolidation Points (CCP), Aerial Ports, Water Ports, or other DoD installations).

ELECTROSTATIC MATERIAL (When Applicable)

The Contractor shall apply provisions of MIL-STD-2073-1, when identifying all solid state devices and modules containing diodes, translators, integrated circuits and/or other microelectronic components sensitive to electrostatic forces. All such items shall be packaged IAW MIL- STD-2073- 1 using electrostatic free barrier materials and shall clearly bear “Electrostatic Sensitive Device” labels IAW MIL-STD-129, Department of Defense Standard Practice Military Marking for Shipment and Storage.

PALLETIZED UNIT LOADS

The Contractor shall apply provisions and methods of MIL-STD-147, Palletized Unit Loads to contracts requiring the preparation and shipment of bonded palletized unit loads for DoD facilities when applicable.

SPECIALIZED SHIPPING CONTAINERS

The contractor shall apply provisions of MIL-STD-648, Department of Defense Design Criteria Standard, Specialized Shipping Containers. This standard establishes general design guidelines and associated tests for specialized shipping containers used by the Department of Defense. Definitive requirements for specific containers will be defined by the individual specification, acquisition, or task order. This standard is intended to be used as the basic reference document in all specifications and standards prescribing performance requirements to be applied to a specialized shipping container. Compliance with this intent is expected through normal application of the specification or standard preparation and revision processes.

Statement of Work (Cont)

HAZARDOUS MATERIALS (When Applicable)

The contractor shall ensure Hazardous shipments comply with International Civil Aviation Organization (ICAO), U.S. Code of Federal Regulations (CFR) Title 49, International Air Transport Association (IATA) Dangerous Goods Regulation, International Maritime Dangerous Goods Code (IMDG, Annex 1), and AFMAN 24-204, Preparing Hazardous Materials for Military Air Shipments. Packaging shall meet “DOT specification or a United Nation (UN) specification ” manufactured in accordance with 49 CFR, Part 178 and the final packages assembled IAW 49 CFR, Parts 100-185 as applicable. A Competent Authority Approval (CAA) shall be acquired from the responsible Associate Administrator or other designated Department official to perform a function requiring prior consent under the Hazardous Material Regulation (HMR). Package(s) shall be marked IAW MIL-STD-129, DoD Standard Practice, Military Marking for Shipment and Storage.

The contractor shall affix a completed DD Form 1574, Serviceable Tag-Materiel or DD Form 1574-1, Serviceable Label- Materiel to each unit pack or intermediate container and prime outer container(s). The tag or label will indicate the condition(s) of the materiel and to identify the individual article or contents, bundle, container to which they are securely attached. If a symbol is used to represent the manufacturer or the approval agency certifying compliance with 49 CFR 178, subparts L and M, the symbol must be registered with the U.S. Department of Transportation. A copy of the Contractor’s Test Report and signed certification that the package configuration meets both CFR and UN requirements shall be made available to the procuring contract office, as required, prior to acceptance or shipment of any portion of the product IAW Contract Data Requirements List (CDRL DI-PACK-81059A) (Reference AFMC Form 158). Safety Data Sheets (SDS) are required for known hazardous items and applicable items shown in FED-STD-313, Tables I and II. The SDS shall have any applicable identification number, such as National Stock Number or Special Item Number. A copy of the SDS shall be mailed or e-mailed no later than five (5) days prior to contractual delivery of items:

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data

SPECIAL PACKAGING INSTRUCTIONS RETRIEVAL & EXCHANGE SYSTEM

(SPIRES)

Contractors may request the use of SPIRES website to view item packaging requirements or search for Special Packaging Instruction drawings via the following website: https://lts.cce.af.mil/SPIRES/.

REUSABLE CONTAINERS

The contractor shall safeguard all received reusable shipping containers that meet the requirements of the AFMC Form 158 and are suitable for return shipment of serviceable assets. The contractor shall dispose of and replace unserviceable containers with new containers that meet requirements of the AFMC Form 158.

Contact the Product Support Manager and Administering Contracting Office (ACO) for disposition instructions and replacement when Long Life Reusable Container(s) are received in an unserviceable condition.

REPORTING DISCREPANCIES

The contractor shall use Web Supply Discrepancy Report (WebSDR) to submit/reply to a Supply Discrepancy Report (SDR), when improperly packed assets are received/shipped in other than the contracted packaging requirements (coded data or Special Packaging Instructions (SPI) drawings) from Department of Defense (DoD) components or contractor activities. The contractor shall request a WebSDR account via the following website: https://www.transactionservices.dla.mil/daashome/homepage.asp

(See Defense Logistics Management (DLM) 4000.25-M, Volume 2, Supply Standard and Procedures, Chapter 17, Supply Discrepancy Reporting) http://www.dla.mil/HQ/InformationOperations/DLMS/

Exceptions when no damage has occurred are as follows:

- Items packaged before the current SPIdate.

- An alternate pack may be used, provided the prime Air Force Sustainment Complex, Packaging Office at the Air Logistics Complex (ALC) approves and issues a waiver, deviation number, which would be annotated on the exterior container on the lower right hand portion of the identification side of the container.

- In accordance with Technical Order (TO) 00-85B-3, How to Package Air Force Spares, the contractor may substitute the next larger size fast pack, of the type I or type II to ship transportation priorities 1 and 2 shipments as long as there is no decrease in any of the container dimensions without the requirement of a waiver deviation. TO 00- 85B-3, para 4.2 can be accessed via the website:

- https://www.tinker.af.mil/Portals/106/Documents/Technical%20Orders/AFD-082416-00-85B-3.pdf

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions The contractor shall use the ASSIST website to access specification, standards, data item descriptions documents listed in this contract solicitation:

FAR 52-211-2 Availability of Specifications, Standards, and Data Item Descriptions listed in the Acquisition Streamlining and Standardization Information System https://quicksearch.dla.mil/

AFSC

406 SCMS/GULAA

Attn: Keith Restorff

DSN: 777-9192

COMM: 801-777-9192

E-mail: keith.restorff@us.af.mil

APPLICABLE GOVERNMENT PACKAGING DOCUMENTS

NOTE: UTILIZE THE MOST RECENT REVISION

AFI 24-602V2_AFGM2018-01, Preparation and Movement of Air Force Cargo

AFMAN 24-204, Preparing Hazardous Materials for Military Air Shipments

DLMS 4000.25, Defense Logistics Management Systems, Volume 2, Change 10, Supply Standards and Procedures, Chapter 17, Supply Discrepancy Reporting

DOT Title 29, Occupational Safety and Health Administration, Labor

DOT Title 49, Code of Federal Regulations (49 CFR), Transportation

International Civil Aviation Organization (ICAO) Technical Instructions

International Air Transport Association (IATA) Dangerous Goods Regulation

International Maritime Dangerous Goods (IMDG) Code

ISPM 15, International Standard Phytosanitary Measure Note: Marking Requirements may be found in the American Lumber Standards Committee, Incorporated Wood Packaging Material Enforcement Regulations dated November 07, 2014 and ISPM 15.

MIL-STD-2073-1E, Change 3, Standard Practice, for Military Packaging

MIL-STD-129R, Change 1, Department of Defense Standard Practice Military Marking for Shipment and Storage

MIL-STD-648E, Department of Defense Design Criteria Standard, Specialized Shipping Containers

MIL-STD-147E, Change 1, Palletized Unit Loads

MIL-STD-1686C, Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices) TO 00-85B-3, How to Package Air Force Spares

FED-STD-313E, Federal Standard: Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities

MIL-STD-1686C, Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices).

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DEPARTMENT OF DEFENSE AND U.S. DOD CONTRACTORS ONLY, ADMINISTRATIVE OR OPERATIONAL USE, 01 MARCH 2018. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO 406

SCMS/GULAA, (PACKAGING DIVISION), HILL AFB, UTAH 84056.

DESTRUCTION NOTICE: FOLLOW THE PROCEDURES IN DOD 5220.22-M, NATIONAL INDUSTRIAL SECURITY PROGRAM OPERATING MANUAL (NISPOM), SECTION 5-705, OR DOD 5200.1-R, INFORMATION SECURITY PROGRAM, CHAPTER VI. FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

CAUTION NOTICES

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

REVISION OF ISPM NO. 15

REVISION OF WOOD PACKAGING MATERIAL FOR INTERNATIONAL TRADE

THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD

PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE

PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND

COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES, RESULTING IN SHIPMENTS WORLDWIDE

(DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES).

WOODEN LUMBER, WOODEN PALLET AND PACKAGING/CONTAINER STATEMENT:

ALL WOODEN LUMBER, WOODEN PALLETS, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD

PACKAGING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF

HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES).

CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS

COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF "INTERNATIONAL STANDARDS FOR

PHYTOSANITARY MEASURES (ISPM NO. 15), "REGULATION OF WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE."

NOTES

1. DESICCANT REF.-12 NEEDS TO BE PLACED IN INTERIOR CONTAINER REF.-6, BUT NOT TOUCHING ITEM.

2. PLACE HUMIDITY INDICATOR REF.-13 INSIDE TOP FLAP, TAPED AS TO NOT BE TOUCHING DISICCANT OR UNWRAPPED

ITEM.

3. PLACE TAPED CONTAINER INTO BARRIER BAG, REF.-5 AND SEAL. PLACE IN CUSHIONED EXTERIOR CONTAINER.

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND U.S. DOD CONTRACTORS ONLY, ADMINISTRATIVE OR OPERATIONAL USE, 16 MARCH 2020. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO 406 SCMS/GULAA, (PACKAGING

DIVISION), HILL AFB, UTAH 84056.

DESTRUCTION NOTICE: FOLLOW THE PROCEDURES IN DOD 5220.22-M, NATIONAL INDUSTRIAL SECURITY PROGRAM OPERATING MANUAL (NISPOM), SECTION 5-705, OR DOD 5200.1-R, INFORMATION SECURITY PROGRAM, CHAPTER VI. FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

AutoCAD SHX Text

31 LBS

AutoCAD SHX Text

ITEM WT.

AutoCAD SHX Text

2169 MOD

AutoCAD SHX Text

MARCH 87

AutoCAD SHX Text

DD

AutoCAD SHX Text

FORM

AutoCAD SHX Text

LEVEL B:

AutoCAD SHX Text

LEVEL A:

AutoCAD SHX Text

CLOSURE

AutoCAD SHX Text

IAW: ASTM D1974

AutoCAD SHX Text

IAW: ASTM D6251

AutoCAD SHX Text

COMPUTER GENERATED

AutoCAD SHX Text

SPI NO. F01-508-4197

AutoCAD SHX Text

CODE ID

AutoCAD SHX Text 98747

AutoCAD SHX Text

DESIGN FRAGILITY G

AutoCAD SHX Text

SPEC STYLE TYPE CL VRTY GR TR

AutoCAD SHX Text

AS SPECIFIED BELOW AND BILL OF MATERIALS

AutoCAD SHX Text

ILL.

AutoCAD SHX Text

NATIONAL STOCK NO.

AutoCAD SHX Text

PART OR DRAWING NO.

AutoCAD SHX Text

CURRENT

AutoCAD SHX Text

SPECIAL MARKINGS:

AutoCAD SHX Text

A) SPI NO. F01-508-4197

AutoCAD SHX Text

PRESERVATIVE: N/A

AutoCAD SHX Text

UNSERVICEABLE METHOD: GX

AutoCAD SHX Text

CLEANING & DRYING: IAW MIL-STD-2073

AutoCAD SHX Text

MILITARY PRESERVATION IAW MIL-STD-2073

AutoCAD SHX Text

B) REUSABLE CONTAINER & DUNNAGE DO NOT DESTROY.

AutoCAD SHX Text

MARKING IAW MIL-STD-129

AutoCAD SHX Text

AutoCAD SHX Text

QUP

AutoCAD SHX Text

ICQ

AutoCAD SHX Text

AutoCAD SHX Text

CNTR O.D.

AutoCAD SHX Text

LEVEL B:

AutoCAD SHX Text

ITEM DIM

AutoCAD SHX Text

LEVEL A:

AutoCAD SHX Text

CNTR I.D.

AutoCAD SHX Text

LEVEL B:

AutoCAD SHX Text

LEVEL A:

AutoCAD SHX Text

GROSS WT LBS

AutoCAD SHX Text

ITEM NOMENCLATURE

AutoCAD SHX Text

PACKING

AutoCAD SHX Text

LEVEL

AutoCAD SHX Text

GROSS CU FT

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

ASTM D5118

AutoCAD SHX Text

ASTM D6251

AutoCAD SHX Text

REV

AutoCAD SHX Text

DATE

AutoCAD SHX Text

ORIGINAL

AutoCAD SHX Text

CHK.

AutoCAD SHX Text

AUTH.

AutoCAD SHX Text P.S.

AutoCAD SHX Text

SPECIAL PACKAGING INSTRUCTION

AutoCAD SHX Text 15 7/8

AutoCAD SHX Text 18 3/8

AutoCAD SHX Text 6 1/4

AutoCAD SHX Text 30 5/8

AutoCAD SHX Text 28 1/8

AutoCAD SHX Text 17 3/4

AutoCAD SHX Text 18 7/8

AutoCAD SHX Text 16 1/2

AutoCAD SHX Text 7 3/4

AutoCAD SHX Text

LENGTH WIDTH DEPTH

AutoCAD SHX Text 15 1/2

AutoCAD SHX Text 16 1/4

AutoCAD SHX Text 28 1/2

AutoCAD SHX Text 27 3/4

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 16 3/4

AutoCAD SHX Text 15 3/4

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

LEVEL A LEVEL B

AutoCAD SHX Text 6.147

AutoCAD SHX Text A

AutoCAD SHX Text

III

AutoCAD SHX Text 4.263

AutoCAD SHX Text

SPI NO. (TPO)

AutoCAD SHX Text

SHEET 1 OF 4

AutoCAD SHX Text

K. KNIGHTON K. RESTORFF S. PEELER N. CORONADO

AutoCAD SHX Text

1280-01-508-4197 WF

AutoCAD SHX Text 8526047-920

AutoCAD SHX Text

COMPUTER, BOMB-NAVIGATIONAL

AutoCAD SHX Text F01-508-4197

AutoCAD SHX Text B

AutoCAD SHX Text V3c

AutoCAD SHX Text

RSC

AutoCAD SHX Text 20093

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

LTR

AutoCAD SHX Text

DATE

AutoCAD SHX Text

MARK THE SPI NUMBER ON THE IDENTIFICATION SIDE OF CONTAINER.

AutoCAD SHX Text

SERVICEABLE METHOD: GX

AutoCAD SHX Text

C) ESD LABELS REQUIRED

REQD

AutoCAD SHX Text P/N

AutoCAD SHX Text

QTY

AutoCAD SHX Text SIZE: (INCHES UNLESS SPECIFIED) TOLERANCES ON FRAC. ± , 18, DECIMAL ± .10, ANGLES ± 1°

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

NOMENCLATURE OR

AutoCAD SHX Text

SPECIFICATION

AutoCAD SHX Text

MATERIAL

AutoCAD SHX Text A/R A/R 1 1 2 2 2 2

AutoCAD SHX Text TAPE, PACKAGING WRAP, CUSHIONING BARRIER BAG CONTAINER, INTERIOR CUSHIONING, SIDE PLATEN CUSHIONING, END CUSHIONING, TOP & BOTTOM

AutoCAD SHX Text 3 X AS REQUIRED AS REQUIRED 29 X 16 (ID) 21 X 9 X 9 21 1/2 X 9 1/2 X 3 15 3/4 X 15 1/2 X 1/8 15 3/4 X 15 1/2 X 3 15 1/2 X 15 1/2 X 3

AutoCAD SHX Text ASTM D5486 TYPE I OR V A-A-59135 CLASS 1, GRADE B MIL-DTL-117 TYPE I, CLASS F, STYLE 1 ASTM D5118 RSC, CF, DOM, SW, GR. 200 MIL-PRF-26514 TYPE I, CLASS 2 ASTM D4727 CF, DOM, SW, GR. 200 MIL-PRF-26514 TYPE I, CLASS 2 MIL-PRF-26514 TYPE I, CLASS 2

AutoCAD SHX Text -8 -7 -6 -5 -4 -3 -2 -1

AutoCAD SHX Text

DD

AutoCAD SHX Text

2169C MOD

AutoCAD SHX Text

MARCH 87

AutoCAD SHX Text

FORM

AutoCAD SHX Text

COMPUTER GENERATED

AutoCAD SHX Text

SPECIAL PACKAGING INSTRUCTION

AutoCAD SHX Text

SPI NO. (TPO)

AutoCAD SHX Text

SHEET 2 OF 4

AutoCAD SHX Text

ITEM NOMENCLATURE

AutoCAD SHX Text 98747

AutoCAD SHX Text

CODE ID

AutoCAD SHX Text

COMPUTER, BOMB-NAVIGATIONAL

AutoCAD SHX Text F01-508-4197

CAUTION NOTICES

NOTICE 1: ASSETS PACKAGED IN ACCORDANCE WITH PREVIOUS ASSIGNED SPI F01-251-1150 DO NOT REQUIRE

REPACKAGING IF THE INTEGRITY OF THE SPI IS MAINTAINED AND ALL IDENTIFYING MARKINGS, TO INCLUDE SPI

NUMBER ARE OBLITERATED FROM EXTERIOR.

NOTICE 2: SEE SPIRES FOR A COMPLETE LISTING OF NSN's ASSIGNED TO THIS SPI.

NOTICE 3: PACKAGING MATERIAL MAY BE SUBSTITUTED IF IT MEETS THE REQUIREMENTS OF MIL-STD-2073, PROVIDES EQUAL OR BETTER PROTECTION AND THERE IS NO INCREASED COST TO THE GOVERNMENT.

NOTICE 4: FOR LEVEL A PACKAGING REQUIREMENTS, LEVEL B PACKS SHALL BE OVERBOXED IN A LEVEL A SPECIFIED

CONTAINER SHOWN ON PAGE 1 UNDER PACKAGING LEVEL A.

NOTICE 5: LEVEL A PROTECTION REQUIRED TO MEET THE MOST SEVERE WORLDWIDE SHIPMENT, HANDLING, AND

STORAGE CONDITIONS. EXAMPLES OF SITUATIONS ARE: WAR RESERVE MATERIAL, MOBILIZATION, STRATEGIC AND

THEATER DEPLOYMENT, OPEN STORAGE AND DECK LOADING. SECURITY ASSISTANCE ITEMS, INCLUDING FMS, ARE

ESPECIALLY SUSCEPTIBLE TO DAMAGE DUE TO UNKNOWN AND UNFAVORABLE TRANSPORTATION, CLIMATIC, AND

STORAGE CONDITIONS. PROVIDE LEVEL B PACKING UNLESS OTHERWISE DIRECTED BY THE PROCURING COUNTRY.

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES

REVISION OF ISPM NO. 15

REVISION OF WOOD PACKAGING MATERIAL FOR INTERNATIONAL TRADE

THE FOLLOWING STATEMENT IS IN COMPLIANCE WITH THE UNITED NATIONS-IMPLEMENTED RESTRICTIONS ON WOOD

PACKAGING MATERIAL (WPM). THIS REQUIREMENT IS SPECIFICALLY CONCERNED WITH INVASIVE SPECIES SUCH AS THE

PINEWOOD NEMATODE. WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. THE STATEMENT BELOW CITES THE REQUIREMENTS IN DETAIL AND

COVERS LUMBER FOR BUILDING CONTAINERS AND PALLETS USED FOR DELIVERIES, RESULTING IN SHIPMENTS WORLDWIDE

(DIRECT, OR THROUGH AIR LOGISTICS CENTERS (ALC), CONTAINER CONSOLIDATION POINTS (CCP), OR OTHER BASES).

WOODEN LUMBER, WOODEN PALLET AND PACKAGING/CONTAINER STATEMENT:

ALL WOODEN LUMBER, WOODEN PALLETS, AND WOODEN CONTAINERS PRODUCED ENTIRELY OR IN PART OF WOOD

PACKAGING MATERIAL (WPM) SHALL BE CONSTRUCTED FROM DEBARKED WOOD IN ADDITION TO THE APPLICATION OF

HEAT-TREATED (HT) MATERIAL (HT TO 56 DEGREES CENTIGRADE OR 133 DEGREES FAHRENHEIT FOR 30 MINUTES).

CERTIFICATION/MARKING IS REQUIRED BY AN ACCREDITED AGENCY RECOGNIZED BY THE AMERICAN LUMBER STANDARDS

COMMITTEE (ALSC). FOR REFERENCE DOCUMENTATION, SEE LATEST REVISION OF "INTERNATIONAL STANDARDS FOR

PHYTOSANITARY MEASURES (ISPM NO. 15), "REGULATION OF WOOD PACKAGING MATERIAL IN INTERNATIONAL TRADE."

NOTES

1. ENSURE NO IDENTIFYING MARKINGS, INCLUDING SPI, APPEAR ON THE EXTERIOR OF CONTAINER.

2. USE CUSHIONING WRAP, REF.-6, TO FILL ALL VOIDS AND ENSURE A SNUG FIT.

3. BATTERIES ARE TO BE REMOVED IAW T.O. 1F-16CG-2-94JG-70-3, 94-74-23, 2-3 PRIOR TO SHIPPING.

AutoCAD SHX Text

DD

AutoCAD SHX Text

2169C MOD

AutoCAD SHX Text

MARCH 87

AutoCAD SHX Text

FORM

AutoCAD SHX Text

COMPUTER GENERATED

AutoCAD SHX Text

SPECIAL PACKAGING INSTRUCTION

AutoCAD SHX Text

SPI NO. (TPO)

AutoCAD SHX Text

SHEET 3 OF 4

AutoCAD SHX Text

ITEM NOMENCLATURE

AutoCAD SHX Text 98747

AutoCAD SHX Text

CODE ID

AutoCAD SHX Text

COMPUTER, BOMB-NAVIGATIONAL

F01-508-4197

DD

AutoCAD SHX Text

2169C MOD

AutoCAD SHX Text

MARCH 87

AutoCAD SHX Text

FORM

AutoCAD SHX Text

COMPUTER GENERATED

AutoCAD SHX Text

SPECIAL PACKAGING INSTRUCTION

AutoCAD SHX Text

SPI NO. (TPO)

AutoCAD SHX Text

SHEET 4 OF 4

AutoCAD SHX Text

ITEM NOMENCLATURE

AutoCAD SHX Text 98747

AutoCAD SHX Text

CODE ID

AutoCAD SHX Text

COMPUTER, BOMB-NAVIGATIONAL

AutoCAD SHX Text F01-508-4197

AutoCAD SHX Text F01-508-4197

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

ITEM REFERENCE